From: Simon Glass Date: Mon, 31 Aug 2015 01:19:18 +0000 (-0600) Subject: arm: Remove openrd boards X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=7a2c1b13;p=project%2Fbcm63xx%2Fu-boot.git arm: Remove openrd boards These boards have not been converted to generic board by the deadline. Remove them. Signed-off-by: Simon Glass --- diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig index ed9ea8aec6..6228f5bc11 100644 --- a/arch/arm/mach-kirkwood/Kconfig +++ b/arch/arm/mach-kirkwood/Kconfig @@ -4,9 +4,6 @@ choice prompt "Marvell Kirkwood board select" optional -config TARGET_OPENRD - bool "Marvell OpenRD Board" - config TARGET_RD6281A bool "RD6281A Board" @@ -63,7 +60,6 @@ endchoice config SYS_SOC default "kirkwood" -source "board/Marvell/openrd/Kconfig" source "board/Marvell/rd6281a/Kconfig" source "board/Marvell/dreamplug/Kconfig" source "board/Marvell/guruplug/Kconfig" diff --git a/board/Marvell/openrd/Kconfig b/board/Marvell/openrd/Kconfig deleted file mode 100644 index 124b66da0f..0000000000 --- a/board/Marvell/openrd/Kconfig +++ /dev/null @@ -1,12 +0,0 @@ -if TARGET_OPENRD - -config SYS_BOARD - default "openrd" - -config SYS_VENDOR - default "Marvell" - -config SYS_CONFIG_NAME - default "openrd" - -endif diff --git a/board/Marvell/openrd/MAINTAINERS b/board/Marvell/openrd/MAINTAINERS deleted file mode 100644 index 7a189ab6d5..0000000000 --- a/board/Marvell/openrd/MAINTAINERS +++ /dev/null @@ -1,12 +0,0 @@ -OPENRD BOARD -M: Prafulla Wadaskar -S: Maintained -F: board/Marvell/openrd/ -F: include/configs/openrd.h -F: configs/openrd_base_defconfig - -OPENRD_CLIENT BOARD -#M: - -S: Maintained -F: configs/openrd_client_defconfig -F: configs/openrd_ultimate_defconfig diff --git a/board/Marvell/openrd/Makefile b/board/Marvell/openrd/Makefile deleted file mode 100644 index 8f95b7922e..0000000000 --- a/board/Marvell/openrd/Makefile +++ /dev/null @@ -1,14 +0,0 @@ -# -# (C) Copyright 2009 -# Net Insight -# Written-by: Simon Kagstrom -# -# Based on sheevaplug: -# (C) Copyright 2009 -# Marvell Semiconductor -# Written-by: Prafulla Wadaskar -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y := openrd.o diff --git a/board/Marvell/openrd/kwbimage.cfg b/board/Marvell/openrd/kwbimage.cfg deleted file mode 100644 index 8e5993715e..0000000000 --- a/board/Marvell/openrd/kwbimage.cfg +++ /dev/null @@ -1,152 +0,0 @@ -# -# (C) Copyright 2009 -# Marvell Semiconductor -# Written-by: Prafulla Wadaskar -# -# SPDX-License-Identifier: GPL-2.0+ -# -# Refer doc/README.kwbimage for more details about how-to configure -# and create kirkwood boot image -# - -# Boot Media configurations -BOOT_FROM nand -NAND_ECC_MODE default -NAND_PAGE_SIZE 0x0800 - -# SOC registers configuration using bootrom header extension -# Maximum KWBIMAGE_MAX_CONFIG configurations allowed - -# Configure RGMII-0 interface pad voltage to 1.8V -DATA 0xFFD100e0 0x1b1b1b9b - -#Dram initalization for SINGLE x16 CL=5 @ 400MHz -DATA 0xFFD01400 0x43000c30 # DDR Configuration register -# bit13-0: 0xc30 (3120 DDR2 clks refresh rate) -# bit23-14: zero -# bit24: 1= enable exit self refresh mode on DDR access -# bit25: 1 required -# bit29-26: zero -# bit31-30: 01 - -DATA 0xFFD01404 0x37543000 # DDR Controller Control Low -# bit 4: 0=addr/cmd in smame cycle -# bit 5: 0=clk is driven during self refresh, we don't care for APX -# bit 6: 0=use recommended falling edge of clk for addr/cmd -# bit14: 0=input buffer always powered up -# bit18: 1=cpu lock transaction enabled -# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0 -# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM -# bit30-28: 3 required -# bit31: 0=no additional STARTBURST delay - -DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1) -# bit3-0: TRAS lsbs -# bit7-4: TRCD -# bit11- 8: TRP -# bit15-12: TWR -# bit19-16: TWTR -# bit20: TRAS msb -# bit23-21: 0x0 -# bit27-24: TRRD -# bit31-28: TRTP - -DATA 0xFFD0140C 0x00000a33 # DDR Timing (High) -# bit6-0: TRFC -# bit8-7: TR2R -# bit10-9: TR2W -# bit12-11: TW2W -# bit31-13: zero required - -DATA 0xFFD01410 0x000000cc # DDR Address Control -# bit1-0: 00, Cs0width=x8 -# bit3-2: 11, Cs0size=1Gb -# bit5-4: 00, Cs1width=x8 -# bit7-6: 11, Cs1size=1Gb -# bit9-8: 00, Cs2width=nonexistent -# bit11-10: 00, Cs2size =nonexistent -# bit13-12: 00, Cs3width=nonexistent -# bit15-14: 00, Cs3size =nonexistent -# bit16: 0, Cs0AddrSel -# bit17: 0, Cs1AddrSel -# bit18: 0, Cs2AddrSel -# bit19: 0, Cs3AddrSel -# bit31-20: 0 required - -DATA 0xFFD01414 0x00000000 # DDR Open Pages Control -# bit0: 0, OpenPage enabled -# bit31-1: 0 required - -DATA 0xFFD01418 0x00000000 # DDR Operation -# bit3-0: 0x0, DDR cmd -# bit31-4: 0 required - -DATA 0xFFD0141C 0x00000C52 # DDR Mode -# bit2-0: 2, BurstLen=2 required -# bit3: 0, BurstType=0 required -# bit6-4: 4, CL=5 -# bit7: 0, TestMode=0 normal -# bit8: 0, DLL reset=0 normal -# bit11-9: 6, auto-precharge write recovery ???????????? -# bit12: 0, PD must be zero -# bit31-13: 0 required - -DATA 0xFFD01420 0x00000042 # DDR Extended Mode -# bit0: 0, DDR DLL enabled -# bit1: 1, DDR drive strength reduced -# bit2: 0, DDR ODT control lsd (disabled) -# bit5-3: 000, required -# bit6: 1, DDR ODT control msb, (disabled) -# bit9-7: 000, required -# bit10: 0, differential DQS enabled -# bit11: 0, required -# bit12: 0, DDR output buffer enabled -# bit31-13: 0 required - -DATA 0xFFD01424 0x0000F17F # DDR Controller Control High -# bit2-0: 111, required -# bit3 : 1 , MBUS Burst Chop disabled -# bit6-4: 111, required -# bit7 : 0 -# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz -# bit9 : 0 , no half clock cycle addition to dataout -# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals -# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh -# bit15-12: 1111 required -# bit31-16: 0 required - -DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values) -DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values) - -DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 -DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size -# bit0: 1, Window enabled -# bit1: 0, Write Protect disabled -# bit3-2: 00, CS0 hit selected -# bit23-4: ones, required -# bit31-24: 0x0F, Size (i.e. 256MB) - -DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb -DATA 0xFFD0150C 0x0FFFFFF5 # CS[1]n Size 256Mb Window enabled for CS1 - -DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled -DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled - -DATA 0xFFD01494 0x00120012 # DDR ODT Control (Low) -# bit3-0: 0010, (read) M_ODT[0] is asserted during read from DRAM CS1 -# bit7-4: 0001, (read) M_ODT[1] is asserted during read from DRAM CS0 -# bit19-16: 0010, (write) M_ODT[0] is asserted during write to DRAM CS1. -# bit23-20: 0001, (write) M_ODT[1] is asserted during write to DRAM CS0. -DATA 0xFFD01498 0x00000000 # DDR ODT Control (High) - -DATA 0xFFD0149C 0x0000E40f # CPU ODT Control -# bit3-0: 1111, internal ODT is asserted during read from DRAM bank 0-3 -# bit11-10: 01, M_DQ, M_DM, and M_DQS I/O buffer ODT Select: 150 ohm -# bit13-12: 10, M_STARTBURST_IN I/O buffer ODT Select: 75 ohm -# bit14: 1, M_STARTBURST_IN ODT: Enabled -# bit15: 1, DDR IO ODT Unit: Use ODT block -DATA 0xFFD01480 0x00000001 # DDR Initialization Control -#bit0=1, enable DDR init upon this register write - -# End of Header extension -DATA 0x0 0x0 diff --git a/board/Marvell/openrd/openrd.c b/board/Marvell/openrd/openrd.c deleted file mode 100644 index 55cf525cf8..0000000000 --- a/board/Marvell/openrd/openrd.c +++ /dev/null @@ -1,161 +0,0 @@ -/* - * (C) Copyright 2009 - * Net Insight - * Written-by: Simon Kagstrom - * - * Based on sheevaplug.c: - * (C) Copyright 2009 - * Marvell Semiconductor - * Written-by: Prafulla Wadaskar - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include -#include -#include "openrd.h" - -DECLARE_GLOBAL_DATA_PTR; - -int board_early_init_f(void) -{ - /* - * default gpio configuration - * There are maximum 64 gpios controlled through 2 sets of registers - * the below configuration configures mainly initial LED status - */ - mvebu_config_gpio(OPENRD_OE_VAL_LOW, - OPENRD_OE_VAL_HIGH, - OPENRD_OE_LOW, OPENRD_OE_HIGH); - - /* Multi-Purpose Pins Functionality configuration */ - static const u32 kwmpp_config[] = { - MPP0_NF_IO2, - MPP1_NF_IO3, - MPP2_NF_IO4, - MPP3_NF_IO5, - MPP4_NF_IO6, - MPP5_NF_IO7, - MPP6_SYSRST_OUTn, - MPP7_GPO, - MPP8_TW_SDA, - MPP9_TW_SCK, - MPP10_UART0_TXD, - MPP11_UART0_RXD, - MPP12_SD_CLK, - MPP13_SD_CMD, /* Alt UART1_TXD */ - MPP14_SD_D0, /* Alt UART1_RXD */ - MPP15_SD_D1, - MPP16_SD_D2, - MPP17_SD_D3, - MPP18_NF_IO0, - MPP19_NF_IO1, - MPP20_GE1_0, - MPP21_GE1_1, - MPP22_GE1_2, - MPP23_GE1_3, - MPP24_GE1_4, - MPP25_GE1_5, - MPP26_GE1_6, - MPP27_GE1_7, - MPP28_GPIO, - MPP29_TSMP9, - MPP30_GE1_10, - MPP31_GE1_11, - MPP32_GE1_12, - MPP33_GE1_13, - MPP34_GPIO, /* UART1 / SD sel */ - MPP35_TDM_CH0_TX_QL, - MPP36_TDM_SPI_CS1, - MPP37_TDM_CH2_TX_QL, - MPP38_TDM_CH2_RX_QL, - MPP39_AUDIO_I2SBCLK, - MPP40_AUDIO_I2SDO, - MPP41_AUDIO_I2SLRC, - MPP42_AUDIO_I2SMCLK, - MPP43_AUDIO_I2SDI, - MPP44_AUDIO_EXTCLK, - MPP45_TDM_PCLK, - MPP46_TDM_FS, - MPP47_TDM_DRX, - MPP48_TDM_DTX, - MPP49_TDM_CH0_RX_QL, - 0 - }; - - kirkwood_mpp_conf(kwmpp_config, NULL); - return 0; -} - -int board_init(void) -{ - /* - * arch number of board - */ -#if defined(CONFIG_BOARD_IS_OPENRD_BASE) - gd->bd->bi_arch_number = MACH_TYPE_OPENRD_BASE; -#elif defined(CONFIG_BOARD_IS_OPENRD_CLIENT) - gd->bd->bi_arch_number = MACH_TYPE_OPENRD_CLIENT; -#elif defined(CONFIG_BOARD_IS_OPENRD_ULTIMATE) - gd->bd->bi_arch_number = MACH_TYPE_OPENRD_ULTIMATE; -#endif - - /* adress of boot parameters */ - gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100; - return 0; -} - -#ifdef CONFIG_RESET_PHY_R -/* Configure and enable MV88E1116/88E1121 PHY */ -void mv_phy_init(char *name) -{ - u16 reg; - u16 devadr; - - if (miiphy_set_current_dev(name)) - return; - - /* command to read PHY dev address */ - if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) { - printf("Err..%s could not read PHY dev address\n", - __FUNCTION__); - return; - } - - /* - * Enable RGMII delay on Tx and Rx for CPU port - * Ref: sec 4.7.2 of chip datasheet - */ - miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2); - miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®); - reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL); - miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg); - miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0); - - /* reset the phy */ - miiphy_reset(name, devadr); - - printf(PHY_NO" Initialized on %s\n", name); -} - -void reset_phy(void) -{ - mv_phy_init("egiga0"); - -#ifdef CONFIG_BOARD_IS_OPENRD_CLIENT - /* Kirkwood ethernet driver is written with the assumption that in case - * of multiple PHYs, their addresses are consecutive. But unfortunately - * in case of OpenRD-Client, PHY addresses are not consecutive.*/ - miiphy_write("egiga1", 0xEE, 0xEE, 24); -#endif - -#if defined(CONFIG_BOARD_IS_OPENRD_CLIENT) || \ - defined(CONFIG_BOARD_IS_OPENRD_ULTIMATE) - /* configure and initialize both PHY's */ - mv_phy_init("egiga1"); -#endif -} -#endif /* CONFIG_RESET_PHY_R */ diff --git a/board/Marvell/openrd/openrd.h b/board/Marvell/openrd/openrd.h deleted file mode 100644 index 56dfeea1a8..0000000000 --- a/board/Marvell/openrd/openrd.h +++ /dev/null @@ -1,30 +0,0 @@ -/* - * (C) Copyright 2009 - * Net Insight - * Written-by: Simon Kagstrom - * - * Based on sheevaplug.h: - * (C) Copyright 2009 - * Marvell Semiconductor - * Written-by: Prafulla Wadaskar - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __OPENRD_BASE_H -#define __OPENRD_BASE_H - -#define OPENRD_OE_LOW (~(1<<28)) /* RS232 / RS485 */ -#define OPENRD_OE_HIGH (~(1<<2)) /* SD / UART1 */ -#define OPENRD_OE_VAL_LOW (0) /* Sel RS232 */ -#define OPENRD_OE_VAL_HIGH (1 << 2) /* Sel SD */ - -/* PHY related */ -#define MV88E1116_LED_FCTRL_REG 10 -#define MV88E1116_CPRSP_CR3_REG 21 -#define MV88E1116_MAC_CTRL_REG 21 -#define MV88E1116_PGADR_REG 22 -#define MV88E1116_RGMII_TXTM_CTRL (1 << 4) -#define MV88E1116_RGMII_RXTM_CTRL (1 << 5) - -#endif /* __OPENRD_BASE_H */ diff --git a/configs/openrd_base_defconfig b/configs/openrd_base_defconfig deleted file mode 100644 index 16861397c3..0000000000 --- a/configs/openrd_base_defconfig +++ /dev/null @@ -1,7 +0,0 @@ -CONFIG_ARM=y -CONFIG_KIRKWOOD=y -CONFIG_TARGET_OPENRD=y -CONFIG_SYS_EXTRA_OPTIONS="BOARD_IS_OPENRD_BASE" -# CONFIG_CMD_IMLS is not set -# CONFIG_CMD_FLASH is not set -# CONFIG_CMD_SETEXPR is not set diff --git a/configs/openrd_client_defconfig b/configs/openrd_client_defconfig deleted file mode 100644 index c34231560c..0000000000 --- a/configs/openrd_client_defconfig +++ /dev/null @@ -1,7 +0,0 @@ -CONFIG_ARM=y -CONFIG_KIRKWOOD=y -CONFIG_TARGET_OPENRD=y -CONFIG_SYS_EXTRA_OPTIONS="BOARD_IS_OPENRD_CLIENT" -# CONFIG_CMD_IMLS is not set -# CONFIG_CMD_FLASH is not set -# CONFIG_CMD_SETEXPR is not set diff --git a/configs/openrd_ultimate_defconfig b/configs/openrd_ultimate_defconfig deleted file mode 100644 index 530ba4d10c..0000000000 --- a/configs/openrd_ultimate_defconfig +++ /dev/null @@ -1,7 +0,0 @@ -CONFIG_ARM=y -CONFIG_KIRKWOOD=y -CONFIG_TARGET_OPENRD=y -CONFIG_SYS_EXTRA_OPTIONS="BOARD_IS_OPENRD_ULTIMATE" -# CONFIG_CMD_IMLS is not set -# CONFIG_CMD_FLASH is not set -# CONFIG_CMD_SETEXPR is not set diff --git a/include/configs/openrd.h b/include/configs/openrd.h deleted file mode 100644 index 72113144b3..0000000000 --- a/include/configs/openrd.h +++ /dev/null @@ -1,137 +0,0 @@ -/* - * (C) Copyright 2009 - * Net Insight - * Written-by: Simon Kagstrom - * - * Based on sheevaplug.h: - * (C) Copyright 2009 - * Marvell Semiconductor - * Written-by: Prafulla Wadaskar - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef _CONFIG_OPENRD_H -#define _CONFIG_OPENRD_H - -/* - * Version number information - */ -#ifdef CONFIG_BOARD_IS_OPENRD_ULTIMATE -# define CONFIG_IDENT_STRING "\nOpenRD-Ultimate" -#else -# ifdef CONFIG_BOARD_IS_OPENRD_CLIENT -# define CONFIG_IDENT_STRING "\nOpenRD-Client" -# else -# ifdef CONFIG_BOARD_IS_OPENRD_BASE -# define CONFIG_IDENT_STRING "\nOpenRD-Base" -# else -# error Unknown OpenRD board specified -# endif -# endif -#endif - -/* - * High Level Configuration Options (easy to change) - */ -#define CONFIG_SHEEVA_88SV131 1 /* CPU Core subversion */ -#define CONFIG_KW88F6281 1 /* SOC Name */ -#define CONFIG_MACH_OPENRD_BASE /* Machine type */ -#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ - -/* - * Commands configuration - */ -#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */ -#define CONFIG_SYS_MVFS -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_ENV -#define CONFIG_CMD_MII -#define CONFIG_CMD_MMC -#define CONFIG_CMD_NAND -#define CONFIG_CMD_PING -#define CONFIG_CMD_USB -#define CONFIG_CMD_IDE - -/* - * mv-common.h should be defined after CMD configs since it used them - * to enable certain macros - */ -#include "mv-common.h" - -/* - * Environment variables configurations - */ -#ifdef CONFIG_CMD_NAND -#define CONFIG_ENV_IS_IN_NAND 1 -#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */ -#else -#define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */ -#endif -/* - * max 4k env size is enough, but in case of nand - * it has to be rounded to sector size - */ -#define CONFIG_ENV_SIZE 0x20000 /* 128k */ -#define CONFIG_ENV_ADDR 0x60000 -#define CONFIG_ENV_OFFSET 0x60000 /* env starts here */ -/* - * Environment is right behind U-Boot in flash. Make sure U-Boot - * doesn't grow into the environment area. - */ -#define CONFIG_BOARD_SIZE_LIMIT CONFIG_ENV_OFFSET - -/* - * Default environment variables - */ -#define CONFIG_BOOTCOMMAND "${x_bootcmd_kernel}; " \ - "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \ - "${x_bootcmd_usb}; bootm 0x6400000;" - -#define MTDIDS_DEFAULT "nand0=nand_mtd" -#define MTDPARTS_DEFAULT "mtdparts=nand_mtd:0x100000@0x000000(uboot),"\ - "0x400000@0x100000(uImage),"\ - "0x1fb00000@0x500000(rootfs)" - -#define CONFIG_EXTRA_ENV_SETTINGS "x_bootargs=console" \ - "=ttyS0,115200 "MTDPARTS_DEFAULT " rw ubi.mtd=2,2048\0" \ - "x_bootcmd_kernel=nand read 0x6400000 0x100000 0x300000\0" \ - "x_bootcmd_usb=usb start\0" \ - "x_bootargs_root=root=ubi0:rootfs rootfstype=ubifs\0" \ - "mtdids="MTDIDS_DEFAULT"\0" \ - "mtdparts="MTDPARTS_DEFAULT"\0" - -/* - * Ethernet Driver configuration - */ -#ifdef CONFIG_CMD_NET -# ifdef CONFIG_BOARD_IS_OPENRD_BASE -# define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */ -# else -# define CONFIG_MVGBE_PORTS {1, 1} /* enable both ports */ -# endif -# ifdef CONFIG_BOARD_IS_OPENRD_ULTIMATE -# define CONFIG_PHY_BASE_ADR 0x0 -# define PHY_NO "88E1121" -# else -# define CONFIG_PHY_BASE_ADR 0x8 -# define PHY_NO "88E1116" -# endif -#endif /* CONFIG_CMD_NET */ - -/* - * SATA Driver configuration - */ -#ifdef CONFIG_MVSATA_IDE -#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET -#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET -#endif /*CONFIG_MVSATA_IDE*/ - -#ifdef CONFIG_CMD_MMC -#define CONFIG_MMC -#define CONFIG_GENERIC_MMC -#define CONFIG_MVEBU_MMC -#define CONFIG_SYS_MMC_BASE KW_SDIO_BASE -#endif /* CONFIG_CMD_MMC */ - -#endif /* _CONFIG_OPENRD_BASE_H */