From: Sebastian Reichel Date: Thu, 29 May 2014 06:57:29 +0000 (-0700) Subject: Input: tsc2005 - add DT support X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=a38cfebb56898633687ab337fd53710e63a0aedd;p=openwrt%2Fstaging%2Fblogic.git Input: tsc2005 - add DT support This adds DT support to the tsc2005 touchscreen driver. It also adds regulator support to the driver if booted via DT. Reviewed-by: Pavel Machek Acked-by: Aaro Koskinen Signed-off-by: Sebastian Reichel Signed-off-by: Dmitry Torokhov --- diff --git a/Documentation/devicetree/bindings/input/touchscreen/tsc2005.txt b/Documentation/devicetree/bindings/input/touchscreen/tsc2005.txt new file mode 100644 index 000000000000..4b641c7bf1c2 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/tsc2005.txt @@ -0,0 +1,42 @@ +* Texas Instruments tsc2005 touchscreen controller + +Required properties: + - compatible : "ti,tsc2005" + - reg : SPI device address + - spi-max-frequency : Maximal SPI speed + - interrupts : IRQ specifier + - reset-gpios : GPIO specifier + - vio-supply : Regulator specifier + +Optional properties: + - ti,x-plate-ohms : integer, resistance of the touchscreen's X plates + in ohm (defaults to 280) + - ti,esd-recovery-timeout-ms : integer, if the touchscreen does not respond after + the configured time (in milli seconds), the driver + will reset it. This is disabled by default. + - properties defined in touchscreen.txt + +Example: + +&mcspi1 { + tsc2005@0 { + compatible = "ti,tsc2005"; + spi-max-frequency = <6000000>; + reg = <0>; + + vio-supply = <&vio>; + + reset-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* 104 */ + interrupts-extended = <&gpio4 4 IRQ_TYPE_EDGE_RISING>; /* 100 */ + + touchscreen-fuzz-x = <4>; + touchscreen-fuzz-y = <7>; + touchscreen-fuzz-pressure = <2>; + touchscreen-max-x = <4096>; + touchscreen-max-y = <4096>; + touchscreen-max-pressure = <2048>; + + ti,x-plate-ohms = <280>; + ti,esd-recovery-timeout-ms = <8000>; + }; +} diff --git a/drivers/input/touchscreen/tsc2005.c b/drivers/input/touchscreen/tsc2005.c index d981e49368ad..52380b68ebdf 100644 --- a/drivers/input/touchscreen/tsc2005.c +++ b/drivers/input/touchscreen/tsc2005.c @@ -25,11 +25,15 @@ #include #include #include +#include #include #include #include +#include +#include #include #include +#include /* * The touchscreen interface operates as follows: @@ -100,6 +104,11 @@ TSC2005_CFR2_AVG_7) #define MAX_12BIT 0xfff +#define TSC2005_DEF_X_FUZZ 4 +#define TSC2005_DEF_Y_FUZZ 8 +#define TSC2005_DEF_P_FUZZ 2 +#define TSC2005_DEF_RESISTOR 280 + #define TSC2005_SPI_MAX_SPEED_HZ 10000000 #define TSC2005_PENUP_TIME_MS 40 @@ -143,6 +152,9 @@ struct tsc2005 { bool pen_down; + struct regulator *vio; + + int reset_gpio; void (*set_reset)(bool enable); }; @@ -337,6 +349,14 @@ static void tsc2005_stop_scan(struct tsc2005 *ts) tsc2005_cmd(ts, TSC2005_CMD_STOP); } +static void tsc2005_set_reset(struct tsc2005 *ts, bool enable) +{ + if (ts->reset_gpio >= 0) + gpio_set_value(ts->reset_gpio, enable); + else if (ts->set_reset) + ts->set_reset(enable); +} + /* must be called with ts->mutex held */ static void __tsc2005_disable(struct tsc2005 *ts) { @@ -355,7 +375,7 @@ static void __tsc2005_enable(struct tsc2005 *ts) { tsc2005_start_scan(ts); - if (ts->esd_timeout && ts->set_reset) { + if (ts->esd_timeout && (ts->set_reset || ts->reset_gpio)) { ts->last_valid_interrupt = jiffies; schedule_delayed_work(&ts->esd_work, round_jiffies_relative( @@ -414,9 +434,9 @@ static ssize_t tsc2005_selftest_show(struct device *dev, } /* hardware reset */ - ts->set_reset(false); + tsc2005_set_reset(ts, false); usleep_range(100, 500); /* only 10us required */ - ts->set_reset(true); + tsc2005_set_reset(ts, true); if (!success) goto out; @@ -459,7 +479,7 @@ static umode_t tsc2005_attr_is_visible(struct kobject *kobj, umode_t mode = attr->mode; if (attr == &dev_attr_selftest.attr) { - if (!ts->set_reset) + if (!ts->set_reset && !ts->reset_gpio) mode = 0; } @@ -509,9 +529,9 @@ static void tsc2005_esd_work(struct work_struct *work) tsc2005_update_pen_state(ts, 0, 0, 0); - ts->set_reset(false); + tsc2005_set_reset(ts, false); usleep_range(100, 500); /* only 10us required */ - ts->set_reset(true); + tsc2005_set_reset(ts, true); enable_irq(ts->spi->irq); tsc2005_start_scan(ts); @@ -572,29 +592,47 @@ static void tsc2005_setup_spi_xfer(struct tsc2005 *ts) static int tsc2005_probe(struct spi_device *spi) { const struct tsc2005_platform_data *pdata = dev_get_platdata(&spi->dev); + struct device_node *np = spi->dev.of_node; + struct tsc2005 *ts; struct input_dev *input_dev; - unsigned int max_x, max_y, max_p; - unsigned int fudge_x, fudge_y, fudge_p; + unsigned int max_x = MAX_12BIT; + unsigned int max_y = MAX_12BIT; + unsigned int max_p = MAX_12BIT; + unsigned int fudge_x = TSC2005_DEF_X_FUZZ; + unsigned int fudge_y = TSC2005_DEF_Y_FUZZ; + unsigned int fudge_p = TSC2005_DEF_P_FUZZ; + unsigned int x_plate_ohm = TSC2005_DEF_RESISTOR; + unsigned int esd_timeout; int error; - if (!pdata) { + if (!np && !pdata) { dev_err(&spi->dev, "no platform data\n"); return -ENODEV; } - fudge_x = pdata->ts_x_fudge ? : 4; - fudge_y = pdata->ts_y_fudge ? : 8; - fudge_p = pdata->ts_pressure_fudge ? : 2; - max_x = pdata->ts_x_max ? : MAX_12BIT; - max_y = pdata->ts_y_max ? : MAX_12BIT; - max_p = pdata->ts_pressure_max ? : MAX_12BIT; - if (spi->irq <= 0) { dev_err(&spi->dev, "no irq\n"); return -ENODEV; } + if (pdata) { + fudge_x = pdata->ts_x_fudge; + fudge_y = pdata->ts_y_fudge; + fudge_p = pdata->ts_pressure_fudge; + max_x = pdata->ts_x_max; + max_y = pdata->ts_y_max; + max_p = pdata->ts_pressure_max; + x_plate_ohm = pdata->ts_x_plate_ohm; + esd_timeout = pdata->esd_timeout_ms; + } else { + x_plate_ohm = TSC2005_DEF_RESISTOR; + of_property_read_u32(np, "ti,x-plate-ohms", &x_plate_ohm); + esd_timeout = 0; + of_property_read_u32(np, "ti,esd-recovery-timeout-ms", + &esd_timeout); + } + spi->mode = SPI_MODE_0; spi->bits_per_word = 8; if (!spi->max_speed_hz) @@ -615,9 +653,37 @@ static int tsc2005_probe(struct spi_device *spi) ts->spi = spi; ts->idev = input_dev; - ts->x_plate_ohm = pdata->ts_x_plate_ohm ? : 280; - ts->esd_timeout = pdata->esd_timeout_ms; - ts->set_reset = pdata->set_reset; + ts->x_plate_ohm = x_plate_ohm; + ts->esd_timeout = esd_timeout; + + if (np) { + ts->reset_gpio = of_get_named_gpio(np, "reset-gpios", 0); + if (ts->reset_gpio == -EPROBE_DEFER) + return ts->reset_gpio; + if (ts->reset_gpio < 0) { + dev_err(&spi->dev, "error acquiring reset gpio: %d\n", + ts->reset_gpio); + return ts->reset_gpio; + } + + error = devm_gpio_request_one(&spi->dev, ts->reset_gpio, 0, + "reset-gpios"); + if (error) { + dev_err(&spi->dev, "error requesting reset gpio: %d\n", + error); + return error; + } + + ts->vio = devm_regulator_get(&spi->dev, "vio"); + if (IS_ERR(ts->vio)) { + error = PTR_ERR(ts->vio); + dev_err(&spi->dev, "vio regulator missing (%d)", error); + return error; + } + } else { + ts->reset_gpio = -1; + ts->set_reset = pdata->set_reset; + } mutex_init(&ts->mutex); @@ -642,6 +708,9 @@ static int tsc2005_probe(struct spi_device *spi) input_set_abs_params(input_dev, ABS_Y, 0, max_y, fudge_y, 0); input_set_abs_params(input_dev, ABS_PRESSURE, 0, max_p, fudge_p, 0); + if (np) + touchscreen_parse_of_params(input_dev); + input_dev->open = tsc2005_open; input_dev->close = tsc2005_close; @@ -659,12 +728,19 @@ static int tsc2005_probe(struct spi_device *spi) return error; } + /* enable regulator for DT */ + if (ts->vio) { + error = regulator_enable(ts->vio); + if (error) + return error; + } + spi_set_drvdata(spi, ts); error = sysfs_create_group(&spi->dev.kobj, &tsc2005_attr_group); if (error) { dev_err(&spi->dev, "Failed to create sysfs attributes, err: %d\n", error); - return error; + goto disable_regulator; } error = input_register_device(ts->idev); @@ -679,13 +755,21 @@ static int tsc2005_probe(struct spi_device *spi) err_remove_sysfs: sysfs_remove_group(&spi->dev.kobj, &tsc2005_attr_group); +disable_regulator: + if (ts->vio) + regulator_disable(ts->vio); return error; } static int tsc2005_remove(struct spi_device *spi) { + struct tsc2005 *ts = spi_get_drvdata(spi); + sysfs_remove_group(&spi->dev.kobj, &tsc2005_attr_group); + if (ts->vio) + regulator_disable(ts->vio); + return 0; }