From: Robert Marko Date: Wed, 9 Feb 2022 07:45:47 +0000 (+0200) Subject: mvebu: add support for RB5009UG+S+IN X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=85d9fd6f0ec776d334871c052f4e15903238d9b4;p=openwrt%2Fstaging%2Fansuel.git mvebu: add support for RB5009UG+S+IN This patch adds support for Mikrotik RB5009UG+S+IN. Specifications: - SoC: Marvell Armada 7040 (88F7040) - 4 cores, ARMv8 Cortex-A72, 1.4GHz, 64bit - RAM: 1024MB DDR4 - Flash: 16MB SPI NOR flash, 1024MB NAND - Ethernet: * Marvell 88E6393X - Amethyst: * one 2.5G RJ45 port via Qualcomm QCA8081 PHY * seven 1G RJ45 ports via built-in PHY-s * one 10G SFP+ cage * All ports share the same 10G switch uplink to the CPU - LED: User, SFP, Hdr1, Hdr2 - Buttons: Reset - UART: 115200 8n1 on the MikroTik 16 pin header - USB: One USB3 port - Power: 24-57 V via * DC jack * 802.3af/at PoE on Ethernet 1 * 2-pin terminal on the side 16 Pin header pinout: 1 GND Vcc RX ? GND #--------------------# |.-. .-. .-. .-. .-. | |'-' '-' '-' '-' '-' | |.-. .-. .-. .-. .-. | |'-' '-' '-' '-' '-' | #--------------------# 2 CLK DO /CS TX DI Do note that the default RouterBoot has disabled UART even when the required hard-config bit is set to indicate UART support. Patched RouterBoot must be used if UART is desired. Also, since ARM64 Linux support does not support in any way appending the DTB to the kernel image we use mainline U-Boot with added RB5009 support in order to boot OpenWrt. MikroTik uses YAFFS to store the boot kernel and we use YAFUT to put U-Boot as the kernel which RouterBoot then simply boots as an ELF. Install instructions: NOTE: In case you are using an existing out of tree version of OpenWrt make sure to reinstall RouterOS via Netinstall to return the expected partition layout. 1. Prepare FAT or EXT4 formatted USB drive with OpenWrt initramfs: * Copy bin/targets/mvebu/cortexa72/openwrt-mvebu-cortexa72-mikrotik_rb5009-initramfs-uImage.itb to the root of FAT or EXT4 formatted USB drive. * Plug in the drive to the RB5009 USB port 2. Boot the modified OpenWrt built U-Boot ELF: u-boot.elf from bin/targets/mvebu/cortexa72/u-boot-rb5009/u-boot.elf Consult OpenWrt wiki for common instructions on switching to boot from Ethernet once as well as serving the file: https://openwrt.org/toh/mikrotik/common Once U-Boot is booted it will attempt to boot in the following order: 1. NAND 2. USB 3. Network NAND is expected to fail but USB or Networking need to serve the OpenWrt initramfs image and after booting it will be accessible from LAN ports on the default 192.168.1.1 IP with default credentials. 3. Flash modified RouterBoot that enables UART (Optional but recommended): https://public.robimarko.eu/RB5009/70x0-7.15-uart.fwf * Copy the file over to the booted OpenWrt initramfs to /tmp * Run: mtd erase RouterBOOT-primary * Run: mtd write /tmp/70x0-7.15-uart.fwf RouterBOOT-primary 4. Install U-Boot to boot OpenWrt: * Copy the u-boot.elf from bin/targets/mvebu/cortexa72/u-boot-rb5009/u-boot.elf to OpenWrt initramfs to /tmp. * Run: . /lib/functions.sh * Run: yafut -d /dev/mtd$(find_mtd_index "YAFFS") -w -i /tmp/u-boot.elf -o kernel -T This will use yafut to copy the U-Boot as kernel in YAFFS so that RouterBoot boots it. 5. Wipe the NAND UBI partition: * Run: ubiformat /dev/mtd$(find_mtd_index "ubi") -y This will prepare the existing RouterOS rootfs partition for OpenWrt. 6. Flash OpenWrt: * Copy the bin/targets/mvebu/cortexa72/openwrt-mvebu-cortexa72-mikrotik_rb5009-squashfs-sysupgrade.bin to OpenWrt initramfs to /tmp. * Run: sysupgrade /tmp/openwrt-mvebu-cortexa72-mikrotik_rb5009-squashfs-sysupgrade.bin Device will reboot, boot U-Boot and then OpenWrt. Recovery: In case you need to reinstall OpenWrt if it crashes after U-Boot, there is a recovery mechanism in OpenWrt to boot the OpenWrt initramfs. You need to hold the reset button while U-Boot is booting and then it will boot the OpenWrt initramfs from: 1. USB 2. Networking In recovery mode U-Boot will light all of the LED-s except for the switch ones. In case you want to return to RouterOS, you can simply do that via Netinstall like on any other MikroTik board. Credits also go to Serhii Serhieiev who origininally figured out the RouterBoot modification for UART, the missing 10G MVPP2 support in U-Boot as well as the custom aux loader to boot directly via RouterBoot. Link: https://github.com/openwrt/openwrt/pull/15765 Signed-off-by: Robert Marko --- diff --git a/target/linux/mvebu/cortexa72/base-files/etc/board.d/02_network b/target/linux/mvebu/cortexa72/base-files/etc/board.d/02_network index 93dadf491b..bd77be3d41 100644 --- a/target/linux/mvebu/cortexa72/base-files/etc/board.d/02_network +++ b/target/linux/mvebu/cortexa72/base-files/etc/board.d/02_network @@ -32,6 +32,9 @@ marvell,armada7040-db) marvell,armada8040-clearfog-gt-8k) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 eth2" "eth0 eth1" ;; +mikrotik,rb5009) + ucidef_set_interfaces_lan_wan "p2 p3 p4 p5 p6 p7 p8 sfp" "p1" + ;; solidrun,clearfog-pro) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 lan5 lan6 eth0 eth1" "eth2" ;; diff --git a/target/linux/mvebu/cortexa72/base-files/lib/upgrade/platform.sh b/target/linux/mvebu/cortexa72/base-files/lib/upgrade/platform.sh index c7f20a6d7c..bb81b0ff26 100755 --- a/target/linux/mvebu/cortexa72/base-files/lib/upgrade/platform.sh +++ b/target/linux/mvebu/cortexa72/base-files/lib/upgrade/platform.sh @@ -37,6 +37,9 @@ platform_do_upgrade() { solidrun,clearfog-pro) legacy_sdcard_do_upgrade "$1" ;; + mikrotik,rb5009) + nand_do_upgrade "$1" + ;; *) default_do_upgrade "$1" ;; diff --git a/target/linux/mvebu/cortexa72/config-6.6 b/target/linux/mvebu/cortexa72/config-6.6 index de2cec6f26..19ca2b29d1 100644 --- a/target/linux/mvebu/cortexa72/config-6.6 +++ b/target/linux/mvebu/cortexa72/config-6.6 @@ -102,6 +102,7 @@ CONFIG_QUEUED_SPINLOCKS=y CONFIG_RAS=y # CONFIG_RAVE_SP_CORE is not set CONFIG_REGULATOR_GPIO=y +CONFIG_REGULATOR_USERSPACE_CONSUMER=y # CONFIG_RODATA_FULL_DEFAULT_ENABLED is not set CONFIG_SENSORS_IEI_WT61P803_PUZZLE_HWMON=y CONFIG_SERIAL_DEV_BUS=y diff --git a/target/linux/mvebu/files-6.6/arch/arm64/boot/dts/marvell/armada-7040-rb5009.dts b/target/linux/mvebu/files-6.6/arch/arm64/boot/dts/marvell/armada-7040-rb5009.dts new file mode 100644 index 0000000000..8cd744f64d --- /dev/null +++ b/target/linux/mvebu/files-6.6/arch/arm64/boot/dts/marvell/armada-7040-rb5009.dts @@ -0,0 +1,384 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +/dts-v1/; + +#include "armada-7040.dtsi" +#include +#include + +/ { + model = "MikroTik RB5009"; + compatible = "mikrotik,rb5009", "marvell,armada7040", + "marvell,armada-ap806-quad", "marvell,armada-ap806"; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x40000000>; + }; + + aliases { + led-boot = &led_user; + led-failsafe = &led_user; + led-running = &led_user; + led-upgrade = &led_user; + }; + + usb3_vbus: regulator-usb3-vbus0 { + compatible = "regulator-fixed"; + regulator-name = "usb3_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&cp0_gpio2 23 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_leds: regulator-leds { + compatible = "regulator-fixed"; + regulator-name = "LED-power"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&cp0_gpio2 27 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-boot-on; + }; + + output-led-power { + compatible = "regulator-output"; + vout-supply = <®_leds>; + }; + + sfp_i2c: sfp-i2c { + compatible = "i2c-gpio"; + sda-gpios = <&cp0_gpio1 0 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&cp0_gpio1 1 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&cp0_gpio1 28 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_user: user { + label = "green:user"; + gpios = <&cp0_gpio2 26 GPIO_ACTIVE_LOW>; + }; + + sfp { + label = "green:sfp"; + gpios = <&cp0_gpio2 25 GPIO_ACTIVE_LOW>; + }; + + hdr1 { + label = "blue:hdr1"; + gpios = <&cp0_gpio1 4 GPIO_ACTIVE_LOW>; + }; + + hdr2 { + label = "blue:hdr2"; + gpios = <&cp0_gpio2 19 GPIO_ACTIVE_LOW>; + }; + }; + + sfp: sfp { + compatible = "sff,sfp"; + i2c-bus = <&sfp_i2c>; + mod-def0-gpios = <&cp0_gpio1 11 GPIO_ACTIVE_LOW>; + los-gpios = <&cp0_gpio1 2 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&cp0_gpio1 6 GPIO_ACTIVE_HIGH>; + tx-disable-gpios = <&cp0_gpio1 5 GPIO_ACTIVE_HIGH>; + rate-select0-gpios = <&cp0_gpio1 3 GPIO_ACTIVE_HIGH>; + }; +}; + +&uart0 { + status = "okay"; + + pinctrl-0 = <&uart0_pins>; + pinctrl-names = "default"; +}; + + +&spi0 { + status = "okay"; + + flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <20000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + compatible = "mikrotik,routerboot-partitions"; + #address-cells = <1>; + #size-cells = <1>; + label = "MikroTik"; + reg = <0x0 0xfe0000>; + + hard_config: hard_config { + read-only; + + nvmem-layout { + compatible = "mikrotik,routerboot-nvmem"; + + macaddr_hard: base-mac-address { + #nvmem-cell-cells = <1>; + }; + }; + }; + + soft_config { + }; + + dtb_config { + read-only; + }; + }; + + partition@b0000 { + label = "RouterBOOT-primary"; + reg = <0xb0000 0x10000>; + }; + + /* Empty space on NOR repurposed for U-Boot environment */ + partition@fe0000 { + compatible = "u-boot,env"; + label = "u-boot-env"; + reg = <0xfe0000 0x20000>; + }; + }; + }; +}; + +&cp0_nand_controller { + status = "okay"; + + nand@0 { + reg = <0>; + nand-rb = <0>; + nand-ecc-mode = "hw"; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + nand-on-flash-bbt; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "YAFFS"; + reg = <0x0 0x800000>; + }; + + partition@800000 { + label = "ubi"; + reg = <0x800000 0x3f800000>; + }; + }; + }; +}; + +&cp0_utmi { + status = "okay"; +}; + +&cp0_comphy3 { + connector { + compatible = "usb-a-connector"; + phy-supply = <&usb3_vbus>; + }; +}; + +&cp0_usb3_1 { + status = "okay"; + phys = <&cp0_comphy3 1>, <&cp0_utmi1>; + phy-names = "cp0-usb3h1-comphy", "utmi"; + dr_mode = "host"; +}; + +&cp0_i2c0 { + status = "okay"; + clock-frequency = <100000>; +}; + +&cp0_mdio { + status = "okay"; +}; + +&cp0_ethernet { + status = "okay"; +}; + +&cp0_eth0 { + /* This port is connected to 88E6393X switch */ + status = "okay"; + phy-mode = "10gbase-r"; + phys = <&cp0_comphy2 0>; + managed = "in-band-status"; + nvmem-cells = <&macaddr_hard 0>; + nvmem-cell-names = "mac-address"; +}; + +&cp0_mdio { + status = "okay"; + + switch@0 { + /* Actual device is MV88E6393X */ + compatible = "marvell,mv88e6190"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + /* LED config is lost if switch is reset */ + //reset-gpios = <&cp0_gpio2 2 GPIO_ACTIVE_HIGH>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "cpu"; + ethernet = <&cp0_eth0>; + phy-mode = "10gbase-r"; + managed = "in-band-status"; + }; + + port@1 { + reg = <1>; + label = "p8"; + phy-handle = <&switch0phy1>; + nvmem-cells = <&macaddr_hard 7>; + nvmem-cell-names = "mac-address"; + }; + + port@2 { + reg = <2>; + label = "p7"; + phy-handle = <&switch0phy2>; + nvmem-cells = <&macaddr_hard 6>; + nvmem-cell-names = "mac-address"; + }; + + port@3 { + reg = <3>; + label = "p6"; + phy-handle = <&switch0phy3>; + nvmem-cells = <&macaddr_hard 5>; + nvmem-cell-names = "mac-address"; + }; + + port@4 { + reg = <4>; + label = "p5"; + phy-handle = <&switch0phy4>; + nvmem-cells = <&macaddr_hard 4>; + nvmem-cell-names = "mac-address"; + }; + + port@5 { + reg = <5>; + label = "p4"; + phy-handle = <&switch0phy5>; + nvmem-cells = <&macaddr_hard 3>; + nvmem-cell-names = "mac-address"; + }; + + port@6 { + reg = <6>; + label = "p3"; + phy-handle = <&switch0phy6>; + nvmem-cells = <&macaddr_hard 2>; + nvmem-cell-names = "mac-address"; + }; + + port@7 { + reg = <7>; + label = "p2"; + phy-handle = <&switch0phy7>; + nvmem-cells = <&macaddr_hard 1>; + nvmem-cell-names = "mac-address"; + }; + + port@9 { + reg = <9>; + label = "p1"; + phy-mode = "sgmii"; + phy-handle = <&qca8081>; + managed = "in-band-status"; + nvmem-cells = <&macaddr_hard 0>; + nvmem-cell-names = "mac-address"; + }; + + port@a { + reg = <10>; + label = "sfp"; + phy-mode = "10gbase-r"; + managed = "in-band-status"; + sfp = <&sfp>; + nvmem-cells = <&macaddr_hard 8>; + nvmem-cell-names = "mac-address"; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch0phy1: switch0phy1@1 { + reg = <0x1>; + }; + + switch0phy2: switch0phy2@2 { + reg = <0x2>; + }; + + switch0phy3: switch0phy3@3 { + reg = <0x3>; + }; + + switch0phy4: switch0phy4@4 { + reg = <0x4>; + }; + + switch0phy5: switch0phy5@5 { + reg = <0x5>; + }; + + switch0phy6: switch0phy6@6 { + reg = <0x6>; + }; + + switch0phy7: switch0phy7@7 { + reg = <0x7>; + }; + }; + + mdio1 { + compatible = "marvell,mv88e6xxx-mdio-external"; + #address-cells = <1>; + #size-cells = <0>; + + qca8081: qca8081@0 { + reg = <0>; + }; + }; + }; +}; diff --git a/target/linux/mvebu/image/cortexa72.mk b/target/linux/mvebu/image/cortexa72.mk index 17904dc6c3..48919b7f71 100644 --- a/target/linux/mvebu/image/cortexa72.mk +++ b/target/linux/mvebu/image/cortexa72.mk @@ -1,3 +1,16 @@ +define Device/FitImage + KERNEL_SUFFIX := -uImage.itb + KERNEL = kernel-bin | gzip | fit gzip $$(KDIR)/image-$$(DEVICE_DTS).dtb + KERNEL_NAME := Image +endef + +define Device/UbiFit + KERNEL_IN_UBI := 1 + IMAGES := factory.ubi sysupgrade.bin + IMAGE/factory.ubi := append-ubi + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata +endef + define Device/globalscale_mochabin $(call Device/Default-arm64) DEVICE_VENDOR := Globalscale @@ -52,6 +65,19 @@ define Device/marvell_macchiatobin-singleshot endef TARGET_DEVICES += marvell_macchiatobin-singleshot +define Device/mikrotik_rb5009 + $(call Device/Default-arm64) + $(Device/NAND-128K) + $(call Device/FitImage) + $(call Device/UbiFit) + DEVICE_VENDOR := MikroTik + DEVICE_MODEL := RB5009 + SOC := armada-7040 + KERNEL_LOADADDR := 0x22000000 + DEVICE_PACKAGES += kmod-i2c-gpio yafut +endef +TARGET_DEVICES += mikrotik_rb5009 + define Device/marvell_clearfog-gt-8k $(call Device/Default-arm64) DEVICE_VENDOR := SolidRun