From: Daniel Golle Date: Thu, 28 Jul 2022 14:45:03 +0000 (+0200) Subject: Revert "realtek: remove support for HPE 1920 series" X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=a49212d762fb2635564cd3365651da51d0c535d9;p=openwrt%2Fstaging%2Fjogo.git Revert "realtek: remove support for HPE 1920 series" This reverts commit a63aeaecf1f3387df020854c9b22a365207399ce. Signed-off-by: Daniel Golle --- diff --git a/target/linux/realtek/base-files/etc/board.d/02_network b/target/linux/realtek/base-files/etc/board.d/02_network index af9db848dd..5356bcac65 100644 --- a/target/linux/realtek/base-files/etc/board.d/02_network +++ b/target/linux/realtek/base-files/etc/board.d/02_network @@ -22,9 +22,20 @@ ucidef_set_bridge_device switch ucidef_set_interface_lan "$lan_list" lan_mac="" +lan_mac_start="" lan_mac_end="" label_mac="" case $board in +hpe,1920-8g|\ +hpe,1920-16g|\ +hpe,1920-24g) + label_mac=$(mtd_get_mac_binary factory 0x68) + lan_mac=$label_mac + mac_count1=$(hexdump -v -n 4 -s 0x110 -e '4 "%d"' $(find_mtd_part factory) 2>/dev/null) + mac_count2=$(hexdump -v -n 4 -s 0x114 -e '4 "%d"' $(find_mtd_part factory) 2>/dev/null) + lan_mac_start=$(macaddr_add $lan_mac 2) + lan_mac_end=$(macaddr_add $lan_mac $((mac_count2-mac_count1))) + ;; *) lan_mac=$(mtd_get_mac_ascii u-boot-env2 mac_start) lan_mac_end=$(mtd_get_mac_ascii u-boot-env2 mac_end) @@ -36,10 +47,11 @@ esac ucidef_set_interface_macaddr "lan" $lan_mac ucidef_set_bridge_mac "$lan_mac" ucidef_set_network_device_mac eth0 $lan_mac +[ -z "$lan_mac_start" ] && lan_mac_start=$lan_mac for lan in $lan_list; do - ucidef_set_network_device_mac $lan $lan_mac - [ -z "$lan_mac_end" ] || [ "$lan_mac" == "$lan_mac_end" ] && lan_mac=$(macaddr_setbit_la $lan_mac) - lan_mac=$(macaddr_add $lan_mac 1) + ucidef_set_network_device_mac $lan $lan_mac_start + [ -z "$lan_mac_end" ] || [ "$lan_mac_start" == "$lan_mac_end" ] && lan_mac_start=$(macaddr_setbit_la $lan_mac_start) + lan_mac_start=$(macaddr_add $lan_mac_start 1) done [ -n "$label_mac" ] && ucidef_set_label_macaddr $label_mac diff --git a/target/linux/realtek/dts-5.10/rtl8380_hpe_1920-8g.dts b/target/linux/realtek/dts-5.10/rtl8380_hpe_1920-8g.dts new file mode 100644 index 0000000000..b51c75f355 --- /dev/null +++ b/target/linux/realtek/dts-5.10/rtl8380_hpe_1920-8g.dts @@ -0,0 +1,113 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "rtl838x.dtsi" +#include "rtl838x_hpe_1920.dtsi" + +/ { + compatible = "hpe,1920-8g", "realtek,rtl838x-soc"; + model = "HPE 1920-8G (JG920A)"; + + gpio1: rtl8231-gpio { + compatible = "realtek,rtl8231-gpio"; + #gpio-cells = <2>; + gpio-controller; + indirect-access-bus-id = <0>; + }; + + i2c0: i2c-gpio-0 { + compatible = "i2c-gpio"; + sda-gpios = <&gpio1 23 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio1 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + i2c-gpio,delay-us = <2>; + #address-cells = <1>; + #size-cells = <0>; + }; + + sfp0: sfp-0 { + compatible = "sff,sfp"; + i2c-bus = <&i2c0>; + los-gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>; + mod-def0-gpio = <&gpio1 25 GPIO_ACTIVE_LOW>; + // tx-fault and tx-disable unconnected + }; + + i2c1: i2c-gpio-1 { + compatible = "i2c-gpio"; + sda-gpios = <&gpio1 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio1 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + i2c-gpio,delay-us = <2>; + #address-cells = <1>; + #size-cells = <0>; + }; + + sfp1: sfp-1 { + compatible = "sff,sfp"; + i2c-bus = <&i2c1>; + los-gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>; + mod-def0-gpio = <&gpio1 21 GPIO_ACTIVE_LOW>; + // tx-fault and tx-disable unconnected + }; +}; + +ðernet0 { + mdio: mdio-bus { + compatible = "realtek,rtl838x-mdio"; + regmap = <ðernet0>; + #address-cells = <1>; + #size-cells = <0>; + + INTERNAL_PHY(8) + INTERNAL_PHY(9) + INTERNAL_PHY(10) + INTERNAL_PHY(11) + INTERNAL_PHY(12) + INTERNAL_PHY(13) + INTERNAL_PHY(14) + INTERNAL_PHY(15) + + INTERNAL_PHY(24) + INTERNAL_PHY(26) + }; +}; + +&switch0 { + ports { + #address-cells = <1>; + #size-cells = <0>; + + SWITCH_PORT(8, 1, internal) + SWITCH_PORT(9, 2, internal) + SWITCH_PORT(10, 3, internal) + SWITCH_PORT(11, 4, internal) + SWITCH_PORT(12, 5, internal) + SWITCH_PORT(13, 6, internal) + SWITCH_PORT(14, 7, internal) + SWITCH_PORT(15, 8, internal) + + port@24 { + reg = <24>; + label = "lan9"; + phy-mode = "1000base-x"; + managed = "in-band-status"; + sfp = <&sfp0>; + }; + + port@26 { + reg = <26>; + label = "lan10"; + phy-mode = "1000base-x"; + managed = "in-band-status"; + sfp = <&sfp1>; + }; + + port@28 { + ethernet = <ðernet0>; + reg = <28>; + phy-mode = "internal"; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; +}; diff --git a/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-16g.dts b/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-16g.dts new file mode 100644 index 0000000000..59043b2f6f --- /dev/null +++ b/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-16g.dts @@ -0,0 +1,48 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "rtl8382_hpe_1920.dtsi" + +/ { + compatible = "hpe,1920-16g", "realtek,rtl838x-soc"; + model = "HPE 1920-16G (JG923A)"; +}; + +&switch0 { + ports { + #address-cells = <1>; + #size-cells = <0>; + + SWITCH_PORT(8, 1, internal) + SWITCH_PORT(9, 2, internal) + SWITCH_PORT(10, 3, internal) + SWITCH_PORT(11, 4, internal) + SWITCH_PORT(12, 5, internal) + SWITCH_PORT(13, 6, internal) + SWITCH_PORT(14, 7, internal) + SWITCH_PORT(15, 8, internal) + + SWITCH_PORT(16, 9, qsgmii) + SWITCH_PORT(17, 10, qsgmii) + SWITCH_PORT(18, 11, qsgmii) + SWITCH_PORT(19, 12, qsgmii) + SWITCH_PORT(20, 13, qsgmii) + SWITCH_PORT(21, 14, qsgmii) + SWITCH_PORT(22, 15, qsgmii) + SWITCH_PORT(23, 16, qsgmii) + + SWITCH_PORT(24, 17, qsgmii) + SWITCH_PORT(25, 18, qsgmii) + SWITCH_PORT(26, 19, qsgmii) + SWITCH_PORT(27, 20, qsgmii) + + port@28 { + ethernet = <ðernet0>; + reg = <28>; + phy-mode = "internal"; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; +}; diff --git a/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-24g.dts b/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-24g.dts new file mode 100644 index 0000000000..61781c708e --- /dev/null +++ b/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-24g.dts @@ -0,0 +1,68 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "rtl8382_hpe_1920.dtsi" + +/ { + compatible = "hpe,1920-24g", "realtek,rtl838x-soc"; + model = "HPE 1920-24G (JG924A)"; +}; + +&mdio { + EXTERNAL_PHY(0) + EXTERNAL_PHY(1) + EXTERNAL_PHY(2) + EXTERNAL_PHY(3) + EXTERNAL_PHY(4) + EXTERNAL_PHY(5) + EXTERNAL_PHY(6) + EXTERNAL_PHY(7) +}; + +&switch0 { + ports { + #address-cells = <1>; + #size-cells = <0>; + + SWITCH_PORT(0, 1, qsgmii) + SWITCH_PORT(1, 2, qsgmii) + SWITCH_PORT(2, 3, qsgmii) + SWITCH_PORT(3, 4, qsgmii) + SWITCH_PORT(4, 5, qsgmii) + SWITCH_PORT(5, 6, qsgmii) + SWITCH_PORT(6, 7, qsgmii) + SWITCH_PORT(7, 8, qsgmii) + + SWITCH_PORT(8, 9, internal) + SWITCH_PORT(9, 10, internal) + SWITCH_PORT(10, 11, internal) + SWITCH_PORT(11, 12, internal) + SWITCH_PORT(12, 13, internal) + SWITCH_PORT(13, 14, internal) + SWITCH_PORT(14, 15, internal) + SWITCH_PORT(15, 16, internal) + + SWITCH_PORT(16, 17, qsgmii) + SWITCH_PORT(17, 18, qsgmii) + SWITCH_PORT(18, 19, qsgmii) + SWITCH_PORT(19, 20, qsgmii) + SWITCH_PORT(20, 21, qsgmii) + SWITCH_PORT(21, 22, qsgmii) + SWITCH_PORT(22, 23, qsgmii) + SWITCH_PORT(23, 24, qsgmii) + + SWITCH_PORT(24, 25, qsgmii) + SWITCH_PORT(25, 26, qsgmii) + SWITCH_PORT(26, 27, qsgmii) + SWITCH_PORT(27, 28, qsgmii) + + port@28 { + ethernet = <ðernet0>; + reg = <28>; + phy-mode = "internal"; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; +}; diff --git a/target/linux/realtek/dts-5.10/rtl8382_hpe_1920.dtsi b/target/linux/realtek/dts-5.10/rtl8382_hpe_1920.dtsi new file mode 100644 index 0000000000..5368b41c27 --- /dev/null +++ b/target/linux/realtek/dts-5.10/rtl8382_hpe_1920.dtsi @@ -0,0 +1,117 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "rtl838x.dtsi" +#include "rtl838x_hpe_1920.dtsi" + +/ { + gpio1: rtl8231-gpio { + compatible = "realtek,rtl8231-gpio"; + #gpio-cells = <2>; + gpio-controller; + indirect-access-bus-id = <0>; + }; + + i2c0: i2c-gpio-0 { + compatible = "i2c-gpio"; + sda-gpios = <&gpio1 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio1 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + i2c-gpio,delay-us = <2>; + #address-cells = <1>; + #size-cells = <0>; + }; + + sfp0: sfp-0 { + compatible = "sff,sfp"; + i2c-bus = <&i2c0>; + los-gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>; + mod-def0-gpio = <&gpio1 21 GPIO_ACTIVE_LOW>; + // tx-fault unconnected + // tx-disable connected to RTL8214FC + }; + + i2c1: i2c-gpio-1 { + compatible = "i2c-gpio"; + sda-gpios = <&gpio1 23 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio1 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + i2c-gpio,delay-us = <2>; + #address-cells = <1>; + #size-cells = <0>; + }; + + sfp1: sfp-1 { + compatible = "sff,sfp"; + i2c-bus = <&i2c1>; + los-gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>; + mod-def0-gpio = <&gpio1 25 GPIO_ACTIVE_LOW>; + // tx-fault unconnected + // tx-disable connected to RTL8214FC + }; + + i2c2: i2c-gpio-2 { + compatible = "i2c-gpio"; + sda-gpios = <&gpio1 27 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio1 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + i2c-gpio,delay-us = <2>; + #address-cells = <1>; + #size-cells = <0>; + }; + + sfp2: sfp-2 { + compatible = "sff,sfp"; + i2c-bus = <&i2c2>; + los-gpio = <&gpio1 30 GPIO_ACTIVE_HIGH>; + mod-def0-gpio = <&gpio1 29 GPIO_ACTIVE_LOW>; + // tx-fault unconnected + // tx-disable connected to RTL8214FC + }; + + i2c3: i2c-gpio-3 { + compatible = "i2c-gpio"; + sda-gpios = <&gpio1 31 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio1 32 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + i2c-gpio,delay-us = <2>; + #address-cells = <1>; + #size-cells = <0>; + }; + + sfp3: sfp-3 { + compatible = "sff,sfp"; + i2c-bus = <&i2c3>; + los-gpio = <&gpio1 34 GPIO_ACTIVE_HIGH>; + mod-def0-gpio = <&gpio1 33 GPIO_ACTIVE_LOW>; + // tx-fault unconnected + // tx-disable connected to RTL8214FC + }; +}; + +ðernet0 { + mdio: mdio-bus { + compatible = "realtek,rtl838x-mdio"; + regmap = <ðernet0>; + #address-cells = <1>; + #size-cells = <0>; + + INTERNAL_PHY(8) + INTERNAL_PHY(9) + INTERNAL_PHY(10) + INTERNAL_PHY(11) + INTERNAL_PHY(12) + INTERNAL_PHY(13) + INTERNAL_PHY(14) + INTERNAL_PHY(15) + + EXTERNAL_PHY(16) + EXTERNAL_PHY(17) + EXTERNAL_PHY(18) + EXTERNAL_PHY(19) + EXTERNAL_PHY(20) + EXTERNAL_PHY(21) + EXTERNAL_PHY(22) + EXTERNAL_PHY(23) + + EXTERNAL_SFP_PHY_FULL(24, 0) + EXTERNAL_SFP_PHY_FULL(25, 1) + EXTERNAL_SFP_PHY_FULL(26, 2) + EXTERNAL_SFP_PHY_FULL(27, 3) + }; +}; diff --git a/target/linux/realtek/dts-5.10/rtl838x.dtsi b/target/linux/realtek/dts-5.10/rtl838x.dtsi index 11cabc3f63..41fdbdae20 100644 --- a/target/linux/realtek/dts-5.10/rtl838x.dtsi +++ b/target/linux/realtek/dts-5.10/rtl838x.dtsi @@ -27,6 +27,13 @@ reg = <##n>; \ }; +#define EXTERNAL_SFP_PHY_FULL(n, s) \ + phy##n: ethernet-phy@##n { \ + compatible = "ethernet-phy-ieee802.3-c22"; \ + sfp = <&sfp##s>; \ + reg = <##n>; \ + }; + #define SWITCH_PORT(n, s, m) \ port@##n { \ reg = <##n>; \ diff --git a/target/linux/realtek/dts-5.10/rtl838x_hpe_1920.dtsi b/target/linux/realtek/dts-5.10/rtl838x_hpe_1920.dtsi new file mode 100644 index 0000000000..8e29af62bb --- /dev/null +++ b/target/linux/realtek/dts-5.10/rtl838x_hpe_1920.dtsi @@ -0,0 +1,96 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include +#include + +/ { + chosen { + bootargs = "console=ttyS0,38400"; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x8000000>; + }; + + watchdog1: watchdog { + // PT7A7514 + compatible = "linux,wdt-gpio"; + gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>; + hw_algo = "toggle"; + hw_margin_ms = <1000>; + always-running; + + pinctrl-names = "default"; + pinctrl-0 = <&pinmux_disable_sys_led>; + }; +}; + +&watchdog0 { + status = "disabled"; +}; + +&spi0 { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <50000000>; + m25p,fast-read; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "bootware_basic"; + reg = <0x0 0x50000>; + read-only; + }; + + partition@0x60000 { + label = "bootware_data"; + reg = <0x60000 0x30000>; + read-only; + }; + + partition@0x90000 { + label = "bootware_extend"; + reg = <0x90000 0x40000>; + read-only; + }; + + partition@0x100000 { + label = "bootware_basic_backup"; + reg = <0x100000 0x50000>; + read-only; + }; + + partition@0x160000 { + label = "bootware_data_backup"; + reg = <0x160000 0x30000>; + read-only; + }; + + partition@0x190000 { + label = "bootware_extend_backup"; + reg = <0x190000 0x40000>; + read-only; + }; + + partition@0x300000 { + label = "firmware"; + compatible = "h3c,vfs-firmware"; + reg = <0x300000 0x1cf0000>; + }; + + partition@0x1ff0000 { + label = "factory"; + reg = <0x1ff0000 0x10000>; + read-only; + }; + }; + }; +}; diff --git a/target/linux/realtek/image/Makefile b/target/linux/realtek/image/Makefile index cf779002e8..6165d99bfc 100644 --- a/target/linux/realtek/image/Makefile +++ b/target/linux/realtek/image/Makefile @@ -8,6 +8,7 @@ KERNEL_ENTRY = 0x80000400 DEVICE_VARS += ZYXEL_VERS DLINK_KERNEL_PART_SIZE DEVICE_VARS += CAMEO_KERNEL_PART CAMEO_ROOTFS_PART CAMEO_CUSTOMER_SIGNATURE CAMEO_BOARD_VERSION +DEVICE_VARS += H3C_PRODUCT_ID H3C_DEVICE_ID define Build/zyxel-vers ( echo VERS;\ @@ -41,6 +42,43 @@ define Build/dlink-headers cat $@.kernel_part.hex $@.rootfs_part.hex > $@ endef +define Build/7z + $(STAGING_DIR_HOST)/bin/7zr a $(@).new -t7z -m0=lzma $(@) + mv $@.new $@ +endef + +define Build/h3c-image + $(STAGING_DIR_HOST)/bin/mkh3cimg \ + -i $(@) \ + -o $(@).new \ + -c 7z \ + -p $(H3C_PRODUCT_ID) \ + -d $(H3C_DEVICE_ID) + mv $@.new $@ +endef + +define Build/h3c-vfs + $(STAGING_DIR_HOST)/bin/mkh3cvfs \ + -i $(@) \ + -o $(@).new \ + -f openwrt-kernel.bin + mv $@.new $@ +endef + +define Build/relocate-kernel + rm -rf $@.relocate + $(CP) ../../generic/image/relocate $@.relocate + $(MAKE) -j1 -C $@.relocate KERNEL_ADDR=$(KERNEL_LOADADDR) LZMA_TEXT_START=0x82000000 \ + CROSS_COMPILE=$(TARGET_CROSS) + ( \ + dd if=$@.relocate/loader.bin bs=32 conv=sync && \ + perl -e '@s = stat("$@"); print pack("N", @s[7])' && \ + cat "$@" \ + ) > "$@.new" + mv "$@.new" "$@" + rm -rf $@.relocate +endef + define Device/Default PROFILES = Default KERNEL := kernel-bin | append-dtb | gzip | uImage gzip @@ -52,6 +90,17 @@ define Device/Default check-size | append-metadata endef +define Device/hpe_1920 + DEVICE_VENDOR := HPE + IMAGE_SIZE := 29632k + BLOCKSIZE := 64k + H3C_PRODUCT_ID := 0x3c010501 + KERNEL := kernel-bin | append-dtb | relocate-kernel | 7z | h3c-image | h3c-vfs + KERNEL_INITRAMFS := kernel-bin | append-dtb | relocate-kernel | 7z | h3c-image + IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | \ + pad-rootfs | check-size | append-metadata +endef + # "NGE" refers to the uImage magic define Device/netgear_nge KERNEL := kernel-bin | append-dtb | lzma | uImage lzma diff --git a/target/linux/realtek/image/rtl838x.mk b/target/linux/realtek/image/rtl838x.mk index 887f82e385..60eda5359d 100644 --- a/target/linux/realtek/image/rtl838x.mk +++ b/target/linux/realtek/image/rtl838x.mk @@ -65,6 +65,30 @@ define Device/engenius_ews2910p endef TARGET_DEVICES += engenius_ews2910p +define Device/hpe_1920-8g + $(Device/hpe_1920) + SOC := rtl8380 + DEVICE_MODEL := 1920-8G (JG920A) + H3C_DEVICE_ID := 0x00010023 +endef +TARGET_DEVICES += hpe_1920-8g + +define Device/hpe_1920-16g + $(Device/hpe_1920) + SOC := rtl8382 + DEVICE_MODEL := 1920-16G (JG923A) + H3C_DEVICE_ID := 0x00010026 +endef +TARGET_DEVICES += hpe_1920-16g + +define Device/hpe_1920-24g + $(Device/hpe_1920) + SOC := rtl8382 + DEVICE_MODEL := 1920-24G (JG924A) + H3C_DEVICE_ID := 0x00010027 +endef +TARGET_DEVICES += hpe_1920-24g + define Device/inaba_aml2-17gp SOC := rtl8382 IMAGE_SIZE := 13504k diff --git a/target/linux/realtek/rtl838x/config-5.10 b/target/linux/realtek/rtl838x/config-5.10 index c117fc489a..9075aa6d3c 100644 --- a/target/linux/realtek/rtl838x/config-5.10 +++ b/target/linux/realtek/rtl838x/config-5.10 @@ -74,6 +74,8 @@ CONFIG_GPIO_PCA953X=y CONFIG_GPIO_PCA953X_IRQ=y CONFIG_GPIO_REALTEK_OTTO=y CONFIG_GPIO_RTL8231=y +CONFIG_GPIO_WATCHDOG=y +# CONFIG_GPIO_WATCHDOG_ARCH_INITCALL is not set CONFIG_GRO_CELLS=y CONFIG_HANDLE_DOMAIN_IRQ=y CONFIG_HARDWARE_WATCHPOINTS=y @@ -134,6 +136,7 @@ CONFIG_MTD_SPI_NOR=y CONFIG_MTD_SPLIT_BRNIMAGE_FW=y CONFIG_MTD_SPLIT_EVA_FW=y CONFIG_MTD_SPLIT_FIRMWARE=y +CONFIG_MTD_SPLIT_H3C_VFS=y CONFIG_MTD_SPLIT_TPLINK_FW=y CONFIG_MTD_SPLIT_UIMAGE_FW=y CONFIG_NEED_DMA_MAP_STATE=y