From: Daniel Golle Date: Sat, 11 Mar 2023 03:56:35 +0000 (+0000) Subject: mediatek: add support for the GL.iNet GL-MT3000 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=7cbe34170e3d8471c1ebacde33a2372c92433be4;p=openwrt%2Fstaging%2Fblocktrron.git mediatek: add support for the GL.iNet GL-MT3000 The MT-3000 is a pocket-sized Wi-Fi 6 router based on MediaTek MT7981. Specification: - SoC: MediaTek MT7981B - CPU: 2x 1.3 GHz Cortex-A53 - Flash: 256 MiB Macronix SPI NAND - RAM: 512 MiB Nanya DDR4 - WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN) - Ethernet: - 1x 10/100/1000 Mbps built-in PHY (LAN) - 1x 10/100/1000/2500 Mbps MaxLinear GPY211 PHY (WAN) - USB 3.0 port - Buttons: 1 button, 1 switch - LEDs: 1x light-blue, 1x warm-white - Serial console: internal 4-pin header, 115200 8n1 - PWM controlled fan with tacho - Power: 5 VDC, 3 A (USB Type-C) Signed-off-by: Daniel Golle --- diff --git a/target/linux/mediatek/base-files/lib/preinit/05_set_preinit_iface b/target/linux/mediatek/base-files/lib/preinit/05_set_preinit_iface index 3ac856d1c4..5e7fc81ad8 100644 --- a/target/linux/mediatek/base-files/lib/preinit/05_set_preinit_iface +++ b/target/linux/mediatek/base-files/lib/preinit/05_set_preinit_iface @@ -1,11 +1,15 @@ set_preinit_iface() { - ip link set eth0 up - case $(board_name) in + glinet,gl-mt3000) + ip link set eth1 up + ifname=eth1 + ;; ubnt,unifi-6-lr) + ip link set eth0 up ifname=eth0 ;; *) + ip link set eth0 up ifname=lan1 ;; esac diff --git a/target/linux/mediatek/dts/mt7981b-glinet-gl-mt3000.dts b/target/linux/mediatek/dts/mt7981b-glinet-gl-mt3000.dts new file mode 100644 index 0000000000..d916ee49ef --- /dev/null +++ b/target/linux/mediatek/dts/mt7981b-glinet-gl-mt3000.dts @@ -0,0 +1,240 @@ +/dts-v1/; + +#include "mt7981.dtsi" + +/ { + model = "GL.iNet GL-MT3000"; + compatible = "glinet,gl-mt3000", "mediatek,mt7981"; + + aliases { + led-boot = &led_lightblue; + led-failsafe = &led_lightblue; + led-running = &led_white; + led-upgrade = &led_lightblue; + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + gpio-keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + linux,code = ; + gpios = <&pio 1 GPIO_ACTIVE_LOW>; + }; + + mode { + label = "mode"; + linux,input-type = ; + linux,code = ; + gpios = <&pio 0 GPIO_ACTIVE_HIGH>; + debounce-interval = <60>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_lightblue: led@0 { + label = "blue:run"; + gpios = <&pio 31 GPIO_ACTIVE_LOW>; + }; + + led_white: led@1 { + label = "white:system"; + gpios = <&pio 30 GPIO_ACTIVE_LOW>; + }; + }; + + fan_5v: regulator-fan-5v { + compatible = "regulator-fixed"; + regulator-name = "fan"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&pio 28 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-boot-on; + }; + + usb_vbus: regulator-usb-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&pio 12 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-boot-on; + }; +}; + +&uart0 { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +ð { + pinctrl-names = "default"; + pinctrl-0 = <&mdio_pins>; + + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "2500base-x"; + phy-handle = <&phy0>; + nvmem-cells = <&macaddr>; + nvmem-cell-names = "mac-address"; + }; + + gmac1: mac@1 { + compatible = "mediatek,eth-mac"; + reg = <1>; + phy-mode = "gmii"; + phy-handle = <&int_gbe_phy>; + nvmem-cells = <&macaddr>; + nvmem-cell-names = "mac-address"; + mac-address-increment = <1>; + }; +}; + +&mdio_bus { + reset-gpios = <&pio 14 GPIO_ACTIVE_LOW>; + reset-delay-us = <600>; + reset-post-delay-us = <20000>; + + phy0: ethernet-phy@5 { + reg = <5>; + compatible = "ethernet-phy-ieee802.3-c45"; + phy-mode = "2500base-x"; + }; +}; + +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm_pins>; + + status = "okay"; +}; + +&fan { + pwms = <&pwm 0 40000 0>; + fan-supply = <&fan_5v>; + interrupt-parent = <&pio>; + interrupts = <29 IRQ_TYPE_EDGE_RISING>; + status = "okay"; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_flash_pins>; + status = "okay"; + + spi_nand: flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spi-nand"; + reg = <0>; + spi-max-frequency = <52000000>; + + spi-cal-enable; + spi-cal-mode = "read-data"; + spi-cal-datalen = <7>; + spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4E 0x41 0x4E 0x44>; + spi-cal-addrlen = <5>; + spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>; + + spi-tx-buswidth = <4>; + spi-rx-buswidth = <4>; + mediatek,nmbm; + mediatek,bmt-max-ratio = <1>; + mediatek,bmt-max-reserved-blocks = <64>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "BL2"; + reg = <0x00000 0x0100000>; + read-only; + }; + + partition@100000 { + label = "u-boot-env"; + reg = <0x0100000 0x0080000>; + }; + + factory: partition@180000 { + label = "Factory"; + reg = <0x180000 0x0200000>; + read-only; + + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr: macaddr@a { + reg = <0xa 0x6>; + }; + }; + + partition@380000 { + label = "FIP"; + reg = <0x380000 0x0200000>; + read-only; + }; + + partition@580000 { + label = "log"; + reg = <0x580000 0x0040000>; + }; + + partition@5c0000 { + label = "ubi"; + reg = <0x5c0000 0xf640000>; + compatible = "linux,ubi"; + }; + }; + }; +}; + +&pio { + spi0_flash_pins: spi0-pins { + mux { + function = "spi"; + groups = "spi0", "spi0_wp_hold"; + }; + }; + + pwm_pins: pwm0-pins { + mux { + function = "pwm"; + groups = "pwm0_1"; + }; + }; +}; + +&usb_phy { + status = "okay"; +}; + +&xhci { + vbus-supply = <&usb_vbus>; + + status = "okay"; +}; + +&wifi { + mediatek,mtd-eeprom = <&factory 0x0>; + + status = "okay"; +}; diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network index 1bdc8337eb..63f898a9cd 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network @@ -17,6 +17,9 @@ mediatek_setup_interfaces() cudy,wr3000-v1) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" "wan" ;; + glinet,gl-mt3000) + ucidef_set_interfaces_lan_wan eth1 eth0 + ;; mediatek,mt7986a-rfb) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 lan6" "eth1 wan" ;; diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk index 821827e3ca..dcd048046c 100644 --- a/target/linux/mediatek/image/filogic.mk +++ b/target/linux/mediatek/image/filogic.mk @@ -36,6 +36,36 @@ define Build/mt7986-gpt rm $@.tmp endef +metadata_gl_json = \ + '{ $(if $(IMAGE_METADATA),$(IMAGE_METADATA)$(comma)) \ + "metadata_version": "1.1", \ + "compat_version": "$(call json_quote,$(compat_version))", \ + $(if $(DEVICE_COMPAT_MESSAGE),"compat_message": "$(call json_quote,$(DEVICE_COMPAT_MESSAGE))"$(comma)) \ + $(if $(filter-out 1.0,$(compat_version)),"new_supported_devices": \ + [$(call metadata_devices,$(SUPPORTED_DEVICES))]$(comma) \ + "supported_devices": ["$(call json_quote,$(legacy_supported_message))"]$(comma)) \ + $(if $(filter 1.0,$(compat_version)),"supported_devices":[$(call metadata_devices,$(SUPPORTED_DEVICES))]$(comma)) \ + "version": { \ + "release": "$(call json_quote,$(VERSION_NUMBER))", \ + "date": "$(shell TZ='Asia/Chongqing' date '+%Y%m%d%H%M%S')", \ + "dist": "$(call json_quote,$(VERSION_DIST))", \ + "version": "$(call json_quote,$(VERSION_NUMBER))", \ + "revision": "$(call json_quote,$(REVISION))", \ + "target": "$(call json_quote,$(TARGETID))", \ + "board": "$(call json_quote,$(if $(BOARD_NAME),$(BOARD_NAME),$(DEVICE_NAME)))" \ + }, \ + "upgrade_control":"$(shell python3 $(TOPDIR)/make_gl_metadata.py)", \ + "release_note":"$(shell sed ':a;N;s/\n/\\n/g;s/\r/\\r/g;ta' $(TOPDIR)/gl_release_note)" \ + }' + +define Build/append-gl-metadata + $(if $(SUPPORTED_DEVICES),-echo $(call metadata_gl_json,$(SUPPORTED_DEVICES)) | fwtool -I - $@) + [ ! -s "$(BUILD_KEY)" -o ! -s "$@" ] || { \ + usign -S -m "$@" -s "$(BUILD_KEY)" -x "$@.sig" ;\ + fwtool -S "$@.sig" "$@" ;\ + } +endef + define Device/asus_tuf-ax4200 DEVICE_VENDOR := ASUS DEVICE_MODEL := TUF-AX4200 @@ -52,7 +82,6 @@ define Device/asus_tuf-ax4200 endef TARGET_DEVICES += asus_tuf-ax4200 - define Device/bananapi_bpi-r3 DEVICE_VENDOR := Bananapi DEVICE_MODEL := BPi-R3 @@ -119,6 +148,22 @@ define Device/cudy_wr3000-v1 endef TARGET_DEVICES += cudy_wr3000-v1 +define Device/glinet_gl-mt3000 + DEVICE_VENDOR := GL.iNet + DEVICE_MODEL := GL-MT3000 + DEVICE_DTS := mt7981b-glinet-gl-mt3000 + DEVICE_DTS_DIR := ../dts + SUPPORTED_DEVICES += glinet,mt3000-snand + DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware kmod-hwmon-pwmfan kmod-usb3 + UBINIZE_OPTS := -E 5 + BLOCKSIZE := 128k + PAGESIZE := 2048 + IMAGE_SIZE := 246272k + KERNEL_IN_UBI := 1 + IMAGE/sysupgrade.bin := sysupgrade-tar | append-gl-metadata +endef +TARGET_DEVICES += glinet_gl-mt3000 + define Device/mediatek_mt7986a-rfb-nand DEVICE_VENDOR := MediaTek DEVICE_MODEL := MT7986 rfba AP (NAND)