From: Mark Mentovai <mark@mentovai.com>
Date: Thu, 11 Nov 2021 17:24:24 +0000 (-0500)
Subject: ipq40xx: Convert mikrotik,wap-ac to DSA
X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=9a8e008188a11813a90b77ba32d24c0cca225bf9;p=openwrt%2Fstaging%2Fjow.git

ipq40xx: Convert mikrotik,wap-ac to DSA

As done previously, this preserves the MAC addresses of they physical
Ethernet ports. The interfaces are renamed as eth0 is in use for the
native GMAC; the new interface naming matches the physical port labels.
 - sw-eth1 corresponds to the physical port labeled ETH1 and has the
   base MAC address. This port can be used to power the device.
 - sw-eth2 corresponds to the physical port labeled ETH2 and has a MAC
   address one greater than the base.

As this device has 2 physical ports, they are each connected to their
respective PHYs, allowing the link status to be visible to software.
Since they are not marked on the case with any role (such as LAN or
WAN), both are bridged to the lan network by default, although this can
easily be changed if needed.

Signed-off-by: Mark Mentovai <mark@mentovai.com>
---

diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index 1089a7f3f8..36f1f7c24a 100644
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -52,11 +52,14 @@ ipq40xx_setup_interfaces()
 	cellc,rtl30vw)
 		ucidef_set_interface_lan "lan1 lan2"
 		;;
+	compex,wpj428)
+		ucidef_set_interface_lan "lan1 lan2"
+		;;
 	glinet,gl-b1300)
 		ucidef_set_interfaces_lan_wan "lan1 lan2" "wan"
 		;;
-	compex,wpj428)
-		ucidef_set_interface_lan "lan1 lan2"
+	mikrotik,wap-ac)
+		ucidef_set_interface_lan "sw-eth1 sw-eth2"
 		;;
 	zte,mf286d)
 		ucidef_set_interfaces_lan_wan "lan2 lan3 lan4" "wan"
diff --git a/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh b/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh
index 18c24e0511..e4a5eb3e89 100644
--- a/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh
+++ b/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh
@@ -26,8 +26,8 @@ preinit_set_mac_address() {
 		;;
 	mikrotik,wap-ac)
 		base_mac=$(cat /sys/firmware/mikrotik/hard_config/mac_base)
-		ip link set dev eth0 address "$base_mac"
-		ip link set dev eth1 address $(macaddr_add "$base_mac" 1)
+		ip link set dev sw-eth1 address "$base_mac"
+		ip link set dev sw-eth2 address $(macaddr_add "$base_mac" 1)
 		;;
 	zyxel,nbg6617)
 		base_mac=$(cat /sys/class/net/eth0/address)
diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-wap-ac.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-wap-ac.dts
index e6a6202216..ecbdfac15f 100644
--- a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-wap-ac.dts
+++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-wap-ac.dts
@@ -187,6 +187,24 @@
 	status = "okay";
 };
 
+&gmac {
+	status = "okay";
+};
+
+&switch {
+	status = "okay";
+};
+
+&swport4 {
+	status = "okay";
+	label = "sw-eth2";
+};
+
+&swport5 {
+	status = "okay";
+	label = "sw-eth1";
+};
+
 &wifi0 {
 	status = "okay";
 
diff --git a/target/linux/ipq40xx/image/mikrotik.mk b/target/linux/ipq40xx/image/mikrotik.mk
index 8491ff4a42..d1f0829cd3 100644
--- a/target/linux/ipq40xx/image/mikrotik.mk
+++ b/target/linux/ipq40xx/image/mikrotik.mk
@@ -69,5 +69,4 @@ define Device/mikrotik_wap-ac
 	SOC := qcom-ipq4018
 	DEVICE_PACKAGES := -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers
 endef
-# Missing DSA Setup
-#TARGET_DEVICES += mikrotik_wap-ac
+TARGET_DEVICES += mikrotik_wap-ac