From: Paweł Owoc Date: Fri, 24 Nov 2023 21:15:44 +0000 (+0100) Subject: qualcommax: ipq807x: add support for Linksys MX5300 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=70fd815e57dc98cef88828faa5ce71717540e99e;p=openwrt%2Fstaging%2Fstintel.git qualcommax: ipq807x: add support for Linksys MX5300 Hardware specification: ======== SoC: Qualcomm IPQ8072A Flash: 512MB (Winbond W29N04GZBIBA) RAM: 1GB (2x Nanya DDR3L NT5CC256M16ER-EK) Ethernet: 5x 10/100/1000Mbps (Qualcomm QCA8075) WiFi1: 5GHz ac 4x4 (Qualcomm QCA9984 + Skyworks SKY85746-11) - channels 100-169 WiFi2: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-64 WiFi3: 2.4GHz ax 4x4 (Qualcomm QCN5024 + Skyworks SKY8340-11) IoT: Bluetooth 5, Zigbee and Thread (Qualcomm QCA4024 + Skyworks SE2433T-R) IoT Flash: 4MB (Macronix MX25R3235F) RTC: ST M41T00S LED: 1x RGB status (NXP PCA9633) USB: 1x USB 3.0 Button: WPS, Reset Flash instructions: ======== 1. Manually upgrade firmware using openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin image. More details can be found here: https://www.linksys.com/hk/support-article?articleNum=274497 After first boot check actual partition: - fw_printenv -n boot_part and install firmware on second partition using command in case of 2: - mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin kernel and in case of 1: - mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin alt_kernel 2. Installation using serial connection from OEM firmware (default login: root, password: admin): - fw_printenv -n boot_part In case of 2: - flash_erase /dev/mtd21 0 0 nandwrite -p /dev/mtd21 openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin or in case of 1: - flash_erase /dev/mtd23 0 0 nandwrite -p /dev/mtd23 openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin After first boot install firmware on second partition: - mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin kernel or: - mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin alt_kernel 3. Installation from initramfs image using USB FAT32 formatted drive: Stop u-boot and run: - usb start && fatload usb 0:1 $loadaddr openwrt-qualcommax-ipq807x-linksys_mx5300-initramfs-uImage.itb && bootm $loadaddr Write firmware to the flash from initramfs: - mtd -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin kernel and: - mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin alt_kernel 4. Back to the OEM firmware: - mtd -e kernel -n write FW_MX5300_1.1.9.200251_prod.img kernel and: - mtd -r -e alt_kernel -n write FW_MX5300_1.1.9.200251_prod.img alt_kernel 5. USB recovery: - fw_setenv usbimage 'openwrt-qualcommax-ipq807x-linksys_mx5300-initramfs-uImage.itb' fw_setenv bootusb 'usb start && fatload usb 0:1 $loadaddr $usbimage && bootm $loadaddr' fw_setenv bootcmd 'run bootusb; aq_load_fw && if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi' Notes: ======== IoT device is accesible over spi. Not yet supported. Signed-off-by: Paweł Owoc Reviewed-by: Robert Marko --- diff --git a/package/boot/uboot-envtools/files/qualcommax_ipq807x b/package/boot/uboot-envtools/files/qualcommax_ipq807x index bcedfd9adc..86e7062cfc 100644 --- a/package/boot/uboot-envtools/files/qualcommax_ipq807x +++ b/package/boot/uboot-envtools/files/qualcommax_ipq807x @@ -30,7 +30,8 @@ edimax,cax1800) ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x10000" "0x20000" ;; linksys,mx4200v1|\ -linksys,mx4200v2) +linksys,mx4200v2|\ +linksys,mx5300) idx="$(find_mtd_index u_env)" [ -n "$idx" ] && \ ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x40000" "0x20000" "2" diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile index 2b53d3e21b..206e1a58ed 100644 --- a/package/firmware/ipq-wifi/Makefile +++ b/package/firmware/ipq-wifi/Makefile @@ -6,9 +6,9 @@ PKG_RELEASE:=1 PKG_SOURCE_PROTO:=git PKG_SOURCE_URL=$(PROJECT_GIT)/project/firmware/qca-wireless.git -PKG_SOURCE_DATE:=2024-02-19 -PKG_SOURCE_VERSION:=1cc59e1e09f68305bbf15e2de23d1c1829aee1eb -PKG_MIRROR_HASH:=383e7384d37cde2433b9bf6daee5d57ecd6f2c473f00901b491ae0c15d97fd53 +PKG_SOURCE_DATE:=2024-02-23 +PKG_SOURCE_VERSION:=9f9d9ba9cd77043744dcd5235497a15eea51c375 +PKG_MIRROR_HASH:=3a064a8810e6857580c4682f6b86a9dfcdb0d3aa361f4ec0c5480c54de4cc864 PKG_FLAGS:=nonshared @@ -37,6 +37,7 @@ ALLWIFIBOARDS:= \ edgecore_eap102 \ edimax_cax1800 \ linksys_mx4200 \ + linksys_mx5300 \ netgear_rax120v2 \ netgear_wax218 \ netgear_wax620 \ @@ -152,6 +153,7 @@ $(eval $(call generate-ipq-wifi-package,dynalink_dl-wrx36,Dynalink DL-WRX36)) $(eval $(call generate-ipq-wifi-package,edgecore_eap102,Edgecore EAP102)) $(eval $(call generate-ipq-wifi-package,edimax_cax1800,Edimax CAX1800)) $(eval $(call generate-ipq-wifi-package,linksys_mx4200,Linksys MX4200)) +$(eval $(call generate-ipq-wifi-package,linksys_mx5300,Linksys MX5300)) $(eval $(call generate-ipq-wifi-package,netgear_rax120v2,Netgear RAX120v2)) $(eval $(call generate-ipq-wifi-package,netgear_wax218,Netgear WAX218)) $(eval $(call generate-ipq-wifi-package,netgear_wax620,Netgear WAX620)) diff --git a/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8072-mx5300.dts b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8072-mx5300.dts new file mode 100644 index 0000000000..e44731a1be --- /dev/null +++ b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8072-mx5300.dts @@ -0,0 +1,544 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +/dts-v1/; + +#include "ipq8074.dtsi" +#include "ipq8074-hk-cpu.dtsi" +#include "ipq8074-ess.dtsi" +#include +#include +#include + +/ { + model = "Linksys MX5300"; + compatible = "linksys,mx5300", "qcom,ipq8074"; + + aliases { + serial0 = &blsp1_uart5; + /* + * Aliases as required by u-boot + * to patch MAC addresses + */ + ethernet0 = &dp1; + ethernet1 = &dp2; + ethernet2 = &dp3; + ethernet3 = &dp4; + ethernet4 = &dp5; + led-boot = &led_system_blue; + led-running = &led_system_blue; + led-failsafe = &led_system_red; + led-upgrade = &led_system_green; + }; + + chosen { + stdout-path = "serial0:115200n8"; + bootargs-append = " root=/dev/ubiblock0_0 rootfstype=squashfs ro"; + }; + + keys { + compatible = "gpio-keys"; + pinctrl-0 = <&button_pins>; + pinctrl-names = "default"; + + reset-button { + label = "reset"; + gpios = <&tlmm 67 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps-button { + label = "wps"; + gpios = <&tlmm 54 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; +}; + +&tlmm { + button_pins: button-state { + pins = "gpio54", "gpio67"; + function = "gpio"; + drive-strength = <8>; + bias-pull-up; + }; + + mdio_pins: mdio-state { + mdc-pins { + pins = "gpio68"; + function = "mdc"; + drive-strength = <8>; + bias-pull-up; + }; + + mdio-pins { + pins = "gpio69"; + function = "mdio"; + drive-strength = <8>; + bias-pull-up; + }; + }; + + /* + * QCA4024 is not currently supported, keep for documentation purposes + *spi_3_pins: spi-3-state { + * spi-pins { + * pins = "gpio50", "gpio52", "gpio53"; + * function = "blsp3_spi"; + * drive-strength = <8>; + * bias-disable; + * }; + * + * cs-pins { + * pins = "gpio22"; + * function = "blsp3_spi2"; + * drive-strength = <8>; + * bias-disable; + * }; + *}; + * + *quartz_pins: quartz-state { + * interrupt-pins { + * pins = "gpio48"; + * function = "gpio"; + * bias-disable; + * input; + * }; + * + * reset-pins { + * pins = "gpio21"; + * function = "gpio"; + * bias-disable; + * output-high; + * }; + *}; + */ +}; + +&blsp1_uart5 { + status = "okay"; +}; + +&prng { + status = "okay"; +}; + +&cryptobam { + status = "okay"; +}; + +&crypto { + status = "okay"; +}; + +&qpic_bam { + status = "okay"; +}; + +&qpic_nand { + status = "okay"; + + /* + * Bootloader will find the NAND DT node by the compatible and + * then "fixup" it by adding the partitions from the SMEM table + * using the legacy bindings thus making it impossible for us + * to change the partition table or utilize NVMEM for calibration. + * So add a dummy partitions node that bootloader will populate + * and set it as disabled so the kernel ignores it instead of + * printing warnings due to the broken way bootloader adds the + * partitions. + */ + partitions { + status = "disabled"; + }; + + nand@0 { + reg = <0>; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + nand-bus-width = <8>; + + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "0:sbl1"; + reg = <0x0 0x100000>; + read-only; + }; + + partition@100000 { + label = "0:mibib"; + reg = <0x100000 0x100000>; + read-only; + }; + + partition@200000 { + label = "0:bootconfig"; + reg = <0x200000 0x80000>; + read-only; + }; + + partition@280000 { + label = "0:bootconfig1"; + reg = <0x280000 0x80000>; + read-only; + }; + + partition@300000 { + label = "0:qsee"; + reg = <0x300000 0x300000>; + read-only; + }; + + partition@600000 { + label = "0:qsee_1"; + reg = <0x600000 0x300000>; + read-only; + }; + + partition@900000 { + label = "0:devcfg"; + reg = <0x900000 0x80000>; + read-only; + }; + + partition@980000 { + label = "0:devcfg_1"; + reg = <0x980000 0x80000>; + read-only; + }; + + partition@a00000 { + label = "0:apdp"; + reg = <0xa00000 0x80000>; + read-only; + }; + + partition@a80000 { + label = "0:apdp_1"; + reg = <0xa80000 0x80000>; + read-only; + }; + + partition@b00000 { + label = "0:rpm"; + reg = <0xb00000 0x80000>; + read-only; + }; + + partition@b80000 { + label = "0:rpm_1"; + reg = <0xb80000 0x80000>; + read-only; + }; + + partition@c00000 { + label = "0:cdt"; + reg = <0xc00000 0x80000>; + read-only; + }; + + partition@c80000 { + label = "0:cdt_1"; + reg = <0xc80000 0x80000>; + read-only; + }; + + partition@d00000 { + label = "0:appsblenv"; + reg = <0xd00000 0x80000>; + }; + + partition@d80000 { + label = "0:appsbl"; + reg = <0xd80000 0x100000>; + read-only; + }; + + partition@e80000 { + label = "0:appsbl_1"; + reg = <0xe80000 0x100000>; + read-only; + }; + + partition@f80000 { + label = "0:art"; + reg = <0xf80000 0x80000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + caldata_qca9984: caldata@33000 { + reg = <0x33000 0x2f20>; + }; + }; + }; + + partition@1000000 { + label = "u_env"; + reg = <0x1000000 0x40000>; + }; + + partition@1040000 { + label = "s_env"; + reg = <0x1040000 0x20000>; + }; + + partition@1060000 { + label = "devinfo"; + reg = <0x1060000 0x20000>; + read-only; + }; + + partition@1080000 { + label = "kernel"; + reg = <0x1080000 0x9600000>; + }; + + partition@1680000 { + label = "rootfs"; + reg = <0x1680000 0x9000000>; + }; + + partition@a680000 { + label = "alt_kernel"; + reg = <0xa680000 0x9600000>; + }; + + partition@ac80000 { + label = "alt_rootfs"; + reg = <0xac80000 0x9000000>; + }; + partition@13c80000 { + label = "sysdiag"; + reg = <0x13c80000 0x200000>; + read-only; + }; + partition@13e80000 { + label = "0:ethphyfw"; + reg = <0x13e80000 0x80000>; + read-only; + }; + partition@13f00000 { + label = "syscfg"; + reg = <0x13f00000 0xb800000>; + read-only; + }; + partition@1f700000 { + label = "0:wififw"; + reg = <0x1f700000 0x900000>; + read-only; + }; + }; + }; +}; + +&blsp1_i2c2 { + status = "okay"; + + led-controller@62 { + compatible = "nxp,pca9633"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x62>; + nxp,hw-blink; + + led_system_red: led@0 { + reg = <0>; + color = ; + function = LED_FUNCTION_STATUS; + }; + + led_system_green: led@1 { + reg = <1>; + color = ; + function = LED_FUNCTION_STATUS; + }; + + led_system_blue: led@2 { + reg = <2>; + color = ; + function = LED_FUNCTION_STATUS; + }; + }; + + rtc@68 { + compatible = "dallas,ds1307"; + reg = <0x68>; + }; +}; + +/* + * QCA4024 is not currently supported, keep for documentation purposes + *&blsp1_spi4 { + * status = "okay"; + * + * pinctrl-0 = <&spi_3_pins &quartz_pins>; + * pinctrl-names = "default"; + * + * iot@3 { + * compatible = "qca,qca4024"; + * reg = <0>; + * spi-max-frequency = <24000000>; + * }; + *}; + */ + +&mdio { + status = "okay"; + + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + reset-gpios = <&tlmm 37 GPIO_ACTIVE_LOW>; + + ethernet-phy-package@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "qcom,qca8075-package"; + reg = <0>; + + qca8075_0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + }; + + qca8075_1: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; + + qca8075_2: ethernet-phy@2 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <2>; + }; + + qca8075_3: ethernet-phy@3 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <3>; + }; + + qca8075_4: ethernet-phy@4 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <4>; + }; + }; +}; + +&switch { + status = "okay"; + + switch_lan_bmp = <(ESS_PORT1 | ESS_PORT2 | ESS_PORT3 | ESS_PORT4)>; /* lan port bitmap */ + switch_wan_bmp = ; /* wan port bitmap */ + switch_mac_mode = ; /* mac mode for uniphy instance0*/ + + qcom,port_phyinfo { + port@1 { + port_id = <1>; + phy_address = <0>; + }; + port@2 { + port_id = <2>; + phy_address = <1>; + }; + port@3 { + port_id = <3>; + phy_address = <2>; + }; + port@4 { + port_id = <4>; + phy_address = <3>; + }; + port@5 { + port_id = <5>; + phy_address = <4>; + }; + }; +}; + +&edma { + status = "okay"; +}; + +&dp1 { + status = "okay"; + phy-handle = <&qca8075_0>; + label = "lan1"; +}; + +&dp2 { + status = "okay"; + phy-handle = <&qca8075_1>; + label = "lan2"; +}; + +&dp3 { + status = "okay"; + phy-handle = <&qca8075_2>; + label = "lan3"; +}; + +&dp4 { + status = "okay"; + phy-handle = <&qca8075_3>; + label = "lan4"; +}; + +&dp5 { + status = "okay"; + phy-handle = <&qca8075_4>; + label = "wan"; +}; + +&ssphy_0 { + status = "okay"; +}; + +&qusb_phy_0 { + status = "okay"; +}; + +&usb_0 { + status = "okay"; +}; + +&pcie_qmp1 { + status = "okay"; +}; + +&pcie1 { + status = "okay"; + + perst-gpio = <&tlmm 58 GPIO_ACTIVE_LOW>; + + bridge@0,0 { + reg = <0x00000000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + ranges; + + wifi0: wifi@1,0 { + status = "okay"; + + compatible = "qcom,ath10k"; + reg = <0x00010000 0 0 0 0>; + + qcom,ath10k-calibration-variant = "Linksys-MX5300"; + nvmem-cell-names = "pre-calibration"; + nvmem-cells = <&caldata_qca9984>; + }; + }; +}; + +&wifi { + status = "okay"; + + qcom,ath11k-calibration-variant = "Linksys-MX5300"; +}; diff --git a/target/linux/qualcommax/image/ipq807x.mk b/target/linux/qualcommax/image/ipq807x.mk index 916c8b9f75..74fe15a997 100644 --- a/target/linux/qualcommax/image/ipq807x.mk +++ b/target/linux/qualcommax/image/ipq807x.mk @@ -126,6 +126,23 @@ define Device/linksys_mx4200v2 endef TARGET_DEVICES += linksys_mx4200v2 +define Device/linksys_mx5300 + $(call Device/FitImage) + DEVICE_VENDOR := Linksys + DEVICE_MODEL := MX5300 + BLOCKSIZE := 128k + PAGESIZE := 2048 + KERNEL_SIZE := 6144k + IMAGE_SIZE := 147456k + NAND_SIZE := 512m + SOC := ipq8072 + IMAGES += factory.bin + IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=MX5300 + DEVICE_PACKAGES := kmod-leds-pca963x kmod-rtc-ds1307 \ + ipq-wifi-linksys_mx5300 kmod-ath10k-ct ath10k-firmware-qca9984-ct +endef +TARGET_DEVICES += linksys_mx5300 + define Device/netgear_rax120v2 $(call Device/FitImage) $(call Device/UbiFit) diff --git a/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network b/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network index 1da97a8fa3..fb3fec6fc9 100644 --- a/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network +++ b/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network @@ -14,6 +14,7 @@ ipq807x_setup_interfaces() arcadyan,aw1000|\ buffalo,wxr-5950ax12|\ dynalink,dl-wrx36|\ + linksys,mx5300|\ xiaomi,ax9000) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan" ;; diff --git a/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata b/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata index 95011ee568..88ba972407 100644 --- a/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata +++ b/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata @@ -18,6 +18,7 @@ case "$FIRMWARE" in edimax,cax1800|\ linksys,mx4200v1|\ linksys,mx4200v2|\ + linksys,mx5300|\ netgear,rax120v2|\ netgear,wax218|\ netgear,wax620|\ diff --git a/target/linux/qualcommax/ipq807x/base-files/etc/init.d/bootcount b/target/linux/qualcommax/ipq807x/base-files/etc/init.d/bootcount index f5f6c909e9..3e81caf63f 100755 --- a/target/linux/qualcommax/ipq807x/base-files/etc/init.d/bootcount +++ b/target/linux/qualcommax/ipq807x/base-files/etc/init.d/bootcount @@ -11,7 +11,8 @@ boot() { fw_setenv changed ;; linksys,mx4200v1|\ - linksys,mx4200v2) + linksys,mx4200v2|\ + linksys,mx5300) mtd resetbc s_env || true ;; esac diff --git a/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh b/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh index b03a063af3..bffca41e02 100644 --- a/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh +++ b/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh @@ -75,7 +75,8 @@ platform_do_upgrade() { nand_do_upgrade "$1" ;; linksys,mx4200v1|\ - linksys,mx4200v2) + linksys,mx4200v2|\ + linksys,mx5300) boot_part="$(fw_printenv -n boot_part)" if [ "$boot_part" -eq "1" ]; then fw_setenv boot_part 2