From: Imre Kaloz Date: Thu, 10 May 2007 11:00:02 +0000 (+0000) Subject: preliminary board support for the Linksys WRT300N v2 (incomplete) X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=73c3a907a3f5b442028a99c71c9bcd4e9070cec8;p=openwrt%2Fstaging%2Fneocturne.git preliminary board support for the Linksys WRT300N v2 (incomplete) SVN-Revision: 7167 --- diff --git a/scripts/arm-magic.sh b/scripts/arm-magic.sh index 9b48841cd1..155a6c9d45 100755 --- a/scripts/arm-magic.sh +++ b/scripts/arm-magic.sh @@ -22,7 +22,7 @@ # NOTE: for now it's for only IXP4xx in big endian mode # list of supported boards, in "boardname machtypeid" format -for board in "avila 526" "gateway7001 731" "nslu2 597" "nas100d 865" "wg302v2 890" "pronghornmetro 1040" "compex 1273" +for board in "avila 526" "gateway7001 731" "nslu2 597" "nas100d 865" "wg302v2 890" "pronghornmetro 1040" "compex 1273" "wrt300nv2 1077" do set -- $board hexid=$(printf %x\\n $2) diff --git a/target/linux/ixp4xx-2.6/config/default b/target/linux/ixp4xx-2.6/config/default index c3fd3b3ebc..41396f8232 100644 --- a/target/linux/ixp4xx-2.6/config/default +++ b/target/linux/ixp4xx-2.6/config/default @@ -220,6 +220,7 @@ CONFIG_MACH_NAS100D=y CONFIG_MACH_NSLU2=y CONFIG_MACH_PRONGHORNMETRO=y CONFIG_MACH_WG302V2=y +CONFIG_MACH_WRT300NV2=y # CONFIG_MAC_PARTITION is not set # CONFIG_MINIX_FS is not set CONFIG_MINI_FO=y @@ -231,7 +232,7 @@ CONFIG_MTD_BLOCK=y # CONFIG_MTD_BLOCK2MTD is not set CONFIG_MTD_CFI=y CONFIG_MTD_CFI_ADV_OPTIONS=y -# CONFIG_MTD_CFI_AMDSTD is not set +CONFIG_MTD_CFI_AMDSTD=y # CONFIG_MTD_CFI_BE_BYTE_SWAP is not set CONFIG_MTD_CFI_GEOMETRY=n CONFIG_MTD_CFI_I1=y diff --git a/target/linux/ixp4xx-2.6/patches/600-wrt300nv2.patch b/target/linux/ixp4xx-2.6/patches/600-wrt300nv2.patch new file mode 100644 index 0000000000..459fbd0d7e --- /dev/null +++ b/target/linux/ixp4xx-2.6/patches/600-wrt300nv2.patch @@ -0,0 +1,229 @@ +diff -Nur linux-2.6.19.2/arch/arm/mach-ixp4xx/Kconfig linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/Kconfig +--- linux-2.6.19.2/arch/arm/mach-ixp4xx/Kconfig 2007-05-03 23:17:47.000000000 +0200 ++++ linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/Kconfig 2007-04-24 14:25:02.000000000 +0200 +@@ -65,6 +65,14 @@ + WP18 or NP18A boards. For more information on this + platform, see http://openwrt.org + ++config MACH_WRT300NV2 ++ bool "Linksys WRT300N v2" ++ select PCI ++ help ++ Say 'Y' here if you want your kernel to support Linksys' ++ WRT300N v2 router. For more information on this ++ platform, see http://openwrt.org ++ + config ARCH_IXDP425 + bool "IXDP425" + help +diff -Nur linux-2.6.19.2/arch/arm/mach-ixp4xx/Makefile linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/Makefile +--- linux-2.6.19.2/arch/arm/mach-ixp4xx/Makefile 2007-05-03 23:17:47.000000000 +0200 ++++ linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/Makefile 2007-04-24 14:25:02.000000000 +0200 +@@ -15,6 +15,7 @@ + obj-pci-$(CONFIG_MACH_WG302V2) += wg302v2-pci.o + obj-pci-$(CONFIG_MACH_PRONGHORNMETRO) += pronghornmetro-pci.o + obj-pci-$(CONFIG_MACH_COMPEX) += ixdp425-pci.o ++obj-pci-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-pci.o + + obj-y += common.o + +@@ -28,5 +29,6 @@ + obj-$(CONFIG_MACH_WG302V2) += wg302v2-setup.o + obj-$(CONFIG_MACH_PRONGHORNMETRO) += pronghornmetro-setup.o + obj-$(CONFIG_MACH_COMPEX) += compex-setup.o ++obj-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-setup.o + + obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o +diff -Nur linux-2.6.19.2/arch/arm/mach-ixp4xx/wrt300nv2-pci.c linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/wrt300nv2-pci.c +--- linux-2.6.19.2/arch/arm/mach-ixp4xx/wrt300nv2-pci.c 1970-01-01 01:00:00.000000000 +0100 ++++ linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/wrt300nv2-pci.c 2007-05-10 10:40:54.000000000 +0200 +@@ -0,0 +1,65 @@ ++/* ++ * arch/arch/mach-ixp4xx/wrt300nv2-pci.c ++ * ++ * PCI setup routines for Linksys WRT300N v2 ++ * ++ * Copyright (C) 2007 Imre Kaloz ++ * ++ * based on coyote-pci.c: ++ * Copyright (C) 2002 Jungo Software Technologies. ++ * Copyright (C) 2003 MontaVista Softwrae, Inc. ++ * ++ * Maintainer: Imre Kaloz ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ * ++ */ ++ ++#include ++#include ++#include ++#include ++ ++#include ++#include ++#include ++ ++#include ++ ++extern void ixp4xx_pci_preinit(void); ++extern int ixp4xx_setup(int nr, struct pci_sys_data *sys); ++extern struct pci_bus *ixp4xx_scan_bus(int nr, struct pci_sys_data *sys); ++ ++void __init wrt300nv2_pci_preinit(void) ++{ ++ set_irq_type(IRQ_IXP4XX_GPIO8, IRQT_LOW); ++ ++ ixp4xx_pci_preinit(); ++} ++ ++static int __init wrt300nv2_map_irq(struct pci_dev *dev, u8 slot, u8 pin) ++{ ++ if (slot == 1) ++ return IRQ_IXP4XX_GPIO8; ++ else return -1; ++} ++ ++struct hw_pci wrt300nv2_pci __initdata = { ++ .nr_controllers = 1, ++ .preinit = wrt300nv2_pci_preinit, ++ .swizzle = pci_std_swizzle, ++ .setup = ixp4xx_setup, ++ .scan = ixp4xx_scan_bus, ++ .map_irq = wrt300nv2_map_irq, ++}; ++ ++int __init wrt300nv2_pci_init(void) ++{ ++ if (machine_is_wrt300nv2()) ++ pci_common_init(&wrt300nv2_pci); ++ return 0; ++} ++ ++subsys_initcall(wrt300nv2_pci_init); +diff -Nur linux-2.6.19.2/arch/arm/mach-ixp4xx/wrt300nv2-setup.c linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/wrt300nv2-setup.c +--- linux-2.6.19.2/arch/arm/mach-ixp4xx/wrt300nv2-setup.c 1970-01-01 01:00:00.000000000 +0100 ++++ linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/wrt300nv2-setup.c 2007-05-03 23:16:53.000000000 +0200 +@@ -0,0 +1,108 @@ ++/* ++ * arch/arm/mach-ixp4xx/wrt300nv2-setup.c ++ * ++ * Board setup for the Linksys WRT300N v2 ++ * ++ * Copyright (C) 2007 Imre Kaloz ++ * ++ * based on coyote-setup.c: ++ * Copyright (C) 2003-2005 MontaVista Software, Inc. ++ * ++ * Author: Imre Kaloz ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++static struct flash_platform_data wrt300nv2_flash_data = { ++ .map_name = "cfi_probe", ++ .width = 2, ++}; ++ ++static struct resource wrt300nv2_flash_resource = { ++ .flags = IORESOURCE_MEM, ++}; ++ ++static struct platform_device wrt300nv2_flash = { ++ .name = "IXP4XX-Flash", ++ .id = 0, ++ .dev = { ++ .platform_data = &wrt300nv2_flash_data, ++ }, ++ .num_resources = 1, ++ .resource = &wrt300nv2_flash_resource, ++}; ++ ++static struct resource wrt300nv2_uart_resource = { ++ .start = IXP4XX_UART2_BASE_PHYS, ++ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff, ++ .flags = IORESOURCE_MEM, ++}; ++ ++static struct plat_serial8250_port wrt300nv2_uart_data[] = { ++ { ++ .mapbase = IXP4XX_UART2_BASE_PHYS, ++ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET, ++ .irq = IRQ_IXP4XX_UART2, ++ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, ++ .iotype = UPIO_MEM, ++ .regshift = 2, ++ .uartclk = IXP4XX_UART_XTAL, ++ }, ++ { }, ++}; ++ ++static struct platform_device wrt300nv2_uart = { ++ .name = "serial8250", ++ .id = PLAT8250_DEV_PLATFORM, ++ .dev = { ++ .platform_data = wrt300nv2_uart_data, ++ }, ++ .num_resources = 1, ++ .resource = &wrt300nv2_uart_resource, ++}; ++ ++static struct platform_device *wrt300nv2_devices[] __initdata = { ++ &wrt300nv2_flash, ++ &wrt300nv2_uart ++}; ++ ++static void __init wrt300nv2_init(void) ++{ ++ ixp4xx_sys_init(); ++ ++ wrt300nv2_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); ++ wrt300nv2_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1; ++ ++ *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE; ++ *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0; ++ ++ platform_add_devices(wrt300nv2_devices, ARRAY_SIZE(wrt300nv2_devices)); ++} ++ ++#ifdef CONFIG_MACH_WRT300NV2 ++MACHINE_START(WRT300NV2, "Linksys WRT300N v2") ++ /* Maintainer: Imre Kaloz */ ++ .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, ++ .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc, ++ .map_io = ixp4xx_map_io, ++ .init_irq = ixp4xx_init_irq, ++ .timer = &ixp4xx_timer, ++ .boot_params = 0x0100, ++ .init_machine = wrt300nv2_init, ++MACHINE_END ++#endif +diff -Nur linux-2.6.19.2/include/asm-arm/arch-ixp4xx/uncompress.h linux-2.6.19.2-owrt/include/asm-arm/arch-ixp4xx/uncompress.h +--- linux-2.6.19.2/include/asm-arm/arch-ixp4xx/uncompress.h 2007-05-03 23:17:48.000000000 +0200 ++++ linux-2.6.19.2-owrt/include/asm-arm/arch-ixp4xx/uncompress.h 2007-04-24 14:25:02.000000000 +0200 +@@ -40,7 +40,7 @@ + /* + * Some boards are using UART2 as console + */ +- if (machine_is_adi_coyote() || machine_is_gtwx5715() || machine_is_gateway7001() || machine_is_wg302v2() || machine_is_pronghorn() || machine_is_pronghorn_metro()) ++ if (machine_is_adi_coyote() || machine_is_gtwx5715() || machine_is_gateway7001() || machine_is_wg302v2() || machine_is_pronghorn() || machine_is_pronghorn_metro() || machine_is_wrt300nv2()) + uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS; + else + uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS; diff --git a/target/linux/ixp4xx-2.6/patches/610-wrt300nv2_setup_mac.patch b/target/linux/ixp4xx-2.6/patches/610-wrt300nv2_setup_mac.patch new file mode 100644 index 0000000000..145ad76ef7 --- /dev/null +++ b/target/linux/ixp4xx-2.6/patches/610-wrt300nv2_setup_mac.patch @@ -0,0 +1,62 @@ +diff -Nur linux-2.6.19.2/arch/arm/mach-ixp4xx/wrt300nv2-setup.c linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/wrt300nv2-setup.c +--- linux-2.6.19.2/arch/arm/mach-ixp4xx/wrt300nv2-setup.c 2007-04-24 14:25:02.000000000 +0200 ++++ linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/wrt300nv2-setup.c 2007-04-24 14:31:09.000000000 +0200 +@@ -76,9 +76,57 @@ + .resource = &wrt300nv2_uart_resource, + }; + ++static struct resource res_mac0 = { ++ .start = IXP4XX_EthB_BASE_PHYS, ++ .end = IXP4XX_EthB_BASE_PHYS + 0x1ff, ++ .flags = IORESOURCE_MEM, ++}; ++ ++static struct resource res_mac1 = { ++ .start = IXP4XX_EthC_BASE_PHYS, ++ .end = IXP4XX_EthC_BASE_PHYS + 0x1ff, ++ .flags = IORESOURCE_MEM, ++}; ++ ++static struct mac_plat_info plat_mac0 = { ++ .npe_id = 1, ++ .phy_id = -1, ++ .eth_id = 0, ++ .rxq_id = 27, ++ .txq_id = 24, ++ .rxdoneq_id = 4, ++}; ++ ++static struct mac_plat_info plat_mac1 = { ++ .npe_id = 2, ++ .phy_id = 1, ++ .eth_id = 1, ++ .rxq_id = 28, ++ .txq_id = 25, ++ .rxdoneq_id = 5, ++}; ++ ++static struct platform_device mac0 = { ++ .name = "ixp4xx_mac", ++ .id = 0, ++ .dev.platform_data = &plat_mac0, ++ .num_resources = 1, ++ .resource = &res_mac0, ++}; ++ ++static struct platform_device mac1 = { ++ .name = "ixp4xx_mac", ++ .id = 1, ++ .dev.platform_data = &plat_mac1, ++ .num_resources = 1, ++ .resource = &res_mac1, ++}; ++ + static struct platform_device *wrt300nv2_devices[] __initdata = { + &wrt300nv2_flash, +- &wrt300nv2_uart ++ &wrt300nv2_uart, ++ &mac0, ++ &mac1, + }; + + static void __init wrt300nv2_init(void)