From: Anderson Vulczak Date: Sat, 5 Oct 2019 13:44:55 +0000 (-0300) Subject: ath79: add support for TP-Link Archer C6 v2 (US) and A6 (US/TW) X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=9b90dc05f58c619962e69e36d275b6ea56893496;p=openwrt%2Fstaging%2Fblocktrron.git ath79: add support for TP-Link Archer C6 v2 (US) and A6 (US/TW) This patch is based on #1689 and adds support for TP-Link Archer C6 v2 (US) and A6 (US/TW). The hardware is the same as EU and RU variant, except for GPIOs (LEDS/Buttons), flash(chip/partitions) and UART being available on the board. - SOC: Qualcomm QCA9563 @ 775MHz - Flash: GigaDevice GD25Q127CS1G (16MiB) - RAM: Zentel A3R1GE40JBF (128 MiB DDR2) - Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN - Wireless: - 2.4GHz (bgn) QCA9563 integrated (3x3) - 5GHz (ac) Qualcomm QCA9886 (2x2) - Button: 1x power, 1x reset, 1x wps - LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps - UART: 115200, 8n1 (header available on board) Known issues: - Wireless: 5GHz is known to have lower RSSI signal, it affects speed and range. Flash instructions: Upload openwrt-ath79-generic-tplink_archer-c6-v2-us-squashfs-factory.bin via the router Web interface. Flash instruction using tftp recovery: 1. Connect the computer to one of the LAN ports of the router 2. Set the computer IP to 192.168.0.66 3. Start a tftp server with the OpenWrt factory image in the tftp root directory renamed to ArcherA6v2_tp_recovery.bin. 4. Connect power cable to router, press and hold the reset button and turn the router on 5. Keep the reset button pressed until the WPS LED lights up 6. Wait ~150 seconds to complete flashing Flash partitioning: I've followed #1689 for defining the partition layout for this patch. The partition named as "tplink" @ 0xfd0000 is marked as read only as it is where some config for stock firmware are stored. On stock firmware those stock partitions starts at 0xfd9400 however I had not been able to make it functional starting on the same address as on stock fw, so it has been partitioned following #1689 and not the stock partition layout for this specific partition. Due to that firmware/rootfs partition lenght is 0xf80000 and not 0xf89400 as stock. According to the GPL code, the EU/RU/JP variant does have different GPIO pins assignment to LEDs and buttons, also the flash memory layout is different. GPL Source Code: https://static.tp-link.com/resources/gpl/gpl-A6v2_us.tar.gz Signed-off-by: Anderson Vulczak [wrap commit message, remove soft_ver change for C6 v2 EU, move LED aliases to DTS files, remove dts-v1 in DTSI, node/property reorder in DTSI] Signed-off-by: Adrian Schmutzler --- diff --git a/target/linux/ath79/dts/qca9563_tplink_archer-c6-v2-us.dts b/target/linux/ath79/dts/qca9563_tplink_archer-c6-v2-us.dts new file mode 100644 index 0000000000..3a6f00bf4e --- /dev/null +++ b/target/linux/ath79/dts/qca9563_tplink_archer-c6-v2-us.dts @@ -0,0 +1,130 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include "qca9563_tplink_archer-x6-v2.dtsi" + +/ { + compatible = "tplink,archer-c6-v2-us", "qca,qca9563"; + model = "TP-Link Archer C6 v2 (US) / A6 v2 (US/TW)"; + + aliases { + led-boot = &led_power; + led-failsafe = &led_power; + led-running = &led_power; + led-upgrade = &led_power; + }; + + leds { + compatible = "gpio-leds"; + + led_power: power { + label = "tp-link:green:power"; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + + wlan2g { + label = "tp-link:green:wlan2g"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + + wlan5g { + label = "tp-link:green:wlan5g"; + gpios = <&gpio 9 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + lan { + label = "tp-link:green:lan"; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + }; + + wan { + label = "tp-link:green:wan"; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + }; + + wan_fail { + label = "tp-link:amber:wan"; + gpios = <&gpio 7 GPIO_ACTIVE_LOW>; + }; + + wps { + label = "tp-link:green:wps"; + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "Reset button"; + linux,code = ; + gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + + wps { + label = "WPS button"; + linux,code = ; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + }; +}; + +&spi { + status = "okay"; + + num-cs = <1>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "factory-boot"; + reg = <0x000000 0x020000>; + read-only; + }; + + mac: partition@20000 { + label = "mac"; + reg = <0x020000 0x010000>; + read-only; + }; + + partition@30000 { + label = "u-boot"; + reg = <0x030000 0x020000>; + read-only; + }; + + partition@50000 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0x050000 0xf80000>; + }; + + partition@fd0000 { + label = "tplink"; + reg = <0xfd0000 0x020000>; + read-only; + }; + + art: partition@ff0000 { + label = "art"; + reg = <0xff0000 0x010000>; + read-only; + }; + }; + }; +}; diff --git a/target/linux/ath79/dts/qca9563_tplink_archer-c6-v2.dts b/target/linux/ath79/dts/qca9563_tplink_archer-c6-v2.dts index 5caec6fab1..e7ceec9b37 100644 --- a/target/linux/ath79/dts/qca9563_tplink_archer-c6-v2.dts +++ b/target/linux/ath79/dts/qca9563_tplink_archer-c6-v2.dts @@ -5,5 +5,120 @@ / { compatible = "tplink,archer-c6-v2", "qca,qca9563"; - model = "TP-Link Archer C6 v2"; + model = "TP-Link Archer C6 v2 (EU/RU/JP)"; + + aliases { + led-boot = &led_power; + led-failsafe = &led_power; + led-running = &led_power; + led-upgrade = &led_power; + }; + + leds { + compatible = "gpio-leds"; + + led_power: power { + label = "tp-link:green:power"; + gpios = <&gpio 17 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + + wlan2g { + label = "tp-link:green:wlan2g"; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + + wlan5g { + label = "tp-link:green:wlan5g"; + gpios = <&gpio 19 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + lan { + label = "tp-link:green:lan"; + gpios = <&gpio 20 GPIO_ACTIVE_LOW>; + }; + + wan { + label = "tp-link:green:wan"; + gpios = <&gpio 7 GPIO_ACTIVE_LOW>; + }; + + wan_fail { + label = "tp-link:amber:wan"; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + }; + + wps { + label = "tp-link:green:wps"; + gpios = <&gpio 9 GPIO_ACTIVE_LOW>; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "Reset button"; + linux,code = ; + gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + + wps { + label = "WPS button"; + linux,code = ; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + }; +}; + +&spi { + status = "okay"; + + num-cs = <1>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x000000 0x020000>; + read-only; + }; + + mac: partition@20000 { + label = "mac"; + reg = <0x020000 0x010000>; + read-only; + }; + + partition@30000 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0x030000 0x7a0000>; + }; + + partition@7d0000 { + label = "tplink"; + reg = <0x7d0000 0x020000>; + read-only; + }; + + art: partition@7f0000 { + label = "art"; + reg = <0x7f0000 0x010000>; + read-only; + }; + }; + }; }; diff --git a/target/linux/ath79/dts/qca9563_tplink_archer-x6-v2.dtsi b/target/linux/ath79/dts/qca9563_tplink_archer-x6-v2.dtsi index f1a1f5673d..367f826b9d 100644 --- a/target/linux/ath79/dts/qca9563_tplink_archer-x6-v2.dtsi +++ b/target/linux/ath79/dts/qca9563_tplink_archer-x6-v2.dtsi @@ -1,5 +1,4 @@ // SPDX-License-Identifier: GPL-2.0-or-later OR MIT -/dts-v1/; #include #include @@ -7,76 +6,12 @@ #include "qca956x.dtsi" / { - chosen { - bootargs = "console=ttyS0,115200n8"; - }; - aliases { - led-boot = &led_power; - led-failsafe = &led_power; - led-running = &led_power; - led-upgrade = &led_power; label-mac-device = ð0; }; - leds { - compatible = "gpio-leds"; - - led_power: power { - label = "tp-link:green:power"; - gpios = <&gpio 17 GPIO_ACTIVE_LOW>; - default-state = "on"; - }; - - wlan2g { - label = "tp-link:green:wlan2g"; - gpios = <&gpio 15 GPIO_ACTIVE_LOW>; - linux,default-trigger = "phy1tpt"; - }; - - wlan5g { - label = "tp-link:green:wlan5g"; - gpios = <&gpio 19 GPIO_ACTIVE_LOW>; - linux,default-trigger = "phy0tpt"; - }; - - lan { - label = "tp-link:green:lan"; - gpios = <&gpio 20 GPIO_ACTIVE_LOW>; - }; - - wan { - label = "tp-link:green:wan"; - gpios = <&gpio 7 GPIO_ACTIVE_LOW>; - }; - - wan_fail { - label = "tp-link:amber:wan"; - gpios = <&gpio 8 GPIO_ACTIVE_LOW>; - }; - - wps { - label = "tp-link:green:wps"; - gpios = <&gpio 9 GPIO_ACTIVE_LOW>; - }; - }; - - keys { - compatible = "gpio-keys"; - - reset { - label = "Reset button"; - linux,code = ; - gpios = <&gpio 5 GPIO_ACTIVE_LOW>; - debounce-interval = <60>; - }; - - wps { - label = "WPS button"; - linux,code = ; - gpios = <&gpio 6 GPIO_ACTIVE_LOW>; - debounce-interval = <60>; - }; + chosen { + bootargs = "console=ttyS0,115200n8"; }; }; @@ -92,54 +27,6 @@ status = "okay"; }; -&spi { - status = "okay"; - - num-cs = <1>; - - flash@0 { - compatible = "jedec,spi-nor"; - reg = <0>; - spi-max-frequency = <25000000>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "u-boot"; - reg = <0x000000 0x020000>; - read-only; - }; - - mac: partition@20000 { - label = "mac"; - reg = <0x020000 0x010000>; - read-only; - }; - - partition@30000 { - compatible = "denx,uimage"; - label = "firmware"; - reg = <0x030000 0x7a0000>; - }; - - partition@7d0000 { - label = "tplink"; - reg = <0x7d0000 0x020000>; - read-only; - }; - - art: partition@7f0000 { - label = "art"; - reg = <0x7f0000 0x010000>; - read-only; - }; - }; - }; -}; - &mdio0 { status = "okay"; @@ -161,8 +48,9 @@ status = "okay"; phy-mode = "sgmii"; - mtd-mac-address = <&mac 0x8>; phy-handle = <&phy0>; + + mtd-mac-address = <&mac 0x8>; }; &wmac { diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds index c914090cf9..5561677ec3 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds @@ -146,7 +146,8 @@ tplink,tl-wr1043n-v5) ucidef_set_led_switch "lan3" "LAN3" "tp-link:green:lan3" "switch0" "0x04" ucidef_set_led_switch "lan4" "LAN4" "tp-link:green:lan4" "switch0" "0x02" ;; -tplink,archer-c6-v2) +tplink,archer-c6-v2|\ +tplink,archer-c6-v2-us) ucidef_set_led_switch "lan" "LAN" "tp-link:green:lan" "switch0" "0x3C" ucidef_set_led_switch "wan" "WAN" "tp-link:green:wan" "switch0" "0x02" ;; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index 7090825c2f..e811f85f0e 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -207,6 +207,7 @@ ath79_setup_interfaces() ;; tplink,archer-a7-v5|\ tplink,archer-c6-v2|\ + tplink,archer-c6-v2-us|\ tplink,archer-c7-v4|\ tplink,archer-c7-v5|\ tplink,tl-wdr3600-v1|\ diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 97233fa0e4..062caf6ad5 100644 --- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -146,7 +146,8 @@ case "$FIRMWARE" in tplink,archer-c59-v2|\ tplink,archer-c60-v1|\ tplink,archer-c60-v2|\ - tplink,archer-c6-v2) + tplink,archer-c6-v2|\ + tplink,archer-c6-v2-us) caldata_extract "art" 0x5000 0x2f20 ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary mac 0x8) -1) ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \ diff --git a/target/linux/ath79/image/generic-tp-link.mk b/target/linux/ath79/image/generic-tp-link.mk index ae956eb98e..f5e1a90418 100644 --- a/target/linux/ath79/image/generic-tp-link.mk +++ b/target/linux/ath79/image/generic-tp-link.mk @@ -88,12 +88,26 @@ define Device/tplink_archer-c6-v2 ATH_SOC := qca9563 IMAGE_SIZE := 7808k DEVICE_MODEL := Archer C6 - DEVICE_VARIANT := v2 + DEVICE_VARIANT := v2 (EU/RU/JP) TPLINK_BOARD_ID := ARCHER-C6-V2 DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct endef TARGET_DEVICES += tplink_archer-c6-v2 +define Device/tplink_archer-c6-v2-us + $(Device/tplink-safeloader-uimage) + ATH_SOC := qca9563 + IMAGE_SIZE := 15872k + DEVICE_MODEL := Archer C6 + DEVICE_VARIANT := v2 (US) + DEVICE_ALT0_VENDOR := TP-Link + DEVICE_ALT0_MODEL := Archer A6 + DEVICE_ALT0_VARIANT := v2 (US/TW) + TPLINK_BOARD_ID := ARCHER-C6-V2-US + DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct +endef +TARGET_DEVICES += tplink_archer-c6-v2-us + define Device/tplink_archer-c60-v1 $(Device/tplink-safeloader-uimage) ATH_SOC := qca9561 diff --git a/tools/firmware-utils/src/tplink-safeloader.c b/tools/firmware-utils/src/tplink-safeloader.c index f8b8491326..c09ea347b2 100644 --- a/tools/firmware-utils/src/tplink-safeloader.c +++ b/tools/firmware-utils/src/tplink-safeloader.c @@ -881,7 +881,7 @@ static struct device_info boards[] = { .last_sysupgrade_partition = "file-system", }, - /** Firmware layout for the C6v2 */ + /** Firmware layout for the Archer C6 v2 (EU/RU/JP) */ { .id = "ARCHER-C6-V2", .vendor = "", @@ -916,6 +916,40 @@ static struct device_info boards[] = { .last_sysupgrade_partition = "file-system", }, + /** Firmware layout for the Archer C6 v2 (US) and A6 v2 (US/TW) */ + { + .id = "ARCHER-C6-V2-US", + .vendor = "", + .support_list = + "SupportList:\n" + "{product_name:Archer A6,product_ver:2.0.0,special_id:55530000}\n" + "{product_name:Archer A6,product_ver:2.0.0,special_id:54570000}\n" + "{product_name:Archer C6,product_ver:2.0.0,special_id:55530000}\n", + .support_trail = '\x00', + .soft_ver = "soft_ver:1.1.1\n", + + .partitions = { + {"factory-boot", 0x00000, 0x20000}, + {"default-mac", 0x20000, 0x00200}, + {"pin", 0x20200, 0x00100}, + {"product-info", 0x20300, 0x00200}, + {"device-id", 0x20500, 0x0fb00}, + {"fs-uboot", 0x30000, 0x20000}, + {"firmware", 0x50000, 0xf89400}, + {"soft-version", 0xfd9400, 0x00100}, + {"extra-para", 0xfd9500, 0x00100}, + {"support-list", 0xfd9600, 0x00200}, + {"profile", 0xfd9800, 0x03000}, + {"default-config", 0xfdc800, 0x03000}, + {"partition-table", 0xfdf800, 0x00800}, + {"user-config", 0xfe0000, 0x0c000}, + {"certificate", 0xfec000, 0x04000}, + {"radio", 0xff0000, 0x10000}, + {NULL, 0, 0} + }, + .first_sysupgrade_partition = "os-image", + .last_sysupgrade_partition = "file-system", + }, /** Firmware layout for the C60v1 */ { @@ -2069,6 +2103,9 @@ static void build_image(const char *output, } else if (strcasecmp(info->id, "ARCHER-C6-V2") == 0) { const char mdat[11] = {0x00, 0x00, 0x00, 0x02, 0x00, 0x00, 0x00, 0x00, 0x00, 0x01, 0x00}; parts[5] = put_data("extra-para", mdat, 11); + } else if (strcasecmp(info->id, "ARCHER-C6-V2-US") == 0) { + const char mdat[11] = {0x00, 0x00, 0x00, 0x02, 0x00, 0x00, 0x00, 0x00, 0x01, 0x01, 0x00}; + parts[5] = put_data("extra-para", mdat, 11); } size_t len;