From: Zoltan HERPAI Date: Mon, 7 Sep 2020 16:52:31 +0000 (+0200) Subject: ath79: add support for Atheros DB120 reference board X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=98eb95dd0018d4f21a5b86b323074d5854e1bde3;p=openwrt%2Fstaging%2Fynezz.git ath79: add support for Atheros DB120 reference board Atheros DB120 reference board. Specifications: SoC: QCA9344 DRAM: 128Mb DDR2 Flash: 8Mb SPI-NOR, 128Mb NAND flash Switch: 5x 10/100Mbps via AR8229 switch (integrated into SoC), 5x 10/100/1000Mbps via QCA8237 via RGMII WLAN: AR9300 (SoC, 2.4G+5G) + AR9340 (PCIe, 5G-only) USB: 1x 2.0 UART: standard QCA UART header JTAG: yes Button: 1x reset LEDs: a lot Slots: 2x mPCIe + 1x mini-PCI, but using them requires additional undocumented changes. Misc: The board allows to boot off NAND, and there is I2S audio support as well - also requiring additional undocumented changes. Installation: 1. Original bootloader Connect the board to ethernet Set up a server with an IP address of 192.168.1.10 Make the openwrt-ath79-generic-atheros_db120-squashfs-factory.bin available via TFTP tftpboot 0x80060000 openwrt-ath79-generic-atheros_db120-squashfs-factory.bin erase 0x9f050000 +$filesize cp.b $fileaddr 0x9f050000 $filesize 2. pepe2k's u-boot_mod Connect the board to ethernet Set up a server with an IP address of 192.168.1.10 Make the openwrt-ath79-generic-atheros_db120-squashfs-factory.bin available via TFTP, as "firmware.bin" run fw_upg Reboot the board. Signed-off-by: Zoltan HERPAI [explicit factory recipe in generic.mk, sorting in 10-ath9k-eeprom, convert to nvmem, use fwconcat* names in DTS, remove unneeded DT labels, remove redundant uart node] Signed-off-by: Adrian Schmutzler --- diff --git a/target/linux/ath79/dts/ar9344_atheros_db120.dts b/target/linux/ath79/dts/ar9344_atheros_db120.dts new file mode 100644 index 0000000000..f96e31caca --- /dev/null +++ b/target/linux/ath79/dts/ar9344_atheros_db120.dts @@ -0,0 +1,250 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "ar9344.dtsi" + +#include +#include +#include + +/ { + model = "Atheros DB120 reference board"; + compatible = "atheros,db120", "qca,ar9344"; + + aliases { + led-boot = &led_system; + led-failsafe = &led_system; + led-running = &led_system; + led-upgrade = &led_system; + }; + + leds { + compatible = "gpio-leds"; + + wlan2g { + label = "green:wlan2g"; + gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + wlan5g { + label = "green:wlan5g"; + gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + + led_system: system { + label = "green:system"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + + usb { + label = "green:usb"; + gpios = <&gpio 11 GPIO_ACTIVE_LOW>; + trigger-sources = <&hub_port1>; + linux,default-trigger = "usbport"; + }; + }; + + leds-ath9k { + compatible = "gpio-leds"; + + wlan5g-ath { + label = "green:wlan5g-ath"; + gpios = <&ath9k 0 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + }; + + keys { + compatible = "gpio-keys"; + + wps { + linux,code = ; + label = "WPS button"; + gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + }; + + virtual_flash { + compatible = "mtd-concat"; + devices = <&fwconcat0 &fwconcat1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + reg = <0x0 0x0>; + label = "firmware"; + compatible = "openwrt,uimage", "denx,uimage"; + openwrt,ih-magic = ; + }; + }; + }; +}; + +&ref { + clock-frequency = <40000000>; +}; + +&spi { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + uboot: partition@0 { + label = "u-boot"; + reg = <0x000000 0x040000>; + read-only; + }; + + partition@40000 { + label = "u-boot-env"; + reg = <0x040000 0x010000>; + read-only; + }; + + fwconcat0: partition@50000 { + label = "fwconcat0"; + reg = <0x050000 0x630000>; + }; + + partition@680000 { + label = "loader"; + reg = <0x680000 0x010000>; + }; + + fwconcat1: partition@690000 { + label = "fwconcat1"; + reg = <0x690000 0x150000>; + }; + + partition@7e0000 { + label = "nvram"; + reg = <0x7e0000 0x010000>; + }; + + art: partition@7f0000 { + label = "art"; + reg = <0x7f0000 0x010000>; + read-only; + }; + }; + }; +}; + +ð0 { + status = "okay"; + + pll-data = <0x06000000 0x00000101 0x00001616>; + + nvmem-cells = <&macaddr_art_0>; + nvmem-cell-names = "mac-address"; + + phy-mode = "rgmii"; + phy-handle = <&phy0>; +}; + +&mdio0 { + status = "okay"; + + phy-mask = <0>; + + phy0: ethernet-phy@0 { + reg = <0>; + + qca,ar8327-initvals = < + 0x04 0x07600000 /* PORT0 PAD MODE CTRL */ + 0x10 0xc1000000 /* POWER_ON_STRAP */ + 0x7c 0x0000007e /* PORT0_STATUS */ + 0x94 0x0000007e /* PORT6_STATUS */ + >; + }; +}; + +&pinmux { + pmx_led_wan_lan: pinmux_led_wan_lan { + pinctrl-single,bits = <0x10 0x2c2d0000 0xffff0000>, + <0x14 0x292a2b 0xffffff>; + }; +}; + +&builtin_switch { + pinctrl-names = "default"; + pinctrl-0 = <&pmx_led_wan_lan>; + + /delete-property/qca,phy4-mii-enable; +}; + +ð1 { + status = "okay"; + + nvmem-cells = <&macaddr_art_6>; + nvmem-cell-names = "mac-address"; + + gmac-config { + device = <&gmac>; + switch-phy-swap = <0>; + switch-only-mode = <1>; + }; +}; + +&pcie { + status = "okay"; + + ath9k: wifi@0,0 { + compatible = "pci168c,0030"; + reg = <0x0000 0 0 0 0>; + qca,no-eeprom; + qca,disable-2ghz; + #gpio-cells = <2>; + gpio-controller; + }; +}; + +&wmac { + status = "okay"; + + mtd-cal-data = <&art 0x1000>; +}; + +&usb { + status = "okay"; + + #address-cells = <1>; + #size-cells = <0>; + + hub_port1: port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; +}; + +&usb_phy { + status = "okay"; +}; + +&art { + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_art_0: macaddr@0 { + reg = <0x0 0x6>; + }; + + macaddr_art_6: macaddr@6 { + reg = <0x6 0x6>; + }; +}; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index fba6d56674..d37fa4ba2b 100644 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -116,6 +116,12 @@ ath79_setup_interfaces() ubnt,unifi-ap-outdoor-plus) ucidef_set_interface_lan "eth0 eth1" ;; + atheros,db120) + ucidef_add_switch "switch0" \ + "0@eth0" "2:lan" "3:lan" "4:lan" "5:lan" "1:wan" + ucidef_add_switch "switch1" \ + "0@eth1" "1:lan" "2:lan" "3:lan" "4:lan" "5:lan" + ;; avm,fritz4020|\ pcs,cr3000|\ tplink,archer-c58-v1|\ diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom index 388f477856..3e02b066a9 100644 --- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom +++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom @@ -72,6 +72,21 @@ case "$FIRMWARE" in ;; "ath9k-eeprom-pci-0000:00:00.0.bin") case $board in + atheros,db120|\ + engenius,eap600|\ + engenius,ecb600|\ + mercury,mw4530r-v1|\ + ocedo,raccoon|\ + tplink,tl-wdr3500-v1|\ + tplink,tl-wdr3600-v1|\ + tplink,tl-wdr4300-v1|\ + tplink,tl-wdr4300-v1-il|\ + tplink,tl-wdr4310-v1|\ + tplink,tl-wdr4900-v2|\ + ubnt,unifi-ap-pro|\ + winchannel,wb2000) + caldata_extract "art" 0x5000 0x440 + ;; avm,fritz300e) caldata_extract_reverse "urloader" 0x1541 0x440 ;; @@ -88,20 +103,6 @@ case "$FIRMWARE" in caldata_extract "art" 0x5000 0x440 ath9k_patch_mac $(macaddr_add $(mtd_get_mac_text "mac" 0x18) 1) ;; - engenius,eap600|\ - engenius,ecb600|\ - mercury,mw4530r-v1|\ - ocedo,raccoon|\ - tplink,tl-wdr3500-v1|\ - tplink,tl-wdr3600-v1|\ - tplink,tl-wdr4300-v1|\ - tplink,tl-wdr4300-v1-il|\ - tplink,tl-wdr4310-v1|\ - tplink,tl-wdr4900-v2|\ - ubnt,unifi-ap-pro|\ - winchannel,wb2000) - caldata_extract "art" 0x5000 0x440 - ;; enterasys,ws-ap3705i) caldata_extract "calibrate" 0x5000 0x440 ath9k_patch_mac $(mtd_get_mac_ascii u-boot-env0 RADIOADDR0) diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index 2abe1b7307..4b943ba282 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -330,6 +330,27 @@ define Device/aruba_ap-105 endef TARGET_DEVICES += aruba_ap-105 +define Device/atheros_db120 + SOC := ar9344 + DEVICE_VENDOR := Atheros + DEVICE_MODEL := DB120 + DEVICE_PACKAGES := kmod-usb2 + IMAGE_SIZE := 7808k + SUPPORTED_DEVICES += db120 + LOADER_TYPE := bin + LOADER_FLASH_OFFS := 0x50000 + KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49 + COMPILE := loader-$(1).bin loader-$(1).uImage + COMPILE/loader-$(1).bin := loader-okli-compile + COMPILE/loader-$(1).uImage := append-loader-okli $(1) | pad-to 64k | lzma | \ + uImage lzma + IMAGES += factory.bin + IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \ + append-rootfs | pad-rootfs | check-size | pad-to 6336k | \ + append-loader-okli-uimage $(1) | pad-to 64k +endef +TARGET_DEVICES += atheros_db120 + define Device/avm DEVICE_VENDOR := AVM KERNEL := kernel-bin | append-dtb | lzma | eva-image