From: Sven Eckelmann Date: Mon, 23 Nov 2020 12:41:34 +0000 (+0100) Subject: ath79: Add support for OpenMesh OM2P v1 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=8143709c90c3aa0a84e14cf4a9dfbcb365b0d966;p=openwrt%2Fstaging%2Fnbd.git ath79: Add support for OpenMesh OM2P v1 Device specifications: ====================== * Qualcomm/Atheros AR7240 rev 2 * 350/350/175 MHz (CPU/DDR/AHB) * 32 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2x 10/100 Mbps Ethernet * 1T1R 2.4 GHz Wi-Fi * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x fast ethernet - eth0 + 18-24V passive POE (mode B) + used as WAN interface - eth1 + builtin switch port 4 + used as LAN interface * 12-24V 1A DC * external antenna The device itself requires the mtdparts from the uboot arguments to properly boot the flashed image and to support dual-boot (primary + recovery image). Unfortunately, the name of the mtd device in mtdparts is still using the legacy name "ar7240-nor0" which must be supplied using the Linux-specfic DT parameter linux,mtd-name to overwrite the generic name "spi0.0". Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 .bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp .bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/.bin Signed-off-by: Sven Eckelmann --- diff --git a/package/boot/uboot-envtools/files/ath79 b/package/boot/uboot-envtools/files/ath79 index b01a713705..7aa992e458 100644 --- a/package/boot/uboot-envtools/files/ath79 +++ b/package/boot/uboot-envtools/files/ath79 @@ -103,6 +103,7 @@ netgear,wndr4300tn|\ netgear,wndr4300sw) ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x40000" "0x20000" ;; +openmesh,om2p-v1|\ openmesh,om2p-v2|\ openmesh,om2p-v4|\ openmesh,om2p-hs-v1|\ diff --git a/target/linux/ath79/dts/ar7240_openmesh_om2p-v1.dts b/target/linux/ath79/dts/ar7240_openmesh_om2p-v1.dts new file mode 100644 index 0000000000..456724a750 --- /dev/null +++ b/target/linux/ath79/dts/ar7240_openmesh_om2p-v1.dts @@ -0,0 +1,170 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "ar7240.dtsi" + +#include +#include + +/ { + compatible = "openmesh,om2p-v1", "qca,ar7240"; + model = "OpenMesh OM2P v1"; + + chosen { + /delete-property/ bootargs; + }; + + aliases { + led-boot = &led_power_blue; + led-failsafe = &led_power_blue; + led-running = &led_power_blue; + led-upgrade = &led_power_blue; + label-mac-device = ð0; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + linux,code = ; + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + }; + }; + + leds { + compatible = "gpio-leds"; + + pinctrl-names = "default"; + pinctrl-0 = <&switch_led_disable_pins>; + + led_power_blue: power_blue { + label = "blue:power"; + gpios = <&gpio 0 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + + wifi_green { + label = "green:wifi"; + gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + wifi_red { + label = "red:wifi"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + }; + + wifi_yellow { + label = "yellow:wifi"; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + }; + + lan_blue { + label = "blue:lan"; + gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + }; + + wan_blue { + label = "blue:wan"; + gpios = <&gpio 17 GPIO_ACTIVE_LOW>; + }; + }; + + watchdog { + compatible = "linux,wdt-gpio"; + gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + hw_algo = "toggle"; + /* hw_margin_ms is actually 300s but driver limits it to 60s */ + hw_margin_ms = <60000>; + always-running; + }; +}; + +&spi { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <40000000>; + linux,mtd-name = "ar7240-nor0"; + + /* partitions are passed via bootloader */ + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x000000 0x040000>; + read-only; + }; + + partition@40000 { + label = "u-boot-env"; + reg = <0x040000 0x040000>; + }; + + partition@80000 { + label = "custom"; + reg = <0x080000 0x140000>; + read-only; + }; + + partition@1c0000 { + label = "inactive"; + reg = <0x1c0000 0x700000>; + }; + + partition@8c0000 { + label = "inactive2"; + reg = <0x8c0000 0x700000>; + }; + + art: partition@fc0000 { + label = "ART"; + reg = <0xfc0000 0x040000>; + read-only; + }; + }; + }; +}; + +ð0 { + nvmem-cells = <&macaddr_art_0>; + nvmem-cell-names = "mac-address"; +}; + +ð1 { + status = "okay"; + + nvmem-cells = <&macaddr_art_6>; + nvmem-cell-names = "mac-address"; +}; + +&pcie { + status = "okay"; + + wifi@0,0 { + compatible = "pci168c,002a"; + reg = <0x0000 0 0 0 0>; + qca,no-eeprom; + #gpio-cells = <2>; + gpio-controller; + }; +}; + +&art { + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_art_0: macaddr@0 { + reg = <0x0 0x6>; + }; + + macaddr_art_6: macaddr@6 { + reg = <0x6 0x6>; + }; +}; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds index 652b54092e..03750856ab 100644 --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds @@ -271,6 +271,10 @@ openmesh,om2p-hs-v4) ucidef_set_led_netdev "wan" "WAN" "blue:wan" "eth0" ucidef_set_led_switch "lan" "LAN" "blue:lan" "switch0" "0x02" ;; +openmesh,om2p-v1) + ucidef_set_led_netdev "wan" "WAN" "blue:wan" "eth0" + ucidef_set_led_switch "lan" "LAN" "blue:lan" "switch0" "0x10" + ;; openmesh,om5p-ac-v1) ucidef_set_led_netdev "lan" "LAN" "blue:lan" "eth0" ucidef_set_led_netdev "wan" "WAN" "blue:wan" "eth1" diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index 88269c03ec..54c4152757 100644 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -188,6 +188,7 @@ ath79_setup_interfaces() compex,wpj531-16m|\ openmesh,a40|\ openmesh,a60|\ + openmesh,om2p-v1|\ openmesh,om2p-v4|\ openmesh,om2p-hs-v4|\ plasmacloud,pa300|\ diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom index 10421c2e28..31b872e618 100644 --- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom +++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom @@ -131,6 +131,9 @@ case "$FIRMWARE" in openmesh,om5p-an) caldata_extract "ART" 0x5000 0x440 ;; + openmesh,om2p-v1) + caldata_extract "ART" 0x1000 0x440 + ;; wd,mynet-n600|\ wd,mynet-n750) caldata_extract "art" 0x5000 0x440 diff --git a/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh b/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh index 13b6ec9d99..67e53c5fde 100644 --- a/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh +++ b/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh @@ -73,6 +73,7 @@ platform_do_upgrade() { openmesh,mr900-v2|\ openmesh,mr1750-v1|\ openmesh,mr1750-v2|\ + openmesh,om2p-v1|\ openmesh,om2p-v2|\ openmesh,om2p-v4|\ openmesh,om2p-hs-v1|\ diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index 64efa28f84..7cde28e85b 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -1836,6 +1836,16 @@ define Device/openmesh_mr1750-v2 endef TARGET_DEVICES += openmesh_mr1750-v2 +define Device/openmesh_om2p-v1 + $(Device/openmesh_common_256k) + SOC := ar7240 + DEVICE_MODEL := OM2P + DEVICE_VARIANT := v1 + OPENMESH_CE_TYPE := OM2P + SUPPORTED_DEVICES += om2p +endef +TARGET_DEVICES += openmesh_om2p-v1 + define Device/openmesh_om2p-v2 $(Device/openmesh_common_256k) SOC := ar9330