From: David Bauer Date: Mon, 18 Feb 2019 22:58:34 +0000 (+0100) Subject: ipq40xx: add support for FritzBox 7530 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=95b0c07a618fe5fd93a26931152ced483bba143b;p=openwrt%2Fstaging%2Fnbd.git ipq40xx: add support for FritzBox 7530 Hardware -------- CPU: Qualcomm IPQ4019 RAM: 256M FLASH: 128M NAND ETH: QCA8075 VDSL: Intel/Lantiq VRX518 PCIe attached currently not supported DECT: Dialog SC14448 currently not supported WiFi2: IPQ4019 2T2R 2SS b/g/n WiFi5: IPQ4019 2T2R 2SS n/ac LED: - Power/DSL green - WLAN green - FON/DECT green - Connect/WPS green - Info green - Info red BTN: - WLAN - FON - WPS/Connect UART: 115200n8 3.3V (located under the Dialog chip) VCC - RX - TX - GND (Square is VCC) Installation ------------ 1. Grab the uboot for the Device from the 'u-boot-fritz7530' subdirectory. Place it in the same directory as the 'eva_ramboot.py' script. It is located in the 'scripts/flashing' subdirectory of the OpenWRT tree. 2. Assign yourself the IP address 192.168.178.10/24. Connect your Computer to one of the boxes LAN ports. 3. Connect Power to the Box. As soon as the LAN port of your computer shows link, load the U-Boot to the box using following command. > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz7530.bin 4. The U-Boot will now start. Now assign yourself the IP address 192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP server root directory and rename it to 'FRITZ7530.bin'. 5. The Box will now boot OpenWRT from RAM. This can take up to two minutes. 6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using scp. SSH into the Box and first write the Bootloader to both previous kernel partitions. > mtd write /path/to/uboot-fritz7530.bin uboot0 > mtd write /path/to/uboot-fritz7530.bin uboot1 7. Remove the AVM filesystem partitions to make room for our kernel + rootfs + overlayfs. > ubirmvol /dev/ubi0 --name=avm_filesys_0 > ubirmvol /dev/ubi0 --name=avm_filesys_1 8. Flash OpenWRT peristently using sysupgrade. > sysupgrade -n /path/to/openwrt-sysupgrade.bin Signed-off-by: David Bauer [removed pcie-dts range node, refreshed on top of AP120-AC/E2600AC] Signed-off-by: Christian Lamparter --- diff --git a/package/boot/uboot-fritz4040/Makefile b/package/boot/uboot-fritz4040/Makefile index 36ee0be0af..9af09afcd1 100644 --- a/package/boot/uboot-fritz4040/Makefile +++ b/package/boot/uboot-fritz4040/Makefile @@ -30,6 +30,11 @@ define U-Boot/fritz4040 BUILD_DEVICES:=avm_fritzbox-4040 endef +define U-Boot/fritz7530 + NAME:=FritzBox 7530 + BUILD_DEVICES:=avm_fritzbox-7530 +endef + UBOOT_CONFIGURE_VARS += USE_PRIVATE_LIBGCC=yes UBOOT_MAKE_FLAGS = USE_PRIVATE_LIBGCC=yes export DTC @@ -56,6 +61,6 @@ define Package/u-boot/install $(INSTALL_BIN) $(PKG_BUILD_DIR)/upload-to-f4040.sh $(1)/ endef -UBOOT_TARGETS := fritz4040 +UBOOT_TARGETS := fritz4040 fritz7530 $(eval $(call BuildPackage/U-Boot)) diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile index 62f54fcd7f..9a00832ca2 100644 --- a/package/firmware/ipq-wifi/Makefile +++ b/package/firmware/ipq-wifi/Makefile @@ -18,7 +18,7 @@ endef # Please send a mail with your device-specific board files upstream. # You can find instructions and examples on the linux-wireless wiki: # -ALLWIFIBOARDS:=alfa-network_ap120c-ac asus_map-ac2200 engenius_eap1300 linksys_ea6350v3 qxwlan_e2600ac +ALLWIFIBOARDS:=alfa-network_ap120c-ac asus_map-ac2200 avm_fritzbox-7530 engenius_eap1300 linksys_ea6350v3 qxwlan_e2600ac ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD)) define Package/ipq-wifi-default @@ -56,6 +56,7 @@ endef $(eval $(call generate-ipq-wifi-package,alfa-network_ap120c-ac,board-alfa-network_ap120c-ac.bin,ALFA Network AP120C-AC)) $(eval $(call generate-ipq-wifi-package,asus_map-ac2200,board-map-ac2200.bin,ASUS MAP-AC2200)) $(eval $(call generate-ipq-wifi-package,engenius_eap1300,board-engenius_eap1300.bin,EnGenius EAP1300)) +$(eval $(call generate-ipq-wifi-package,avm_fritzbox-7530,board-avm_fritzbox-7530.bin,AVM FRITZ!Box 7530)) $(eval $(call generate-ipq-wifi-package,linksys_ea6350v3,board-linksys_ea6350v3.bin,Linksys EA6350v3)) $(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac,board-qxwlan-e2600ac.bin,Qxwlan E2600AC)) diff --git a/package/firmware/ipq-wifi/board-avm_fritzbox-7530.bin b/package/firmware/ipq-wifi/board-avm_fritzbox-7530.bin new file mode 100644 index 0000000000..905145f1da Binary files /dev/null and b/package/firmware/ipq-wifi/board-avm_fritzbox-7530.bin differ diff --git a/target/linux/ipq40xx/base-files/etc/board.d/01_leds b/target/linux/ipq40xx/base-files/etc/board.d/01_leds index d23791eab1..dc656cb6ee 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/01_leds +++ b/target/linux/ipq40xx/base-files/etc/board.d/01_leds @@ -25,15 +25,16 @@ avm,fritzbox-4040) ucidef_set_led_netdev "wan" "WAN" "fritz4040:green:wan" "eth1" ucidef_set_led_switch "lan" "LAN" "fritz4040:green:lan" "switch0" "0x1e" ;; +avm,fritzbox-7530 |\ +glinet,gl-b1300) + ucidef_set_led_wlan "wlan" "WLAN" "${boardname}:green:wlan" "phy0tpt" + ;; engenius,eap1300) ucidef_set_led_netdev "lan" "LAN" "${boardname}:blue:lan" "eth0" ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:blue:wlan2g" "phy0tpt" ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:yellow:wlan5g" "phy1tpt" ucidef_set_led_default "mesh" "MESH" "${boardname}:blue:mesh" "0" ;; -glinet,gl-b1300) - ucidef_set_led_wlan "wlan" "WLAN" "${boardname}:green:wlan" "phy0tpt" - ;; netgear,ex6100v2 |\ netgear,ex6150v2) ucidef_set_led_wlan "wlan2g" "WLAN2G" "ex61x0v2:green:router" "phy0tpt" diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index c0466ba8bc..9c232d49f7 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -33,6 +33,10 @@ ipq40xx_setup_interfaces() ucidef_add_switch "switch0" \ "0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan" ;; + avm,fritzbox-7530) + ucidef_add_switch "switch0" \ + "0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan" + ;; compex,wpj428) ucidef_set_interface_lan "eth0 eth1" ;; diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 44421527d2..1264d2ef36 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -135,6 +135,10 @@ case "$FIRMWARE" in avm,fritzbox-4040) /usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config") ;; + avm,fritzbox-7530) + /usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \ + /usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") + ;; compex,wpj428 |\ engenius,eap1300 |\ openmesh,a42 |\ @@ -179,6 +183,10 @@ case "$FIRMWARE" in avm,fritzbox-4040) /usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config") ;; + avm,fritzbox-7530) + /usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \ + /usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") + ;; compex,wpj428 |\ engenius,eap1300 |\ openmesh,a42 |\ diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh index 87e27aff8f..9a2c13cf4d 100644 --- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh @@ -48,6 +48,7 @@ platform_do_upgrade() { case "$(board_name)" in 8dev,jalapeno |\ alfa-network,ap120c-ac |\ + avm,fritzbox-7530 |\ qxwlan,e2600ac-c2) nand_do_upgrade "$ARGV" ;; diff --git a/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-fritzbox-7530.dts b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-fritzbox-7530.dts new file mode 100644 index 0000000000..45c4864855 --- /dev/null +++ b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-fritzbox-7530.dts @@ -0,0 +1,300 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qcom-ipq4019.dtsi" +#include +#include +#include + +/ { + model = "AVM FRITZ!Box 7530"; + compatible = "avm,fritzbox-7530"; + + aliases { + led-boot = &power_green; + led-failsafe = &info_red; + led-running = &power_green; + led-upgrade = &info_green; + }; + + soc { + mdio@90000 { + status = "okay"; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = ; + }; + + tcsr@194b000 { + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = ; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = ; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = ; + }; + + usb3@8af8800 { + status = "okay"; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + watchdog@b017000 { + status = "okay"; + }; + + ess-switch@c000000 { + status = "okay"; + }; + + edma@c080000 { + status = "okay"; + qcom,num_gmac = <1>; + }; + }; + + keys { + compatible = "gpio-keys"; + + wlan { + label = "wlan"; + gpios = <&tlmm 42 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&tlmm 41 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + dect { + label = "dect"; + gpios = <&tlmm 43 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + info_red: info_red { + label = "fritzbox-7530:red:info"; + gpios = <&tlmm 32 GPIO_ACTIVE_LOW>; + }; + + info_green: info { + label = "fritzbox-7530:green:info"; + gpios = <&tlmm 33 GPIO_ACTIVE_LOW>; + }; + + wlan { + label = "fritzbox-7530:green:wlan"; + gpios = <&tlmm 34 GPIO_ACTIVE_LOW>; + }; + + fon { + label = "fritzbox-7530:green:fon"; + gpios = <&tlmm 35 GPIO_ACTIVE_LOW>; + }; + + power_green: power { + label = "fritzbox-7530:green:power"; + gpios = <&tlmm 39 GPIO_ACTIVE_LOW>; + }; + + wps { + label = "fritzbox-7530:green:wps"; + gpios = <&tlmm 45 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&tlmm { + serial_0_pins: serial_pinmux { + mux { + pins = "gpio16", "gpio17"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + nand_pins: nand_pins { + pullups { + pins = "gpio53", "gpio58", "gpio59"; + function = "qpic"; + bias-pull-up; + }; + + pulldowns { + pins = "gpio54", "gpio55", "gpio56", + "gpio57", "gpio60", "gpio61", + "gpio62", "gpio63", "gpio64", + "gpio65", "gpio66", "gpio67", + "gpio68", "gpio69"; + function = "qpic"; + bias-pull-down; + }; + }; + + usb-power { + line-name = "enable USB3 power"; + gpios = <49 GPIO_ACTIVE_HIGH>; + gpio-hog; + output-high; + }; +}; + +&nand { + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + status = "okay"; + cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>; + + nand@0 { + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "SBL1"; + reg = <0x000000 0x80000>; + read-only; + }; + + partition@80000 { + label = "MIBIB"; + reg = <0x080000 0x80000>; + read-only; + }; + + partition@100000 { + label = "QSEE"; + reg = <0x100000 0x80000>; + read-only; + }; + + partition@180000 { + label = "CDT"; + reg = <0x180000 0x40000>; + read-only; + }; + + partition@1c0000 { + label = "QSEE_B"; + reg = <0x1c0000 0x80000>; + read-only; + }; + + partition@240000 { + label = "urlader0"; + reg = <0x240000 0x40000>; + read-only; + }; + + partition@280000 { + label = "urlader1"; + reg = <0x280000 0x40000>; + read-only; + }; + + partition@2c0000 { + label = "nand-tffs"; + reg = <0x2c0000 0x840000>; + read-only; + }; + + partition@b00000 { + /* 'kernel1' in AVM firmware */ + label = "uboot0"; + reg = <0xb00000 0x400000>; + }; + + partition@f00000 { + /* 'kernel2' in AVM firmware */ + label = "uboot1"; + reg = <0xf00000 0x400000>; + }; + + partition@1300000 { + label = "ubi"; + reg = <0x1300000 0x6d00000>; + }; + }; + }; +}; + +&cryptobam { + status = "okay"; +}; + +&blsp_dma { + status = "okay"; +}; + +&blsp1_uart1 { + pinctrl-0 = <&serial_0_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&usb3_ss_phy { + status = "okay"; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&qpic_bam { + status = "okay"; +}; + +&wifi0 { + status = "okay"; + qcom,ath10k-calibration-variant = "AVM-FRITZBox-7530"; +}; + +&wifi1 { + status = "okay"; + qcom,ath10k-calibration-variant = "AVM-FRITZBox-7530"; +}; + +&pcie0 { + status = "okay"; + + perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>; + wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>; + + bridge@0,0 { + reg = <0x00000000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + ranges; + + dsl@1,0 { + compatible = "intel,vrx518"; + status = "okay"; + reg = <0x00010000 0 0 0 0>; + }; + }; +}; diff --git a/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-fritzbox-7530.dts b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-fritzbox-7530.dts new file mode 100644 index 0000000000..53f83f411b --- /dev/null +++ b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-fritzbox-7530.dts @@ -0,0 +1,304 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qcom-ipq4019.dtsi" +#include +#include +#include + +/ { + model = "AVM FRITZ!Box 7530"; + compatible = "avm,fritzbox-7530"; + + aliases { + led-boot = &power_green; + led-failsafe = &info_red; + led-running = &power_green; + led-upgrade = &info_green; + }; + + soc { + rng@22000 { + status = "okay"; + }; + + mdio@90000 { + status = "okay"; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = ; + }; + + tcsr@194b000 { + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = ; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = ; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = ; + }; + + usb3@8af8800 { + status = "okay"; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + watchdog@b017000 { + status = "okay"; + }; + + ess-switch@c000000 { + status = "okay"; + }; + + edma@c080000 { + status = "okay"; + qcom,num_gmac = <1>; + }; + }; + + keys { + compatible = "gpio-keys"; + + wlan { + label = "wlan"; + gpios = <&tlmm 42 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&tlmm 41 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + dect { + label = "dect"; + gpios = <&tlmm 43 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + info_red: info_red { + label = "fritzbox-7530:red:info"; + gpios = <&tlmm 32 GPIO_ACTIVE_LOW>; + }; + + info_green: info { + label = "fritzbox-7530:green:info"; + gpios = <&tlmm 33 GPIO_ACTIVE_LOW>; + }; + + wlan { + label = "fritzbox-7530:green:wlan"; + gpios = <&tlmm 34 GPIO_ACTIVE_LOW>; + }; + + fon { + label = "fritzbox-7530:green:fon"; + gpios = <&tlmm 35 GPIO_ACTIVE_LOW>; + }; + + power_green: power { + label = "fritzbox-7530:green:power"; + gpios = <&tlmm 39 GPIO_ACTIVE_LOW>; + }; + + wps { + label = "fritzbox-7530:green:wps"; + gpios = <&tlmm 45 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&tlmm { + serial_0_pins: serial_pinmux { + mux { + pins = "gpio16", "gpio17"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + nand_pins: nand_pins { + pullups { + pins = "gpio53", "gpio58", "gpio59"; + function = "qpic"; + bias-pull-up; + }; + + pulldowns { + pins = "gpio54", "gpio55", "gpio56", + "gpio57", "gpio60", "gpio61", + "gpio62", "gpio63", "gpio64", + "gpio65", "gpio66", "gpio67", + "gpio68", "gpio69"; + function = "qpic"; + bias-pull-down; + }; + }; + + usb-power { + line-name = "enable USB3 power"; + gpios = <49 GPIO_ACTIVE_HIGH>; + gpio-hog; + output-high; + }; +}; + +&nand { + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + status = "okay"; + cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>; + + nand@0 { + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "SBL1"; + reg = <0x000000 0x80000>; + read-only; + }; + + partition@80000 { + label = "MIBIB"; + reg = <0x080000 0x80000>; + read-only; + }; + + partition@100000 { + label = "QSEE"; + reg = <0x100000 0x80000>; + read-only; + }; + + partition@180000 { + label = "CDT"; + reg = <0x180000 0x40000>; + read-only; + }; + + partition@1c0000 { + label = "QSEE_B"; + reg = <0x1c0000 0x80000>; + read-only; + }; + + partition@240000 { + label = "urlader0"; + reg = <0x240000 0x40000>; + read-only; + }; + + partition@280000 { + label = "urlader1"; + reg = <0x280000 0x40000>; + read-only; + }; + + partition@2c0000 { + label = "nand-tffs"; + reg = <0x2c0000 0x840000>; + read-only; + }; + + partition@b00000 { + /* 'kernel1' in AVM firmware */ + label = "uboot0"; + reg = <0xb00000 0x400000>; + }; + + partition@f00000 { + /* 'kernel2' in AVM firmware */ + label = "uboot1"; + reg = <0xf00000 0x400000>; + }; + + partition@1300000 { + label = "ubi"; + reg = <0x1300000 0x6d00000>; + }; + }; + }; +}; + +&cryptobam { + status = "okay"; +}; + +&blsp_dma { + status = "okay"; +}; + +&blsp1_uart1 { + pinctrl-0 = <&serial_0_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&usb3_ss_phy { + status = "okay"; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&qpic_bam { + status = "okay"; +}; + +&wifi0 { + status = "okay"; + qcom,ath10k-calibration-variant = "AVM-FRITZBox-7530"; +}; + +&wifi1 { + status = "okay"; + qcom,ath10k-calibration-variant = "AVM-FRITZBox-7530"; +}; + +&pcie0 { + status = "okay"; + + perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>; + wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>; + + bridge@0,0 { + reg = <0x00000000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + ranges; + + dsl@1,0 { + compatible = "intel,vrx518"; + status = "okay"; + reg = <0x00010000 0 0 0 0>; + }; + }; +}; diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile index 22836be1fb..3a7ecf39eb 100644 --- a/target/linux/ipq40xx/image/Makefile +++ b/target/linux/ipq40xx/image/Makefile @@ -121,6 +121,15 @@ define Device/avm_fritzbox-4040 endef TARGET_DEVICES += avm_fritzbox-4040 +define Device/avm_fritzbox-7530 + $(call Device/FitImageLzma) + DEVICE_DTS := qcom-ipq4019-fritzbox-7530 + DEVICE_TITLE := AVM Fritz!Box 7530 + DEVICE_PACKAGES := fritz-caldata ipq-wifi-avm_fritzbox-7530 + IMAGES := sysupgrade.bin +endef +TARGET_DEVICES += avm_fritzbox-7530 + define Device/compex_wpj428 $(call Device/FitImage) DEVICE_DTS := qcom-ipq4028-wpj428 diff --git a/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch index 5aeb3963f7..89ce5b1538 100644 --- a/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -697,7 +697,26 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -697,7 +697,27 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -28,6 +28,7 @@ Signed-off-by: John Crispin qcom-ipq4019-ap.dk01.1-c1.dtb \ + qcom-ipq4019-a62.dtb \ + qcom-ipq4019-ap.dk04.1-c1.dtb \ ++ qcom-ipq4019-fritzbox-7530.dtb \ + qcom-ipq4019-map-ac2200.dtb \ + qcom-ipq4019-qxwlan-e2600ac-c1.dtb \ + qcom-ipq4019-qxwlan-e2600ac-c2.dtb \ diff --git a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch index bceadc50e8..f47b7b6dab 100644 --- a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -785,11 +785,29 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -785,11 +785,30 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -31,6 +31,7 @@ Signed-off-by: John Crispin qcom-ipq4019-ap.dk07.1-c1.dtb \ qcom-ipq4019-ap.dk07.1-c2.dtb \ + qcom-ipq4019-a62.dtb \ ++ qcom-ipq4019-fritzbox-7530.dtb \ + qcom-ipq4019-map-ac2200.dtb \ + qcom-ipq4019-qxwlan-e2600ac-c1.dtb \ + qcom-ipq4019-qxwlan-e2600ac-c2.dtb \