From: Piotr Dymacz Date: Thu, 2 Jul 2020 05:03:33 +0000 (+0200) Subject: ath79: add support for ALFA Network R36A X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=9bcf98ed85fc5f9eca6e7f10cce8d6bf1b23914d;p=openwrt%2Fstaging%2Fneocturne.git ath79: add support for ALFA Network R36A ALFA Network R36A is a successor of the previous model, the R36 (Ralink RT3050F based). New version is based on Qualcomm/Atheros QCA9531 v2, FCC ID: 2AB879531. Support for this device was first introduced in af8f0629df (ar71xx target). When updating from previous release (and/or ar71xx target), user should only adjust the WAN LED trigger type (netdev in ar71xx, switch port in ath79). Specifications: - Qualcomm/Atheros QCA9531 v2 - 650/400/200 MHz (CPU/DDR/AHB) - 128 MB (R36AH/-U2) or 64 MB (R36A) of RAM (DDR2) - 16 MB of flash (SPI NOR) - 2x 10/100 Mbps Ethernet - Passive PoE input support (12~36 V) in RJ45 near DC jack - 2T2R 2.4 GHz Wi-Fi with Qorvo RFFM8228P FEM - 2x IPEX/U.FL connectors on PCB - 1x USB 2.0 Type-A - 1x USB 2.0 mini Type-B in R36AH-U2 version - USB power is controlled by GPIO - 6/7x LED (5/6 of them are driven by GPIO) - 2x button (reset, wifi/wps) - external h/w watchdog (EM6324QYSP5B, enabled by default) - DC jack with lock, for main power input (12 V) - UART (4-pin, 2.54 mm pitch) header on PCB Optional/additional features in R36A series (R36A was the first model): - for R36AH: USB 2.0 hub* - for R36AH-U2: USB 2.0 hub*, 1x USB 2.0 mini Type-B, one more LED *) there are at least three different USB 2.0 hub in R36AH/-U2 variants: - Terminus-Tech FE 1.1 - Genesys Logic GL852G - Genesys Logic GL850G (used in latests revision) Flash instruction: You can use sysupgrade image directly in vendor firmware which is based on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot: 1. Configure PC with static IP 192.168.1.2/24. 2. Connect PC with one of RJ45 ports, press the reset button, power up device, wait for first blink of all LEDs (indicates network setup), then keep button for 3 following blinks and release it. 3. Open 192.168.1.1 address in your browser and upload sysupgrade image. Signed-off-by: Piotr Dymacz --- diff --git a/target/linux/ath79/dts/qca9531_alfa-network_r36a.dts b/target/linux/ath79/dts/qca9531_alfa-network_r36a.dts new file mode 100644 index 0000000000..18aaa85f5c --- /dev/null +++ b/target/linux/ath79/dts/qca9531_alfa-network_r36a.dts @@ -0,0 +1,190 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qca953x.dtsi" + +#include +#include + +/ { + model = "ALFA Network R36A"; + compatible = "alfa-network,r36a", "qca,qca9531"; + + aliases { + label-mac-device = &wmac; + led-boot = &led_status; + led-failsafe = &led_status; + led-running = &led_status; + led-upgrade = &led_status; + }; + + gpio-export { + compatible = "gpio-export"; + #size-cells = <0>; + + usb-power { + gpio-export,name = "usb-power"; + gpio-export,output = <1>; + gpios = <&gpio 3 GPIO_ACTIVE_HIGH>; + }; + + watchdog-enable { + gpio-export,name = "watchdog-enable"; + gpio-export,output = <1>; + gpios = <&gpio 1 GPIO_ACTIVE_HIGH>; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + linux,code = ; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + + rfkill { + label = "rfkill"; + linux,code = ; + gpios = <&gpio 17 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + }; + + leds { + compatible = "gpio-leds"; + + pinctrl-names = "default"; + pinctrl-0 = <&enable_gpio4 &enable_gpio16>; + + lan { + label = "r36a:blue:lan"; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + }; + + led_status: status { + label = "r36a:blue:status"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + }; + + usb { + label = "r36a:blue:usb"; + gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + trigger-sources = <&hub_port0>; + linux,default-trigger = "usbport"; + }; + + wan { + label = "r36a:blue:wan"; + gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + }; + + wlan { + label = "r36a:blue:wlan"; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + }; + + watchdog { + compatible = "linux,wdt-gpio"; + gpios = <&gpio 0 GPIO_ACTIVE_HIGH>; + hw_algo = "toggle"; + hw_margin_ms = <25000>; + always-running; + }; +}; + +ð0 { + status = "okay"; + + phy-handle = <&swphy4>; + mtd-mac-address = <&art 0x0>; +}; + +ð1 { + /* Workaround: keep the Ethernet interfaces order/mapping correct + * (GMAC0 -> eth0, GMAC1 -> eth1, same as in old ar71xx target) */ + compatible = "qca,qca9530-eth", "syscon", "simple-mfd"; + + mtd-mac-address = <&art 0x6>; +}; + +&pinmux { + enable_gpio4: pinmux_enable_gpio4 { + pinctrl-single,bits = <0x04 0x0 0xff>; + }; + + enable_gpio16: pinmux_enable_gpio16 { + pinctrl-single,bits = <0x10 0x0 0xff>; + }; +}; + +&spi { + status = "okay"; + + num-cs = <1>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <50000000>; + m25p,fast-read; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x000000 0x060000>; + read-only; + }; + + partition@60000 { + label = "u-boot-env"; + reg = <0x060000 0x010000>; + }; + + art: partition@70000 { + label = "art"; + reg = <0x070000 0x010000>; + read-only; + }; + + partition@80000 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0x080000 0xf80000>; + }; + }; + }; +}; + +&uart { + status = "okay"; +}; + +&usb0 { + status = "okay"; + + #address-cells = <1>; + #size-cells = <0>; + + hub_port0: port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; +}; + +&usb_phy { + status = "okay"; +}; + +&wmac { + status = "okay"; + + mtd-cal-data = <&art 0x1000>; +}; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds index 78726afecf..6e488949e4 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds @@ -17,6 +17,10 @@ alfa-network,ap121fe|\ avm,fritz450e) ucidef_set_led_netdev "lan" "LAN" "$boardname:green:lan" "eth0" ;; +alfa-network,r36a) + ucidef_set_led_netdev "lan" "LAN" "$boardname:blue:lan" "eth0" + ucidef_set_led_switch "wan" "WAN" "$boardname:blue:wan" "switch0" "0x10" + ;; avm,fritz1750e) ucidef_set_led_netdev "lan" "LAN" "$boardname:green:lan" "eth0" ucidef_set_rssimon "wlan1" "200000" "1" diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index ab8e24adde..d13d714f88 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -402,6 +402,7 @@ ath79_setup_macs() ;; alfa-network,ap121f|\ alfa-network,ap121fe|\ + alfa-network,r36a|\ engenius,ens202ext-v1) label_mac=$(mtd_get_mac_binary art 0x1002) ;; diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index ce927ecd4f..605f66f77f 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -237,6 +237,16 @@ define Device/alfa-network_ap121fe endef TARGET_DEVICES += alfa-network_ap121fe +define Device/alfa-network_r36a + SOC := qca9531 + DEVICE_VENDOR := ALFA Network + DEVICE_MODEL := R36A + DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport + IMAGE_SIZE := 15872k + SUPPORTED_DEVICES += r36a +endef +TARGET_DEVICES += alfa-network_r36a + define Device/allnet_all-wap02860ac SOC := qca9558 DEVICE_VENDOR := ALLNET