From: John Crispin Date: Tue, 19 Jan 2016 10:16:36 +0000 (+0000) Subject: ipq806x: Add support for Netgear D7800 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=78a6a9aec306f3fa53b3eaffb35a2344c26a43c7;p=openwrt%2Fstaging%2Fjow.git ipq806x: Add support for Netgear D7800 Signed-off-by: Tathagata Das SVN-Revision: 48360 --- diff --git a/target/linux/ipq806x/base-files/etc/board.d/01_leds b/target/linux/ipq806x/base-files/etc/board.d/01_leds index 07b5b06988..b32c1cc21d 100755 --- a/target/linux/ipq806x/base-files/etc/board.d/01_leds +++ b/target/linux/ipq806x/base-files/etc/board.d/01_leds @@ -11,6 +11,7 @@ board_config_update board=$(ipq806x_board_name) case "$board" in +d7800 |\ r7500) ucidef_set_led_usbdev "usb1" "USB 1" "r7500:white:usb1" "1-1" ucidef_set_led_usbdev "usb2" "USB 2" "r7500:white:usb3" "3-1" diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network index 1302a559f1..6e18297e99 100755 --- a/target/linux/ipq806x/base-files/etc/board.d/02_network +++ b/target/linux/ipq806x/base-files/etc/board.d/02_network @@ -13,6 +13,7 @@ board=$(ipq806x_board_name) case "$board" in ap148 |\ +d7800 |\ r7500) ucidef_add_switch "switch0" \ "1:lan" "2:lan" "3:lan" "4:lan" "6@eth1" "5:wan" "0@eth0" diff --git a/target/linux/ipq806x/base-files/lib/ipq806x.sh b/target/linux/ipq806x/base-files/lib/ipq806x.sh index 5b27bde758..db227087f4 100644 --- a/target/linux/ipq806x/base-files/lib/ipq806x.sh +++ b/target/linux/ipq806x/base-files/lib/ipq806x.sh @@ -17,6 +17,9 @@ ipq806x_board_detect() { *"AP148") name="ap148" ;; + *"D7800") + name="d7800" + ;; *"DB149") name="db149" ;; diff --git a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh index 7fcf246020..542b5cecde 100644 --- a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh @@ -7,6 +7,7 @@ platform_check_image() { case "$board" in ap148 |\ + d7800 |\ r7500) nand_do_platform_check $board $1 return $?; @@ -21,6 +22,7 @@ platform_pre_upgrade() { case "$board" in ap148 |\ + d7800 |\ r7500) nand_do_upgrade "$1" ;; diff --git a/target/linux/ipq806x/image/Makefile b/target/linux/ipq806x/image/Makefile index 58c4e1e872..ff8b2c7d9b 100644 --- a/target/linux/ipq806x/image/Makefile +++ b/target/linux/ipq806x/image/Makefile @@ -104,6 +104,17 @@ define Device/AP148-legacy BOARD_NAME := ap148 endef +define Device/D7800 + $(call Device/DniImage) + DEVICE_DTS := qcom-ipq8064-d7800 + KERNEL_SIZE := 2097152 + NETGEAR_BOARD_ID := D7800 + NETGEAR_HW_ID := 29764958+0+128+512+4x4+4x4 + BLOCKSIZE := 128KiB + PAGESIZE := 2048 + BOARD_NAME := d7800 +endef + define Device/DB149 $(call Device/FitImage) DEVICE_DTS := qcom-ipq8064-db149 @@ -122,6 +133,6 @@ define Device/R7500 BOARD_NAME := r7500 endef -TARGET_DEVICES += AP148 AP148-legacy DB149 R7500 +TARGET_DEVICES += AP148 AP148-legacy D7800 DB149 R7500 $(eval $(call BuildImage)) diff --git a/target/linux/ipq806x/patches-3.18/801-ARM-qcom-add-Netgear-Nighthawk-X4-D7800-device-tree.patch b/target/linux/ipq806x/patches-3.18/801-ARM-qcom-add-Netgear-Nighthawk-X4-D7800-device-tree.patch new file mode 100644 index 0000000000..ecc1cff9df --- /dev/null +++ b/target/linux/ipq806x/patches-3.18/801-ARM-qcom-add-Netgear-Nighthawk-X4-D7800-device-tree.patch @@ -0,0 +1,381 @@ +--- a/arch/arm/boot/dts/Makefile 2015-09-22 18:30:09.033530282 +0530 ++++ b/arch/arm/boot/dts/Makefile 2015-09-23 17:06:44.892947581 +0530 +@@ -362,6 +362,7 @@ + qcom-ipq8064-ap148.dtb \ + qcom-ipq8064-db149.dtb \ + qcom-ipq8064-r7500.dtb \ ++ qcom-ipq8064-d7800.dtb \ + qcom-msm8660-surf.dtb \ + qcom-msm8960-cdp.dtb \ + qcom-msm8974-sony-xperia-honami.dtb +--- a/arch/arm/boot/dts/qcom-ipq8064-d7800.dts 1970-01-01 05:30:00.000000000 +0530 ++++ b/arch/arm/boot/dts/qcom-ipq8064-d7800.dts 2015-09-23 17:06:45.336947567 +0530 +@@ -0,0 +1,368 @@ ++#include "qcom-ipq8064-v1.0.dtsi" ++ ++#include ++ ++/ { ++ model = "Netgear Nighthawk X4 D7800"; ++ compatible = "netgear,d7800", "qcom,ipq8064"; ++ ++ memory@0 { ++ reg = <0x42000000 0xe000000>; ++ device_type = "memory"; ++ }; ++ ++ reserved-memory { ++ #address-cells = <1>; ++ #size-cells = <1>; ++ ranges; ++ rsvd@41200000 { ++ reg = <0x41200000 0x300000>; ++ no-map; ++ }; ++ }; ++ ++ aliases { ++ serial0 = &uart4; ++ mdio-gpio0 = &mdio0; ++ }; ++ ++ chosen { ++ bootargs = "rootfstype=squashfs noinitrd"; ++ linux,stdout-path = "serial0:115200n8"; ++ }; ++ ++ soc { ++ pinmux@800000 { ++ i2c4_pins: i2c4_pinmux { ++ pins = "gpio12", "gpio13"; ++ function = "gsbi4"; ++ bias-disable; ++ }; ++ ++ pcie0_pins: pcie0_pinmux { ++ mux { ++ pins = "gpio3"; ++ function = "pcie1_rst"; ++ drive-strength = <12>; ++ bias-disable; ++ }; ++ }; ++ ++ pcie1_pins: pcie1_pinmux { ++ mux { ++ pins = "gpio48"; ++ function = "pcie2_rst"; ++ drive-strength = <12>; ++ bias-disable; ++ }; ++ }; ++ ++ nand_pins: nand_pins { ++ mux { ++ pins = "gpio34", "gpio35", "gpio36", ++ "gpio37", "gpio38", "gpio39", ++ "gpio40", "gpio41", "gpio42", ++ "gpio43", "gpio44", "gpio45", ++ "gpio46", "gpio47"; ++ function = "nand"; ++ drive-strength = <10>; ++ bias-disable; ++ }; ++ pullups { ++ pins = "gpio39"; ++ bias-pull-up; ++ }; ++ hold { ++ pins = "gpio40", "gpio41", "gpio42", ++ "gpio43", "gpio44", "gpio45", ++ "gpio46", "gpio47"; ++ bias-bus-hold; ++ }; ++ }; ++ ++ mdio0_pins: mdio0_pins { ++ mux { ++ pins = "gpio0", "gpio1"; ++ function = "gpio"; ++ drive-strength = <8>; ++ bias-disable; ++ }; ++ }; ++ ++ rgmii2_pins: rgmii2_pins { ++ mux { ++ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", ++ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; ++ function = "rgmii2"; ++ drive-strength = <8>; ++ bias-disable; ++ }; ++ }; ++ }; ++ ++ gsbi@16300000 { ++ qcom,mode = ; ++ status = "ok"; ++ serial@16340000 { ++ status = "ok"; ++ }; ++ /* ++ * The i2c device on gsbi4 should not be enabled. ++ * On ipq806x designs gsbi4 i2c is meant for exclusive ++ * RPM usage. Turning this on in kernel manifests as ++ * i2c failure for the RPM. ++ */ ++ }; ++ ++ sata-phy@1b400000 { ++ status = "ok"; ++ }; ++ ++ sata@29000000 { ++ status = "ok"; ++ }; ++ ++ phy@100f8800 { /* USB3 port 1 HS phy */ ++ status = "ok"; ++ }; ++ ++ phy@100f8830 { /* USB3 port 1 SS phy */ ++ status = "ok"; ++ }; ++ ++ phy@110f8800 { /* USB3 port 0 HS phy */ ++ status = "ok"; ++ }; ++ ++ phy@110f8830 { /* USB3 port 0 SS phy */ ++ status = "ok"; ++ }; ++ ++ usb30@0 { ++ status = "ok"; ++ }; ++ ++ usb30@1 { ++ status = "ok"; ++ }; ++ ++ pcie0: pci@1b500000 { ++ status = "ok"; ++ reset-gpio = <&qcom_pinmux 3 0>; ++ pinctrl-0 = <&pcie0_pins>; ++ pinctrl-names = "default"; ++ }; ++ ++ pcie1: pci@1b700000 { ++ status = "ok"; ++ reset-gpio = <&qcom_pinmux 48 0>; ++ pinctrl-0 = <&pcie1_pins>; ++ pinctrl-names = "default"; ++ }; ++ ++ nand@1ac00000 { ++ status = "ok"; ++ ++ pinctrl-0 = <&nand_pins>; ++ pinctrl-names = "default"; ++ ++ nand-ecc-strength = <4>; ++ nand-bus-width = <8>; ++ ++ #address-cells = <1>; ++ #size-cells = <1>; ++ ++ qcadata@0 { ++ label = "qcadata"; ++ reg = <0x0000000 0x0c80000>; ++ read-only; ++ }; ++ ++ APPSBL@c80000 { ++ label = "APPSBL"; ++ reg = <0x0c80000 0x0500000>; ++ read-only; ++ }; ++ ++ APPSBLENV@1180000 { ++ label = "APPSBLENV"; ++ reg = <0x1180000 0x0080000>; ++ read-only; ++ }; ++ ++ art: art@1200000 { ++ label = "art"; ++ reg = <0x1200000 0x0140000>; ++ read-only; ++ }; ++ ++ artbak: art@1340000 { ++ label = "artbak"; ++ reg = <0x1340000 0x0140000>; ++ read-only; ++ }; ++ ++ kernel@1480000 { ++ label = "kernel"; ++ reg = <0x1480000 0x0200000>; ++ }; ++ ++ ubi@1680000 { ++ label = "ubi"; ++ reg = <0x1680000 0x1E00000>; ++ }; ++ ++ netgear@3480000 { ++ label = "netgear"; ++ reg = <0x3480000 0x4480000>; ++ read-only; ++ }; ++ ++ reserve@7900000 { ++ label = "reserve"; ++ reg = <0x7900000 0x0700000>; ++ read-only; ++ }; ++ ++ firmware@1480000 { ++ label = "firmware"; ++ reg = <0x1480000 0x2000000>; ++ }; ++ ++ }; ++ ++ mdio0: mdio { ++ compatible = "virtual,mdio-gpio"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>; ++ pinctrl-0 = <&mdio0_pins>; ++ pinctrl-names = "default"; ++ ++ phy0: ethernet-phy@0 { ++ device_type = "ethernet-phy"; ++ reg = <0>; ++ qca,ar8327-initvals = < ++ 0x00004 0x7600000 /* PAD0_MODE */ ++ 0x00008 0x1000000 /* PAD5_MODE */ ++ 0x0000c 0x80 /* PAD6_MODE */ ++ 0x000e4 0xaa545 /* MAC_POWER_SEL */ ++ 0x000e0 0xc74164de /* SGMII_CTRL */ ++ 0x0007c 0x4e /* PORT0_STATUS */ ++ 0x00094 0x4e /* PORT6_STATUS */ ++ >; ++ }; ++ ++ phy4: ethernet-phy@4 { ++ device_type = "ethernet-phy"; ++ reg = <4>; ++ }; ++ }; ++ ++ gmac1: ethernet@37200000 { ++ status = "ok"; ++ phy-mode = "rgmii"; ++ phy-handle = <&phy4>; ++ qcom,id = <1>; ++ ++ pinctrl-0 = <&rgmii2_pins>; ++ pinctrl-names = "default"; ++ ++ mtd-mac-address = <&art 6>; ++ }; ++ ++ gmac2: ethernet@37400000 { ++ status = "ok"; ++ phy-mode = "sgmii"; ++ qcom,id = <2>; ++ ++ mtd-mac-address = <&art 0>; ++ ++ fixed-link { ++ speed = <1000>; ++ full-duplex; ++ }; ++ }; ++ }; ++ ++ gpio-keys { ++ compatible = "gpio-keys"; ++ ++ wifi { ++ label = "wifi"; ++ gpios = <&qcom_pinmux 6 1>; ++ linux,code = ; ++ }; ++ ++ reset { ++ label = "reset"; ++ gpios = <&qcom_pinmux 54 1>; ++ linux,code = ; ++ }; ++ ++ wps { ++ label = "wps"; ++ gpios = <&qcom_pinmux 65 1>; ++ linux,code = ; ++ }; ++ }; ++ ++ gpio-leds { ++ compatible = "gpio-leds"; ++ ++ usb1 { ++ label = "d7800:amber:usb1"; ++ gpios = <&qcom_pinmux 7 0>; ++ }; ++ ++ usb3 { ++ label = "d7800:amber:usb3"; ++ gpios = <&qcom_pinmux 8 0>; ++ }; ++ ++ status { ++ label = "d7800:amber:status"; ++ gpios = <&qcom_pinmux 9 0>; ++ }; ++ ++ internet { ++ label = "d7800:white:internet"; ++ gpios = <&qcom_pinmux 22 0>; ++ }; ++ ++ wan { ++ label = "d7800:white:wan"; ++ gpios = <&qcom_pinmux 23 0>; ++ }; ++ ++ wps { ++ label = "d7800:white:wps"; ++ gpios = <&qcom_pinmux 24 0>; ++ }; ++ ++ esata { ++ label = "d7800:white:esata"; ++ gpios = <&qcom_pinmux 26 0>; ++ }; ++ ++ power { ++ label = "d7800:white:power"; ++ gpios = <&qcom_pinmux 53 0>; ++ default-state = "on"; ++ }; ++ ++ rfkill { ++ label = "d7800:white:rfkill"; ++ gpios = <&qcom_pinmux 64 0>; ++ }; ++ ++ wifi5g { ++ label = "d7800:white:wifi5g"; ++ gpios = <&qcom_pinmux 67 0>; ++ }; ++ }; ++}; ++ ++&adm_dma { ++ status = "ok"; ++}; diff --git a/target/linux/ipq806x/profiles/netgear.mk b/target/linux/ipq806x/profiles/netgear.mk index 3402f45853..25258cdca3 100644 --- a/target/linux/ipq806x/profiles/netgear.mk +++ b/target/linux/ipq806x/profiles/netgear.mk @@ -6,6 +6,18 @@ # See /LICENSE for more information. # +define Profile/D7800 + NAME:=Netgear Nighthawk X4 D7800 + PACKAGES:= \ + kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-ledtrig-usbdev \ + kmod-usb3 kmod-usb-dwc3-qcom kmod-usb-phy-qcom-dwc3 \ + kmod-ath10k wpad-mini ath10k-firmware-qca99x0 +endef + +define Profile/D7800/Description + Package set for the Netgear Nighthawk X4 D7800. +endef + define Profile/R7500 NAME:=Netgear Nighthawk X4 R7500 PACKAGES:= \ @@ -17,4 +29,5 @@ endef define Profile/R7500/Description Package set for the Netgear Nighthawk X4 R7500. endef +$(eval $(call Profile,D7800)) $(eval $(call Profile,R7500))