From: INAGAKI Hiroshi Date: Thu, 22 Feb 2024 10:00:57 +0000 (+0900) Subject: ath79: add support for ELECOM WAB-S1167-PS X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=8e72fa8b6fd46025f4f4eeb1b6e4d7a8aa86881b;p=openwrt%2Fstaging%2Fstintel.git ath79: add support for ELECOM WAB-S1167-PS ELECOM WAB-S1167-PS is a 2.4/5 GHz band 11ac (Wi-Fi 5) access point, based on QCA9557. Specification: - SoC : Qualcomm Atheros QCA9557 - RAM : DDR2 128 MiB (2x Winbond W9751G6KB251) - Flash : SPI-NOR 16 MiB (Macronix MX25L12835FMI-10G) - WLAN : 2.4/5 GHz 2T2R - 2.4 GHz : Qualcomm Atheros QCA9557 (SoC) - 5 GHz : Qualcomm Atheros QCA9882 - Ethernet : 2x 10/100/1000 Mbps - phy ("PD") : Atheros AR8035 - phy ("PSE") : Atheros AR8033 - LEDs/keys (GPIO) : 3x/3x - UART : 1x RJ-45 port - "SERVICE" : TTL (3.3V) - port : ttyS0 - assignment : 1:3.3V, 2:GND, 3:TX, 4:RX - settings : 115200n8 - note : no compatibility with "Cisco console cable" - Buzzer : 1x GPIO-controlled - USB : 1x USB 2.0 Type-A - Power : DC jack or PoE - DC jack : 12 VDC, 1 A (device only, rating) - PoE : 802.3af/at, 48 VDC, 0.25 A (device only, rating) - note : supports 802.3af supply on PSE (downstream) port when powered by DC adapter or 802.3at PoE Flash instruction using factory.bin image: 1. Boot WAB-S1167-PS without no upstream connection (or PoE connection without DHCP) 2. Access to the WebUI ("http://192.168.3.1") on the device and open firmware update page ("ツールボックス" -> "ファームウェア更新") 3. Select the OpenWrt factory.bin image and click update ("アップデート") button 4. Wait ~120 seconds to complete flashing Revert to OEM firmware: 1. Download the latest OEM firmware 2. Remove 128 bytes(0x80) header from firmware image 3. Decode by xor with a pattern "8844a2d168b45a2d" (hex val) 4. Upload the decoded firmware to the device 5. Flash to "firmware" partition by mtd command 6. Reboot Notes: - To use the "SERVICE" port, the connection of 3.3V line is also required to enable console output. The uart line of "SERVICE" is branched out from the internal pin header with 74HC126D and 3.3V line is connected to OE pin on it. - The same PCB is used with WAB-S600-PS. - To supply 802.3af PoE on "PSE" port when powered by DC adapter, 12 VDC 3.5 A adapter is recommended. (official: WAB-EX-ADP1) MAC addresses: Ethernet (PD, PSE): 00:90:FE:xx:xx:04 (Config, ethaddr (text)) 2.4GHz : 00:90:FE:xx:xx:04 (Config, ethaddr (text)) 5GHz : 00:90:FE:xx:xx:05 Signed-off-by: INAGAKI Hiroshi --- diff --git a/target/linux/ath79/dts/qca9557_elecom_wab-s1167-ps.dts b/target/linux/ath79/dts/qca9557_elecom_wab-s1167-ps.dts new file mode 100644 index 0000000000..facead974d --- /dev/null +++ b/target/linux/ath79/dts/qca9557_elecom_wab-s1167-ps.dts @@ -0,0 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qca955x_elecom_wab.dtsi" + +/ { + compatible = "elecom,wab-s1167-ps", "qca,qca9557"; + model = "ELECOM WAB-S1167-PS"; +}; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index 56ef7dd51f..fd7feb1ae5 100644 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -144,6 +144,7 @@ ath79_setup_interfaces() alfa-network,n5q|\ devolo,dvl1200e|\ devolo,dvl1750e|\ + elecom,wab-s1167-ps|\ elecom,wab-s600-ps|\ engenius,enstationac-v1|\ engenius,ews511ap|\ @@ -703,6 +704,7 @@ ath79_setup_macs() lan_mac=$(mtd_get_mac_ascii devdata "lanmac") wan_mac=$(mtd_get_mac_ascii devdata "wanmac") ;; + elecom,wab-s1167-ps|\ elecom,wab-s600-ps|\ engenius,ecb1200|\ engenius,ecb1750) diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac b/target/linux/ath79/generic/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac index 3d24a4f31a..b238fc081e 100644 --- a/target/linux/ath79/generic/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac +++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac @@ -41,6 +41,7 @@ case "$board" in [ "$PHYNBR" -eq 1 ] && \ mtd_get_mac_ascii bdcfg "wlanmac" > /sys${DEVPATH}/macaddress ;; + elecom,wab-s1167-ps|\ elecom,wab-s600-ps) # set the 5G MAC address (= ethaddr + 1) [ "$PHYNBR" -eq 0 ] && \ diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index 16ef4fdca3..7a2b54ddfb 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -1327,6 +1327,14 @@ define Device/elecom_wab kmod-usb2 kmod-usb-ledtrig-usbport endef +define Device/elecom_wab-s1167-ps + $(Device/elecom_wab) + SOC := qca9557 + DEVICE_MODEL := WAB-S1167-PS + ELECOM_HWID := 0107000c +endef +TARGET_DEVICES += elecom_wab-s1167-ps + define Device/elecom_wab-s600-ps $(Device/elecom_wab) SOC := qca9557