From: Christian Marangi Date: Fri, 17 Feb 2023 02:43:29 +0000 (+0100) Subject: ipq806x: fix Linksys EAX500 family devices dead Ethernet switch X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=9a24040d20356482b4a481bbd62b287a9eb338f2;p=openwrt%2Fstaging%2Fthess.git ipq806x: fix Linksys EAX500 family devices dead Ethernet switch With 5.15 kernel version Linksys EAX500 family devices suffered from a big regression where the Ethernet switch became silent and started to malfunction. It was discovered later that the cause was not really the kernel upgrade itself but a hackish implementation of the hw implementation of these special routers. In the original Linksys source code, GPIO 63 was handled in a special way and was reset on reboot. Normally GPIO 63 is used for pcie2 reset but in every device we support, pcie2 is actually never used as nothing is attached to it. Linksys rerouted GPIO 63 to the switch reset pin and deviates from common hw implementation. Till now it was used an hack to handle this case... It was set pcie3 as working (while actually nothing was connected), set it to output low (for assert-deassert from the pcie init code) and be done with it. The result was that the GPIO was reset for enough time in early boot and everything worked correctly. This hack implementation was born to fail from the very start and in kernel 5.15 finally problem arised. In 5.15 pcie code changed and now the GPIO reset pin is not asserted as probe won't fail if nothing is connected to the line (the old behaviour) This result in the switch hold the reset pin and the Ethernet switch dead. On top of that with 5.15 code got optimized and simply attaching the GPIO reset to the mdio wasn't enough as the switch require at least 10ms to be correctly reset. So implement finally a correct solution where: - pcie2 is correctly disabled (nothing attached, unused) - drop the wrong output-low for pcie2 reset pin - define GPIO 63 as switch reset - Add the reset-gpios to the mdio0 node - Set the reset-post-delay-us to 12ms to correctly give time the switch to reset Fixes: #10983 Signed-off-by: Christian Marangi --- diff --git a/target/linux/ipq806x/files-5.10/arch/arm/boot/dts/qcom-ipq8064-eax500.dtsi b/target/linux/ipq806x/files-5.10/arch/arm/boot/dts/qcom-ipq8064-eax500.dtsi index e74d2dcdbd..e5282efaab 100644 --- a/target/linux/ipq806x/files-5.10/arch/arm/boot/dts/qcom-ipq8064-eax500.dtsi +++ b/target/linux/ipq806x/files-5.10/arch/arm/boot/dts/qcom-ipq8064-eax500.dtsi @@ -12,6 +12,18 @@ }; }; +&qcom_pinmux { + /* eax500 routers reuse the pcie2 reset pin for switch reset pin */ + switch_reset: switch_reset_pins { + mux { + pins = "gpio63"; + function = "gpio"; + drive-strength = <12>; + bias-pull-up; + }; + }; +}; + &usb3_0 { status = "okay"; }; @@ -30,10 +42,6 @@ status = "okay"; }; -&pcie2 { - status = "okay"; -}; - &nand { status = "okay"; @@ -160,6 +168,10 @@ pinctrl-0 = <&mdio0_pins>; pinctrl-names = "default"; + /* Switch from documentation require at least 10ms for reset */ + reset-gpios = <&qcom_pinmux 63 GPIO_ACTIVE_HIGH>; + reset-post-delay-us = <12000>; + phy0: ethernet-phy@0 { reg = <0>; qca,ar8327-initvals = < diff --git a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-eax500.dtsi b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-eax500.dtsi index adf5192ac8..910bd86bc5 100644 --- a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-eax500.dtsi +++ b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-eax500.dtsi @@ -12,6 +12,18 @@ }; }; +&qcom_pinmux { + /* eax500 routers reuse the pcie2 reset pin for switch reset pin */ + switch_reset: switch_reset_pins { + mux { + pins = "gpio63"; + function = "gpio"; + drive-strength = <12>; + bias-pull-up; + }; + }; +}; + &hs_phy_0 { status = "okay"; }; @@ -46,10 +58,6 @@ status = "okay"; }; -&pcie2 { - status = "okay"; -}; - &nand { status = "okay"; @@ -173,6 +181,10 @@ pinctrl-0 = <&mdio0_pins>; pinctrl-names = "default"; + /* Switch from documentation require at least 10ms for reset */ + reset-gpios = <&qcom_pinmux 63 GPIO_ACTIVE_HIGH>; + reset-post-delay-us = <12000>; + phy0: ethernet-phy@0 { reg = <0>; qca,ar8327-initvals = < diff --git a/target/linux/ipq806x/patches-5.10/082-ipq8064-dtsi-tweaks.patch b/target/linux/ipq806x/patches-5.10/082-ipq8064-dtsi-tweaks.patch index d6a4593749..301963f4f9 100644 --- a/target/linux/ipq806x/patches-5.10/082-ipq8064-dtsi-tweaks.patch +++ b/target/linux/ipq806x/patches-5.10/082-ipq8064-dtsi-tweaks.patch @@ -35,14 +35,6 @@ #interrupt-cells = <2>; interrupts = ; -@@ -155,6 +156,7 @@ - function = "pcie3_rst"; - drive-strength = <12>; - bias-disable; -+ output-low; - }; - }; - @@ -190,6 +192,7 @@ intc: interrupt-controller@2000000 { compatible = "qcom,msm-qgic2";