From: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Date: Sat, 18 Jan 2020 17:58:10 +0000 (+0100)
Subject: ath79: use rssihigh LED instead of WAN LED for status indication
X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=95731763002fff9c82b734f09bc34eb797af5bf2;p=openwrt%2Fstaging%2Fynezz.git

ath79: use rssihigh LED instead of WAN LED for status indication

Using the LED of network interfaces for status (boot/failsafe/...)
indication is somewhat misleading, as the blinking might be
mistaken for network activity. This uses rssi LEDs instead, which
do not blink normally and thus are less ambiguous.

The rssihigh LED has also been used consistently for the TP-Link CPE
devices.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
---

diff --git a/target/linux/ath79/dts/ar9344_comfast_cf-e120a-v3.dts b/target/linux/ath79/dts/ar9344_comfast_cf-e120a-v3.dts
index 66ac718264..b4a5bb4709 100644
--- a/target/linux/ath79/dts/ar9344_comfast_cf-e120a-v3.dts
+++ b/target/linux/ath79/dts/ar9344_comfast_cf-e120a-v3.dts
@@ -12,9 +12,9 @@
 
 	aliases {
 		serial0 = &uart;
-		led-boot = &led_wan;
-		led-failsafe = &led_wan;
-		led-upgrade = &led_wan;
+		led-boot = &led_rssihigh;
+		led-failsafe = &led_rssihigh;
+		led-upgrade = &led_rssihigh;
 		label-mac-device = &eth0;
 	};
 
@@ -24,7 +24,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&led_rssimediumhigh_pin>;
 
-		led_wan: wan {
+		wan {
 			label = "cf-e120a-v3:green:wan";
 			gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
 		};
@@ -55,7 +55,7 @@
 			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
 		};
 
-		rssihigh {
+		led_rssihigh: rssihigh {
 			label = "cf-e120a-v3:green:rssihigh";
 			gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
 		};
diff --git a/target/linux/ath79/dts/qca9533_comfast_cf-e110n-v2.dts b/target/linux/ath79/dts/qca9533_comfast_cf-e110n-v2.dts
index 0d01342685..45e3727daa 100644
--- a/target/linux/ath79/dts/qca9533_comfast_cf-e110n-v2.dts
+++ b/target/linux/ath79/dts/qca9533_comfast_cf-e110n-v2.dts
@@ -12,9 +12,9 @@
 
 	aliases {
 		serial0 = &uart;
-		led-boot = &led_wan;
-		led-failsafe = &led_wan;
-		led-upgrade = &led_wan;
+		led-boot = &led_rssihigh;
+		led-failsafe = &led_rssihigh;
+		led-upgrade = &led_rssihigh;
 	};
 
 	leds {
@@ -23,7 +23,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&jtag_disable_pins &led_rssilow_pin &led_rssimediumhigh_pin &led_rssihigh_pin>;
 
-		led_wan: wan {
+		wan {
 			label = "cf-e110n-v2:green:wan";
 			gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
 		};
@@ -48,7 +48,7 @@
 			gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
 		};
 
-		rssihigh {
+		led_rssihigh: rssihigh {
 			label = "cf-e110n-v2:green:rssihigh";
 			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
 		};