From: INAGAKI Hiroshi Date: Sat, 28 Nov 2020 09:41:13 +0000 (+0900) Subject: ramips: add support for ELECOM WRC-1167GST2 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=7ba2f5c96f2697e828c28bf2daf2e4978e950207;p=openwrt%2Fstaging%2Fadrian.git ramips: add support for ELECOM WRC-1167GST2 ELECOM WRC-1167GST2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 256 MiB - Flash : SPI-NOR 32 MiB - WLAN : 2.4/5 GHz 2T2R (MediaTek MT7615D) - Ethernet : 10/100/1000 Mbps x5 - Switch : MediaTek MT7530 (SoC) - LED/keys : 6x/6x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J4: 3.3V, GND, TX, RX from ethernet port side - 57600n8 - Power : 12VDC, 1A MAC addresses: LAN : 04:AB:18:**:**:07 (Factory, 0xE000 (hex)) WAN : 04:AB:18:**:**:08 (Factory, 0xE006 (hex)) 2.4 GHz : 04:AB:18:**:**:09 (none) 5 GHz : 04:AB:18:**:**:0A (none) Flash instruction using factory image: 1. Boot WRC-1167GST2 normally 2. Access to "http://192.168.2.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click apply ("適用") button 4. Wait ~150 seconds to complete flashing Notes: - there is no way to configure the correct MAC address for secondary phy (5GHz) on MT7615D - Wi-Fi band on primary phy (2.4GHz) cannot be limitted by specifying ieee80211-freq-limit (fail to register secondary phy due to error) - mtd-mac-address in the wifi node is required for using mtd-mac-address-increment Signed-off-by: INAGAKI Hiroshi [rebase onto split DTSI] Signed-off-by: Adrian Schmutzler --- diff --git a/target/linux/ramips/dts/mt7621_elecom_wrc-1167gst2.dts b/target/linux/ramips/dts/mt7621_elecom_wrc-1167gst2.dts new file mode 100644 index 0000000000..11b782488a --- /dev/null +++ b/target/linux/ramips/dts/mt7621_elecom_wrc-1167gst2.dts @@ -0,0 +1,53 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "mt7621_elecom_wrc-gs-1pci.dtsi" + +/ { + compatible = "elecom,wrc-1167gst2", "mediatek,mt7621-soc"; + model = "ELECOM WRC-1167GST2"; +}; + +&gmac0 { + mtd-mac-address = <&factory 0xe000>; +}; + +&wan { + mtd-mac-address = <&factory 0xe006>; +}; + +&partitions { + partition@50000 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0x50000 0x1800000>; + }; + + partition@1850000 { + label = "tm_pattern"; + reg = <0x1850000 0x400000>; + read-only; + }; + + partition@1c50000 { + label = "tm_key"; + reg = <0x1c50000 0x100000>; + read-only; + }; + + partition@1d50000 { + label = "nvram"; + reg = <0x1d50000 0xb0000>; + read-only; + }; + + partition@1e00000 { + label = "user_data"; + reg = <0x1e00000 0x200000>; + read-only; + }; +}; + +&wifi { + mtd-mac-address = <&factory 0xe006>; + mtd-mac-address-increment = <1>; +}; diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk index 7b61529584..f6b72a699d 100644 --- a/target/linux/ramips/image/mt7621.mk +++ b/target/linux/ramips/image/mt7621.mk @@ -434,6 +434,14 @@ define Device/elecom_wrc-1167gs2-b endef TARGET_DEVICES += elecom_wrc-1167gs2-b +define Device/elecom_wrc-1167gst2 + $(Device/elecom_wrc-gs) + IMAGE_SIZE := 24576k + DEVICE_MODEL := WRC-1167GST2 + ELECOM_HWNAME := WRC-1167GST2 +endef +TARGET_DEVICES += elecom_wrc-1167gst2 + define Device/elecom_wrc-1750gs $(Device/elecom_wrc-gs) IMAGE_SIZE := 11264k