From: Dirk Buchwalder Date: Fri, 17 May 2024 15:33:00 +0000 (+0200) Subject: mediatek: filogic: add support for TP-LINK RE6000XD X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=9e49593ff7f9860fc7901c17977ce2ec976adb4c;p=openwrt%2Fstaging%2Fthess.git mediatek: filogic: add support for TP-LINK RE6000XD This commit adds support for TP-LINK RE6000XD. The device is quite similar to the Mercusys MR90X V1, except only 3 LAN ports and more LEDs. So thanks to csharper2005 for doing all the groundwork. Device specification -------------------- SoC Type: MediaTek MT7986BLA, Cortex-A53, 64-bit RAM: MediaTek MT7986BLA (512MB) Flash: SPI NAND GigaDevice (128 MB) Ethernet: MediaTek MT7531AE + 2.5GbE MaxLinear GPY211C0VC (SLNW8) Ethernet: 1x2.5Gbe (LAN3 2.5Gbps), 2xGbE (LAN 1Gbps, LAN1, LAN2) WLAN 2g: MediaTek MT7975N, b/g/n/ax, MIMO 4x4 WLAN 5g: MediaTek MT7975P(N), a/n/ac/ax, MIMO 4x4 LEDs: 8 LEDs, 1 status blue, 2x WIFI blue, 2x signal blue/red, 3 LAN blue gpio-controlled Button: 2 (Reset, WPS) USB ports: No Power: 12 VDC, 2 A Connector: Barrel Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, ubi0 partition contain "seconduboot" (also U-Boot 2022.01-rc4) Serial console (UART), unpopulated --------------------- V +-------+-------+-------+-------+ | +3.3V | GND | TX | RX | +---+---+-------+-------+-------+ | +--- Don't connect Disassemble: rm the 2 screws at the bottom and the one at the backside. un-clip the case starting at the edge above the LEDs. Installation (UART) ------------------- 1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2 2. Attach UART, switch on the router and interrupt the boot process by pressing 'Ctrl-C' 3. Load and run OpenWrt initramfs image: tftpboot openwrt-mediatek-filogic-tplink_re6000xd-initramfs-kernel.bin bootm 4. Run 'sysupgrade -n' with the sysupgrade OpenWrt image Notice: while I was successfull at activating ssh (as described here: https://www.lisenet.com/2023/gaining-ssh-access-to-tp-link-re200-wi-fi-range-extender/) Unfortunately I haven't found the correct root password. Looks like they are using a static password (md5crypt, salt + 21 characters) that is not the web interface admin password. The TP-LINK RE900XD looks like the very same device, according to the pictures and the firmware. But I haven't checked if the OpenWrt firmware works as well on that device. The second ubi partition (ubi1) is empty and there is no known dual-partition mechanism, neither in u-boot nor in the stock firmware. Signed-off-by: Dirk Buchwalder --- diff --git a/package/boot/uboot-envtools/files/mediatek_filogic b/package/boot/uboot-envtools/files/mediatek_filogic index c93fa2499b..0e30c489c9 100644 --- a/package/boot/uboot-envtools/files/mediatek_filogic +++ b/package/boot/uboot-envtools/files/mediatek_filogic @@ -102,7 +102,8 @@ glinet,gl-mt3000) ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x80000" "0x20000" ;; mercusys,mr90x-v1|\ -routerich,ax3000) +routerich,ax3000|\ +tplink,re6000xd) local envdev=/dev/mtd$(find_mtd_index "u-boot-env") ubootenv_add_uci_config "$envdev" "0x0" "0x20000" "0x20000" "1" ;; diff --git a/target/linux/mediatek/dts/mt7986b-tplink-re6000xd.dts b/target/linux/mediatek/dts/mt7986b-tplink-re6000xd.dts new file mode 100644 index 0000000000..44a5e21e7c --- /dev/null +++ b/target/linux/mediatek/dts/mt7986b-tplink-re6000xd.dts @@ -0,0 +1,298 @@ +// SPDX-License-Identifier: (GL-2.0 OR MIT) + +/dts-v1/; +#include +#include +#include + +#include "mt7986b.dtsi" + +/ { + compatible = "tplink,re6000xd", "mediatek,mt7986b"; + model = "TP-Link RE6000XD"; + + aliases { + serial0 = &uart0; + + led-boot = &led_status_blue; + led-failsafe = &led_status_blue; + led-running = &led_status_blue; + led-upgrade = &led_status_blue; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory { + reg = <0 0x40000000 0 0x20000000>; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&pio 7 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&pio 14 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_status_blue: power { + gpios = <&pio 15 GPIO_ACTIVE_LOW>; + color = ; + function = LED_FUNCTION_STATUS; + panic-indicator; + function-enumerator = <0>; + }; + wlan_2g { + gpios = <&pio 11 GPIO_ACTIVE_HIGH>; + color = ; + function = LED_FUNCTION_WLAN_2GHZ; + linux,default-trigger = "phy0tpt"; + }; + wlan_5g { + gpios = <&pio 12 GPIO_ACTIVE_LOW>; + color = ; + function = LED_FUNCTION_WLAN_5GHZ; + linux,default-trigger = "phy1tpt"; + }; + signal_blue { + gpios = <&pio 9 GPIO_ACTIVE_LOW>; + color = ; + function = LED_FUNCTION_STATUS; + function-enumerator = <1>; + }; + signal_red { + gpios = <&pio 19 GPIO_ACTIVE_LOW>; + color = ; + function = LED_FUNCTION_STATUS; + function-enumerator = <2>; + }; + lan1 { + gpios = <&pio 16 GPIO_ACTIVE_HIGH>; + color = ; + function = LED_FUNCTION_LAN; + function-enumerator = <0>; + }; + lan2 { + gpios = <&pio 10 GPIO_ACTIVE_LOW>; + color = ; + function = LED_FUNCTION_LAN; + function-enumerator = <1>; + }; + lan3 { + gpios = <&pio 18 GPIO_ACTIVE_LOW>; + color = ; + function = LED_FUNCTION_LAN; + function-enumerator = <2>; + }; + }; +}; + +&crypto { + status = "okay"; +}; + +ð { + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + + gmac1: mac@1 { + compatible = "mediatek,eth-mac"; + reg = <1>; + phy-handle = <&phy6>; + phy-mode = "2500base-x"; + }; + + mdio: mdio-bus { + #address-cells = <1>; + #size-cells = <0>; + }; +}; + +&mdio { + #address-cells = <1>; + #size-cells = <0>; + + reset-gpios = <&pio 6 GPIO_ACTIVE_LOW>; + reset-delay-us = <1500000>; + reset-post-delay-us = <1000000>; + + /* LAN3 2.5Gbps phy + MaxLinear GPY211C0VC (SLNW8) */ + phy6: phy@6 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <6>; + }; + + switch: switch@1f { + compatible = "mediatek,mt7531"; + reg = <31>; + reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>; + }; +}; + +&switch { + ports { + #address-cells = <1>; + #size-cells = <0>; + /* reorder LAN1 and LAN2 port to match the port order of the case + LAN1 - LAN2 - LAN3 (top to bottom of the case, no silkscreen) + */ + /* LAN2 port */ + port@1 { + reg = <1>; + label = "lan2"; + }; + + /* LAN1 port */ + port@2 { + reg = <2>; + label = "lan1"; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; +}; + +&pio { + spi_flash_pins: spi-flash-pins-33-to-38 { + mux { + function = "spi"; + groups = "spi0", "spi0_wp_hold"; + }; + conf-pu { + pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP"; + drive-strength = <8>; + mediatek,pull-up-adv = <0>; /* bias-disable */ + }; + conf-pd { + pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO"; + drive-strength = <8>; + mediatek,pull-down-adv = <0>; /* bias-disable */ + }; + }; + + wf_2g_5g_pins: wf_2g_5g-pins { + mux { + function = "wifi"; + groups = "wf_2g", "wf_5g"; + }; + conf { + pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4", + "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6", + "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10", + "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1", + "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0", + "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8", + "WF1_TOP_CLK", "WF1_TOP_DATA"; + drive-strength = <4>; + }; + }; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi_flash_pins>; + status = "okay"; + + spi_nand_flash: flash@0 { + compatible = "spi-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + + spi-max-frequency = <20000000>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + + partitions: partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "boot"; + reg = <0x0 0x200000>; + read-only; + }; + + partition@200000 { + label = "u-boot-env"; + reg = <0x200000 0x100000>; + }; + + partition@300000 { + label = "ubi0"; + reg = <0x300000 0x3200000>; + }; + + partition@3500000 { + label = "ubi1"; + reg = <0x3500000 0x3200000>; + read-only; + }; + + partition@6700000 { + label = "userconfig"; + reg = <0x6700000 0x800000>; + read-only; + }; + + partition@6f00000 { + label = "tp_data"; + reg = <0x6f00000 0x400000>; + read-only; + }; + }; + }; +}; + +&trng { + status = "okay"; +}; + +&uart0 { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +&wifi { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&wf_2g_5g_pins>; +}; diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds index ca462d2005..99519cca7e 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds @@ -96,6 +96,11 @@ wavlink,wl-wn586x3) ucidef_set_led_netdev "lan-2" "lan-2" "blue:lan-2" "lan2" "link tx rx" ucidef_set_led_netdev "wan" "wan" "blue:wan" "eth1" "link tx rx" ;; +tplink,re6000xd) + ucidef_set_led_netdev "lan-1" "lan-1" "blue:lan-0" "lan1" "link tx rx" + ucidef_set_led_netdev "lan-2" "lan-2" "blue:lan-1" "lan2" "link tx rx" + ucidef_set_led_netdev "eth1" "lan-3" "blue:lan-2" "eth1" "link tx rx" + ;; xiaomi,mi-router-wr30u-stock|\ xiaomi,mi-router-wr30u-ubootmod) ucidef_set_led_netdev "wan" "wan" "blue:wan" "wan" "link tx rx" diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network index 70b076dc9f..1a210810bc 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network @@ -100,6 +100,9 @@ mediatek_setup_interfaces() wavlink,wl-wn586x3) ucidef_set_interfaces_lan_wan "lan1 lan2" eth1 ;; + tplink,re6000xd) + ucidef_set_interface_lan "lan1 lan2 eth1" + ;; xiaomi,mi-router-ax3000t|\ xiaomi,mi-router-ax3000t-ubootmod|\ xiaomi,mi-router-wr30u-stock|\ @@ -145,7 +148,8 @@ mediatek_setup_macs() lan_mac=$(macaddr_add "$wan_mac" 1) label_mac=$wan_mac ;; - mercusys,mr90x-v1) + mercusys,mr90x-v1|\ + tplink,re6000xd) label_mac=$(get_mac_binary "/tmp/tp_data/default-mac" 0) lan_mac=$label_mac ;; diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/firmware/11-mt76-caldata b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/firmware/11-mt76-caldata index e0d1d93207..c6d9916b52 100644 --- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/firmware/11-mt76-caldata +++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/firmware/11-mt76-caldata @@ -41,7 +41,8 @@ case "$FIRMWARE" in ;; "mediatek/mt7986_eeprom_mt7975_dual.bin") case "$board" in - mercusys,mr90x-v1) + mercusys,mr90x-v1|\ + tplink,re6000xd) ln -sf /tmp/tp_data/MT7986_EEPROM.bin \ /lib/firmware/$FIRMWARE ;; diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac index 334d221e21..942facee87 100644 --- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac +++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac @@ -109,7 +109,8 @@ case "$board" in jdcloud,re-cp-03) [ "$PHYNBR" = "1" ] && mmc_get_mac_binary factory 0xa > /sys${DEVPATH}/macaddress ;; - mercusys,mr90x-v1) + mercusys,mr90x-v1|\ + tplink,re6000xd) addr=$(get_mac_binary "/tmp/tp_data/default-mac" 0) [ "$PHYNBR" = "0" ] && echo "$addr" > /sys${DEVPATH}/macaddress [ "$PHYNBR" = "1" ] && macaddr_add $addr -1 > /sys${DEVPATH}/macaddress diff --git a/target/linux/mediatek/filogic/base-files/lib/preinit/09_mount_cfg_part b/target/linux/mediatek/filogic/base-files/lib/preinit/09_mount_cfg_part index 819df40d08..11e3b598af 100644 --- a/target/linux/mediatek/filogic/base-files/lib/preinit/09_mount_cfg_part +++ b/target/linux/mediatek/filogic/base-files/lib/preinit/09_mount_cfg_part @@ -12,7 +12,8 @@ mount_ubi_part() { preinit_mount_cfg_part() { case $(board_name) in - mercusys,mr90x-v1) + mercusys,mr90x-v1|\ + tplink,re6000xd) mount_ubi_part "tp_data" ;; *) diff --git a/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh b/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh index 2fe48b0ccf..fefca2327b 100644 --- a/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh +++ b/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh @@ -17,7 +17,8 @@ preinit_set_mac_address() { ip link set dev eth0 address "$addr" ip link set dev eth1 address "$addr" ;; - mercusys,mr90x-v1) + mercusys,mr90x-v1|\ + tplink,re6000xd) addr=$(get_mac_binary "/tmp/tp_data/default-mac" 0) ip link set dev eth1 address "$(macaddr_add $addr 1)" ;; diff --git a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh index 7e105b1089..800e6bc5de 100755 --- a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh +++ b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh @@ -142,7 +142,8 @@ platform_do_upgrade() { CI_KERNPART="fit" nand_do_upgrade "$1" ;; - mercusys,mr90x-v1) + mercusys,mr90x-v1|\ + tplink,re6000xd) CI_UBIPART="ubi0" nand_do_upgrade "$1" ;; diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk index 4db0cf2372..94b3098b3d 100644 --- a/target/linux/mediatek/image/filogic.mk +++ b/target/linux/mediatek/image/filogic.mk @@ -1085,6 +1085,20 @@ define Device/ruijie_rg-x60-pro endef TARGET_DEVICES += ruijie_rg-x60-pro +define Device/tplink_re6000xd + DEVICE_VENDOR := TP-Link + DEVICE_MODEL := RE6000XD + DEVICE_DTS := mt7986b-tplink-re6000xd + DEVICE_DTS_DIR := ../dts + DEVICE_PACKAGES := kmod-mt7915e kmod-mt7986-firmware mt7986-wo-firmware + UBINIZE_OPTS := -E 5 + BLOCKSIZE := 128k + PAGESIZE := 2048 + IMAGE_SIZE := 51200k + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata +endef +TARGET_DEVICES += tplink_re6000xd + define Device/tplink_tl-xdr-common DEVICE_VENDOR := TP-Link DEVICE_DTS_DIR := ../dts