From: Paul Maruhn Date: Tue, 22 Mar 2022 20:06:42 +0000 (+0100) Subject: ath79: support for TP-Link EAP225-Outdoor v3 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=7e4de89e631aaf56be5375662b7d5ed0f27e26f6;p=openwrt%2Fstaging%2Fnbd.git ath79: support for TP-Link EAP225-Outdoor v3 This model is almost identical to the EAP225-Outdoor v1. Major difference is the RTL8211FS PHY Chipset. Device specifications: * SoC: QCA9563 @ 775MHz * Memory: 128MiB DDR2 * Flash: 16MiB SPI-NOR * Wireless 2.4GHz (SoC): b/g/n 2x2 * Wireless 5GHz (QCA9886): a/n/ac 2x2 MU-MIMO * Ethernet (RTL8211FS): 1× 1GbE, PoE Flashing instructions: * ssh into target device with recent (>= v1.6.0) firmware * run `cliclientd stopcs` on target device * upload factory image via web interface Debricking: To recover the device, you need access to the serial port. This requires fine soldering to test points, or the use of probe pins. * Open the case and solder wires to the test points: RXD, TXD and TPGND4 * Use a 3.3V UART, 115200 baud, 8n1 * Interrupt bootloader by holding ctrl+B during boot * upload initramfs via built-in tftp client and perform sysupgrade setenv ipaddr 192.168.1.1 # default, change as required setenv serverip 192.168.1.10 # default, change as required tftp 0x80800000 initramfs.bin bootelf $fileaddr MAC addresses: MAC address (as on device label) is stored in device info partition at an offset of 8 bytes. ath9k device has same address as ethernet, ath10k uses address incremented by 1. From stock ifconfig: ath0 Link encap:Ethernet HWaddr D8:...:2E ath10 Link encap:Ethernet HWaddr D8:...:2F br0 Link encap:Ethernet HWaddr D8:...:2E eth0 Link encap:Ethernet HWaddr D8:...:2E Signed-off-by: Paul Maruhn Co-developed-by: Philipp Rothmann Signed-off-by: Philipp Rothmann [Add pre-calibraton nvme-cells] Tested-by: Tido Klaassen Signed-off-by: Nick Hainke --- diff --git a/target/linux/ath79/dts/qca9563_tplink_eap225-outdoor-v3.dts b/target/linux/ath79/dts/qca9563_tplink_eap225-outdoor-v3.dts new file mode 100644 index 0000000000..e5914c9a55 --- /dev/null +++ b/target/linux/ath79/dts/qca9563_tplink_eap225-outdoor-v3.dts @@ -0,0 +1,59 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qca9563_tplink_eap2x5-1port.dtsi" + +/ { + compatible = "tplink,eap225-outdoor-v3", "qca,qca9563"; + model = "TP-Link EAP225-Outdoor v3"; + + aliases { + led-boot = &led_status_green; + led-failsafe = &led_status_amber; + led-running = &led_status_green; + led-upgrade = &led_status_amber; + }; + + leds { + compatible = "gpio-leds"; + + led_status_green: status_green { + label = "green:status"; + gpios = <&gpio 7 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + + led_status_amber: status_amber { + label = "amber:status"; + gpios = <&gpio 9 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&art { + precalibration_ath10k: pre-calibration@5000 { + reg = <0x5000 0x2f20>; + }; +}; + +ð0 { + phy-handle = <&phy6>; + phy-mode = "sgmii"; +}; + +&mdio0 { + phy6: ethernet-phy@6 { + reg = <6>; + }; +}; + +&pcie { + wifi@0,0 { + compatible = "qcom,ath10k"; + reg = <0 0 0 0 0>; + + mac-address-increment = <1>; + + nvmem-cells = <&macaddr_info_8>, <&precalibration_ath10k>; + nvmem-cell-names = "mac-address", "pre-calibration"; + }; +}; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index d4e956c406..209395f024 100644 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -76,6 +76,7 @@ ath79_setup_interfaces() tplink,cpe610-v2|\ tplink,cpe710-v1|\ tplink,eap225-outdoor-v1|\ + tplink,eap225-outdoor-v3|\ tplink,eap225-v1|\ tplink,eap225-v3|\ tplink,eap245-v1|\ diff --git a/target/linux/ath79/image/generic-tp-link.mk b/target/linux/ath79/image/generic-tp-link.mk index 8f4bf90b83..ffe999660a 100644 --- a/target/linux/ath79/image/generic-tp-link.mk +++ b/target/linux/ath79/image/generic-tp-link.mk @@ -401,6 +401,17 @@ define Device/tplink_eap225-outdoor-v1 endef TARGET_DEVICES += tplink_eap225-outdoor-v1 +define Device/tplink_eap225-outdoor-v3 + $(Device/tplink-eap2x5) + SOC := qca9563 + IMAGE_SIZE := 13824k + DEVICE_MODEL := EAP225-Outdoor + DEVICE_VARIANT := v3 + DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct + TPLINK_BOARD_ID := EAP225-V3 +endef +TARGET_DEVICES += tplink_eap225-outdoor-v3 + define Device/tplink_eap225-v1 $(Device/tplink-eap2x5) SOC := qca9563