From: Maxim Anisimov Date: Wed, 18 Dec 2019 06:52:44 +0000 (+0300) Subject: ramips: add support for TP-Link Archer C20 v5 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=86e7353bff2a5de257de8ec62e782f016eed143c;p=openwrt%2Fstaging%2Fluka.git ramips: add support for TP-Link Archer C20 v5 TP-Link Archer C20 v5 is a router with 5-port FE switch and non-detachable antennas. It's based on MediaTek MT7628N+MT7610EN. Specification: - MediaTek MT7628N/N (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 1T1R 5 GHz - 5x 10/100 Mbps Ethernet - 3x external, non-detachable antennas - UART (J1) header on PCB (115200 8n1) - 7x LED (GPIO-controlled*), 2x button, power input switch * WAN LED in this devices is a dual-color, dual-leads type which isn't (fully) supported by gpio-leds driver. This type of LED requires both GPIOs state change at the same time to select color or turn it off. For now, we support/use only the green part of the LED. Create Factory image -------------------- As all installation methods require a U-Boot to be integrated into the Image (and we do not ship one with the image) we are not able to create an image in the OpenWRT build-process. Download a TP-Link image from their Website and a OpenWRT sysupgrade image for the device and build yourself a factory image like following: TP-Link image: tpl.bin OpenWRT sysupgrade image: owrt.bin > dd if=tpl.bin of=boot.bin bs=131584 count=1 > cat owrt.bin >> boot.bin Installing via Web-UI --------------------- Upload the boot.bin via TP-Links firmware upgrade tool in the web-interface. Installing via Recovery ----------------------- Activate Web-Recovery by beginning the upgrade Process with a Firmware-Image from TP-Link. After starting the Firmware Upgrade, wait ~3 seconds (When update status is switching to 0%), then disconnect the power supply from the device. Upgrade flag (which activates Web-Recovery) is written before the OS-image is touched and removed after write is succesfull, so this procedure should be safe. Plug the power back in. It will come up in Recovery-Mode on 192.168.0.1. When active, all LEDs but the WPS LED are off. Remeber to assign yourself a static IP-address as DHCP is not active in this mode. The boot.bin can now be uploaded and flashed using the web-recovery. Installing via TFTP ------------------- Prepare an image like following (Filenames from factory image steps apply here) > dd if=/dev/zero of=tp_recovery.bin bs=196608 count=1 > dd if=tpl.bin of=tmp.bin bs=131584 count=1 > dd if=tmp.bin of=boot.bin bs=512 skip=1 > cat boot.bin >> tp_recovery.bin > cat owrt.bin >> tp_recovery.bin Place tp_recovery.bin in root directory of TFTP server and listen on 192.168.0.66/24. Connect router LAN ports with your computer and power up the router while pressing the reset button. The router will download the image via tftp and after ~1 Minute reboot into OpenWRT. U-Boot CLI ---------- U-Boot CLI can be activated by holding down '4' on bootup. Dual U-Boot ----------- This is TP-Link MediaTek device with a split-uboot feature design like a TP-Link Archer C50 v4. The first (factory-uboot) provides recovery via TFTP and HTTP, jumping straight into the second (firmware-uboot) if no recovery needs to be performed. The firmware-uboot unpacks and executed the kernel. Web-Recovery ------------ TP-Link integrated a new Web-Recovery like the one on the Archer C7v4 / TL-WR1043v5 / Archer C50v4. Stock-firmware sets a flag in the "romfile" partition before beginning to write and removes it afterwards. If the router boots with this flag set, bootloader will automatically start Web-recovery and listens on 192.168.0.1. This way, the vendor-firmware or an OpenWRT factory image can be written. By doing the same while performing sysupgrade, we can take advantage of the Web-recovery in OpenWRT. It is important to note that Web-Recovery is only based on this flag. It can't detect e.g. a crashing kernel or other means. Once activated it won't boot the OS before a recovery action (either via TFTP or HTTP) is performed. This recovery-mode is indicated by an illuminated WPS-LED on boot. Signed-off-by: Maxim Anisimov [adjust some node names for LEDs in DTS] Signed-off-by: Adrian Schmutzler --- diff --git a/target/linux/ramips/dts/mt7628an_tplink_archer-c20-v5.dts b/target/linux/ramips/dts/mt7628an_tplink_archer-c20-v5.dts new file mode 100644 index 0000000000..e01826841d --- /dev/null +++ b/target/linux/ramips/dts/mt7628an_tplink_archer-c20-v5.dts @@ -0,0 +1,98 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include "mt7628an_tplink_8m-split-uboot.dtsi" + +#include +#include + +/ { + compatible = "tplink,archer-c20-v5", "mediatek,mt7628an-soc"; + model = "TP-Link Archer C20 v5"; + + aliases { + led-boot = &led_power; + led-failsafe = &led_power; + led-running = &led_power; + led-upgrade = &led_power; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + rfkill { + label = "rfkill"; + gpios = <&gpio1 5 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_power: power { + label = "archer-c20-v5:green:power"; + gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; + }; + + wlan2g { + label = "archer-c20-v5:green:wlan2g"; + gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + wlan5g { + label = "archer-c20-v5:green:wlan5g"; + gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + + lan { + label = "archer-c20-v5:green:lan"; + gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; + }; + + wan_green { + label = "archer-c20-v5:green:wan"; + gpios = <&gpio1 11 GPIO_ACTIVE_LOW>; + }; + + wan_orange { + label = "archer-c20-v5:orange:wan"; + gpios = <&gpio0 11 GPIO_ACTIVE_LOW>; + }; + + wps { + label = "archer-c20-v5:green:wps"; + gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&state_default { + gpio { + ralink,group = "i2s", "gpio", "refclk", "p0led_an", "p1led_an", + "p2led_an", "p3led_an", "p4led_an", "wdt"; + ralink,function = "gpio"; + }; +}; + +&pcie { + status = "okay"; +}; + +&pcie0 { + wifi@0,0 { + reg = <0x0000 0 0 0 0>; + mediatek,mtd-eeprom = <&radio 0x8000>; + ieee80211-freq-limit = <5000000 6000000>; + mtd-mac-address = <&rom 0xf100>; + mtd-mac-address-increment = <(-1)>; + }; +}; diff --git a/target/linux/ramips/image/mt76x8.mk b/target/linux/ramips/image/mt76x8.mk index 2b5ec60a90..f3a948bf11 100644 --- a/target/linux/ramips/image/mt76x8.mk +++ b/target/linux/ramips/image/mt76x8.mk @@ -282,6 +282,21 @@ define Device/tplink_archer-c20-v4 endef TARGET_DEVICES += tplink_archer-c20-v4 +define Device/tplink_archer-c20-v5 + $(Device/tplink) + IMAGE_SIZE := 7616k + DEVICE_MODEL := Archer C20 + DEVICE_VARIANT := v5 + TPLINK_FLASHLAYOUT := 8MSUmtk + TPLINK_HWID := 0xc200005 + TPLINK_HWREV := 0x1 + TPLINK_HWREVADD := 0x5 + TPLINK_HVERSION := 3 + DEVICE_PACKAGES := kmod-mt76x0e + IMAGES := sysupgrade.bin +endef +TARGET_DEVICES += tplink_archer-c20-v5 + define Device/tplink_archer-c50-v3 $(Device/tplink) IMAGE_SIZE := 7808k diff --git a/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds b/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds index 06b78eb195..79f45ba545 100755 --- a/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds @@ -52,7 +52,8 @@ tama,w06) ucidef_set_led_netdev "wan" "WAN" "$boardname:green:wan" "eth0" ucidef_set_led_wlan "wlan" "WLAN" "$boardname:green:wlan" "phy0tpt" ;; -tplink,archer-c20-v4) +tplink,archer-c20-v4|\ +tplink,archer-c20-v5) ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch0" "0x1e" ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x01" ;; diff --git a/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network b/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network index a733353f71..646e29235c 100755 --- a/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network +++ b/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network @@ -40,6 +40,7 @@ ramips_setup_interfaces() hiwifi,hc5861b|\ skylab,skw92a|\ tplink,archer-c20-v4|\ + tplink,archer-c20-v5|\ tplink,archer-c50-v3|\ tplink,archer-c50-v4|\ tplink,tl-mr3420-v5|\ @@ -191,6 +192,7 @@ ramips_setup_macs() tplink,tl-wr842n-v5) wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 0xf100)" 1) ;; + tplink,archer-c20-v5|\ tplink,archer-c50-v4) wan_mac=$(macaddr_add "$(mtd_get_mac_binary rom 0xf100)" 1) ;; diff --git a/target/linux/ramips/mt76x8/base-files/lib/upgrade/platform.sh b/target/linux/ramips/mt76x8/base-files/lib/upgrade/platform.sh index a3de97abf7..20adfafc3d 100755 --- a/target/linux/ramips/mt76x8/base-files/lib/upgrade/platform.sh +++ b/target/linux/ramips/mt76x8/base-files/lib/upgrade/platform.sh @@ -28,6 +28,7 @@ platform_do_upgrade() { } default_do_upgrade "$1" ;; + tplink,archer-c20-v5|\ tplink,archer-c50-v4) MTD_ARGS="-t romfile" default_do_upgrade "$1"