From: Pavel Kubelun Date: Tue, 21 Jun 2016 09:55:00 +0000 (+0200) Subject: ipq806x: add initial support for Netgear R7800 X-Git-Tag: v19.07.0-rc1~9880 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=823242185b56ea518568296f1a5834f736f12076;p=openwrt%2Fstaging%2Fhauke.git ipq806x: add initial support for Netgear R7800 Signed-off-by: Pavel Kubelun --- diff --git a/target/linux/ipq806x/base-files/etc/board.d/01_leds b/target/linux/ipq806x/base-files/etc/board.d/01_leds index 568b4827b7..17f1a28abc 100755 --- a/target/linux/ipq806x/base-files/etc/board.d/01_leds +++ b/target/linux/ipq806x/base-files/etc/board.d/01_leds @@ -19,13 +19,14 @@ c2600) ucidef_set_led_default "general" "general" "ledgnr:blue" "1" ;; d7800 |\ -r7500) - ucidef_set_led_usbdev "usb1" "USB 1" "r7500:white:usb1" "1-1" - ucidef_set_led_usbdev "usb2" "USB 2" "r7500:white:usb3" "3-1" - ucidef_set_led_netdev "wan" "WAN" "r7500:white:wan" "eth0" - ucidef_set_led_ide "esata" "eSATA" "r7500:amber:esata" - ucidef_set_led_default "wps" "WPS" "r7500:white:wps" "0" - ucidef_set_led_default "rfkill" "rfkill" "r7500:white:rfkill" "0" +r7500 |\ +r7800) + ucidef_set_led_usbdev "usb1" "USB 1" "${board}:white:usb1" "1-1" + ucidef_set_led_usbdev "usb2" "USB 2" "${board}:white:usb3" "3-1" + ucidef_set_led_netdev "wan" "WAN" "${board}:white:wan" "eth0" + ucidef_set_led_ide "esata" "eSATA" "${board}:amber:esata" + ucidef_set_led_default "wps" "WPS" "${board}:white:wps" "0" + ucidef_set_led_default "rfkill" "rfkill" "${board}:white:rfkill" "0" ;; ea8500) ucidef_set_led_wlan "wifi" "WIFI" "ea8500:green:wifi" "phy0radio" diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network index 67969669f1..16cc13cfc0 100755 --- a/target/linux/ipq806x/base-files/etc/board.d/02_network +++ b/target/linux/ipq806x/base-files/etc/board.d/02_network @@ -16,7 +16,8 @@ case "$board" in ap148 |\ c2600 |\ d7800 |\ -r7500) +r7500 |\ +r7800) ucidef_add_switch "switch0" \ "1:lan" "2:lan" "3:lan" "4:lan" "6@eth1" "5:wan" "0@eth0" ;; diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 24da5500b5..a23dd80a00 100644 --- a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -56,6 +56,9 @@ case "$FIRMWARE" in hw_mac_addr=$(mtd_get_mac_ascii devinfo hw_mac_addr) ath10kcal_extract "art" 4096 12064 ;; + r7800) + ath10kcal_extract "art" 4096 12064 + ;; esac ;; "ath10k/cal-pci-0001:01:00.0.bin") @@ -68,6 +71,9 @@ case "$FIRMWARE" in hw_mac_addr=$(mtd_get_mac_ascii devinfo hw_mac_addr) ath10kcal_extract "art" 20480 12064 ;; + r7800) + ath10kcal_extract "art" 20480 12064 + ;; esac ;; *) diff --git a/target/linux/ipq806x/base-files/lib/ipq806x.sh b/target/linux/ipq806x/base-files/lib/ipq806x.sh index 8157e6afac..adac916f6b 100644 --- a/target/linux/ipq806x/base-files/lib/ipq806x.sh +++ b/target/linux/ipq806x/base-files/lib/ipq806x.sh @@ -32,6 +32,9 @@ ipq806x_board_detect() { *"Linksys EA8500"*) name="ea8500" ;; + *"R7800") + name="r7800" + ;; esac [ -z "$name" ] && name="unknown" diff --git a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh index 2b6f61d7be..cfd7cd7ed6 100644 --- a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh @@ -9,7 +9,8 @@ platform_check_image() { ap148 |\ d7800 |\ ea8500 |\ - r7500) + r7500 |\ + r7800) nand_do_platform_check $board $1 return $?; ;; @@ -32,7 +33,8 @@ platform_pre_upgrade() { case "$board" in ap148 |\ d7800 |\ - r7500) + r7500 |\ + r7800) nand_do_upgrade "$1" ;; ea8500) diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-r7800.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-r7800.dts new file mode 100644 index 0000000000..498624325d --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-r7800.dts @@ -0,0 +1,372 @@ +#include "qcom-ipq8065-v1.0.dtsi" + +#include + +/ { + model = "Netgear Nighthawk X4S R7800"; + compatible = "netgear,r7800", "qcom,ipq8065"; + + memory@0 { + reg = <0x42000000 0x1e000000>; + device_type = "memory"; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + rsvd@41200000 { + reg = <0x41200000 0x300000>; + no-map; + }; + }; + + aliases { + serial0 = &uart4; + mdio-gpio0 = &mdio0; + }; + + chosen { + bootargs = "rootfstype=squashfs noinitrd"; + linux,stdout-path = "serial0:115200n8"; + }; + + soc { + pinmux@800000 { + i2c4_pins: i2c4_pinmux { + pins = "gpio12", "gpio13"; + function = "gsbi4"; + bias-disable; + }; + + pcie0_pins: pcie0_pinmux { + mux { + pins = "gpio3"; + function = "pcie1_rst"; + drive-strength = <12>; + bias-disable; + }; + }; + + pcie1_pins: pcie1_pinmux { + mux { + pins = "gpio48"; + function = "pcie2_rst"; + drive-strength = <12>; + bias-disable; + }; + }; + + nand_pins: nand_pins { + mux { + pins = "gpio34", "gpio35", "gpio36", + "gpio37", "gpio38", "gpio39", + "gpio40", "gpio41", "gpio42", + "gpio43", "gpio44", "gpio45", + "gpio46", "gpio47"; + function = "nand"; + drive-strength = <10>; + bias-disable; + }; + pullups { + pins = "gpio39"; + bias-pull-up; + }; + hold { + pins = "gpio40", "gpio41", "gpio42", + "gpio43", "gpio44", "gpio45", + "gpio46", "gpio47"; + bias-bus-hold; + }; + }; + + mdio0_pins: mdio0_pins { + mux { + pins = "gpio0", "gpio1"; + function = "gpio"; + drive-strength = <8>; + bias-disable; + }; + }; + + rgmii2_pins: rgmii2_pins { + mux { + pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", + "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; + function = "rgmii2"; + drive-strength = <8>; + bias-disable; + }; + }; + }; + + gsbi@16300000 { + qcom,mode = ; + status = "ok"; + serial@16340000 { + status = "ok"; + }; + /* + * The i2c device on gsbi4 should not be enabled. + * On ipq806x designs gsbi4 i2c is meant for exclusive + * RPM usage. Turning this on in kernel manifests as + * i2c failure for the RPM. + */ + }; + + sata-phy@1b400000 { + status = "ok"; + }; + + sata@29000000 { + status = "ok"; + }; + + phy@100f8800 { /* USB3 port 1 HS phy */ + status = "ok"; + }; + + phy@100f8830 { /* USB3 port 1 SS phy */ + status = "ok"; + }; + + phy@110f8800 { /* USB3 port 0 HS phy */ + status = "ok"; + }; + + phy@110f8830 { /* USB3 port 0 SS phy */ + status = "ok"; + }; + + usb30@0 { + status = "ok"; + }; + + usb30@1 { + status = "ok"; + }; + + pcie0: pci@1b500000 { + status = "ok"; + reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>; + pinctrl-0 = <&pcie0_pins>; + pinctrl-names = "default"; + }; + + pcie1: pci@1b700000 { + status = "ok"; + reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>; + pinctrl-0 = <&pcie1_pins>; + pinctrl-names = "default"; + }; + + nand@1ac00000 { + status = "ok"; + + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + + nand-ecc-strength = <4>; + nand-bus-width = <8>; + + #address-cells = <1>; + #size-cells = <1>; + + qcadata@0 { + label = "qcadata"; + reg = <0x0000000 0x0c80000>; + read-only; + }; + + APPSBL@c80000 { + label = "APPSBL"; + reg = <0x0c80000 0x0500000>; + read-only; + }; + + APPSBLENV@1180000 { + label = "APPSBLENV"; + reg = <0x1180000 0x0080000>; + read-only; + }; + + art: art@1200000 { + label = "art"; + reg = <0x1200000 0x0140000>; + read-only; + }; + + artbak: art@1340000 { + label = "artbak"; + reg = <0x1340000 0x0140000>; + read-only; + }; + + kernel@1480000 { + label = "kernel"; + reg = <0x1480000 0x0200000>; + }; + + ubi@1680000 { + label = "ubi"; + reg = <0x1680000 0x1E00000>; + }; + + netgear@3480000 { + label = "netgear"; + reg = <0x3480000 0x4480000>; + read-only; + }; + + reserve@7900000 { + label = "reserve"; + reg = <0x7900000 0x0700000>; + read-only; + }; + + firmware@1480000 { + label = "firmware"; + reg = <0x1480000 0x2000000>; + }; + + }; + + mdio0: mdio { + compatible = "virtual,mdio-gpio"; + #address-cells = <1>; + #size-cells = <0>; + gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>; + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; + + phy0: ethernet-phy@0 { + device_type = "ethernet-phy"; + reg = <0>; + qca,ar8327-initvals = < + 0x00004 0x7600000 /* PAD0_MODE */ + 0x00008 0x1000000 /* PAD5_MODE */ + 0x0000c 0x80 /* PAD6_MODE */ + 0x000e4 0xaa545 /* MAC_POWER_SEL */ + 0x000e0 0xc74164de /* SGMII_CTRL */ + 0x0007c 0x4e /* PORT0_STATUS */ + 0x00094 0x4e /* PORT6_STATUS */ + >; + }; + + phy4: ethernet-phy@4 { + device_type = "ethernet-phy"; + reg = <4>; + }; + }; + + gmac1: ethernet@37200000 { + status = "ok"; + phy-mode = "rgmii"; + qcom,id = <1>; + + pinctrl-0 = <&rgmii2_pins>; + pinctrl-names = "default"; + + mtd-mac-address = <&art 6>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + gmac2: ethernet@37400000 { + status = "ok"; + phy-mode = "sgmii"; + qcom,id = <2>; + + mtd-mac-address = <&art 0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + wifi { + label = "wifi"; + gpios = <&qcom_pinmux 6 1>; + linux,code = ; + }; + + reset { + label = "reset"; + gpios = <&qcom_pinmux 54 1>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&qcom_pinmux 65 1>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + usb1 { + label = "r7800:amber:usb1"; + gpios = <&qcom_pinmux 7 0>; + }; + + usb3 { + label = "r7800:amber:usb3"; + gpios = <&qcom_pinmux 8 0>; + }; + + status { + label = "r7800:amber:status"; + gpios = <&qcom_pinmux 9 0>; + }; + + internet { + label = "r7800:white:internet"; + gpios = <&qcom_pinmux 22 0>; + }; + + wan { + label = "r7800:white:wan"; + gpios = <&qcom_pinmux 23 0>; + }; + + wps { + label = "r7800:white:wps"; + gpios = <&qcom_pinmux 24 0>; + }; + + esata { + label = "r7800:white:esata"; + gpios = <&qcom_pinmux 26 0>; + }; + + power { + label = "r7800:white:power"; + gpios = <&qcom_pinmux 53 0>; + default-state = "on"; + }; + + rfkill { + label = "r7800:white:rfkill"; + gpios = <&qcom_pinmux 64 0>; + }; + + wifi { + label = "r7800:white:wifi"; + gpios = <&qcom_pinmux 67 0>; + }; + }; +}; + +&adm_dma { + status = "ok"; +}; diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-v1.0.dtsi b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-v1.0.dtsi new file mode 100644 index 0000000000..22b5338cc0 --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-v1.0.dtsi @@ -0,0 +1 @@ +#include "qcom-ipq8065.dtsi" diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065.dtsi b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065.dtsi new file mode 100644 index 0000000000..4571ef4934 --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065.dtsi @@ -0,0 +1,1185 @@ +/dts-v1/; + +#include "skeleton.dtsi" +#include +#include +#include +#include +#include +#include + +/ { + model = "Qualcomm IPQ8065"; + compatible = "qcom,ipq8065"; + interrupt-parent = <&intc>; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + compatible = "qcom,krait"; + enable-method = "qcom,kpss-acc-v1"; + device_type = "cpu"; + reg = <0>; + next-level-cache = <&L2>; + qcom,acc = <&acc0>; + qcom,saw = <&saw0>; + clocks = <&kraitcc 0>; + clock-names = "cpu"; + clock-latency = <100000>; + core-supply = <&smb208_s2a>; + voltage-tolerance = <5>; + cooling-min-state = <0>; + cooling-max-state = <10>; + #cooling-cells = <2>; + + operating-points-0-0 = < + /* kHz uV */ + 1725000 1262500 + 1400000 1175000 + 1000000 1100000 + 800000 1050000 + 600000 1000000 + 384000 975000 + >; + operating-points-0-1 = < + /* kHz uV */ + 1725000 1262500 + 1400000 1175000 + 1000000 1100000 + 800000 1050000 + 600000 1000000 + 384000 950000 + >; + operating-points-0-2 = < + /* kHz uV */ + 1725000 1200000 + 1400000 1125000 + 1000000 1050000 + 800000 1000000 + 600000 950000 + 384000 925000 + >; + operating-points-0-3 = < + /* kHz uV */ + 1725000 1175000 + 1400000 1100000 + 1000000 1025000 + 800000 975000 + 600000 925000 + 384000 900000 + >; + operating-points-0-4 = < + /* kHz uV */ + 1725000 1150000 + 1400000 1075000 + 1000000 1000000 + 800000 950000 + 600000 900000 + 384000 875000 + >; + operating-points-0-5 = < + /* kHz uV */ + 1725000 1100000 + 1400000 1025000 + 1000000 950000 + 800000 900000 + 600000 850000 + 384000 825000 + >; + operating-points-0-6 = < + /* kHz uV */ + 1725000 1050000 + 1400000 975000 + 1000000 900000 + 800000 850000 + 600000 800000 + 384000 775000 + >; + }; + + cpu@1 { + compatible = "qcom,krait"; + enable-method = "qcom,kpss-acc-v1"; + device_type = "cpu"; + reg = <1>; + next-level-cache = <&L2>; + qcom,acc = <&acc1>; + qcom,saw = <&saw1>; + clocks = <&kraitcc 1>; + clock-names = "cpu"; + clock-latency = <100000>; + core-supply = <&smb208_s2b>; + + operating-points-0-0 = < + /* kHz uV */ + 1725000 1262500 + 1400000 1175000 + 1000000 1100000 + 800000 1050000 + 600000 1000000 + 384000 975000 + >; + operating-points-0-1 = < + /* kHz uV */ + 1725000 1262500 + 1400000 1175000 + 1000000 1100000 + 800000 1050000 + 600000 1000000 + 384000 950000 + >; + operating-points-0-2 = < + /* kHz uV */ + 1725000 1200000 + 1400000 1125000 + 1000000 1050000 + 800000 1000000 + 600000 950000 + 384000 925000 + >; + operating-points-0-3 = < + /* kHz uV */ + 1725000 1175000 + 1400000 1100000 + 1000000 1025000 + 800000 975000 + 600000 925000 + 384000 900000 + >; + operating-points-0-4 = < + /* kHz uV */ + 1725000 1150000 + 1400000 1075000 + 1000000 1000000 + 800000 950000 + 600000 900000 + 384000 875000 + >; + operating-points-0-5 = < + /* kHz uV */ + 1725000 1100000 + 1400000 1025000 + 1000000 950000 + 800000 900000 + 600000 850000 + 384000 825000 + >; + operating-points-0-6 = < + /* kHz uV */ + 1725000 1050000 + 1400000 975000 + 1000000 900000 + 800000 850000 + 600000 800000 + 384000 775000 + >; + cooling-min-state = <0>; + cooling-max-state = <10>; + #cooling-cells = <2>; + }; + + L2: l2-cache { + compatible = "cache"; + cache-level = <2>; + clocks = <&kraitcc 4>; + clock-names = "cache"; + cache-points-kHz = < + /* kHz uV CPU kHz */ + 1200000 1150000 1200000 + 1000000 1100000 600000 + 384000 1100000 384000 + >; + vdd_dig-supply = <&smb208_s1a>; + }; + }; + + cpu-pmu { + compatible = "qcom,krait-pmu"; + interrupts = <1 10 0x304>; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + nss@40000000 { + reg = <0x40000000 0x1000000>; + no-map; + }; + + smem: smem@41000000 { + reg = <0x41000000 0x200000>; + no-map; + }; + }; + + clocks { + sleep_clk: sleep_clk { + compatible = "fixed-clock"; + clock-frequency = <32768>; + #clock-cells = <0>; + }; + }; + + kraitcc: clock-controller { + compatible = "qcom,krait-cc-v1"; + #clock-cells = <1>; + }; + + qcom,pvs { + qcom,pvs-format-a; + qcom,speed0-pvs0-bin-v0 = + < 1725000000 1262500 >, + < 1400000000 1175000 >, + < 1000000000 1100000 >, + < 800000000 1050000 >, + < 600000000 1000000 >, + < 384000000 975000 >; + qcom,speed0-pvs1-bin-v0 = + < 1725000000 1262500 >, + < 1400000000 1175000 >, + < 1000000000 1100000 >, + < 800000000 1050000 >, + < 600000000 1000000 >, + < 384000000 950000 >; + qcom,speed0-pvs2-bin-v0 = + < 1725000000 1200000 >, + < 1400000000 1125000 >, + < 1000000000 1050000 >, + < 800000000 1000000 >, + < 600000000 950000 >, + < 384000000 925000 >; + qcom,speed0-pvs3-bin-v0 = + < 1725000000 1175000 >, + < 1400000000 1100000 >, + < 1000000000 1025000 >, + < 800000000 975000 >, + < 600000000 925000 >, + < 384000000 900000 >; + qcom,speed0-pvs4-bin-v0 = + < 1725000000 1150000 >, + < 1400000000 1075000 >, + < 1000000000 1000000 >, + < 800000000 950000 >, + < 600000000 900000 >, + < 384000000 875000 >; + qcom,speed0-pvs5-bin-v0 = + < 1725000000 1100000 >, + < 1400000000 1025000 >, + < 1000000000 950000 >, + < 800000000 900000 >, + < 600000000 850000 >, + < 384000000 825000 >; + qcom,speed0-pvs6-bin-v0 = + < 1725000000 1050000 >, + < 1400000000 975000 >, + < 1000000000 900000 >, + < 800000000 850000 >, + < 600000000 800000 >, + < 384000000 775000 >; + }; + + soc: soc { + #address-cells = <1>; + #size-cells = <1>; + ranges; + compatible = "simple-bus"; + + imem: memory@700000 { + compatible = "qcom,imem-ipq8064", "syscon"; + reg = <0x00700000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x00700000 0x1000>; + }; + + rpm@108000 { + compatible = "qcom,rpm-ipq8064"; + reg = <0x108000 0x1000>; + qcom,ipc = <&l2cc 0x8 2>; + + interrupts = <0 19 0>, + <0 21 0>, + <0 22 0>; + interrupt-names = "ack", + "err", + "wakeup"; + + #address-cells = <1>; + #size-cells = <0>; + + smb208_s1a: smb208-s1a { + compatible = "qcom,rpm-smb208"; + reg = ; + + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1150000>; + + qcom,switch-mode-frequency = <1200000>; + + }; + + smb208_s1b: smb208-s1b { + compatible = "qcom,rpm-smb208"; + reg = ; + + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1150000>; + + qcom,switch-mode-frequency = <1200000>; + }; + + smb208_s2a: smb208-s2a { + compatible = "qcom,rpm-smb208"; + reg = ; + + regulator-min-microvolt = < 800000>; + regulator-max-microvolt = <1275000>; + + qcom,switch-mode-frequency = <1400000>; + }; + + smb208_s2b: smb208-s2b { + compatible = "qcom,rpm-smb208"; + reg = ; + + regulator-min-microvolt = < 800000>; + regulator-max-microvolt = <1275000>; + + qcom,switch-mode-frequency = <1400000>; + }; + + cxo_clk: cxo-clk { + #clock-cells = <0>; + compatible = "qcom,rpm-clk"; + reg = ; + qcom,rpm-clk-name = "cxo"; + qcom,rpm-clk-freq = <25000000>; + qcom,rpm-clk-active-only; + }; + + pxo_clk: pxo-clk { + #clock-cells = <0>; + compatible = "qcom,rpm-clk"; + reg = ; + qcom,rpm-clk-name = "pxo"; + qcom,rpm-clk-freq = <25000000>; + qcom,rpm-clk-active-only; + }; + + ebi1_clk: ebi1-clk { + #clock-cells = <0>; + compatible = "qcom,rpm-clk"; + reg = ; + qcom,rpm-clk-name = "ebi1"; + qcom,rpm-clk-freq = <533000000>; + qcom,rpm-clk-active-only; + }; + + apps_fabric_clk: apps-fabric-clk { + #clock-cells = <0>; + compatible = "qcom,rpm-clk"; + reg = ; + qcom,rpm-clk-name = "apps-fabric"; + qcom,rpm-clk-freq = <533000000>; + qcom,rpm-clk-active-only; + }; + + nss_fabric0_clk: nss-fabric0-clk { + #clock-cells = <0>; + compatible = "qcom,rpm-clk"; + reg = ; + qcom,rpm-clk-name = "nss-fabric0"; + qcom,rpm-clk-freq = <533000000>; + qcom,rpm-clk-active-only; + }; + + nss_fabric1_clk: nss-fabric1-clk { + #clock-cells = <0>; + compatible = "qcom,rpm-clk"; + reg = ; + qcom,rpm-clk-name = "nss-fabric1"; + qcom,rpm-clk-freq = <266000000>; + qcom,rpm-clk-active-only; + }; + }; + + rng@1a500000 { + compatible = "qcom,prng"; + reg = <0x1a500000 0x200>; + clocks = <&gcc PRNG_CLK>; + clock-names = "core"; + }; + + qcom,msm-imem@2A03F000 { + compatible = "qcom,msm-imem"; + reg = <0x2A03F000 0x1000>; /* Address and size of IMEM */ + ranges = <0x0 0x2A03F000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + + download_mode@0 { + compatible = "qcom,msm-imem-download_mode"; + reg = <0x0 8>; + }; + + restart_reason@65c { + compatible = "qcom,msm-imem-restart_reason"; + reg = <0x65c 4>; + }; + + l2_dump_offset@14 { + compatible = "qcom,msm-imem-l2_dump_offset"; + reg = <0x14 8>; + }; + }; + + qcom_pinmux: pinmux@800000 { + compatible = "qcom,ipq8064-pinctrl"; + reg = <0x800000 0x4000>; + + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <0 32 0x4>; + + pcie0_pins: pcie0_pinmux { + mux { + pins = "gpio3"; + function = "pcie1_rst"; + drive-strength = <12>; + bias-disable; + }; + }; + + pcie1_pins: pcie1_pinmux { + mux { + pins = "gpio48"; + function = "pcie2_rst"; + drive-strength = <12>; + bias-disable; + }; + }; + + pcie2_pins: pcie2_pinmux { + mux { + pins = "gpio63"; + function = "pcie3_rst"; + drive-strength = <12>; + bias-disable; + }; + }; + }; + + intc: interrupt-controller@2000000 { + compatible = "qcom,msm-qgic2"; + interrupt-controller; + #interrupt-cells = <3>; + reg = <0x02000000 0x1000>, + <0x02002000 0x1000>; + }; + + timer@200a000 { + compatible = "qcom,kpss-timer", "qcom,msm-timer"; + interrupts = <1 1 0x301>, + <1 2 0x301>, + <1 3 0x301>, + <1 4 0x301>, + <1 5 0x301>; + reg = <0x0200a000 0x100>; + clock-frequency = <25000000>, + <32768>; + clocks = <&sleep_clk>; + clock-names = "sleep"; + cpu-offset = <0x80000>; + }; + + acc0: clock-controller@2088000 { + compatible = "qcom,kpss-acc-v1"; + reg = <0x02088000 0x1000>, <0x02008000 0x1000>; + clock-output-names = "acpu0_aux"; + }; + + acc1: clock-controller@2098000 { + compatible = "qcom,kpss-acc-v1"; + reg = <0x02098000 0x1000>, <0x02008000 0x1000>; + clock-output-names = "acpu1_aux"; + }; + + l2cc: clock-controller@2011000 { + compatible = "qcom,kpss-gcc", "syscon"; + reg = <0x2011000 0x1000>; + clock-output-names = "acpu_l2_aux"; + }; + + saw0: regulator@2089000 { + compatible = "qcom,saw2"; + reg = <0x02089000 0x1000>, <0x02009000 0x1000>; + regulator; + }; + + saw1: regulator@2099000 { + compatible = "qcom,saw2"; + reg = <0x02099000 0x1000>, <0x02009000 0x1000>; + regulator; + }; + + gsbi2: gsbi@12480000 { + compatible = "qcom,gsbi-v1.0.0"; + cell-index = <2>; + reg = <0x12480000 0x100>; + clocks = <&gcc GSBI2_H_CLK>; + clock-names = "iface"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + status = "disabled"; + + syscon-tcsr = <&tcsr>; + + uart2: serial@12490000 { + compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; + reg = <0x12490000 0x1000>, + <0x12480000 0x1000>; + interrupts = <0 195 0x0>; + clocks = <&gcc GSBI2_UART_CLK>, <&gcc GSBI2_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + }; + + i2c@124a0000 { + compatible = "qcom,i2c-qup-v1.1.1"; + reg = <0x124a0000 0x1000>; + interrupts = <0 196 0>; + + clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + + #address-cells = <1>; + #size-cells = <0>; + }; + + }; + + gsbi4: gsbi@16300000 { + compatible = "qcom,gsbi-v1.0.0"; + cell-index = <4>; + reg = <0x16300000 0x100>; + clocks = <&gcc GSBI4_H_CLK>; + clock-names = "iface"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + status = "disabled"; + + syscon-tcsr = <&tcsr>; + + uart4: serial@16340000 { + compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; + reg = <0x16340000 0x1000>, + <0x16300000 0x1000>; + interrupts = <0 152 0x0>; + clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + }; + + i2c@16380000 { + compatible = "qcom,i2c-qup-v1.1.1"; + reg = <0x16380000 0x1000>; + interrupts = <0 153 0>; + + clocks = <&gcc GSBI4_QUP_CLK>, <&gcc GSBI4_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + + #address-cells = <1>; + #size-cells = <0>; + }; + }; + + gsbi5: gsbi@1a200000 { + compatible = "qcom,gsbi-v1.0.0"; + cell-index = <5>; + reg = <0x1a200000 0x100>; + clocks = <&gcc GSBI5_H_CLK>; + clock-names = "iface"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + status = "disabled"; + + syscon-tcsr = <&tcsr>; + + uart5: serial@1a240000 { + compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; + reg = <0x1a240000 0x1000>, + <0x1a200000 0x1000>; + interrupts = <0 154 0x0>; + clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + }; + + i2c@1a280000 { + compatible = "qcom,i2c-qup-v1.1.1"; + reg = <0x1a280000 0x1000>; + interrupts = <0 155 0>; + + clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + + #address-cells = <1>; + #size-cells = <0>; + }; + + spi@1a280000 { + compatible = "qcom,spi-qup-v1.1.1"; + reg = <0x1a280000 0x1000>; + interrupts = <0 155 0>; + + clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + + #address-cells = <1>; + #size-cells = <0>; + }; + }; + + sata_phy: sata-phy@1b400000 { + compatible = "qcom,ipq806x-sata-phy"; + reg = <0x1b400000 0x200>; + + clocks = <&gcc SATA_PHY_CFG_CLK>; + clock-names = "cfg"; + + #phy-cells = <0>; + status = "disabled"; + }; + + sata@29000000 { + compatible = "qcom,ipq806x-ahci", "generic-ahci"; + reg = <0x29000000 0x180>; + + interrupts = <0 209 0x0>; + + clocks = <&gcc SFAB_SATA_S_H_CLK>, + <&gcc SATA_H_CLK>, + <&gcc SATA_A_CLK>, + <&gcc SATA_RXOOB_CLK>, + <&gcc SATA_PMALIVE_CLK>; + clock-names = "slave_face", "iface", "core", + "rxoob", "pmalive"; + + assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>; + assigned-clock-rates = <100000000>, <100000000>; + + phys = <&sata_phy>; + phy-names = "sata-phy"; + status = "disabled"; + }; + + qcom,ssbi@500000 { + compatible = "qcom,ssbi"; + reg = <0x00500000 0x1000>; + qcom,controller-type = "pmic-arbiter"; + }; + + gcc: clock-controller@900000 { + compatible = "qcom,gcc-ipq8064"; + reg = <0x00900000 0x4000>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + tcsr: syscon@1a400000 { + compatible = "qcom,tcsr-ipq8064", "syscon"; + reg = <0x1a400000 0x100>; + }; + + tsens: tsens-ipq806x { + compatible = "qcom,ipq806x-tsens"; + reg = <0x900000 0x3678>, <0x700000 0x420>; + reg-names = "tsens_physical", "tsens_eeprom_physical"; + interrupts = <0 178 0>; + qcom,sensors = <11>; + qcom,tsens_factor = <1000>; + qcom,slope = <1176 1176 1154 1176 1111 1132 1132 1199 1132 1199 1132>; + }; + + qcom,msm-thermal { + compatible = "qcom,msm-thermal"; + qcom,sensor-id = <0>; + qcom,poll-ms = <250>; + qcom,limit-temp = <105>; + qcom,temp-hysteresis = <10>; + qcom,freq-step = <2>; + qcom,core-limit-temp = <115>; + qcom,core-temp-hysteresis = <10>; + qcom,core-control-mask = <0xe>; + }; + + sfpb_mutex_block: syscon@1200600 { + compatible = "syscon"; + reg = <0x01200600 0x100>; + }; + + hs_phy_1: phy@100f8800 { + compatible = "qcom,dwc3-hs-usb-phy"; + reg = <0x100f8800 0x30>; + clocks = <&gcc USB30_1_UTMI_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + + status = "disabled"; + }; + + ss_phy_1: phy@100f8830 { + compatible = "qcom,dwc3-ss-usb-phy"; + reg = <0x100f8830 0x30>; + clocks = <&gcc USB30_1_MASTER_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + + status = "disabled"; + }; + + hs_phy_0: phy@110f8800 { + compatible = "qcom,dwc3-hs-usb-phy"; + reg = <0x110f8800 0x30>; + clocks = <&gcc USB30_0_UTMI_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + + status = "disabled"; + }; + + ss_phy_0: phy@110f8830 { + compatible = "qcom,dwc3-ss-usb-phy"; + reg = <0x110f8830 0x30>; + clocks = <&gcc USB30_0_MASTER_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + + status = "disabled"; + }; + + usb3_0: usb30@0 { + compatible = "qcom,dwc3"; + #address-cells = <1>; + #size-cells = <1>; + clocks = <&gcc USB30_0_MASTER_CLK>; + clock-names = "core"; + + ranges; + + status = "disabled"; + resets = <&gcc USB30_0_MASTER_RESET>; + reset-names = "usb30_mstr_rst"; + + dwc3@11000000 { + compatible = "snps,dwc3"; + reg = <0x11000000 0xcd00>; + interrupts = <0 110 0x4>; + phys = <&hs_phy_0>, <&ss_phy_0>; + phy-names = "usb2-phy", "usb3-phy"; + tx-fifo-resize; + dr_mode = "host"; + }; + }; + + usb3_1: usb30@1 { + compatible = "qcom,dwc3"; + #address-cells = <1>; + #size-cells = <1>; + clocks = <&gcc USB30_1_MASTER_CLK>; + clock-names = "core"; + + ranges; + + status = "disabled"; + + dwc3@10000000 { + compatible = "snps,dwc3"; + reg = <0x10000000 0xcd00>; + interrupts = <0 205 0x4>; + phys = <&hs_phy_1>, <&ss_phy_1>; + phy-names = "usb2-phy", "usb3-phy"; + tx-fifo-resize; + dr_mode = "host"; + }; + }; + + pcie0: pci@1b500000 { + compatible = "qcom,pcie-v0"; + reg = <0x1b500000 0x1000 + 0x1b502000 0x80 + 0x1b600000 0x100 + 0x0ff00000 0x100000>; + reg-names = "dbi", "elbi", "parf", "config"; + device_type = "pci"; + linux,pci-domain = <0>; + bus-range = <0x00 0xff>; + num-lanes = <1>; + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x81000000 0 0x0fe00000 0x0fe00000 0 0x00100000 /* downstream I/O */ + 0x82000000 0 0x08000000 0x08000000 0 0x07e00000>; /* non-prefetchable memory */ + + interrupts = ; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc 0 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ + <0 0 0 2 &intc 0 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ + <0 0 0 3 &intc 0 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ + <0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ + + clocks = <&gcc PCIE_A_CLK>, + <&gcc PCIE_H_CLK>, + <&gcc PCIE_PHY_CLK>, + <&gcc PCIE_AUX_CLK>, + <&gcc PCIE_ALT_REF_CLK>; + clock-names = "core", "iface", "phy", "aux", "ref"; + + assigned-clocks = <&gcc PCIE_ALT_REF_CLK>; + assigned-clock-rates = <100000000>; + + resets = <&gcc PCIE_ACLK_RESET>, + <&gcc PCIE_HCLK_RESET>, + <&gcc PCIE_POR_RESET>, + <&gcc PCIE_PCI_RESET>, + <&gcc PCIE_PHY_RESET>, + <&gcc PCIE_EXT_RESET>; + reset-names = "axi", "ahb", "por", "pci", "phy", "ext"; + + pinctrl-0 = <&pcie0_pins>; + pinctrl-names = "default"; + + perst-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>; + + status = "disabled"; + }; + + pcie1: pci@1b700000 { + compatible = "qcom,pcie-v0"; + reg = <0x1b700000 0x1000 + 0x1b702000 0x80 + 0x1b800000 0x100 + 0x31f00000 0x100000>; + reg-names = "dbi", "elbi", "parf", "config"; + device_type = "pci"; + linux,pci-domain = <1>; + bus-range = <0x00 0xff>; + num-lanes = <1>; + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x81000000 0 0x31e00000 0x31e00000 0 0x00100000 /* downstream I/O */ + 0x82000000 0 0x2e000000 0x2e000000 0 0x03e00000>; /* non-prefetchable memory */ + + interrupts = ; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc 0 58 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ + <0 0 0 2 &intc 0 59 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ + <0 0 0 3 &intc 0 60 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ + <0 0 0 4 &intc 0 61 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ + + clocks = <&gcc PCIE_1_A_CLK>, + <&gcc PCIE_1_H_CLK>, + <&gcc PCIE_1_PHY_CLK>, + <&gcc PCIE_1_AUX_CLK>, + <&gcc PCIE_1_ALT_REF_CLK>; + clock-names = "core", "iface", "phy", "aux", "ref"; + + assigned-clocks = <&gcc PCIE_1_ALT_REF_CLK>; + assigned-clock-rates = <100000000>; + + resets = <&gcc PCIE_1_ACLK_RESET>, + <&gcc PCIE_1_HCLK_RESET>, + <&gcc PCIE_1_POR_RESET>, + <&gcc PCIE_1_PCI_RESET>, + <&gcc PCIE_1_PHY_RESET>, + <&gcc PCIE_1_EXT_RESET>; + reset-names = "axi", "ahb", "por", "pci", "phy", "ext"; + + pinctrl-0 = <&pcie1_pins>; + pinctrl-names = "default"; + + perst-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>; + + status = "disabled"; + }; + + pcie2: pci@1b900000 { + compatible = "qcom,pcie-v0"; + reg = <0x1b900000 0x1000 + 0x1b902000 0x80 + 0x1ba00000 0x100 + 0x35f00000 0x100000>; + reg-names = "dbi", "elbi", "parf", "config"; + device_type = "pci"; + linux,pci-domain = <2>; + bus-range = <0x00 0xff>; + num-lanes = <1>; + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x81000000 0 0x35e00000 0x35e00000 0 0x00100000 /* downstream I/O */ + 0x82000000 0 0x32000000 0x32000000 0 0x03e00000>; /* non-prefetchable memory */ + + interrupts = ; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc 0 72 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ + <0 0 0 2 &intc 0 73 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ + <0 0 0 3 &intc 0 74 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ + <0 0 0 4 &intc 0 75 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ + + clocks = <&gcc PCIE_2_A_CLK>, + <&gcc PCIE_2_H_CLK>, + <&gcc PCIE_2_PHY_CLK>, + <&gcc PCIE_2_AUX_CLK>, + <&gcc PCIE_2_ALT_REF_CLK>; + clock-names = "core", "iface", "phy", "aux", "ref"; + + assigned-clocks = <&gcc PCIE_2_ALT_REF_CLK>; + assigned-clock-rates = <100000000>; + + resets = <&gcc PCIE_2_ACLK_RESET>, + <&gcc PCIE_2_HCLK_RESET>, + <&gcc PCIE_2_POR_RESET>, + <&gcc PCIE_2_PCI_RESET>, + <&gcc PCIE_2_PHY_RESET>, + <&gcc PCIE_2_EXT_RESET>; + reset-names = "axi", "ahb", "por", "pci", "phy", "ext"; + + pinctrl-0 = <&pcie2_pins>; + pinctrl-names = "default"; + + perst-gpio = <&qcom_pinmux 63 GPIO_ACTIVE_LOW>; + + status = "disabled"; + }; + + adm_dma: dma@18300000 { + compatible = "qcom,adm"; + reg = <0x18300000 0x100000>; + interrupts = <0 170 0>; + #dma-cells = <1>; + + clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>; + clock-names = "core", "iface"; + + resets = <&gcc ADM0_RESET>, + <&gcc ADM0_PBUS_RESET>, + <&gcc ADM0_C0_RESET>, + <&gcc ADM0_C1_RESET>, + <&gcc ADM0_C2_RESET>; + reset-names = "clk", "pbus", "c0", "c1", "c2"; + qcom,ee = <0>; + + status = "disabled"; + }; + + nand@1ac00000 { + compatible = "qcom,ebi2-nandc"; + reg = <0x1ac00000 0x800>; + + clocks = <&gcc EBI2_CLK>, + <&gcc EBI2_AON_CLK>; + clock-names = "core", "aon"; + + dmas = <&adm_dma 3>; + dma-names = "rxtx"; + qcom,cmd-crci = <15>; + qcom,data-crci = <3>; + + status = "disabled"; + }; + + nss_common: syscon@03000000 { + compatible = "syscon"; + reg = <0x03000000 0x0000FFFF>; + }; + + qsgmii_csr: syscon@1bb00000 { + compatible = "syscon"; + reg = <0x1bb00000 0x000001FF>; + }; + + gmac0: ethernet@37000000 { + device_type = "network"; + compatible = "qcom,ipq806x-gmac"; + reg = <0x37000000 0x200000>; + interrupts = ; + interrupt-names = "macirq"; + + qcom,nss-common = <&nss_common>; + qcom,qsgmii-csr = <&qsgmii_csr>; + + clocks = <&gcc GMAC_CORE1_CLK>; + clock-names = "stmmaceth"; + + resets = <&gcc GMAC_CORE1_RESET>; + reset-names = "stmmaceth"; + + status = "disabled"; + }; + + gmac1: ethernet@37200000 { + device_type = "network"; + compatible = "qcom,ipq806x-gmac"; + reg = <0x37200000 0x200000>; + interrupts = ; + interrupt-names = "macirq"; + + qcom,nss-common = <&nss_common>; + qcom,qsgmii-csr = <&qsgmii_csr>; + + clocks = <&gcc GMAC_CORE2_CLK>; + clock-names = "stmmaceth"; + + resets = <&gcc GMAC_CORE2_RESET>; + reset-names = "stmmaceth"; + + status = "disabled"; + }; + + gmac2: ethernet@37400000 { + device_type = "network"; + compatible = "qcom,ipq806x-gmac"; + reg = <0x37400000 0x200000>; + interrupts = ; + interrupt-names = "macirq"; + + qcom,nss-common = <&nss_common>; + qcom,qsgmii-csr = <&qsgmii_csr>; + + clocks = <&gcc GMAC_CORE3_CLK>; + clock-names = "stmmaceth"; + + resets = <&gcc GMAC_CORE3_RESET>; + reset-names = "stmmaceth"; + + status = "disabled"; + }; + + gmac3: ethernet@37600000 { + device_type = "network"; + compatible = "qcom,ipq806x-gmac"; + reg = <0x37600000 0x200000>; + interrupts = ; + interrupt-names = "macirq"; + + qcom,nss-common = <&nss_common>; + qcom,qsgmii-csr = <&qsgmii_csr>; + + clocks = <&gcc GMAC_CORE4_CLK>; + clock-names = "stmmaceth"; + + resets = <&gcc GMAC_CORE4_RESET>; + reset-names = "stmmaceth"; + + status = "disabled"; + }; + /* Temporary fixed regulator */ + vsdcc_fixed: vsdcc-regulator { + compatible = "regulator-fixed"; + regulator-name = "SDCC Power"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + sdcc1bam:dma@12402000 { + compatible = "qcom,bam-v1.3.0"; + reg = <0x12402000 0x8000>; + interrupts = <0 98 0>; + clocks = <&gcc SDC1_H_CLK>; + clock-names = "bam_clk"; + #dma-cells = <1>; + qcom,ee = <0>; + }; + + sdcc3bam:dma@12182000 { + compatible = "qcom,bam-v1.3.0"; + reg = <0x12182000 0x8000>; + interrupts = <0 96 0>; + clocks = <&gcc SDC3_H_CLK>; + clock-names = "bam_clk"; + #dma-cells = <1>; + qcom,ee = <0>; + }; + + amba { + compatible = "arm,amba-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + sdcc1: sdcc@12400000 { + status = "disabled"; + compatible = "arm,pl18x", "arm,primecell"; + arm,primecell-periphid = <0x00051180>; + reg = <0x12400000 0x2000>; + interrupts = ; + interrupt-names = "cmd_irq"; + clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>; + clock-names = "mclk", "apb_pclk"; + bus-width = <8>; + max-frequency = <48000000>; + non-removable; + cap-sd-highspeed; + cap-mmc-highspeed; + vmmc-supply = <&vsdcc_fixed>; + #dmas = <&sdcc1bam 2>, <&sdcc1bam 1>; + #dma-names = "tx", "rx"; + }; + + sdcc3: sdcc@12180000 { + compatible = "arm,pl18x", "arm,primecell"; + arm,primecell-periphid = <0x00051180>; + status = "disabled"; + reg = <0x12180000 0x2000>; + interrupts = ; + interrupt-names = "cmd_irq"; + clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>; + clock-names = "mclk", "apb_pclk"; + bus-width = <8>; + cap-sd-highspeed; + cap-mmc-highspeed; + max-frequency = <192000000>; + #mmc-ddr-1_8v; + sd-uhs-sdr50; + vmmc-supply = <&vsdcc_fixed>; + #dmas = <&sdcc3bam 2>, <&sdcc3bam 1>; + #dma-names = "tx", "rx"; + }; + }; + + }; + + sfpb_mutex: sfpb-mutex { + compatible = "qcom,sfpb-mutex"; + syscon = <&sfpb_mutex_block 4 4>; + + #hwlock-cells = <1>; + }; + + smem { + compatible = "qcom,smem"; + memory-region = <&smem>; + hwlocks = <&sfpb_mutex 3>; + }; +}; diff --git a/target/linux/ipq806x/image/Makefile b/target/linux/ipq806x/image/Makefile index e039df7822..43de23e1a7 100644 --- a/target/linux/ipq806x/image/Makefile +++ b/target/linux/ipq806x/image/Makefile @@ -185,6 +185,19 @@ define Device/R7500 DEVICE_PACKAGES := ath10k-firmware-qca99x0 endef -TARGET_DEVICES += AP148 AP148-legacy C2600 D7800 DB149 EA8500 R7500 +define Device/R7800 + $(call Device/DniImage) + DEVICE_DTS := qcom-ipq8064-r7800 + KERNEL_SIZE := 2097152 + NETGEAR_BOARD_ID := R7800 + NETGEAR_HW_ID := 29764958+0+128+512+4x4+4x4+cascade + BLOCKSIZE := 128KiB + PAGESIZE := 2048 + BOARD_NAME := r7800 + DEVICE_TITLE := Netgear Nighthawk X4S R7800 + DEVICE_PACKAGES := ath10k-firmware-qca9984 +endef + +TARGET_DEVICES += AP148 AP148-legacy C2600 D7800 DB149 EA8500 R7500 R7800 $(eval $(call BuildImage)) diff --git a/target/linux/ipq806x/patches-4.4/800-devicetree.patch b/target/linux/ipq806x/patches-4.4/800-devicetree.patch index fc59837f66..0081a28885 100644 --- a/target/linux/ipq806x/patches-4.4/800-devicetree.patch +++ b/target/linux/ipq806x/patches-4.4/800-devicetree.patch @@ -12,7 +12,7 @@ Signed-off-by: Jonas Gorski --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -506,7 +506,11 @@ +@@ -506,7 +506,12 @@ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ qcom-ipq8064-ap148.dtb \ @@ -21,6 +21,7 @@ Signed-off-by: Jonas Gorski qcom-ipq8064-db149.dtb \ + qcom-ipq8064-ea8500.dtb \ + qcom-ipq8064-r7500.dtb \ ++ qcom-ipq8064-r7800.dtb \ qcom-msm8660-surf.dtb \ qcom-msm8960-cdp.dtb \ qcom-msm8974-sony-xperia-honami.dtb