From: Isaev Ruslan Date: Wed, 28 Feb 2024 07:53:54 +0000 (+0300) Subject: qualcommax: ipq60xx: add yuncore fap650 support X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=9ef4f7f9194c68a587336d7661c4a5124a5e86fd;p=openwrt%2Fstaging%2Fxback.git qualcommax: ipq60xx: add yuncore fap650 support This commit adds support for the Yuncore FAP650 device. Specifications: - Qualcomm IPQ6018+QCA8075+QCN5022+QCN5052 - 512 MB of RAM (DDR3) - 8 MB of serial flash (SPI NOR) - 128 MB of parallel flash (NAND) - 2x2 2.4 GHz WiFi (IPQ6010) - 2x2 5 GHz WiFi (IPQ6010) - 2x 2dBi 2.4G MIMO antenna - 2x 3dBi 5.8G MIMO antenna - 5x 1 Gbps Ethernet (QCA8075) - POE: 48V (IEEE 802.3af) - power: 12V (~1.5A) - 1x passthru port (rj45 - rj45) - 1x cisco rj45 console port - size: 160mm*86mm*29mm BACKUP YOUR STOCK FIRMWARE: ``` export device=fap650 mkdir -p /tmp/fw_dump_$device cd /tmp/fw_dump_$device dmesg > dmesg_$device.log dtc -I fs /sys/firmware/devicetree/base > $device.dts cat /proc/device-tree/model > model cat /proc/mtd > proc_mtd while read p; do mtd_dev=$(echo $p | cut -d: -f1) echo $mtd_dev dd if=/dev/$mtd_dev of=$mtd_dev done < proc_mtd md5sum * > md5sum.log tar -cvzf ../$device.tar.gz . export sum=$(md5sum /tmp/$device.tar.gz | cut -d' ' -f1) mv ../$device.tar.gz /tmp/${device}_${sum}.tar.gz echo fw backup saved to: /tmp/${device}_${sum}.tar.gz ``` Upload your backup via tftp to the safe place. INSTALLATION: 1. stock firmware web ui Rename factory.bin fw image file to factory.ubin. Flash this image like ordinary stock fw upgrade. 2. stock firmware telnet method Enter telnet cli (login: root, password: 476t*_f0%g09y) and upload factory.bin fw image and rename it to factory.ubin `cd /tmp && wget /factory.ubin` `sysupgrade factory.ubin 3. initramfs method Put imitramfs image to your TFTP server and rename it for example to fap650.initram Enable serial console and enter to the u-boot cli. Exec these commands: `tftpboot :fap650.initram` `dhcp` When downloading is finished: `bootm` After booting the device, you need to upload to the device factory.ubi fw image. ``` cd /tmp && wget /factory.ubi` export rootfs=$(cat /proc/mtd | grep rootfs | cut -d: -f1) export rootfs_1=$(cat /proc/mtd | grep rootfs_1 | cut -d: -f1) ubiformat /dev/${rootfs} -y -f factory.ubi ubiformat /dev/${rootfs_1} -y -f factory.ubi reboot ``` 4. u-boot factory.ubi image method Put factory.ubi to your TFTP server Enter u-boot cli and exec these commands: `tftpboot :factory.ubi` `dhcp` After downloading is finished: `flash rootfs` `flash rootfs_1` `reset` STOCK FIRMWARE RECOVERY: Boot initramfs image. Upload your rootfs mtd partition to the device using scp or download it from the device using wget. Enter device ssh cli and exec: ``` cd /tmp && wget /rootfs_mtd` export rootfs=$(cat /proc/mtd | grep rootfs | cut -d: -f1) export rootfs_1=$(cat /proc/mtd | grep rootfs_1 | cut -d: -f1) ubiformat /dev/${rootfs} -y -f /tmp/rootfs_mtd ubiformat /dev/${rootfs_1} -y -f /tmp/rootfs_mtd reboot ``` Signed-off-by: Isaev Ruslan --- diff --git a/package/boot/uboot-envtools/files/qualcommax_ipq60xx b/package/boot/uboot-envtools/files/qualcommax_ipq60xx index 33cb94f99d..749b053aab 100644 --- a/package/boot/uboot-envtools/files/qualcommax_ipq60xx +++ b/package/boot/uboot-envtools/files/qualcommax_ipq60xx @@ -19,6 +19,11 @@ netgear,wax214) [ -n "$idx" ] && \ ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x40000" "0x20000" "2" ;; +yuncore,fap650) + idx="$(find_mtd_index 0:appsblenv)" + [ -n "$idx" ] && \ + ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x10000" "0x10000" + ;; esac config_load ubootenv diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile index a34e368a5d..3a339267ab 100644 --- a/package/firmware/ipq-wifi/Makefile +++ b/package/firmware/ipq-wifi/Makefile @@ -6,10 +6,9 @@ PKG_RELEASE:=2 PKG_SOURCE_PROTO:=git PKG_SOURCE_URL=$(PROJECT_GIT)/project/firmware/qca-wireless.git -PKG_SOURCE_DATE:=2024-03-04 -PKG_SOURCE_VERSION:=38c02ae4302f9cb73f6914574239fe84799caa84 -PKG_MIRROR_HASH:=1e84f576d4161ea932b45a651abebdc05ff3c261ef25fc13d3d68cf9b624abb3 - +PKG_SOURCE_DATE:=2024-03-20 +PKG_SOURCE_VERSION:=87717baa8a7c922942f4202a0ec3de3cb5643941 +PKG_MIRROR_HASH:=75f05f922780b55c0069c4ee9725f2b1aa857f3bc841bec71a44e997ece9cea15 PKG_FLAGS:=nonshared include $(INCLUDE_DIR)/package.mk @@ -52,6 +51,7 @@ ALLWIFIBOARDS:= \ xiaomi_ax9000 \ yyets_le1 \ yuncore_ax880 \ + yuncore_fap650 \ zte_mf269 \ zte_mf287 \ zte_mf287plus \ @@ -169,6 +169,7 @@ $(eval $(call generate-ipq-wifi-package,xiaomi_ax3600,Xiaomi AX3600)) $(eval $(call generate-ipq-wifi-package,xiaomi_ax9000,Xiaomi AX9000)) $(eval $(call generate-ipq-wifi-package,yyets_le1,YYeTs LE1)) $(eval $(call generate-ipq-wifi-package,yuncore_ax880,Yuncore AX880)) +$(eval $(call generate-ipq-wifi-package,yuncore_fap650,Yuncore FAP650)) $(eval $(call generate-ipq-wifi-package,zte_mf269,ZTE MF269)) $(eval $(call generate-ipq-wifi-package,zte_mf287,ZTE MF287)) $(eval $(call generate-ipq-wifi-package,zte_mf287plus,ZTE MF287Plus)) diff --git a/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq6018-512m.dtsi b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq6018-512m.dtsi new file mode 100644 index 0000000000..d46a852404 --- /dev/null +++ b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq6018-512m.dtsi @@ -0,0 +1,23 @@ +// SPDX-License-Identifier: GPL-2.0-only + +#include "ipq6018.dtsi" + +&rpm_msg_ram { + reg = <0x0 0x00060000 0x0 0x6000>; + no-map; +}; + +&tz { + reg = <0x0 0x4a600000 0x0 0x00400000>; + no-map; +}; + +&smem_region { + reg = <0x0 0x4aa00000 0x0 0x00100000>; + no-map; +}; + +&q6_region { + reg = <0x0 0x4ab00000 0x0 0x03700000>; + no-map; +}; diff --git a/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq6018-fap650.dts b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq6018-fap650.dts new file mode 100644 index 0000000000..e9ebcc9063 --- /dev/null +++ b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq6018-fap650.dts @@ -0,0 +1,365 @@ +// SPDX-License-Identifier: MIT, GPL-2.0 or later +/* Copyright (c) 2023, Ruslan Isaev */ + +/dts-v1/; + +#include "ipq6018-512m.dtsi" +#include "ipq6018-cp-cpu.dtsi" +#include "ipq6018-ess.dtsi" +#include +#include +#include + +/ { + model = "Yuncore FAP650"; + compatible = "yuncore,fap650", "qcom,ipq6018"; + + aliases { + ethernet0 = &dp5; + ethernet1 = &dp4; + ethernet2 = &dp3; + ethernet3 = &dp2; + ethernet4 = &dp1; + label-mac-device = &dp5; + serial0 = &blsp1_uart3; + led-boot = &led_system; + led-failsafe = &led_system; + led-running = &led_system; + led-upgrade = &led_system; + }; + + chosen { + stdout-path = "serial0:115200n8"; + bootargs-append = " root=/dev/ubiblock0_1"; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&tlmm 19 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_system: system { + color = ; + function = LED_FUNCTION_STATUS; + gpios = <&tlmm 32 GPIO_ACTIVE_HIGH>; + }; + + wlan2g { + color = ; + function = LED_FUNCTION_WLAN_2GHZ; + gpios = <&tlmm 37 GPIO_ACTIVE_HIGH>; + }; + + wlan5g { + color = ; + function = LED_FUNCTION_WLAN_5GHZ; + gpios = <&tlmm 35 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&blsp1_uart3 { + pinctrl-0 = <&serial_3_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&tlmm { + mdio_pins: mdio-pins { + mdc { + pins = "gpio64"; + function = "mdc"; + drive-strength = <8>; + bias-pull-up; + }; + + mdio { + pins = "gpio65"; + function = "mdio"; + drive-strength = <8>; + bias-pull-up; + }; + }; +}; + +&mdio { + status = "okay"; + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + reset-gpios = <&tlmm 75 GPIO_ACTIVE_LOW>; + reset-delay-us = <10000>; + reset-post-delay-us = <50000>; + + ethernet-phy-package@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "qcom,qca8075-package"; + reg = <0>; + + qcom,package-mode = "psgmii"; + + qca8075_0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + }; + + qca8075_1: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; + + qca8075_2: ethernet-phy@2 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <2>; + }; + + qca8075_3: ethernet-phy@3 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <3>; + }; + + qca8075_4: ethernet-phy@4 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <4>; + }; + }; +}; + +&switch { + status = "okay"; + switch_lan_bmp = <(ESS_PORT1|ESS_PORT2|ESS_PORT3|ESS_PORT4)>; /* lan port bitmap */ + switch_wan_bmp = ; /* wan port bitmap */ + switch_mac_mode = ; /* mac mode for uniphy instance0*/ + + qcom,port_phyinfo { + port@1 { + port_id = <1>; + phy_address = <0>; + }; + + port@2 { + port_id = <2>; + phy_address = <1>; + }; + + port@3 { + port_id = <3>; + phy_address = <2>; + }; + + port@4 { + port_id = <4>; + phy_address = <3>; + }; + + port@5 { + port_id = <5>; + phy_address = <4>; + }; + }; +}; + +&usb2 { + status = "okay"; +}; + +&usb3 { + status = "okay"; +}; + +&edma { + status = "okay"; +}; + +&dp1 { + status = "okay"; + phy-handle = <&qca8075_0>; + label = "lan1"; +}; + +&dp2 { + status = "okay"; + phy-handle = <&qca8075_1>; + label = "lan2"; +}; + +&dp3 { + status = "okay"; + phy-handle = <&qca8075_2>; + label = "lan3"; +}; + +&dp4 { + status = "okay"; + phy-handle = <&qca8075_3>; + label = "lan4"; +}; + +&dp5 { + status = "okay"; + phy-handle = <&qca8075_4>; + phy-mode = "psgmii"; + label = "wan"; +}; + +&qpic_bam { + status = "okay"; +}; + +&blsp1_spi1 { + status = "okay"; + + flash@0 { + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + compatible = "jedec,spi-nor"; + spi-max-frequency = <50000000>; + + partitions { + compatible = "fixed-partitions"; + + partition@0 { + reg = <0x00000000 0x000c0000>; + label = "0:sbl1"; + }; + + partition@c0000 { + reg = <0x000c0000 0x00010000>; + label = "0:mibib"; + }; + + partition@d0000 { + reg = <0x000d0000 0x00020000>; + label = "0:bootconfig"; + }; + + partition@f0000 { + reg = <0x000f0000 0x00020000>; + label = "0:bootconfig1"; + }; + + partition@110000 { + reg = <0x00110000 0x001a0000>; + label = "0:qsee"; + }; + + partition@2b0000 { + reg = <0x002b0000 0x001a0000>; + label = "0:qsee_1"; + }; + + partition@450000 { + reg = <0x00450000 0x00010000>; + label = "0:devcfg"; + }; + + partition@460000 { + reg = <0x00460000 0x00010000>; + label = "0:devcfg_1"; + }; + + partition@470000 { + reg = <0x00470000 0x00040000>; + label = "0:rpm"; + }; + + partition@4b0000 { + reg = <0x004b0000 0x00040000>; + label = "0:rpm_1"; + }; + + partition@4f0000 { + reg = <0x004f0000 0x00010000>; + label = "0:cdt"; + }; + + partition@500000 { + reg = <0x00500000 0x00010000>; + label = "0:cdt_1"; + }; + + partition@510000 { + reg = <0x00510000 0x00010000>; + label = "0:appsblenv"; + }; + + partition@520000 { + reg = <0x00520000 0x000a0000>; + label = "0:appsbl"; + }; + + partition@5c0000 { + reg = <0x005c0000 0x000a0000>; + label = "0:appsbl_1"; + }; + + partition@660000 { + reg = <0x00660000 0x00040000>; + label = "0:art"; + }; + }; + }; +}; + +&qpic_nand { + status = "okay"; + + nand@0 { + reg = <0>; + + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + nand-bus-width = <8>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "rootfs"; + reg = <0x00000000 0x03c00000>; + }; + + partition@3c00000 { + label = "rootfs_1"; + reg = <0x03c00000 0x03c00000>; + }; + }; + }; +}; + +&wifi { + qcom,ath11k-calibration-variant = "Yuncore-FAP650"; + qcom,ath11k-fw-memory-mode = <1>; + status = "okay"; +}; + +&qusb_phy_0 { + status = "okay"; +}; + +&qusb_phy_1 { + status = "okay"; +}; + +&ssphy_0 { + status = "okay"; +}; + +&usb3 { + status = "okay"; +}; + +&usb2 { + status = "okay"; +}; diff --git a/target/linux/qualcommax/image/ipq60xx.mk b/target/linux/qualcommax/image/ipq60xx.mk index a7851e3dc5..79822ceb01 100644 --- a/target/linux/qualcommax/image/ipq60xx.mk +++ b/target/linux/qualcommax/image/ipq60xx.mk @@ -23,3 +23,19 @@ define Device/netgear_wax214 DEVICE_PACKAGES := ipq-wifi-netgear_wax214 endef TARGET_DEVICES += netgear_wax214 + +define Device/yuncore_fap650 + $(call Device/FitImage) + $(call Device/UbiFit) + DEVICE_VENDOR := Yuncore + DEVICE_MODEL := FAP650 + BLOCKSIZE := 128k + PAGESIZE := 2048 + DEVICE_DTS_CONFIG := config@cp03-c1 + SOC := ipq6018 + DEVICE_PACKAGES := ipq-wifi-yuncore_fap650 + IMAGES := factory.ubi factory.ubin sysupgrade.bin + IMAGE/factory.ubin := append-ubi | qsdk-ipq-factory-nand +endef +TARGET_DEVICES += yuncore_fap650 + diff --git a/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/01_leds b/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/01_leds new file mode 100644 index 0000000000..189822157f --- /dev/null +++ b/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/01_leds @@ -0,0 +1,18 @@ + +. /lib/functions/leds.sh +. /lib/functions/uci-defaults.sh + +board_config_update + +board=$(board_name) + +case "$board" in +yuncore,fap650) + ucidef_set_led_netdev "wlan5ghz" "WLAN 5GHz LED" "blue:wlan-5ghz" "wlan0" "tx rx" + ucidef_set_led_netdev "wlan2ghz" "WLAN 2.4GHz LED" "green:wlan-2ghz" "wlan1" "tx rx" + ;; +esac + +board_config_flush + +exit 0 diff --git a/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/02_network b/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/02_network index aaa2522c92..f5fd35cf44 100644 --- a/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/02_network +++ b/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/02_network @@ -17,6 +17,9 @@ ipq60xx_setup_interfaces() netgear,wax214) ucidef_set_interfaces_lan_wan "lan" ;; + yuncore,fap650) + ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan" + ;; *) echo "Unsupported hardware. Network interfaces not initialized" ;; diff --git a/target/linux/qualcommax/ipq60xx/base-files/etc/hotplug.d/firmware/11-ath11-caldata b/target/linux/qualcommax/ipq60xx/base-files/etc/hotplug.d/firmware/11-ath11-caldata index 89d4c265ab..23a3da0b4b 100644 --- a/target/linux/qualcommax/ipq60xx/base-files/etc/hotplug.d/firmware/11-ath11-caldata +++ b/target/linux/qualcommax/ipq60xx/base-files/etc/hotplug.d/firmware/11-ath11-caldata @@ -15,6 +15,9 @@ case "$FIRMWARE" in netgear,wax214) caldata_extract "0:art" 0x1000 0x10000 ;; + yuncore,fap650) + caldata_extract "0:art" 0x1000 0x20000 + ;; esac ;; *) diff --git a/target/linux/qualcommax/ipq60xx/base-files/etc/init.d/bootcount b/target/linux/qualcommax/ipq60xx/base-files/etc/init.d/bootcount new file mode 100755 index 0000000000..6347976372 --- /dev/null +++ b/target/linux/qualcommax/ipq60xx/base-files/etc/init.d/bootcount @@ -0,0 +1,14 @@ +#!/bin/sh /etc/rc.common + +START=99 + +. /lib/functions.sh + +boot() { + case $(board_name) in + yuncore,fap650) + fw_setenv owrt_bootcount 0 + ;; + esac +} + diff --git a/target/linux/qualcommax/ipq60xx/base-files/lib/upgrade/platform.sh b/target/linux/qualcommax/ipq60xx/base-files/lib/upgrade/platform.sh index 4008cb0224..a8e4872cdd 100644 --- a/target/linux/qualcommax/ipq60xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/qualcommax/ipq60xx/base-files/lib/upgrade/platform.sh @@ -8,11 +8,46 @@ platform_check_image() { return 0; } + +yuncore_fap650_env_setup() { + local ubifile=$(board_name) + local active=$(fw_printenv -n owrt_slotactive) + [ -z "$active" ] && active=$(hexdump -s 0x94 -n 4 -e '4 "%d"' /dev/mtd$(find_mtd_index 0:bootconfig)) + cat > /tmp/env_tmp << EOF +owrt_slotactive=${active} +owrt_bootcount=0 +bootfile=${ubifile}.ubi +owrt_bootcountcheck=if test \$owrt_bootcount > 4; then run owrt_tftprecover; fi; if test \$owrt_bootcount = 3; then run owrt_slotswap; else echo bootcountcheck successfull; fi +owrt_bootinc=if test \$owrt_bootcount < 5; then echo save env part; setexpr owrt_bootcount \${owrt_bootcount} + 1 && saveenv; else echo save env skipped; fi; echo current bootcount: \$owrt_bootcount +bootcmd=run owrt_bootinc && run owrt_bootcountcheck && run owrt_slotselect && run owrt_bootlinux +owrt_bootlinux=echo booting linux... && ubi part fs && ubi read 0x44000000 kernel && bootm; reset +owrt_setslot0=setenv bootargs console=ttyMSM0,115200n8 ubi.mtd=rootfs root=mtd:rootfs rootfstype=squashfs rootwait swiotlb=1 && setenv mtdparts mtdparts=nand0:0x3c00000@0(fs) +owrt_setslot1=setenv bootargs console=ttyMSM0,115200n8 ubi.mtd=rootfs_1 root=mtd:rootfs rootfstype=squashfs rootwait swiotlb=1 && setenv mtdparts mtdparts=nand0:0x3c00000@0x3c00000(fs) +owrt_slotswap=setexpr owrt_slotactive 1 - \${owrt_slotactive} && saveenv && echo slot swapped. new active slot: \$owrt_slotactive +owrt_slotselect=setenv mtdids nand0=nand0,nand1=spi0.0; if test \$owrt_slotactive = 0; then run owrt_setslot0; else run owrt_setslot1; fi +owrt_tftprecover=echo trying to recover firmware with tftp... && sleep 10 && dhcp && flash rootfs && flash rootfs_1 && setenv owrt_bootcount 0 && setenv owrt_slotactive 0 && saveenv && reset +owrt_env_ver=7 +EOF + fw_setenv --script /tmp/env_tmp +} + platform_do_upgrade() { case "$(board_name)" in netgear,wax214) nand_do_upgrade "$1" ;; + yuncore,fap650) + [ "$(fw_printenv -n owrt_env_ver 2>/dev/null)" != "7" ] && yuncore_fap650_env_setup + local active="$(fw_printenv -n owrt_slotactive 2>/dev/null)" + if [ "$active" = "1" ]; then + CI_UBIPART="rootfs" + else + CI_UBIPART="rootfs_1" + fi + fw_setenv owrt_bootcount 0 + fw_setenv owrt_slotactive $((1 - active)) + nand_do_upgrade "$1" + ;; *) default_do_upgrade "$1" ;;