From: George Witt Date: Mon, 5 Aug 2024 21:29:37 +0000 (-0500) Subject: ipq807x: add support for TP-Link EAP660 HD v1 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=9b336455663482739868953b8b1bd46e1dd0943f;p=openwrt%2Fstaging%2Fxback.git ipq807x: add support for TP-Link EAP660 HD v1 Specifications: * SoC: Qualcomm IPQ8072A (64-bit Quad-core Arm Cortex-A53 @ 2200MHz) * Memory: 2x ESMT M15T4G16256A-DEBG2G (1 GiB DDR3-1866 13-13-13) * Serial Port: 3v3 TTL 115200n8 * Wi-Fi: QCN5054 (4x4 5 GHz 802.11ax) * Wi-Fi: QCN5024 (4x4 2.4 GHz 802.11b/g/n/ax) * Ethernet: QCA8081 (10/100/1000/2.5GBASE-T) * Flash: Winbond W29N01HZSINF (128 MiB) * LEDs: 1x Blue Status (GPIO 42 Active High) * Buttons: 1x Reset (GPIO 50 Active Low) Installation Instructions (Serial+TFTP): 1. Solder 4 pin header to JP1 and bridge pads of R58 and R62. 2. Connect 3V3 TTL port to TX, RX, and GND, which are positions 1, 2, and 3 respectively. Be sure to crossover TX and RX. 3. Copy RAM firmware image openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-initramfs-uImage.itb to TFTP server root, available at 192.168.10.1. 4. Connect PoE ethernet cable to the RJ45 port and hold Ctrl+B in the serial console (115200 baud) until autoboot is halted. 5. Run the following commands in the U-boot prompt: # tftpboot 0x44000000 openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-initramfs-uImage.itb # bootm You may need to type Ctrl+C and Enter before running these commands to clear invisible characters from the buffer. 6. Run the following command in a terminal to copy the sysupgrade image to be installed (check IP address): $ scp openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/ 7. Activate the OpenWrt serial console and run the following commands: # cd /tmp # sysupgrade -n openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-squashfs-sysupgrade.bin 8. The AP will reboot and OpenWrt will be successfully installed. Signed-off-by: George Witt Link: https://github.com/openwrt/openwrt/pull/15832 Signed-off-by: Robert Marko --- diff --git a/package/boot/uboot-envtools/files/qualcommax_ipq807x b/package/boot/uboot-envtools/files/qualcommax_ipq807x index 852e05f29a..f5fb07a4db 100644 --- a/package/boot/uboot-envtools/files/qualcommax_ipq807x +++ b/package/boot/uboot-envtools/files/qualcommax_ipq807x @@ -38,7 +38,8 @@ linksys,mx8500) ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x40000" "0x20000" "2" ;; netgear,sxr80|\ -netgear,sxs80) +netgear,sxs80|\ +tplink,eap660hd-v1) idx="$(find_mtd_index 0:appsblenv)" [ -n "$idx" ] && \ ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x40000" "0x20000" diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile index fb5b18cb3d..1c95983964 100644 --- a/package/firmware/ipq-wifi/Makefile +++ b/package/firmware/ipq-wifi/Makefile @@ -52,6 +52,7 @@ ALLWIFIBOARDS:= \ qnap_301w \ redmi_ax6 \ spectrum_sax1v1k \ + tplink_eap660hd-v1 \ wallys_dr40x9 \ xiaomi_ax3600 \ xiaomi_ax9000 \ @@ -177,6 +178,7 @@ $(eval $(call generate-ipq-wifi-package,qnap_301w,QNAP 301w)) $(eval $(call generate-ipq-wifi-package,prpl_haze,prpl Haze)) $(eval $(call generate-ipq-wifi-package,redmi_ax6,Redmi AX6)) $(eval $(call generate-ipq-wifi-package,spectrum_sax1v1k,Spectrum SAX1V1K)) +$(eval $(call generate-ipq-wifi-package,tplink_eap660hd-v1,TP-Link EAP660 HD v1)) $(eval $(call generate-ipq-wifi-package,wallys_dr40x9,Wallys DR40X9)) $(eval $(call generate-ipq-wifi-package,xiaomi_ax3600,Xiaomi AX3600)) $(eval $(call generate-ipq-wifi-package,xiaomi_ax9000,Xiaomi AX9000)) diff --git a/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8072-eap660hd-v1.dts b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8072-eap660hd-v1.dts new file mode 100644 index 0000000000..500847c98b --- /dev/null +++ b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8072-eap660hd-v1.dts @@ -0,0 +1,131 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR BSD-2-Clause + +/dts-v1/; + +#include "ipq8074.dtsi" +#include "ipq8074-hk-cpu.dtsi" +#include "ipq8074-ess.dtsi" +#include +#include +#include + +/ { + model = "TP-Link EAP660 HD v1"; + compatible = "tplink,eap660hd-v1", "qcom,ipq8074"; + + aliases { + serial0 = &blsp1_uart5; + led-boot = &led_status_blue; + led-failsafe = &led_status_blue; + led-running = &led_status_blue; + led-upgrade = &led_status_blue; + }; + + chosen { + stdout-path = "serial0,115200n8"; + bootargs-append = " root=/dev/ubiblock0_1"; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&tlmm 50 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_status_blue: status-blue { + function = LED_FUNCTION_STATUS; + gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>; + color = ; + }; + }; +}; + +&blsp1_uart5 { + status = "okay"; +}; + +&tlmm { + mdio_pins: mdio-pins { + mdc { + pins = "gpio68"; + function = "mdc"; + drive-strength = <8>; + bias-pull-up; + }; + + mdio { + pins = "gpio69"; + function = "mdio"; + drive-strength = <8>; + bias-pull-up; + }; + }; +}; + +&mdio { + status = "okay"; + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + reset-gpios = <&tlmm 25 GPIO_ACTIVE_LOW>; + + qca8081_28: ethernet-phy@28 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <28>; + }; +}; + +&dp5 { + status = "okay"; + phy-mode = "sgmii"; + phy-handle = <&qca8081_28>; + label = "lan"; +}; + +&switch { + status = "okay"; + switch_lan_bmp = ; + switch_mac_mode1 = ; + + qcom,port_phyinfo { + port@5 { + phy_address = <28>; + port_id = <5>; + port_mac_sel = "QGMAC_PORT"; + }; + }; +}; + +&edma { + status = "okay"; +}; + +&qpic_bam { + status = "okay"; +}; + +&qpic_nand { + status = "okay"; + + nand@0 { + reg = <0>; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + nand-bus-width = <8>; + + partitions { + compatible = "qcom,smem-part"; + }; + }; +}; + +&wifi { + status = "okay"; + qcom,ath11k-calibration-variant = "TP-Link-EAP660-HD-v1"; +}; diff --git a/target/linux/qualcommax/image/ipq807x.mk b/target/linux/qualcommax/image/ipq807x.mk index 8caa6a322c..b62734334d 100644 --- a/target/linux/qualcommax/image/ipq807x.mk +++ b/target/linux/qualcommax/image/ipq807x.mk @@ -344,6 +344,20 @@ define Device/spectrum_sax1v1k endef TARGET_DEVICES += spectrum_sax1v1k +define Device/tplink_eap660hd-v1 + $(call Device/FitImage) + $(call Device/UbiFit) + DEVICE_VENDOR := TP-Link + DEVICE_MODEL := EAP660 HD + DEVICE_VARIANT := v1 + BLOCKSIZE := 128k + PAGESIZE := 2048 + SOC := ipq8072 + DEVICE_PACKAGES := ipq-wifi-tplink_eap660hd-v1 + TPLINK_SUPPORT_STRING := SupportList:\r\nEAP660 HD(TP-Link|UN|AX3600-D):1.0\r\n +endef +TARGET_DEVICES += tplink_eap660hd-v1 + define Device/xiaomi_ax3600 $(call Device/FitImage) $(call Device/UbiFit) diff --git a/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network b/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network index f87dbdd2be..437581d001 100644 --- a/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network +++ b/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network @@ -60,6 +60,9 @@ ipq807x_setup_interfaces() qnap,301w) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 10g-2" "10g-1" ;; + tplink,eap660hd-v1) + ucidef_set_interface_lan "lan" "dhcp" + ;; zyxel,nbg7815) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 10g" "wan" ;; @@ -89,6 +92,10 @@ ipq807x_setup_macs() lan_mac=$(macaddr_add $label_mac 1) wan_mac=$label_mac ;; + tplink,eap660hd-v1) + label_mac=$(get_mac_binary /tmp/factory_data/default-mac 0) + lan_mac=$label_mac + ;; esac [ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac diff --git a/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata b/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata index e413801ef9..2e741f0448 100644 --- a/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata +++ b/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata @@ -80,6 +80,13 @@ case "$FIRMWARE" in spectrum,sax1v1k) caldata_extract_mmc "0:ART" 0x1000 0x20000 ;; + tplink,eap660hd-v1) + caldata_from_file "/tmp/factory_data/radio" 0 0x20000 + label_mac=$(get_mac_binary /tmp/factory_data/default-mac 0) + ath11k_patch_mac $label_mac 1 + ath11k_patch_mac $(macaddr_add $label_mac 1) 0 + ath11k_set_macflag + ;; zbtlink,zbt-z800ax) caldata_extract "0:art" 0x1000 0x20000 label_mac=$(get_mac_label) diff --git a/target/linux/qualcommax/ipq807x/base-files/lib/preinit/09_mount_factory_data b/target/linux/qualcommax/ipq807x/base-files/lib/preinit/09_mount_factory_data new file mode 100644 index 0000000000..59fde529d3 --- /dev/null +++ b/target/linux/qualcommax/ipq807x/base-files/lib/preinit/09_mount_factory_data @@ -0,0 +1,19 @@ +#!/bin/sh + +preinit_mount_factory_data() { + local mtd_path + + . /lib/functions.sh + . /lib/functions/system.sh + + case $(board_name) in + tplink,eap660hd-v1) + mtd_path=$(find_mtd_chardev "factory_data") + ubiattach --dev-path="$mtd_path" --devn=1 + mkdir /tmp/factory_data + mount -o ro,noatime -t ubifs ubi1:ubi_factory_data /tmp/factory_data + ;; + esac +} + +boot_hook_add preinit_main preinit_mount_factory_data diff --git a/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh b/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh index f78a4b04f1..92ef5fef2c 100644 --- a/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh +++ b/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh @@ -35,6 +35,79 @@ asus_initial_setup() { ubirmvol /dev/ubi0 -N jffs2 } +remove_oem_ubi_volume() { + local oem_volume_name="$1" + local oem_ubivol + local mtdnum + local ubidev + + mtdnum=$(find_mtd_index "$CI_UBIPART") + if [ ! "$mtdnum" ]; then + return + fi + + ubidev=$(nand_find_ubi "$CI_UBIPART") + if [ ! "$ubidev" ]; then + ubiattach --mtdn="$mtdnum" + ubidev=$(nand_find_ubi "$CI_UBIPART") + fi + + if [ "$ubidev" ]; then + oem_ubivol=$(nand_find_volume "$ubidev" "$oem_volume_name") + [ "$oem_ubivol" ] && ubirmvol "/dev/$ubidev" --name="$oem_volume_name" + fi +} + +tplink_get_boot_part() { + local cur_boot_part + local args + + # Try to find rootfs from kernel arguments + read -r args < /proc/cmdline + for arg in $args; do + local ubi_mtd_arg=${arg#ubi.mtd=} + case "$ubi_mtd_arg" in + rootfs|rootfs_1) + echo "$ubi_mtd_arg" + return + ;; + esac + done + + # Fallback to u-boot env (e.g. when running initramfs) + cur_boot_part="$(/usr/sbin/fw_printenv -n tp_boot_idx)" + case $cur_boot_part in + 1) + echo rootfs_1 + ;; + 0|*) + echo rootfs + ;; + esac +} + +tplink_do_upgrade() { + local new_boot_part + + case $(tplink_get_boot_part) in + rootfs) + CI_UBIPART="rootfs_1" + new_boot_part=1 + ;; + rootfs_1) + CI_UBIPART="rootfs" + new_boot_part=0 + ;; + esac + + fw_setenv -s - <<-EOF + tp_boot_idx $new_boot_part + EOF + + remove_oem_ubi_volume ubi_rootfs + nand_do_upgrade "$1" +} + platform_check_image() { return 0; } @@ -117,6 +190,9 @@ platform_do_upgrade() { rootfsname="rootfs" mmc_do_upgrade "$1" ;; + tplink,eap660hd-v1) + tplink_do_upgrade "$1" + ;; redmi,ax6|\ xiaomi,ax3600|\ xiaomi,ax9000)