From: Hauke Mehrtens Date: Sat, 20 Jun 2009 18:44:24 +0000 (+0000) Subject: Add ADM6996 switch driver X-Git-Tag: reboot~23158 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=6e42b25c88119d50df668e12f0e62579c622d0ca;p=openwrt%2Fopenwrt.git Add ADM6996 switch driver This fixes #5314 Thanks to Michael Richter SVN-Revision: 16523 --- diff --git a/target/linux/amazon/config-2.6.21 b/target/linux/amazon/config-2.6.21 index da338fda3e..c406070b15 100644 --- a/target/linux/amazon/config-2.6.21 +++ b/target/linux/amazon/config-2.6.21 @@ -1,6 +1,7 @@ CONFIG_32BIT=y # CONFIG_64BIT is not set # CONFIG_64BIT_PHYS_ADDR is not set +CONFIG_ADM6996_SUPPORT=y CONFIG_AMAZON=y CONFIG_AMAZON_ASC_UART=y CONFIG_AMAZON_MTD=y diff --git a/target/linux/amazon/files/arch/mips/amazon/Kconfig b/target/linux/amazon/files/arch/mips/amazon/Kconfig index 179e35efd2..63055fc2aa 100644 --- a/target/linux/amazon/files/arch/mips/amazon/Kconfig +++ b/target/linux/amazon/files/arch/mips/amazon/Kconfig @@ -26,6 +26,10 @@ config AMAZON_MTD bool "Amazon MTD map" default y +config ADM6996_SUPPORT + bool "Amazon ADM6996 Switch driver" + default y + choice prompt "Flash Size" depends on AMAZON_MTD diff --git a/target/linux/amazon/files/drivers/char/admmod.c b/target/linux/amazon/files/drivers/char/admmod.c deleted file mode 100644 index 0229f53f55..0000000000 --- a/target/linux/amazon/files/drivers/char/admmod.c +++ /dev/null @@ -1,1486 +0,0 @@ -/****************************************************************************** - Copyright (c) 2004, Infineon Technologies. All rights reserved. - - No Warranty - Because the program is licensed free of charge, there is no warranty for - the program, to the extent permitted by applicable law. Except when - otherwise stated in writing the copyright holders and/or other parties - provide the program "as is" without warranty of any kind, either - expressed or implied, including, but not limited to, the implied - warranties of merchantability and fitness for a particular purpose. The - entire risk as to the quality and performance of the program is with - you. should the program prove defective, you assume the cost of all - necessary servicing, repair or correction. - - In no event unless required by applicable law or agreed to in writing - will any copyright holder, or any other party who may modify and/or - redistribute the program as permitted above, be liable to you for - damages, including any general, special, incidental or consequential - damages arising out of the use or inability to use the program - (including but not limited to loss of data or data being rendered - inaccurate or losses sustained by you or third parties or a failure of - the program to operate with any other programs), even if such holder or - other party has been advised of the possibility of such damages. - ****************************************************************************** - Module : admmod.c - Date : 2004-09-01 - Description : JoeLin - Remarks: - - Revision: - MarsLin, add to support VLAN - - *****************************************************************************/ -//000001.joelin 2005/06/02 add"ADM6996_MDC_MDIO_MODE" define, -// if define ADM6996_MDC_MDIO_MODE==> ADM6996LC and ADM6996I will be in MDIO/MDC(SMI)(16 bit) mode, -// amazon should contrl ADM6996 by MDC/MDIO pin -// if undef ADM6996_MDC_MDIO_MODE==> ADM6996 will be in EEProm(32 bit) mode, -// amazon should contrl ADM6996 by GPIO15,16,17,18 pin -/* 507281:linmars 2005/07/28 support MDIO/EEPROM config mode */ -/* 509201:linmars remove driver testing codes */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -//#include - - -unsigned int ifx_sw_conf[ADM_SW_MAX_PORT_NUM+1] = \ - {ADM_SW_PORT0_CONF, ADM_SW_PORT1_CONF, ADM_SW_PORT2_CONF, \ - ADM_SW_PORT3_CONF, ADM_SW_PORT4_CONF, ADM_SW_PORT5_CONF}; -unsigned int ifx_sw_bits[8] = \ - {0x1, 0x3, 0x7, 0xf, 0x1f, 0x3f, 0x7f, 0xff}; -unsigned int ifx_sw_vlan_port[6] = {0, 2, 4, 6, 7, 8}; -//050613:fchang -/* 507281:linmars start */ -#ifdef CONFIG_SWITCH_ADM6996_MDIO -#define ADM6996_MDC_MDIO_MODE 1 //000001.joelin -#else -#undef ADM6996_MDC_MDIO_MODE -#endif -/* 507281:linmars end */ -#define adm6996i 0 -#define adm6996lc 1 -#define adm6996l 2 -unsigned int adm6996_mode=adm6996i; -/* - initialize GPIO pins. - output mode, low -*/ -void ifx_gpio_init(void) -{ - //GPIO16,17,18 direction:output - //GPIO16,17,18 output 0 - - AMAZON_SW_REG(AMAZON_GPIO_P1_DIR) |= (GPIO_MDIO|GPIO_MDCS|GPIO_MDC); - AMAZON_SW_REG(AMAZON_GPIO_P1_OUT) =AMAZON_SW_REG(AMAZON_GPIO_P1_IN)& ~(GPIO_MDIO|GPIO_MDCS|GPIO_MDC); - -} - -/* read one bit from mdio port */ -int ifx_sw_mdio_readbit(void) -{ - //int val; - - //val = (AMAZON_SW_REG(GPIO_conf0_REG) & GPIO0_INPUT_MASK) >> 8; - //return val; - //GPIO16 - return AMAZON_SW_REG(AMAZON_GPIO_P1_IN)&1; -} - -/* - MDIO mode selection - 1 -> output - 0 -> input - - switch input/output mode of GPIO 0 -*/ -void ifx_mdio_mode(int mode) -{ -// AMAZON_SW_REG(GPIO_conf0_REG) = mode ? GPIO_ENABLEBITS : -// ((GPIO_ENABLEBITS | MDIO_INPUT) & ~MDIO_OUTPUT_EN); - mode?(AMAZON_SW_REG(AMAZON_GPIO_P1_DIR)|=GPIO_MDIO): - (AMAZON_SW_REG(AMAZON_GPIO_P1_DIR)&=~GPIO_MDIO); - /*int r=AMAZON_SW_REG(AMAZON_GPIO_P1_DIR); - mode?(r|=GPIO_MDIO):(r&=~GPIO_MDIO); - AMAZON_SW_REG(AMAZON_GPIO_P1_DIR)=r;*/ -} - -void ifx_mdc_hi(void) -{ - //GPIO_SET_HI(GPIO_MDC); - //AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)|=GPIO_MDC; - /*int r=AMAZON_SW_REG(AMAZON_GPIO_P1_OUT); - r|=GPIO_MDC; - AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=r;*/ - - AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=AMAZON_SW_REG(AMAZON_GPIO_P1_IN)|GPIO_MDC; -} - -void ifx_mdio_hi(void) -{ - //GPIO_SET_HI(GPIO_MDIO); - //AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)|=GPIO_MDIO; - /*int r=AMAZON_SW_REG(AMAZON_GPIO_P1_OUT); - r|=GPIO_MDIO; - AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=r;*/ - - AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=AMAZON_SW_REG(AMAZON_GPIO_P1_IN)|GPIO_MDIO; -} - -void ifx_mdcs_hi(void) -{ - //GPIO_SET_HI(GPIO_MDCS); - //AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)|=GPIO_MDCS; - /*int r=AMAZON_SW_REG(AMAZON_GPIO_P1_OUT); - r|=GPIO_MDCS; - AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=r;*/ - - AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=AMAZON_SW_REG(AMAZON_GPIO_P1_IN)|GPIO_MDCS; -} - -void ifx_mdc_lo(void) -{ - //GPIO_SET_LOW(GPIO_MDC); - //AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)&=~GPIO_MDC; - /*int r=AMAZON_SW_REG(AMAZON_GPIO_P1_OUT); - r&=~GPIO_MDC; - AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=r;*/ - - AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=AMAZON_SW_REG(AMAZON_GPIO_P1_IN)&(~GPIO_MDC); -} - -void ifx_mdio_lo(void) -{ - //GPIO_SET_LOW(GPIO_MDIO); - //AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)&=~GPIO_MDIO; - /*int r=AMAZON_SW_REG(AMAZON_GPIO_P1_OUT); - r&=~GPIO_MDIO; - AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=r;*/ - - AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=AMAZON_SW_REG(AMAZON_GPIO_P1_IN)&(~GPIO_MDIO); -} - -void ifx_mdcs_lo(void) -{ - //GPIO_SET_LOW(GPIO_MDCS); - //AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)&=~GPIO_MDCS; - /*int r=AMAZON_SW_REG(AMAZON_GPIO_P1_OUT); - r&=~GPIO_MDCS; - AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=r;*/ - - AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=AMAZON_SW_REG(AMAZON_GPIO_P1_IN)&(~GPIO_MDCS); -} - -/* - mdc pulse - 0 -> 1 -> 0 -*/ -static void ifx_sw_mdc_pulse(void) -{ - ifx_mdc_lo(); - udelay(ADM_SW_MDC_DOWN_DELAY); - ifx_mdc_hi(); - udelay(ADM_SW_MDC_UP_DELAY); - ifx_mdc_lo(); -} - -/* - mdc toggle - 1 -> 0 -*/ -static void ifx_sw_mdc_toggle(void) -{ - ifx_mdc_hi(); - udelay(ADM_SW_MDC_UP_DELAY); - ifx_mdc_lo(); - udelay(ADM_SW_MDC_DOWN_DELAY); -} - -/* - enable eeprom write - For ATC 93C66 type EEPROM; accessing ADM6996 internal EEPROM type registers -*/ -static void ifx_sw_eeprom_write_enable(void) -{ - unsigned int op; - - ifx_mdcs_lo(); - ifx_mdc_lo(); - ifx_mdio_hi(); - udelay(ADM_SW_CS_DELAY); - /* enable chip select */ - ifx_mdcs_hi(); - udelay(ADM_SW_CS_DELAY); - /* start bit */ - ifx_mdio_hi(); - ifx_sw_mdc_pulse(); - - /* eeprom write enable */ - op = ADM_SW_BIT_MASK_4; - while (op) - { - if (op & ADM_SW_EEPROM_WRITE_ENABLE) - ifx_mdio_hi(); - else - ifx_mdio_lo(); - - ifx_sw_mdc_pulse(); - op >>= 1; - } - - op = ADM_SW_BIT_MASK_1 << (EEPROM_TYPE - 3); - while (op) - { - ifx_mdio_lo(); - ifx_sw_mdc_pulse(); - op >>= 1; - } - /* disable chip select */ - ifx_mdcs_lo(); - udelay(ADM_SW_CS_DELAY); - ifx_sw_mdc_pulse(); -} - -/* - disable eeprom write -*/ -static void ifx_sw_eeprom_write_disable(void) -{ - unsigned int op; - - ifx_mdcs_lo(); - ifx_mdc_lo(); - ifx_mdio_hi(); - udelay(ADM_SW_CS_DELAY); - /* enable chip select */ - ifx_mdcs_hi(); - udelay(ADM_SW_CS_DELAY); - - /* start bit */ - ifx_mdio_hi(); - ifx_sw_mdc_pulse(); - /* eeprom write disable */ - op = ADM_SW_BIT_MASK_4; - while (op) - { - if (op & ADM_SW_EEPROM_WRITE_DISABLE) - ifx_mdio_hi(); - else - ifx_mdio_lo(); - - ifx_sw_mdc_pulse(); - op >>= 1; - } - - op = ADM_SW_BIT_MASK_1 << (EEPROM_TYPE - 3); - while (op) - { - ifx_mdio_lo(); - - ifx_sw_mdc_pulse(); - op >>= 1; - } - /* disable chip select */ - ifx_mdcs_lo(); - udelay(ADM_SW_CS_DELAY); - ifx_sw_mdc_pulse(); -} - -/* - read registers from ADM6996 - serial registers start at 0x200 (addr bit 9 = 1b) - EEPROM registers -> 16bits; Serial registers -> 32bits -*/ -#ifdef ADM6996_MDC_MDIO_MODE //smi mode//000001.joelin -static int ifx_sw_read_adm6996i_smi(unsigned int addr, unsigned int *dat) -{ - addr=(addr<<16)&0x3ff0000; - AMAZON_SW_REG(AMAZON_SW_MDIO_ACC) =(0xC0000000|addr); - while ((AMAZON_SW_REG(AMAZON_SW_MDIO_ACC))&0x80000000){}; - *dat=((AMAZON_SW_REG(AMAZON_SW_MDIO_ACC))&0x0FFFF); - return 0; -} -#endif - -static int ifx_sw_read_adm6996i(unsigned int addr, unsigned int *dat) -{ - unsigned int op; - - ifx_gpio_init(); - - ifx_mdcs_hi(); - udelay(ADM_SW_CS_DELAY); - - ifx_mdcs_lo(); - ifx_mdc_lo(); - ifx_mdio_lo(); - - udelay(ADM_SW_CS_DELAY); - - /* preamble, 32 bit 1 */ - ifx_mdio_hi(); - op = ADM_SW_BIT_MASK_32; - while (op) - { - ifx_sw_mdc_pulse(); - op >>= 1; - } - - /* command start (01b) */ - op = ADM_SW_BIT_MASK_2; - while (op) - { - if (op & ADM_SW_SMI_START) - ifx_mdio_hi(); - else - ifx_mdio_lo(); - - ifx_sw_mdc_pulse(); - op >>= 1; - } - - /* read command (10b) */ - op = ADM_SW_BIT_MASK_2; - while (op) - { - if (op & ADM_SW_SMI_READ) - ifx_mdio_hi(); - else - ifx_mdio_lo(); - - ifx_sw_mdc_pulse(); - op >>= 1; - } - - /* send address A9 ~ A0 */ - op = ADM_SW_BIT_MASK_10; - while (op) - { - if (op & addr) - ifx_mdio_hi(); - else - ifx_mdio_lo(); - - ifx_sw_mdc_pulse(); - op >>= 1; - } - - /* turnaround bits */ - op = ADM_SW_BIT_MASK_2; - ifx_mdio_hi(); - while (op) - { - ifx_sw_mdc_pulse(); - op >>= 1; - } - - udelay(ADM_SW_MDC_DOWN_DELAY); - - /* set MDIO pin to input mode */ - ifx_mdio_mode(ADM_SW_MDIO_INPUT); - - /* start read data */ - *dat = 0; -//adm6996i op = ADM_SW_BIT_MASK_32; - op = ADM_SW_BIT_MASK_16;//adm6996i - while (op) - { - *dat <<= 1; - if (ifx_sw_mdio_readbit()) *dat |= 1; - ifx_sw_mdc_toggle(); - - op >>= 1; - } - - /* set MDIO to output mode */ - ifx_mdio_mode(ADM_SW_MDIO_OUTPUT); - - /* dummy clock */ - op = ADM_SW_BIT_MASK_4; - ifx_mdio_lo(); - while(op) - { - ifx_sw_mdc_pulse(); - op >>= 1; - } - - ifx_mdc_lo(); - ifx_mdio_lo(); - ifx_mdcs_hi(); - - /* EEPROM registers */ -//adm6996i if (!(addr & 0x200)) -//adm6996i { -//adm6996i if (addr % 2) -//adm6996i *dat >>= 16; -//adm6996i else -//adm6996i *dat &= 0xffff; -//adm6996i } - - return 0; -} -//adm6996 -static int ifx_sw_read_adm6996l(unsigned int addr, unsigned int *dat) -{ - unsigned int op; - - ifx_gpio_init(); - - ifx_mdcs_hi(); - udelay(ADM_SW_CS_DELAY); - - ifx_mdcs_lo(); - ifx_mdc_lo(); - ifx_mdio_lo(); - - udelay(ADM_SW_CS_DELAY); - - /* preamble, 32 bit 1 */ - ifx_mdio_hi(); - op = ADM_SW_BIT_MASK_32; - while (op) - { - ifx_sw_mdc_pulse(); - op >>= 1; - } - - /* command start (01b) */ - op = ADM_SW_BIT_MASK_2; - while (op) - { - if (op & ADM_SW_SMI_START) - ifx_mdio_hi(); - else - ifx_mdio_lo(); - - ifx_sw_mdc_pulse(); - op >>= 1; - } - - /* read command (10b) */ - op = ADM_SW_BIT_MASK_2; - while (op) - { - if (op & ADM_SW_SMI_READ) - ifx_mdio_hi(); - else - ifx_mdio_lo(); - - ifx_sw_mdc_pulse(); - op >>= 1; - } - - /* send address A9 ~ A0 */ - op = ADM_SW_BIT_MASK_10; - while (op) - { - if (op & addr) - ifx_mdio_hi(); - else - ifx_mdio_lo(); - - ifx_sw_mdc_pulse(); - op >>= 1; - } - - /* turnaround bits */ - op = ADM_SW_BIT_MASK_2; - ifx_mdio_hi(); - while (op) - { - ifx_sw_mdc_pulse(); - op >>= 1; - } - - udelay(ADM_SW_MDC_DOWN_DELAY); - - /* set MDIO pin to input mode */ - ifx_mdio_mode(ADM_SW_MDIO_INPUT); - - /* start read data */ - *dat = 0; - op = ADM_SW_BIT_MASK_32; - while (op) - { - *dat <<= 1; - if (ifx_sw_mdio_readbit()) *dat |= 1; - ifx_sw_mdc_toggle(); - - op >>= 1; - } - - /* set MDIO to output mode */ - ifx_mdio_mode(ADM_SW_MDIO_OUTPUT); - - /* dummy clock */ - op = ADM_SW_BIT_MASK_4; - ifx_mdio_lo(); - while(op) - { - ifx_sw_mdc_pulse(); - op >>= 1; - } - - ifx_mdc_lo(); - ifx_mdio_lo(); - ifx_mdcs_hi(); - - /* EEPROM registers */ - if (!(addr & 0x200)) - { - if (addr % 2) - *dat >>= 16; - else - *dat &= 0xffff; - } - - return 0; -} - -static int ifx_sw_read(unsigned int addr, unsigned int *dat) -{ -#ifdef ADM6996_MDC_MDIO_MODE //smi mode ////000001.joelin - ifx_sw_read_adm6996i_smi(addr,dat); -#else - if (adm6996_mode==adm6996i) ifx_sw_read_adm6996i(addr,dat); - else ifx_sw_read_adm6996l(addr,dat); -#endif - return 0; - -} - -/* - write register to ADM6996 eeprom registers -*/ -//for adm6996i -start -#ifdef ADM6996_MDC_MDIO_MODE //smi mode //000001.joelin -static int ifx_sw_write_adm6996i_smi(unsigned int addr, unsigned int dat) -{ - - AMAZON_SW_REG(AMAZON_SW_MDIO_ACC) = ((addr<<16)&0x3ff0000)|dat|0x80000000; - while ((AMAZON_SW_REG(AMAZON_SW_MDIO_ACC))&0x80000000){}; - - return 0; - -} -#endif //ADM6996_MDC_MDIO_MODE //000001.joelin - -static int ifx_sw_write_adm6996i(unsigned int addr, unsigned int dat) -{ - unsigned int op; - - ifx_gpio_init(); - - ifx_mdcs_hi(); - udelay(ADM_SW_CS_DELAY); - - ifx_mdcs_lo(); - ifx_mdc_lo(); - ifx_mdio_lo(); - - udelay(ADM_SW_CS_DELAY); - - /* preamble, 32 bit 1 */ - ifx_mdio_hi(); - op = ADM_SW_BIT_MASK_32; - while (op) - { - ifx_sw_mdc_pulse(); - op >>= 1; - } - - /* command start (01b) */ - op = ADM_SW_BIT_MASK_2; - while (op) - { - if (op & ADM_SW_SMI_START) - ifx_mdio_hi(); - else - ifx_mdio_lo(); - - ifx_sw_mdc_pulse(); - op >>= 1; - } - - /* write command (01b) */ - op = ADM_SW_BIT_MASK_2; - while (op) - { - if (op & ADM_SW_SMI_WRITE) - ifx_mdio_hi(); - else - ifx_mdio_lo(); - - ifx_sw_mdc_pulse(); - op >>= 1; - } - - /* send address A9 ~ A0 */ - op = ADM_SW_BIT_MASK_10; - while (op) - { - if (op & addr) - ifx_mdio_hi(); - else - ifx_mdio_lo(); - - ifx_sw_mdc_pulse(); - op >>= 1; - } - - /* turnaround bits */ - op = ADM_SW_BIT_MASK_2; - ifx_mdio_hi(); - while (op) - { - ifx_sw_mdc_pulse(); - op >>= 1; - } - - udelay(ADM_SW_MDC_DOWN_DELAY); - - /* set MDIO pin to output mode */ - ifx_mdio_mode(ADM_SW_MDIO_OUTPUT); - - - /* start write data */ - op = ADM_SW_BIT_MASK_16; - while (op) - { - if (op & dat) - ifx_mdio_hi(); - else - ifx_mdio_lo(); - - ifx_sw_mdc_toggle(); - op >>= 1; - } - - // /* set MDIO to output mode */ - // ifx_mdio_mode(ADM_SW_MDIO_OUTPUT); - - /* dummy clock */ - op = ADM_SW_BIT_MASK_4; - ifx_mdio_lo(); - while(op) - { - ifx_sw_mdc_pulse(); - op >>= 1; - } - - ifx_mdc_lo(); - ifx_mdio_lo(); - ifx_mdcs_hi(); - - /* EEPROM registers */ -//adm6996i if (!(addr & 0x200)) -//adm6996i { -//adm6996i if (addr % 2) -//adm6996i *dat >>= 16; -//adm6996i else -//adm6996i *dat &= 0xffff; -//adm6996i } - - return 0; -} -//for adm6996i-end -static int ifx_sw_write_adm6996l(unsigned int addr, unsigned int dat) -{ - unsigned int op; - - ifx_gpio_init(); - - /* enable write */ - ifx_sw_eeprom_write_enable(); - - /* chip select */ - ifx_mdcs_hi(); - udelay(ADM_SW_CS_DELAY); - - /* issue write command */ - /* start bit */ - ifx_mdio_hi(); - ifx_sw_mdc_pulse(); - - /* EEPROM write command */ - op = ADM_SW_BIT_MASK_2; - while (op) - { - if (op & ADM_SW_EEPROM_WRITE) - ifx_mdio_hi(); - else - ifx_mdio_lo(); - - ifx_sw_mdc_pulse(); - op >>= 1; - } - - /* send address A7 ~ A0 */ - op = ADM_SW_BIT_MASK_1 << (EEPROM_TYPE - 1); - - while (op) - { - if (op & addr) - ifx_mdio_hi(); - else - ifx_mdio_lo(); - - ifx_sw_mdc_toggle(); - op >>= 1; - } - - /* start write data */ - op = ADM_SW_BIT_MASK_16; - while (op) - { - if (op & dat) - ifx_mdio_hi(); - else - ifx_mdio_lo(); - - ifx_sw_mdc_toggle(); - op >>= 1; - } - - /* disable cs & wait 1 clock */ - ifx_mdcs_lo(); - udelay(ADM_SW_CS_DELAY); - ifx_sw_mdc_toggle(); - - ifx_sw_eeprom_write_disable(); - - return 0; -} - -static int ifx_sw_write(unsigned int addr, unsigned int dat) -{ -#ifdef ADM6996_MDC_MDIO_MODE //smi mode ////000001.joelin - ifx_sw_write_adm6996i_smi(addr,dat); -#else //000001.joelin - if (adm6996_mode==adm6996i) ifx_sw_write_adm6996i(addr,dat); - else ifx_sw_write_adm6996l(addr,dat); -#endif //000001.joelin - return 0; -} - -/* - do switch PHY reset -*/ -int ifx_sw_reset(void) -{ - /* reset PHY */ - ifx_sw_write(ADM_SW_PHY_RESET, 0); - - return 0; -} - -/* 509201:linmars start */ -#if 0 -/* - check port status -*/ -int ifx_check_port_status(int port) -{ - unsigned int val; - - if ((port < 0) || (port > ADM_SW_MAX_PORT_NUM)) - { - ifx_printf(("error on port number (%d)!!\n", port)); - return -1; - } - - ifx_sw_read(ifx_sw_conf[port], &val); - if (ifx_sw_conf[port]%2) val >>= 16; - /* only 16bits are effective */ - val &= 0xFFFF; - - ifx_printf(("Port %d status (%.8x): \n", port, val)); - - if (val & ADM_SW_PORT_FLOWCTL) - ifx_printf(("\t802.3x flow control supported!\n")); - else - ifx_printf(("\t802.3x flow control not supported!\n")); - - if (val & ADM_SW_PORT_AN) - ifx_printf(("\tAuto negotiation ON!\n")); - else - ifx_printf(("\tAuto negotiation OFF!\n")); - - if (val & ADM_SW_PORT_100M) - ifx_printf(("\tLink at 100M!\n")); - else - ifx_printf(("\tLink at 10M!\n")); - - if (val & ADM_SW_PORT_FULL) - ifx_printf(("\tFull duplex!\n")); - else - ifx_printf(("\tHalf duplex!\n")); - - if (val & ADM_SW_PORT_DISABLE) - ifx_printf(("\tPort disabled!\n")); - else - ifx_printf(("\tPort enabled!\n")); - - if (val & ADM_SW_PORT_TOS) - ifx_printf(("\tTOS enabled!\n")); - else - ifx_printf(("\tTOS disabled!\n")); - - if (val & ADM_SW_PORT_PPRI) - ifx_printf(("\tPort priority first!\n")); - else - ifx_printf(("\tVLAN or TOS priority first!\n")); - - if (val & ADM_SW_PORT_MDIX) - ifx_printf(("\tAuto MDIX!\n")); - else - ifx_printf(("\tNo auto MDIX\n")); - - ifx_printf(("\tPVID: %d\n", \ - ((val >> ADM_SW_PORT_PVID_SHIFT)&ifx_sw_bits[ADM_SW_PORT_PVID_BITS]))); - - return 0; -} -/* - initialize a VLAN - clear all VLAN bits -*/ -int ifx_sw_vlan_init(int vlanid) -{ - ifx_sw_write(ADM_SW_VLAN0_CONF + vlanid, 0); - - return 0; -} - -/* - add a port to certain vlan -*/ -int ifx_sw_vlan_add(int port, int vlanid) -{ - int reg = 0; - - if ((port < 0) || (port > ADM_SW_MAX_PORT_NUM) || (vlanid < 0) || - (vlanid > ADM_SW_MAX_VLAN_NUM)) - { - ifx_printf(("Port number or VLAN number ERROR!!\n")); - return -1; - } - ifx_sw_read(ADM_SW_VLAN0_CONF + vlanid, ®); - reg |= (1 << ifx_sw_vlan_port[port]); - ifx_sw_write(ADM_SW_VLAN0_CONF + vlanid, reg); - - return 0; -} - -/* - delete a given port from certain vlan -*/ -int ifx_sw_vlan_del(int port, int vlanid) -{ - unsigned int reg = 0; - - if ((port < 0) || (port > ADM_SW_MAX_PORT_NUM) || (vlanid < 0) || (vlanid > ADM_SW_MAX_VLAN_NUM)) - { - ifx_printf(("Port number or VLAN number ERROR!!\n")); - return -1; - } - ifx_sw_read(ADM_SW_VLAN0_CONF + vlanid, ®); - reg &= ~(1 << ifx_sw_vlan_port[port]); - ifx_sw_write(ADM_SW_VLAN0_CONF + vlanid, reg); - - return 0; -} - -/* - default VLAN setting - - port 0~3 as untag port and PVID = 1 - VLAN1: port 0~3 and port 5 (MII) -*/ -static int ifx_sw_init(void) -{ - ifx_printf(("Setting default ADM6996 registers... \n")); - - /* MAC clone, 802.1q based VLAN */ - ifx_sw_write(ADM_SW_VLAN_MODE, 0xff30); - /* auto MDIX, PVID=1, untag */ - ifx_sw_write(ADM_SW_PORT0_CONF, 0x840f); - ifx_sw_write(ADM_SW_PORT1_CONF, 0x840f); - ifx_sw_write(ADM_SW_PORT2_CONF, 0x840f); - ifx_sw_write(ADM_SW_PORT3_CONF, 0x840f); - /* auto MDIX, PVID=2, untag */ - ifx_sw_write(ADM_SW_PORT5_CONF, 0x880f); - /* port 0~3 & 5 as VLAN1 */ - ifx_sw_write(ADM_SW_VLAN0_CONF+1, 0x0155); - - return 0; -} -#endif -/* 509201:linmars end */ - -int adm_open(struct inode *node, struct file *filp) -{ - MOD_INC_USE_COUNT; - return 0; -} - -ssize_t adm_read(struct file *filep, char *buf, size_t count, loff_t *ppos) -{ - return count; -} - -ssize_t adm_write(struct file *filep, const char *buf, size_t count, loff_t *ppos) -{ - return count; -} - -/* close */ -int adm_release(struct inode *inode, struct file *filp) -{ - MOD_DEC_USE_COUNT; - return 0; -} - -/* IOCTL function */ -int adm_ioctl(struct inode *inode, struct file *filp, unsigned int cmd, unsigned long args) -{ - PREGRW uREGRW; - unsigned int rtval; - unsigned int val; //6996i - unsigned int control[6] ; //6996i - unsigned int status[6] ; //6996i - - PMACENTRY mMACENTRY;//adm6996i - PPROTOCOLFILTER uPROTOCOLFILTER ;///adm6996i - - if (_IOC_TYPE(cmd) != ADM_MAGIC) - { - printk("adm_ioctl: IOC_TYPE(%x) != ADM_MAGIC(%x)! \n", _IOC_TYPE(cmd), ADM_MAGIC); - return (-EINVAL); - } - - if(_IOC_NR(cmd) >= KEY_IOCTL_MAX_KEY) - { - printk(KERN_WARNING "adm_ioctl: IOC_NR(%x) invalid! \n", _IOC_NR(cmd)); - return (-EINVAL); - } - - switch (cmd) - { - case ADM_IOCTL_REGRW: - { - uREGRW = (PREGRW)kmalloc(sizeof(REGRW), GFP_KERNEL); - rtval = copy_from_user(uREGRW, (PREGRW)args, sizeof(REGRW)); - if (rtval != 0) - { - printk("ADM_IOCTL_REGRW: copy from user FAILED!! \n"); - return (-EFAULT); - } - - switch(uREGRW->mode) - { - case REG_READ: - uREGRW->value = 0x12345678;//inl(uREGRW->addr); - copy_to_user((PREGRW)args, uREGRW, sizeof(REGRW)); - break; - case REG_WRITE: - //outl(uREGRW->value, uREGRW->addr); - break; - - default: - printk("No such Register Read/Write function!! \n"); - return (-EFAULT); - } - kfree(uREGRW); - break; - } - - case ADM_SW_IOCTL_REGRW: - { - unsigned int val = 0xff; - - uREGRW = (PREGRW)kmalloc(sizeof(REGRW), GFP_KERNEL); - rtval = copy_from_user(uREGRW, (PREGRW)args, sizeof(REGRW)); - if (rtval != 0) - { - printk("ADM_IOCTL_REGRW: copy from user FAILED!! \n"); - return (-EFAULT); - } - - switch(uREGRW->mode) - { - case REG_READ: - ifx_sw_read(uREGRW->addr, &val); - uREGRW->value = val; - copy_to_user((PREGRW)args, uREGRW, sizeof(REGRW)); - break; - - case REG_WRITE: - ifx_sw_write(uREGRW->addr, uREGRW->value); - break; - default: - printk("No such Register Read/Write function!! \n"); - return (-EFAULT); - } - kfree(uREGRW); - break; - } -/* 509201:linmars start */ -#if 0 - case ADM_SW_IOCTL_PORTSTS: - for (rtval = 0; rtval < ADM_SW_MAX_PORT_NUM+1; rtval++) - ifx_check_port_status(rtval); - break; - case ADM_SW_IOCTL_INIT: - ifx_sw_init(); - break; -#endif -/* 509201:linmars end */ -//adm6996i - case ADM_SW_IOCTL_MACENTRY_ADD: - case ADM_SW_IOCTL_MACENTRY_DEL: - case ADM_SW_IOCTL_MACENTRY_GET_INIT: - case ADM_SW_IOCTL_MACENTRY_GET_MORE: - - - mMACENTRY = (PMACENTRY)kmalloc(sizeof(MACENTRY), GFP_KERNEL); - rtval = copy_from_user(mMACENTRY, (PMACENTRY)args, sizeof(MACENTRY)); - if (rtval != 0) - { - printk("ADM_SW_IOCTL_MACENTRY: copy from user FAILED!! \n"); - return (-EFAULT); - } - control[0]=(mMACENTRY->mac_addr[1]<<8)+mMACENTRY->mac_addr[0] ; - control[1]=(mMACENTRY->mac_addr[3]<<8)+mMACENTRY->mac_addr[2] ; - control[2]=(mMACENTRY->mac_addr[5]<<8)+mMACENTRY->mac_addr[4] ; - control[3]=(mMACENTRY->fid&0xf)+((mMACENTRY->portmap&0x3f)<<4); - if (((mMACENTRY->info_type)&0x01)) control[4]=(mMACENTRY->ctrl.info_ctrl)+0x1000; //static ,info control - else control[4]=((mMACENTRY->ctrl.age_timer)&0xff);//not static ,agetimer - if (cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT) { - //initial the pointer to the first address - val=0x8000;//busy ,status5[15] - while(val&0x8000){ //check busy ? - ifx_sw_read(0x125, &val); - } - control[5]=0x030;//initial the first address - ifx_sw_write(0x11f,control[5]); - - - val=0x8000;//busy ,status5[15] - while(val&0x8000){ //check busy ? - ifx_sw_read(0x125, &val); - } - - } //if (cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT) - if (cmd==ADM_SW_IOCTL_MACENTRY_ADD) control[5]=0x07;//create a new address - else if (cmd==ADM_SW_IOCTL_MACENTRY_DEL) control[5]=0x01f;//erased an existed address - else if ((cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT)||(cmd==ADM_SW_IOCTL_MACENTRY_GET_MORE)) - control[5]=0x02c;//search by the mac address field - - val=0x8000;//busy ,status5[15] - while(val&0x8000){ //check busy ? - ifx_sw_read(0x125, &val); - } - ifx_sw_write(0x11a,control[0]); - ifx_sw_write(0x11b,control[1]); - ifx_sw_write(0x11c,control[2]); - ifx_sw_write(0x11d,control[3]); - ifx_sw_write(0x11e,control[4]); - ifx_sw_write(0x11f,control[5]); - val=0x8000;//busy ,status5[15] - while(val&0x8000){ //check busy ? - ifx_sw_read(0x125, &val); - } - val=((val&0x7000)>>12);//result ,status5[14:12] - mMACENTRY->result=val; - - if (!val) { - printk(" Command OK!! \n"); - if ((cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT)||(cmd==ADM_SW_IOCTL_MACENTRY_GET_MORE)) { - ifx_sw_read(0x120,&(status[0])); - ifx_sw_read(0x121,&(status[1])); - ifx_sw_read(0x122,&(status[2])); - ifx_sw_read(0x123,&(status[3])); - ifx_sw_read(0x124,&(status[4])); - ifx_sw_read(0x125,&(status[5])); - - - mMACENTRY->mac_addr[0]=(status[0]&0x00ff) ; - mMACENTRY->mac_addr[1]=(status[0]&0xff00)>>8 ; - mMACENTRY->mac_addr[2]=(status[1]&0x00ff) ; - mMACENTRY->mac_addr[3]=(status[1]&0xff00)>>8 ; - mMACENTRY->mac_addr[4]=(status[2]&0x00ff) ; - mMACENTRY->mac_addr[5]=(status[2]&0xff00)>>8 ; - mMACENTRY->fid=(status[3]&0xf); - mMACENTRY->portmap=((status[3]>>4)&0x3f); - if (status[5]&0x2) {//static info_ctrl //status5[1]???? - mMACENTRY->ctrl.info_ctrl=(status[4]&0x00ff); - mMACENTRY->info_type=1; - } - else {//not static age_timer - mMACENTRY->ctrl.age_timer=(status[4]&0x00ff); - mMACENTRY->info_type=0; - } -//status5[13]???? mMACENTRY->occupy=(status[5]&0x02)>>1;//status5[1] - mMACENTRY->occupy=(status[5]&0x02000)>>13;//status5[13] ??? - mMACENTRY->bad=(status[5]&0x04)>>2;//status5[2] - }//if ((cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT)||(cmd==ADM_SW_IOCTL_MACENTRY_GET_MORE)) - - } - else if (val==0x001) - printk(" All Entry Used!! \n"); - else if (val==0x002) - printk(" Entry Not Found!! \n"); - else if (val==0x003) - printk(" Try Next Entry!! \n"); - else if (val==0x005) - printk(" Command Error!! \n"); - else - printk(" UnKnown Error!! \n"); - - copy_to_user((PMACENTRY)args, mMACENTRY,sizeof(MACENTRY)); - - break; - - case ADM_SW_IOCTL_FILTER_ADD: - case ADM_SW_IOCTL_FILTER_DEL: - case ADM_SW_IOCTL_FILTER_GET: - - uPROTOCOLFILTER = (PPROTOCOLFILTER)kmalloc(sizeof(PROTOCOLFILTER), GFP_KERNEL); - rtval = copy_from_user(uPROTOCOLFILTER, (PPROTOCOLFILTER)args, sizeof(PROTOCOLFILTER)); - if (rtval != 0) - { - printk("ADM_SW_IOCTL_FILTER_ADD: copy from user FAILED!! \n"); - return (-EFAULT); - } - - if(cmd==ADM_SW_IOCTL_FILTER_DEL) { //delete filter - uPROTOCOLFILTER->ip_p=00; //delet filter - uPROTOCOLFILTER->action=00; //delete filter - } //delete filter - - ifx_sw_read(((uPROTOCOLFILTER->protocol_filter_num/2)+0x68), &val);//rx68~rx6b,protocol filter0~7 - - if (((uPROTOCOLFILTER->protocol_filter_num)%2)==00){ - if(cmd==ADM_SW_IOCTL_FILTER_GET) uPROTOCOLFILTER->ip_p= val&0x00ff;//get filter ip_p - else val=(val&0xff00)|(uPROTOCOLFILTER->ip_p);//set filter ip_p - } - else { - if(cmd==ADM_SW_IOCTL_FILTER_GET) uPROTOCOLFILTER->ip_p= (val>>8);//get filter ip_p - else val=(val&0x00ff)|((uPROTOCOLFILTER->ip_p)<<8);//set filter ip_p - } - if(cmd!=ADM_SW_IOCTL_FILTER_GET) ifx_sw_write(((uPROTOCOLFILTER->protocol_filter_num/2)+0x68), val);//write rx68~rx6b,protocol filter0~7 - - ifx_sw_read(0x95, &val); //protocol filter action - if(cmd==ADM_SW_IOCTL_FILTER_GET) { - uPROTOCOLFILTER->action= ((val>>(uPROTOCOLFILTER->protocol_filter_num*2))&0x3);//get filter action - copy_to_user((PPROTOCOLFILTER)args, uPROTOCOLFILTER, sizeof(PROTOCOLFILTER)); - - } - else { - val=(val&(~(0x03<<(uPROTOCOLFILTER->protocol_filter_num*2))))|(((uPROTOCOLFILTER->action)&0x03)<<(uPROTOCOLFILTER->protocol_filter_num*2)); - // printk("%d----\n",val); - ifx_sw_write(0x95, val); //write protocol filter action - } - - break; -//adm6996i - - /* others */ - default: - return -EFAULT; - } - /* end of switch */ - return 0; -} - -/* Santosh: handle IGMP protocol filter ADD/DEL/GET */ -int adm_process_protocol_filter_request (unsigned int cmd, PPROTOCOLFILTER uPROTOCOLFILTER) -{ - unsigned int val; //6996i - - if(cmd==ADM_SW_IOCTL_FILTER_DEL) { //delete filter - uPROTOCOLFILTER->ip_p=00; //delet filter - uPROTOCOLFILTER->action=00; //delete filter - } //delete filter - - ifx_sw_read(((uPROTOCOLFILTER->protocol_filter_num/2)+0x68), &val);//rx68~rx6b,protocol filter0~7 - - if (((uPROTOCOLFILTER->protocol_filter_num)%2)==00){ - if(cmd==ADM_SW_IOCTL_FILTER_GET) uPROTOCOLFILTER->ip_p= val&0x00ff;//get filter ip_p - else val=(val&0xff00)|(uPROTOCOLFILTER->ip_p);//set filter ip_p - } - else { - if(cmd==ADM_SW_IOCTL_FILTER_GET) uPROTOCOLFILTER->ip_p= (val>>8);//get filter ip_p - else val=(val&0x00ff)|((uPROTOCOLFILTER->ip_p)<<8);//set filter ip_p - } - if(cmd!=ADM_SW_IOCTL_FILTER_GET) ifx_sw_write(((uPROTOCOLFILTER->protocol_filter_num/2)+0x68), val);//write rx68~rx6b,protocol filter0~7 - - ifx_sw_read(0x95, &val); //protocol filter action - if(cmd==ADM_SW_IOCTL_FILTER_GET) { - uPROTOCOLFILTER->action= ((val>>(uPROTOCOLFILTER->protocol_filter_num*2))&0x3);//get filter action - } - else { - val=(val&(~(0x03<<(uPROTOCOLFILTER->protocol_filter_num*2))))|(((uPROTOCOLFILTER->action)&0x03)<<(uPROTOCOLFILTER->protocol_filter_num*2)); - ifx_sw_write(0x95, val); //write protocol filter action - } - - return 0; -} - - -/* Santosh: function for MAC ENTRY ADD/DEL/GET */ - -int adm_process_mac_table_request (unsigned int cmd, PMACENTRY mMACENTRY) -{ - unsigned int rtval; - unsigned int val; //6996i - unsigned int control[6] ; //6996i - unsigned int status[6] ; //6996i - - // printk ("adm_process_mac_table_request: enter\n"); - - control[0]=(mMACENTRY->mac_addr[1]<<8)+mMACENTRY->mac_addr[0] ; - control[1]=(mMACENTRY->mac_addr[3]<<8)+mMACENTRY->mac_addr[2] ; - control[2]=(mMACENTRY->mac_addr[5]<<8)+mMACENTRY->mac_addr[4] ; - control[3]=(mMACENTRY->fid&0xf)+((mMACENTRY->portmap&0x3f)<<4); - - if (((mMACENTRY->info_type)&0x01)) control[4]=(mMACENTRY->ctrl.info_ctrl)+0x1000; //static ,info control - else control[4]=((mMACENTRY->ctrl.age_timer)&0xff);//not static ,agetimer - if (cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT) { - //initial the pointer to the first address - val=0x8000;//busy ,status5[15] - while(val&0x8000){ //check busy ? - ifx_sw_read(0x125, &val); - } - control[5]=0x030;//initial the first address - ifx_sw_write(0x11f,control[5]); - - - val=0x8000;//busy ,status5[15] - while(val&0x8000){ //check busy ? - ifx_sw_read(0x125, &val); - } - - } //if (cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT) - if (cmd==ADM_SW_IOCTL_MACENTRY_ADD) control[5]=0x07;//create a new address - else if (cmd==ADM_SW_IOCTL_MACENTRY_DEL) control[5]=0x01f;//erased an existed address - else if ((cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT)||(cmd==ADM_SW_IOCTL_MACENTRY_GET_MORE)) - control[5]=0x02c;//search by the mac address field - - val=0x8000;//busy ,status5[15] - while(val&0x8000){ //check busy ? - ifx_sw_read(0x125, &val); - } - ifx_sw_write(0x11a,control[0]); - ifx_sw_write(0x11b,control[1]); - ifx_sw_write(0x11c,control[2]); - ifx_sw_write(0x11d,control[3]); - ifx_sw_write(0x11e,control[4]); - ifx_sw_write(0x11f,control[5]); - val=0x8000;//busy ,status5[15] - while(val&0x8000){ //check busy ? - ifx_sw_read(0x125, &val); - } - val=((val&0x7000)>>12);//result ,status5[14:12] - mMACENTRY->result=val; - - if (!val) { - printk(" Command OK!! \n"); - if ((cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT)||(cmd==ADM_SW_IOCTL_MACENTRY_GET_MORE)) { - ifx_sw_read(0x120,&(status[0])); - ifx_sw_read(0x121,&(status[1])); - ifx_sw_read(0x122,&(status[2])); - ifx_sw_read(0x123,&(status[3])); - ifx_sw_read(0x124,&(status[4])); - ifx_sw_read(0x125,&(status[5])); - - - mMACENTRY->mac_addr[0]=(status[0]&0x00ff) ; - mMACENTRY->mac_addr[1]=(status[0]&0xff00)>>8 ; - mMACENTRY->mac_addr[2]=(status[1]&0x00ff) ; - mMACENTRY->mac_addr[3]=(status[1]&0xff00)>>8 ; - mMACENTRY->mac_addr[4]=(status[2]&0x00ff) ; - mMACENTRY->mac_addr[5]=(status[2]&0xff00)>>8 ; - mMACENTRY->fid=(status[3]&0xf); - mMACENTRY->portmap=((status[3]>>4)&0x3f); - if (status[5]&0x2) {//static info_ctrl //status5[1]???? - mMACENTRY->ctrl.info_ctrl=(status[4]&0x00ff); - mMACENTRY->info_type=1; - } - else {//not static age_timer - mMACENTRY->ctrl.age_timer=(status[4]&0x00ff); - mMACENTRY->info_type=0; - } -//status5[13]???? mMACENTRY->occupy=(status[5]&0x02)>>1;//status5[1] - mMACENTRY->occupy=(status[5]&0x02000)>>13;//status5[13] ??? - mMACENTRY->bad=(status[5]&0x04)>>2;//status5[2] - }//if ((cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT)||(cmd==ADM_SW_IOCTL_MACENTRY_GET_MORE)) - - } - else if (val==0x001) - printk(" All Entry Used!! \n"); - else if (val==0x002) - printk(" Entry Not Found!! \n"); - else if (val==0x003) - printk(" Try Next Entry!! \n"); - else if (val==0x005) - printk(" Command Error!! \n"); - else - printk(" UnKnown Error!! \n"); - - // printk ("adm_process_mac_table_request: Exit\n"); - return 0; -} - -/* Santosh: End of function for MAC ENTRY ADD/DEL*/ -struct file_operations adm_ops = -{ - read: adm_read, - write: adm_write, - open: adm_open, - release: adm_release, - ioctl: adm_ioctl -}; - -int adm_proc(char *buf, char **start, off_t offset, int count, int *eof, void *data) -{ - int len = 0; - - len += sprintf(buf+len, " ************ Registers ************ \n"); - *eof = 1; - return len; -} - -int __init init_adm6996_module(void) -{ - unsigned int val = 000; - unsigned int val1 = 000; - - printk("Loading ADM6996 driver... \n"); - - /* if running on adm5120 */ - /* set GPIO 0~2 as adm6996 control pins */ - //outl(0x003f3f00, 0x12000028); - /* enable switch port 5 (MII) as RMII mode (5120MAC <-> 6996MAC) */ - //outl(0x18a, 0x12000030); - /* group adm5120 port 1 ~ 5 as VLAN0, port 5 & 6(CPU) as VLAN1 */ - //outl(0x417e, 0x12000040); - /* end adm5120 fixup */ -#ifdef ADM6996_MDC_MDIO_MODE //smi mode //000001.joelin - register_chrdev(69, "adm6996", &adm_ops); - AMAZON_SW_REG(AMAZON_SW_MDIO_CFG) = 0x27be; - AMAZON_SW_REG(AMAZON_SW_EPHY) = 0xfc; - adm6996_mode=adm6996i; - ifx_sw_read(0xa0, &val); - ifx_sw_read(0xa1, &val1); - val=((val1&0x0f)<<16)|val; - printk ("\nADM6996 SMI Mode-"); - printk ("Chip ID:%5x \n ", val); -#else //000001.joelin - - AMAZON_SW_REG(AMAZON_SW_MDIO_CFG) = 0x2c50; - AMAZON_SW_REG(AMAZON_SW_EPHY) = 0xff; - - AMAZON_SW_REG(AMAZON_GPIO_P1_ALTSEL0) &= ~(GPIO_MDIO|GPIO_MDCS|GPIO_MDC); - AMAZON_SW_REG(AMAZON_GPIO_P1_ALTSEL1) &= ~(GPIO_MDIO|GPIO_MDCS|GPIO_MDC); - AMAZON_SW_REG(AMAZON_GPIO_P1_OD) |= (GPIO_MDIO|GPIO_MDCS|GPIO_MDC); - - ifx_gpio_init(); - register_chrdev(69, "adm6996", &adm_ops); - mdelay(100); - - /* create proc entries */ - // create_proc_read_entry("admide", 0, NULL, admide_proc, NULL); - -//joelin adm6996i support start - adm6996_mode=adm6996i; - ifx_sw_read(0xa0, &val); - adm6996_mode=adm6996l; - ifx_sw_read(0x200, &val1); -// printk ("\n %0x \n",val1); - if ((val&0xfff0)==0x1020) { - printk ("\n ADM6996I .. \n"); - adm6996_mode=adm6996i; - } - else if ((val1&0xffffff00)==0x71000) {//71010 or 71020 - printk ("\n ADM6996LC .. \n"); - adm6996_mode=adm6996lc; - } - else { - printk ("\n ADM6996L .. \n"); - adm6996_mode=adm6996l; - } -#endif //ADM6996_MDC_MDIO_MODE //smi mode //000001.joelin - - if ((adm6996_mode==adm6996lc)||(adm6996_mode==adm6996i)){ -#if 0 /* removed by MarsLin */ - ifx_sw_write(0x29,0xc000); - ifx_sw_write(0x30,0x0985); -#else - ifx_sw_read(0xa0, &val); - if (val == 0x1021) // for both 6996LC and 6996I, only AB version need the patch - ifx_sw_write(0x29, 0x9000); - ifx_sw_write(0x30,0x0985); -#endif - } -//joelin adm6996i support end - return 0; -} - -void __exit cleanup_adm6996_module(void) -{ - printk("Free ADM device driver... \n"); - - unregister_chrdev(69, "adm6996"); - - /* remove proc entries */ - // remove_proc_entry("admide", NULL); -} - -/* MarsLin, add start */ -#if defined(CONFIG_IFX_NFEXT_AMAZON_SWITCH_PHYPORT) || defined(CONFIG_IFX_NFEXT_AMAZON_SWITCH_PHYPORT_MODULE) - #define SET_BIT(reg, mask) reg |= (mask) - #define CLEAR_BIT(reg, mask) reg &= (~mask) - static int ifx_hw_reset(void) - { - CLEAR_BIT((*AMAZON_GPIO_P0_ALTSEL0),0x2000); - CLEAR_BIT((*AMAZON_GPIO_P0_ALTSEL1),0x2000); - SET_BIT((*AMAZON_GPIO_P0_OD),0x2000); - SET_BIT((*AMAZON_GPIO_P0_DIR), 0x2000); - CLEAR_BIT((*AMAZON_GPIO_P0_OUT), 0x2000); - mdelay(500); - SET_BIT((*AMAZON_GPIO_P0_OUT), 0x2000); - cleanup_adm6996_module(); - return init_adm6996_module(); - } - int (*adm6996_hw_reset)(void) = ifx_hw_reset; - EXPORT_SYMBOL(adm6996_hw_reset); - EXPORT_SYMBOL(adm6996_mode); - int (*adm6996_sw_read)(unsigned int addr, unsigned int *data) = ifx_sw_read; - EXPORT_SYMBOL(adm6996_sw_read); - int (*adm6996_sw_write)(unsigned int addr, unsigned int data) = ifx_sw_write; - EXPORT_SYMBOL(adm6996_sw_write); -#endif -/* MarsLin, add end */ - -/* Santosh: for IGMP proxy/snooping, Begin */ -EXPORT_SYMBOL (adm_process_mac_table_request); -EXPORT_SYMBOL (adm_process_protocol_filter_request); -/* Santosh: for IGMP proxy/snooping, End */ - -MODULE_DESCRIPTION("ADMtek 6996 Driver"); -MODULE_AUTHOR("Joe Lin "); -MODULE_LICENSE("GPL"); - -module_init(init_adm6996_module); -module_exit(cleanup_adm6996_module); - diff --git a/target/linux/amazon/files/drivers/net/admmod.c b/target/linux/amazon/files/drivers/net/admmod.c new file mode 100644 index 0000000000..70ba1496a1 --- /dev/null +++ b/target/linux/amazon/files/drivers/net/admmod.c @@ -0,0 +1,1484 @@ +/****************************************************************************** + Copyright (c) 2004, Infineon Technologies. All rights reserved. + + No Warranty + Because the program is licensed free of charge, there is no warranty for + the program, to the extent permitted by applicable law. Except when + otherwise stated in writing the copyright holders and/or other parties + provide the program "as is" without warranty of any kind, either + expressed or implied, including, but not limited to, the implied + warranties of merchantability and fitness for a particular purpose. The + entire risk as to the quality and performance of the program is with + you. should the program prove defective, you assume the cost of all + necessary servicing, repair or correction. + + In no event unless required by applicable law or agreed to in writing + will any copyright holder, or any other party who may modify and/or + redistribute the program as permitted above, be liable to you for + damages, including any general, special, incidental or consequential + damages arising out of the use or inability to use the program + (including but not limited to loss of data or data being rendered + inaccurate or losses sustained by you or third parties or a failure of + the program to operate with any other programs), even if such holder or + other party has been advised of the possibility of such damages. + ****************************************************************************** + Module : admmod.c + Date : 2004-09-01 + Description : JoeLin + Remarks: + + Revision: + MarsLin, add to support VLAN + + *****************************************************************************/ +//000001.joelin 2005/06/02 add"ADM6996_MDC_MDIO_MODE" define, +// if define ADM6996_MDC_MDIO_MODE==> ADM6996LC and ADM6996I will be in MDIO/MDC(SMI)(16 bit) mode, +// amazon should contrl ADM6996 by MDC/MDIO pin +// if undef ADM6996_MDC_MDIO_MODE==> ADM6996 will be in EEProm(32 bit) mode, +// amazon should contrl ADM6996 by GPIO15,16,17,18 pin +/* 507281:linmars 2005/07/28 support MDIO/EEPROM config mode */ +/* 509201:linmars remove driver testing codes */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +//#include + + +unsigned int ifx_sw_conf[ADM_SW_MAX_PORT_NUM+1] = \ + {ADM_SW_PORT0_CONF, ADM_SW_PORT1_CONF, ADM_SW_PORT2_CONF, \ + ADM_SW_PORT3_CONF, ADM_SW_PORT4_CONF, ADM_SW_PORT5_CONF}; +unsigned int ifx_sw_bits[8] = \ + {0x1, 0x3, 0x7, 0xf, 0x1f, 0x3f, 0x7f, 0xff}; +unsigned int ifx_sw_vlan_port[6] = {0, 2, 4, 6, 7, 8}; +//050613:fchang +/* 507281:linmars start */ +#ifdef CONFIG_SWITCH_ADM6996_MDIO +#define ADM6996_MDC_MDIO_MODE 1 //000001.joelin +#else +#undef ADM6996_MDC_MDIO_MODE +#endif +/* 507281:linmars end */ +#define adm6996i 0 +#define adm6996lc 1 +#define adm6996l 2 +unsigned int adm6996_mode=adm6996i; +/* + initialize GPIO pins. + output mode, low +*/ +void ifx_gpio_init(void) +{ + //GPIO16,17,18 direction:output + //GPIO16,17,18 output 0 + + AMAZON_SW_REG(AMAZON_GPIO_P1_DIR) |= (GPIO_MDIO|GPIO_MDCS|GPIO_MDC); + AMAZON_SW_REG(AMAZON_GPIO_P1_OUT) =AMAZON_SW_REG(AMAZON_GPIO_P1_IN)& ~(GPIO_MDIO|GPIO_MDCS|GPIO_MDC); + +} + +/* read one bit from mdio port */ +int ifx_sw_mdio_readbit(void) +{ + //int val; + + //val = (AMAZON_SW_REG(GPIO_conf0_REG) & GPIO0_INPUT_MASK) >> 8; + //return val; + //GPIO16 + return AMAZON_SW_REG(AMAZON_GPIO_P1_IN)&1; +} + +/* + MDIO mode selection + 1 -> output + 0 -> input + + switch input/output mode of GPIO 0 +*/ +void ifx_mdio_mode(int mode) +{ +// AMAZON_SW_REG(GPIO_conf0_REG) = mode ? GPIO_ENABLEBITS : +// ((GPIO_ENABLEBITS | MDIO_INPUT) & ~MDIO_OUTPUT_EN); + mode?(AMAZON_SW_REG(AMAZON_GPIO_P1_DIR)|=GPIO_MDIO): + (AMAZON_SW_REG(AMAZON_GPIO_P1_DIR)&=~GPIO_MDIO); + /*int r=AMAZON_SW_REG(AMAZON_GPIO_P1_DIR); + mode?(r|=GPIO_MDIO):(r&=~GPIO_MDIO); + AMAZON_SW_REG(AMAZON_GPIO_P1_DIR)=r;*/ +} + +void ifx_mdc_hi(void) +{ + //GPIO_SET_HI(GPIO_MDC); + //AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)|=GPIO_MDC; + /*int r=AMAZON_SW_REG(AMAZON_GPIO_P1_OUT); + r|=GPIO_MDC; + AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=r;*/ + + AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=AMAZON_SW_REG(AMAZON_GPIO_P1_IN)|GPIO_MDC; +} + +void ifx_mdio_hi(void) +{ + //GPIO_SET_HI(GPIO_MDIO); + //AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)|=GPIO_MDIO; + /*int r=AMAZON_SW_REG(AMAZON_GPIO_P1_OUT); + r|=GPIO_MDIO; + AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=r;*/ + + AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=AMAZON_SW_REG(AMAZON_GPIO_P1_IN)|GPIO_MDIO; +} + +void ifx_mdcs_hi(void) +{ + //GPIO_SET_HI(GPIO_MDCS); + //AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)|=GPIO_MDCS; + /*int r=AMAZON_SW_REG(AMAZON_GPIO_P1_OUT); + r|=GPIO_MDCS; + AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=r;*/ + + AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=AMAZON_SW_REG(AMAZON_GPIO_P1_IN)|GPIO_MDCS; +} + +void ifx_mdc_lo(void) +{ + //GPIO_SET_LOW(GPIO_MDC); + //AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)&=~GPIO_MDC; + /*int r=AMAZON_SW_REG(AMAZON_GPIO_P1_OUT); + r&=~GPIO_MDC; + AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=r;*/ + + AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=AMAZON_SW_REG(AMAZON_GPIO_P1_IN)&(~GPIO_MDC); +} + +void ifx_mdio_lo(void) +{ + //GPIO_SET_LOW(GPIO_MDIO); + //AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)&=~GPIO_MDIO; + /*int r=AMAZON_SW_REG(AMAZON_GPIO_P1_OUT); + r&=~GPIO_MDIO; + AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=r;*/ + + AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=AMAZON_SW_REG(AMAZON_GPIO_P1_IN)&(~GPIO_MDIO); +} + +void ifx_mdcs_lo(void) +{ + //GPIO_SET_LOW(GPIO_MDCS); + //AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)&=~GPIO_MDCS; + /*int r=AMAZON_SW_REG(AMAZON_GPIO_P1_OUT); + r&=~GPIO_MDCS; + AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=r;*/ + + AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=AMAZON_SW_REG(AMAZON_GPIO_P1_IN)&(~GPIO_MDCS); +} + +/* + mdc pulse + 0 -> 1 -> 0 +*/ +static void ifx_sw_mdc_pulse(void) +{ + ifx_mdc_lo(); + udelay(ADM_SW_MDC_DOWN_DELAY); + ifx_mdc_hi(); + udelay(ADM_SW_MDC_UP_DELAY); + ifx_mdc_lo(); +} + +/* + mdc toggle + 1 -> 0 +*/ +static void ifx_sw_mdc_toggle(void) +{ + ifx_mdc_hi(); + udelay(ADM_SW_MDC_UP_DELAY); + ifx_mdc_lo(); + udelay(ADM_SW_MDC_DOWN_DELAY); +} + +/* + enable eeprom write + For ATC 93C66 type EEPROM; accessing ADM6996 internal EEPROM type registers +*/ +static void ifx_sw_eeprom_write_enable(void) +{ + unsigned int op; + + ifx_mdcs_lo(); + ifx_mdc_lo(); + ifx_mdio_hi(); + udelay(ADM_SW_CS_DELAY); + /* enable chip select */ + ifx_mdcs_hi(); + udelay(ADM_SW_CS_DELAY); + /* start bit */ + ifx_mdio_hi(); + ifx_sw_mdc_pulse(); + + /* eeprom write enable */ + op = ADM_SW_BIT_MASK_4; + while (op) + { + if (op & ADM_SW_EEPROM_WRITE_ENABLE) + ifx_mdio_hi(); + else + ifx_mdio_lo(); + + ifx_sw_mdc_pulse(); + op >>= 1; + } + + op = ADM_SW_BIT_MASK_1 << (EEPROM_TYPE - 3); + while (op) + { + ifx_mdio_lo(); + ifx_sw_mdc_pulse(); + op >>= 1; + } + /* disable chip select */ + ifx_mdcs_lo(); + udelay(ADM_SW_CS_DELAY); + ifx_sw_mdc_pulse(); +} + +/* + disable eeprom write +*/ +static void ifx_sw_eeprom_write_disable(void) +{ + unsigned int op; + + ifx_mdcs_lo(); + ifx_mdc_lo(); + ifx_mdio_hi(); + udelay(ADM_SW_CS_DELAY); + /* enable chip select */ + ifx_mdcs_hi(); + udelay(ADM_SW_CS_DELAY); + + /* start bit */ + ifx_mdio_hi(); + ifx_sw_mdc_pulse(); + /* eeprom write disable */ + op = ADM_SW_BIT_MASK_4; + while (op) + { + if (op & ADM_SW_EEPROM_WRITE_DISABLE) + ifx_mdio_hi(); + else + ifx_mdio_lo(); + + ifx_sw_mdc_pulse(); + op >>= 1; + } + + op = ADM_SW_BIT_MASK_1 << (EEPROM_TYPE - 3); + while (op) + { + ifx_mdio_lo(); + + ifx_sw_mdc_pulse(); + op >>= 1; + } + /* disable chip select */ + ifx_mdcs_lo(); + udelay(ADM_SW_CS_DELAY); + ifx_sw_mdc_pulse(); +} + +/* + read registers from ADM6996 + serial registers start at 0x200 (addr bit 9 = 1b) + EEPROM registers -> 16bits; Serial registers -> 32bits +*/ +#ifdef ADM6996_MDC_MDIO_MODE //smi mode//000001.joelin +static int ifx_sw_read_adm6996i_smi(unsigned int addr, unsigned int *dat) +{ + addr=(addr<<16)&0x3ff0000; + AMAZON_SW_REG(AMAZON_SW_MDIO_ACC) =(0xC0000000|addr); + while ((AMAZON_SW_REG(AMAZON_SW_MDIO_ACC))&0x80000000){}; + *dat=((AMAZON_SW_REG(AMAZON_SW_MDIO_ACC))&0x0FFFF); + return 0; +} +#endif + +static int ifx_sw_read_adm6996i(unsigned int addr, unsigned int *dat) +{ + unsigned int op; + + ifx_gpio_init(); + + ifx_mdcs_hi(); + udelay(ADM_SW_CS_DELAY); + + ifx_mdcs_lo(); + ifx_mdc_lo(); + ifx_mdio_lo(); + + udelay(ADM_SW_CS_DELAY); + + /* preamble, 32 bit 1 */ + ifx_mdio_hi(); + op = ADM_SW_BIT_MASK_32; + while (op) + { + ifx_sw_mdc_pulse(); + op >>= 1; + } + + /* command start (01b) */ + op = ADM_SW_BIT_MASK_2; + while (op) + { + if (op & ADM_SW_SMI_START) + ifx_mdio_hi(); + else + ifx_mdio_lo(); + + ifx_sw_mdc_pulse(); + op >>= 1; + } + + /* read command (10b) */ + op = ADM_SW_BIT_MASK_2; + while (op) + { + if (op & ADM_SW_SMI_READ) + ifx_mdio_hi(); + else + ifx_mdio_lo(); + + ifx_sw_mdc_pulse(); + op >>= 1; + } + + /* send address A9 ~ A0 */ + op = ADM_SW_BIT_MASK_10; + while (op) + { + if (op & addr) + ifx_mdio_hi(); + else + ifx_mdio_lo(); + + ifx_sw_mdc_pulse(); + op >>= 1; + } + + /* turnaround bits */ + op = ADM_SW_BIT_MASK_2; + ifx_mdio_hi(); + while (op) + { + ifx_sw_mdc_pulse(); + op >>= 1; + } + + udelay(ADM_SW_MDC_DOWN_DELAY); + + /* set MDIO pin to input mode */ + ifx_mdio_mode(ADM_SW_MDIO_INPUT); + + /* start read data */ + *dat = 0; +//adm6996i op = ADM_SW_BIT_MASK_32; + op = ADM_SW_BIT_MASK_16;//adm6996i + while (op) + { + *dat <<= 1; + if (ifx_sw_mdio_readbit()) *dat |= 1; + ifx_sw_mdc_toggle(); + + op >>= 1; + } + + /* set MDIO to output mode */ + ifx_mdio_mode(ADM_SW_MDIO_OUTPUT); + + /* dummy clock */ + op = ADM_SW_BIT_MASK_4; + ifx_mdio_lo(); + while(op) + { + ifx_sw_mdc_pulse(); + op >>= 1; + } + + ifx_mdc_lo(); + ifx_mdio_lo(); + ifx_mdcs_hi(); + + /* EEPROM registers */ +//adm6996i if (!(addr & 0x200)) +//adm6996i { +//adm6996i if (addr % 2) +//adm6996i *dat >>= 16; +//adm6996i else +//adm6996i *dat &= 0xffff; +//adm6996i } + + return 0; +} +//adm6996 +static int ifx_sw_read_adm6996l(unsigned int addr, unsigned int *dat) +{ + unsigned int op; + + ifx_gpio_init(); + + ifx_mdcs_hi(); + udelay(ADM_SW_CS_DELAY); + + ifx_mdcs_lo(); + ifx_mdc_lo(); + ifx_mdio_lo(); + + udelay(ADM_SW_CS_DELAY); + + /* preamble, 32 bit 1 */ + ifx_mdio_hi(); + op = ADM_SW_BIT_MASK_32; + while (op) + { + ifx_sw_mdc_pulse(); + op >>= 1; + } + + /* command start (01b) */ + op = ADM_SW_BIT_MASK_2; + while (op) + { + if (op & ADM_SW_SMI_START) + ifx_mdio_hi(); + else + ifx_mdio_lo(); + + ifx_sw_mdc_pulse(); + op >>= 1; + } + + /* read command (10b) */ + op = ADM_SW_BIT_MASK_2; + while (op) + { + if (op & ADM_SW_SMI_READ) + ifx_mdio_hi(); + else + ifx_mdio_lo(); + + ifx_sw_mdc_pulse(); + op >>= 1; + } + + /* send address A9 ~ A0 */ + op = ADM_SW_BIT_MASK_10; + while (op) + { + if (op & addr) + ifx_mdio_hi(); + else + ifx_mdio_lo(); + + ifx_sw_mdc_pulse(); + op >>= 1; + } + + /* turnaround bits */ + op = ADM_SW_BIT_MASK_2; + ifx_mdio_hi(); + while (op) + { + ifx_sw_mdc_pulse(); + op >>= 1; + } + + udelay(ADM_SW_MDC_DOWN_DELAY); + + /* set MDIO pin to input mode */ + ifx_mdio_mode(ADM_SW_MDIO_INPUT); + + /* start read data */ + *dat = 0; + op = ADM_SW_BIT_MASK_32; + while (op) + { + *dat <<= 1; + if (ifx_sw_mdio_readbit()) *dat |= 1; + ifx_sw_mdc_toggle(); + + op >>= 1; + } + + /* set MDIO to output mode */ + ifx_mdio_mode(ADM_SW_MDIO_OUTPUT); + + /* dummy clock */ + op = ADM_SW_BIT_MASK_4; + ifx_mdio_lo(); + while(op) + { + ifx_sw_mdc_pulse(); + op >>= 1; + } + + ifx_mdc_lo(); + ifx_mdio_lo(); + ifx_mdcs_hi(); + + /* EEPROM registers */ + if (!(addr & 0x200)) + { + if (addr % 2) + *dat >>= 16; + else + *dat &= 0xffff; + } + + return 0; +} + +static int ifx_sw_read(unsigned int addr, unsigned int *dat) +{ +#ifdef ADM6996_MDC_MDIO_MODE //smi mode ////000001.joelin + ifx_sw_read_adm6996i_smi(addr,dat); +#else + if (adm6996_mode==adm6996i) ifx_sw_read_adm6996i(addr,dat); + else ifx_sw_read_adm6996l(addr,dat); +#endif + return 0; + +} + +/* + write register to ADM6996 eeprom registers +*/ +//for adm6996i -start +#ifdef ADM6996_MDC_MDIO_MODE //smi mode //000001.joelin +static int ifx_sw_write_adm6996i_smi(unsigned int addr, unsigned int dat) +{ + + AMAZON_SW_REG(AMAZON_SW_MDIO_ACC) = ((addr<<16)&0x3ff0000)|dat|0x80000000; + while ((AMAZON_SW_REG(AMAZON_SW_MDIO_ACC))&0x80000000){}; + + return 0; + +} +#endif //ADM6996_MDC_MDIO_MODE //000001.joelin + +static int ifx_sw_write_adm6996i(unsigned int addr, unsigned int dat) +{ + unsigned int op; + + ifx_gpio_init(); + + ifx_mdcs_hi(); + udelay(ADM_SW_CS_DELAY); + + ifx_mdcs_lo(); + ifx_mdc_lo(); + ifx_mdio_lo(); + + udelay(ADM_SW_CS_DELAY); + + /* preamble, 32 bit 1 */ + ifx_mdio_hi(); + op = ADM_SW_BIT_MASK_32; + while (op) + { + ifx_sw_mdc_pulse(); + op >>= 1; + } + + /* command start (01b) */ + op = ADM_SW_BIT_MASK_2; + while (op) + { + if (op & ADM_SW_SMI_START) + ifx_mdio_hi(); + else + ifx_mdio_lo(); + + ifx_sw_mdc_pulse(); + op >>= 1; + } + + /* write command (01b) */ + op = ADM_SW_BIT_MASK_2; + while (op) + { + if (op & ADM_SW_SMI_WRITE) + ifx_mdio_hi(); + else + ifx_mdio_lo(); + + ifx_sw_mdc_pulse(); + op >>= 1; + } + + /* send address A9 ~ A0 */ + op = ADM_SW_BIT_MASK_10; + while (op) + { + if (op & addr) + ifx_mdio_hi(); + else + ifx_mdio_lo(); + + ifx_sw_mdc_pulse(); + op >>= 1; + } + + /* turnaround bits */ + op = ADM_SW_BIT_MASK_2; + ifx_mdio_hi(); + while (op) + { + ifx_sw_mdc_pulse(); + op >>= 1; + } + + udelay(ADM_SW_MDC_DOWN_DELAY); + + /* set MDIO pin to output mode */ + ifx_mdio_mode(ADM_SW_MDIO_OUTPUT); + + + /* start write data */ + op = ADM_SW_BIT_MASK_16; + while (op) + { + if (op & dat) + ifx_mdio_hi(); + else + ifx_mdio_lo(); + + ifx_sw_mdc_toggle(); + op >>= 1; + } + + // /* set MDIO to output mode */ + // ifx_mdio_mode(ADM_SW_MDIO_OUTPUT); + + /* dummy clock */ + op = ADM_SW_BIT_MASK_4; + ifx_mdio_lo(); + while(op) + { + ifx_sw_mdc_pulse(); + op >>= 1; + } + + ifx_mdc_lo(); + ifx_mdio_lo(); + ifx_mdcs_hi(); + + /* EEPROM registers */ +//adm6996i if (!(addr & 0x200)) +//adm6996i { +//adm6996i if (addr % 2) +//adm6996i *dat >>= 16; +//adm6996i else +//adm6996i *dat &= 0xffff; +//adm6996i } + + return 0; +} +//for adm6996i-end +static int ifx_sw_write_adm6996l(unsigned int addr, unsigned int dat) +{ + unsigned int op; + + ifx_gpio_init(); + + /* enable write */ + ifx_sw_eeprom_write_enable(); + + /* chip select */ + ifx_mdcs_hi(); + udelay(ADM_SW_CS_DELAY); + + /* issue write command */ + /* start bit */ + ifx_mdio_hi(); + ifx_sw_mdc_pulse(); + + /* EEPROM write command */ + op = ADM_SW_BIT_MASK_2; + while (op) + { + if (op & ADM_SW_EEPROM_WRITE) + ifx_mdio_hi(); + else + ifx_mdio_lo(); + + ifx_sw_mdc_pulse(); + op >>= 1; + } + + /* send address A7 ~ A0 */ + op = ADM_SW_BIT_MASK_1 << (EEPROM_TYPE - 1); + + while (op) + { + if (op & addr) + ifx_mdio_hi(); + else + ifx_mdio_lo(); + + ifx_sw_mdc_toggle(); + op >>= 1; + } + + /* start write data */ + op = ADM_SW_BIT_MASK_16; + while (op) + { + if (op & dat) + ifx_mdio_hi(); + else + ifx_mdio_lo(); + + ifx_sw_mdc_toggle(); + op >>= 1; + } + + /* disable cs & wait 1 clock */ + ifx_mdcs_lo(); + udelay(ADM_SW_CS_DELAY); + ifx_sw_mdc_toggle(); + + ifx_sw_eeprom_write_disable(); + + return 0; +} + +static int ifx_sw_write(unsigned int addr, unsigned int dat) +{ +#ifdef ADM6996_MDC_MDIO_MODE //smi mode ////000001.joelin + ifx_sw_write_adm6996i_smi(addr,dat); +#else //000001.joelin + if (adm6996_mode==adm6996i) ifx_sw_write_adm6996i(addr,dat); + else ifx_sw_write_adm6996l(addr,dat); +#endif //000001.joelin + return 0; +} + +/* + do switch PHY reset +*/ +int ifx_sw_reset(void) +{ + /* reset PHY */ + ifx_sw_write(ADM_SW_PHY_RESET, 0); + + return 0; +} + +/* 509201:linmars start */ +#if 0 +/* + check port status +*/ +int ifx_check_port_status(int port) +{ + unsigned int val; + + if ((port < 0) || (port > ADM_SW_MAX_PORT_NUM)) + { + ifx_printf(("error on port number (%d)!!\n", port)); + return -1; + } + + ifx_sw_read(ifx_sw_conf[port], &val); + if (ifx_sw_conf[port]%2) val >>= 16; + /* only 16bits are effective */ + val &= 0xFFFF; + + ifx_printf(("Port %d status (%.8x): \n", port, val)); + + if (val & ADM_SW_PORT_FLOWCTL) + ifx_printf(("\t802.3x flow control supported!\n")); + else + ifx_printf(("\t802.3x flow control not supported!\n")); + + if (val & ADM_SW_PORT_AN) + ifx_printf(("\tAuto negotiation ON!\n")); + else + ifx_printf(("\tAuto negotiation OFF!\n")); + + if (val & ADM_SW_PORT_100M) + ifx_printf(("\tLink at 100M!\n")); + else + ifx_printf(("\tLink at 10M!\n")); + + if (val & ADM_SW_PORT_FULL) + ifx_printf(("\tFull duplex!\n")); + else + ifx_printf(("\tHalf duplex!\n")); + + if (val & ADM_SW_PORT_DISABLE) + ifx_printf(("\tPort disabled!\n")); + else + ifx_printf(("\tPort enabled!\n")); + + if (val & ADM_SW_PORT_TOS) + ifx_printf(("\tTOS enabled!\n")); + else + ifx_printf(("\tTOS disabled!\n")); + + if (val & ADM_SW_PORT_PPRI) + ifx_printf(("\tPort priority first!\n")); + else + ifx_printf(("\tVLAN or TOS priority first!\n")); + + if (val & ADM_SW_PORT_MDIX) + ifx_printf(("\tAuto MDIX!\n")); + else + ifx_printf(("\tNo auto MDIX\n")); + + ifx_printf(("\tPVID: %d\n", \ + ((val >> ADM_SW_PORT_PVID_SHIFT)&ifx_sw_bits[ADM_SW_PORT_PVID_BITS]))); + + return 0; +} +/* + initialize a VLAN + clear all VLAN bits +*/ +int ifx_sw_vlan_init(int vlanid) +{ + ifx_sw_write(ADM_SW_VLAN0_CONF + vlanid, 0); + + return 0; +} + +/* + add a port to certain vlan +*/ +int ifx_sw_vlan_add(int port, int vlanid) +{ + int reg = 0; + + if ((port < 0) || (port > ADM_SW_MAX_PORT_NUM) || (vlanid < 0) || + (vlanid > ADM_SW_MAX_VLAN_NUM)) + { + ifx_printf(("Port number or VLAN number ERROR!!\n")); + return -1; + } + ifx_sw_read(ADM_SW_VLAN0_CONF + vlanid, ®); + reg |= (1 << ifx_sw_vlan_port[port]); + ifx_sw_write(ADM_SW_VLAN0_CONF + vlanid, reg); + + return 0; +} + +/* + delete a given port from certain vlan +*/ +int ifx_sw_vlan_del(int port, int vlanid) +{ + unsigned int reg = 0; + + if ((port < 0) || (port > ADM_SW_MAX_PORT_NUM) || (vlanid < 0) || (vlanid > ADM_SW_MAX_VLAN_NUM)) + { + ifx_printf(("Port number or VLAN number ERROR!!\n")); + return -1; + } + ifx_sw_read(ADM_SW_VLAN0_CONF + vlanid, ®); + reg &= ~(1 << ifx_sw_vlan_port[port]); + ifx_sw_write(ADM_SW_VLAN0_CONF + vlanid, reg); + + return 0; +} + +/* + default VLAN setting + + port 0~3 as untag port and PVID = 1 + VLAN1: port 0~3 and port 5 (MII) +*/ +static int ifx_sw_init(void) +{ + ifx_printf(("Setting default ADM6996 registers... \n")); + + /* MAC clone, 802.1q based VLAN */ + ifx_sw_write(ADM_SW_VLAN_MODE, 0xff30); + /* auto MDIX, PVID=1, untag */ + ifx_sw_write(ADM_SW_PORT0_CONF, 0x840f); + ifx_sw_write(ADM_SW_PORT1_CONF, 0x840f); + ifx_sw_write(ADM_SW_PORT2_CONF, 0x840f); + ifx_sw_write(ADM_SW_PORT3_CONF, 0x840f); + /* auto MDIX, PVID=2, untag */ + ifx_sw_write(ADM_SW_PORT5_CONF, 0x880f); + /* port 0~3 & 5 as VLAN1 */ + ifx_sw_write(ADM_SW_VLAN0_CONF+1, 0x0155); + + return 0; +} +#endif +/* 509201:linmars end */ + +int adm_open(struct inode *node, struct file *filp) +{ + return 0; +} + +ssize_t adm_read(struct file *filep, char *buf, size_t count, loff_t *ppos) +{ + return count; +} + +ssize_t adm_write(struct file *filep, const char *buf, size_t count, loff_t *ppos) +{ + return count; +} + +/* close */ +int adm_release(struct inode *inode, struct file *filp) +{ + return 0; +} + +/* IOCTL function */ +int adm_ioctl(struct inode *inode, struct file *filp, unsigned int cmd, unsigned long args) +{ + PREGRW uREGRW; + unsigned int rtval; + unsigned int val; //6996i + unsigned int control[6] ; //6996i + unsigned int status[6] ; //6996i + + PMACENTRY mMACENTRY;//adm6996i + PPROTOCOLFILTER uPROTOCOLFILTER ;///adm6996i + + if (_IOC_TYPE(cmd) != ADM_MAGIC) + { + printk("adm_ioctl: IOC_TYPE(%x) != ADM_MAGIC(%x)! \n", _IOC_TYPE(cmd), ADM_MAGIC); + return (-EINVAL); + } + + if(_IOC_NR(cmd) >= KEY_IOCTL_MAX_KEY) + { + printk(KERN_WARNING "adm_ioctl: IOC_NR(%x) invalid! \n", _IOC_NR(cmd)); + return (-EINVAL); + } + + switch (cmd) + { + case ADM_IOCTL_REGRW: + { + uREGRW = (PREGRW)kmalloc(sizeof(REGRW), GFP_KERNEL); + rtval = copy_from_user(uREGRW, (PREGRW)args, sizeof(REGRW)); + if (rtval != 0) + { + printk("ADM_IOCTL_REGRW: copy from user FAILED!! \n"); + return (-EFAULT); + } + + switch(uREGRW->mode) + { + case REG_READ: + uREGRW->value = 0x12345678;//inl(uREGRW->addr); + copy_to_user((PREGRW)args, uREGRW, sizeof(REGRW)); + break; + case REG_WRITE: + //outl(uREGRW->value, uREGRW->addr); + break; + + default: + printk("No such Register Read/Write function!! \n"); + return (-EFAULT); + } + kfree(uREGRW); + break; + } + + case ADM_SW_IOCTL_REGRW: + { + unsigned int val = 0xff; + + uREGRW = (PREGRW)kmalloc(sizeof(REGRW), GFP_KERNEL); + rtval = copy_from_user(uREGRW, (PREGRW)args, sizeof(REGRW)); + if (rtval != 0) + { + printk("ADM_IOCTL_REGRW: copy from user FAILED!! \n"); + return (-EFAULT); + } + + switch(uREGRW->mode) + { + case REG_READ: + ifx_sw_read(uREGRW->addr, &val); + uREGRW->value = val; + copy_to_user((PREGRW)args, uREGRW, sizeof(REGRW)); + break; + + case REG_WRITE: + ifx_sw_write(uREGRW->addr, uREGRW->value); + break; + default: + printk("No such Register Read/Write function!! \n"); + return (-EFAULT); + } + kfree(uREGRW); + break; + } +/* 509201:linmars start */ +#if 0 + case ADM_SW_IOCTL_PORTSTS: + for (rtval = 0; rtval < ADM_SW_MAX_PORT_NUM+1; rtval++) + ifx_check_port_status(rtval); + break; + case ADM_SW_IOCTL_INIT: + ifx_sw_init(); + break; +#endif +/* 509201:linmars end */ +//adm6996i + case ADM_SW_IOCTL_MACENTRY_ADD: + case ADM_SW_IOCTL_MACENTRY_DEL: + case ADM_SW_IOCTL_MACENTRY_GET_INIT: + case ADM_SW_IOCTL_MACENTRY_GET_MORE: + + + mMACENTRY = (PMACENTRY)kmalloc(sizeof(MACENTRY), GFP_KERNEL); + rtval = copy_from_user(mMACENTRY, (PMACENTRY)args, sizeof(MACENTRY)); + if (rtval != 0) + { + printk("ADM_SW_IOCTL_MACENTRY: copy from user FAILED!! \n"); + return (-EFAULT); + } + control[0]=(mMACENTRY->mac_addr[1]<<8)+mMACENTRY->mac_addr[0] ; + control[1]=(mMACENTRY->mac_addr[3]<<8)+mMACENTRY->mac_addr[2] ; + control[2]=(mMACENTRY->mac_addr[5]<<8)+mMACENTRY->mac_addr[4] ; + control[3]=(mMACENTRY->fid&0xf)+((mMACENTRY->portmap&0x3f)<<4); + if (((mMACENTRY->info_type)&0x01)) control[4]=(mMACENTRY->ctrl.info_ctrl)+0x1000; //static ,info control + else control[4]=((mMACENTRY->ctrl.age_timer)&0xff);//not static ,agetimer + if (cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT) { + //initial the pointer to the first address + val=0x8000;//busy ,status5[15] + while(val&0x8000){ //check busy ? + ifx_sw_read(0x125, &val); + } + control[5]=0x030;//initial the first address + ifx_sw_write(0x11f,control[5]); + + + val=0x8000;//busy ,status5[15] + while(val&0x8000){ //check busy ? + ifx_sw_read(0x125, &val); + } + + } //if (cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT) + if (cmd==ADM_SW_IOCTL_MACENTRY_ADD) control[5]=0x07;//create a new address + else if (cmd==ADM_SW_IOCTL_MACENTRY_DEL) control[5]=0x01f;//erased an existed address + else if ((cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT)||(cmd==ADM_SW_IOCTL_MACENTRY_GET_MORE)) + control[5]=0x02c;//search by the mac address field + + val=0x8000;//busy ,status5[15] + while(val&0x8000){ //check busy ? + ifx_sw_read(0x125, &val); + } + ifx_sw_write(0x11a,control[0]); + ifx_sw_write(0x11b,control[1]); + ifx_sw_write(0x11c,control[2]); + ifx_sw_write(0x11d,control[3]); + ifx_sw_write(0x11e,control[4]); + ifx_sw_write(0x11f,control[5]); + val=0x8000;//busy ,status5[15] + while(val&0x8000){ //check busy ? + ifx_sw_read(0x125, &val); + } + val=((val&0x7000)>>12);//result ,status5[14:12] + mMACENTRY->result=val; + + if (!val) { + printk(" Command OK!! \n"); + if ((cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT)||(cmd==ADM_SW_IOCTL_MACENTRY_GET_MORE)) { + ifx_sw_read(0x120,&(status[0])); + ifx_sw_read(0x121,&(status[1])); + ifx_sw_read(0x122,&(status[2])); + ifx_sw_read(0x123,&(status[3])); + ifx_sw_read(0x124,&(status[4])); + ifx_sw_read(0x125,&(status[5])); + + + mMACENTRY->mac_addr[0]=(status[0]&0x00ff) ; + mMACENTRY->mac_addr[1]=(status[0]&0xff00)>>8 ; + mMACENTRY->mac_addr[2]=(status[1]&0x00ff) ; + mMACENTRY->mac_addr[3]=(status[1]&0xff00)>>8 ; + mMACENTRY->mac_addr[4]=(status[2]&0x00ff) ; + mMACENTRY->mac_addr[5]=(status[2]&0xff00)>>8 ; + mMACENTRY->fid=(status[3]&0xf); + mMACENTRY->portmap=((status[3]>>4)&0x3f); + if (status[5]&0x2) {//static info_ctrl //status5[1]???? + mMACENTRY->ctrl.info_ctrl=(status[4]&0x00ff); + mMACENTRY->info_type=1; + } + else {//not static age_timer + mMACENTRY->ctrl.age_timer=(status[4]&0x00ff); + mMACENTRY->info_type=0; + } +//status5[13]???? mMACENTRY->occupy=(status[5]&0x02)>>1;//status5[1] + mMACENTRY->occupy=(status[5]&0x02000)>>13;//status5[13] ??? + mMACENTRY->bad=(status[5]&0x04)>>2;//status5[2] + }//if ((cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT)||(cmd==ADM_SW_IOCTL_MACENTRY_GET_MORE)) + + } + else if (val==0x001) + printk(" All Entry Used!! \n"); + else if (val==0x002) + printk(" Entry Not Found!! \n"); + else if (val==0x003) + printk(" Try Next Entry!! \n"); + else if (val==0x005) + printk(" Command Error!! \n"); + else + printk(" UnKnown Error!! \n"); + + copy_to_user((PMACENTRY)args, mMACENTRY,sizeof(MACENTRY)); + + break; + + case ADM_SW_IOCTL_FILTER_ADD: + case ADM_SW_IOCTL_FILTER_DEL: + case ADM_SW_IOCTL_FILTER_GET: + + uPROTOCOLFILTER = (PPROTOCOLFILTER)kmalloc(sizeof(PROTOCOLFILTER), GFP_KERNEL); + rtval = copy_from_user(uPROTOCOLFILTER, (PPROTOCOLFILTER)args, sizeof(PROTOCOLFILTER)); + if (rtval != 0) + { + printk("ADM_SW_IOCTL_FILTER_ADD: copy from user FAILED!! \n"); + return (-EFAULT); + } + + if(cmd==ADM_SW_IOCTL_FILTER_DEL) { //delete filter + uPROTOCOLFILTER->ip_p=00; //delet filter + uPROTOCOLFILTER->action=00; //delete filter + } //delete filter + + ifx_sw_read(((uPROTOCOLFILTER->protocol_filter_num/2)+0x68), &val);//rx68~rx6b,protocol filter0~7 + + if (((uPROTOCOLFILTER->protocol_filter_num)%2)==00){ + if(cmd==ADM_SW_IOCTL_FILTER_GET) uPROTOCOLFILTER->ip_p= val&0x00ff;//get filter ip_p + else val=(val&0xff00)|(uPROTOCOLFILTER->ip_p);//set filter ip_p + } + else { + if(cmd==ADM_SW_IOCTL_FILTER_GET) uPROTOCOLFILTER->ip_p= (val>>8);//get filter ip_p + else val=(val&0x00ff)|((uPROTOCOLFILTER->ip_p)<<8);//set filter ip_p + } + if(cmd!=ADM_SW_IOCTL_FILTER_GET) ifx_sw_write(((uPROTOCOLFILTER->protocol_filter_num/2)+0x68), val);//write rx68~rx6b,protocol filter0~7 + + ifx_sw_read(0x95, &val); //protocol filter action + if(cmd==ADM_SW_IOCTL_FILTER_GET) { + uPROTOCOLFILTER->action= ((val>>(uPROTOCOLFILTER->protocol_filter_num*2))&0x3);//get filter action + copy_to_user((PPROTOCOLFILTER)args, uPROTOCOLFILTER, sizeof(PROTOCOLFILTER)); + + } + else { + val=(val&(~(0x03<<(uPROTOCOLFILTER->protocol_filter_num*2))))|(((uPROTOCOLFILTER->action)&0x03)<<(uPROTOCOLFILTER->protocol_filter_num*2)); + // printk("%d----\n",val); + ifx_sw_write(0x95, val); //write protocol filter action + } + + break; +//adm6996i + + /* others */ + default: + return -EFAULT; + } + /* end of switch */ + return 0; +} + +/* Santosh: handle IGMP protocol filter ADD/DEL/GET */ +int adm_process_protocol_filter_request (unsigned int cmd, PPROTOCOLFILTER uPROTOCOLFILTER) +{ + unsigned int val; //6996i + + if(cmd==ADM_SW_IOCTL_FILTER_DEL) { //delete filter + uPROTOCOLFILTER->ip_p=00; //delet filter + uPROTOCOLFILTER->action=00; //delete filter + } //delete filter + + ifx_sw_read(((uPROTOCOLFILTER->protocol_filter_num/2)+0x68), &val);//rx68~rx6b,protocol filter0~7 + + if (((uPROTOCOLFILTER->protocol_filter_num)%2)==00){ + if(cmd==ADM_SW_IOCTL_FILTER_GET) uPROTOCOLFILTER->ip_p= val&0x00ff;//get filter ip_p + else val=(val&0xff00)|(uPROTOCOLFILTER->ip_p);//set filter ip_p + } + else { + if(cmd==ADM_SW_IOCTL_FILTER_GET) uPROTOCOLFILTER->ip_p= (val>>8);//get filter ip_p + else val=(val&0x00ff)|((uPROTOCOLFILTER->ip_p)<<8);//set filter ip_p + } + if(cmd!=ADM_SW_IOCTL_FILTER_GET) ifx_sw_write(((uPROTOCOLFILTER->protocol_filter_num/2)+0x68), val);//write rx68~rx6b,protocol filter0~7 + + ifx_sw_read(0x95, &val); //protocol filter action + if(cmd==ADM_SW_IOCTL_FILTER_GET) { + uPROTOCOLFILTER->action= ((val>>(uPROTOCOLFILTER->protocol_filter_num*2))&0x3);//get filter action + } + else { + val=(val&(~(0x03<<(uPROTOCOLFILTER->protocol_filter_num*2))))|(((uPROTOCOLFILTER->action)&0x03)<<(uPROTOCOLFILTER->protocol_filter_num*2)); + ifx_sw_write(0x95, val); //write protocol filter action + } + + return 0; +} + + +/* Santosh: function for MAC ENTRY ADD/DEL/GET */ + +int adm_process_mac_table_request (unsigned int cmd, PMACENTRY mMACENTRY) +{ + unsigned int rtval; + unsigned int val; //6996i + unsigned int control[6] ; //6996i + unsigned int status[6] ; //6996i + + // printk ("adm_process_mac_table_request: enter\n"); + + control[0]=(mMACENTRY->mac_addr[1]<<8)+mMACENTRY->mac_addr[0] ; + control[1]=(mMACENTRY->mac_addr[3]<<8)+mMACENTRY->mac_addr[2] ; + control[2]=(mMACENTRY->mac_addr[5]<<8)+mMACENTRY->mac_addr[4] ; + control[3]=(mMACENTRY->fid&0xf)+((mMACENTRY->portmap&0x3f)<<4); + + if (((mMACENTRY->info_type)&0x01)) control[4]=(mMACENTRY->ctrl.info_ctrl)+0x1000; //static ,info control + else control[4]=((mMACENTRY->ctrl.age_timer)&0xff);//not static ,agetimer + if (cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT) { + //initial the pointer to the first address + val=0x8000;//busy ,status5[15] + while(val&0x8000){ //check busy ? + ifx_sw_read(0x125, &val); + } + control[5]=0x030;//initial the first address + ifx_sw_write(0x11f,control[5]); + + + val=0x8000;//busy ,status5[15] + while(val&0x8000){ //check busy ? + ifx_sw_read(0x125, &val); + } + + } //if (cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT) + if (cmd==ADM_SW_IOCTL_MACENTRY_ADD) control[5]=0x07;//create a new address + else if (cmd==ADM_SW_IOCTL_MACENTRY_DEL) control[5]=0x01f;//erased an existed address + else if ((cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT)||(cmd==ADM_SW_IOCTL_MACENTRY_GET_MORE)) + control[5]=0x02c;//search by the mac address field + + val=0x8000;//busy ,status5[15] + while(val&0x8000){ //check busy ? + ifx_sw_read(0x125, &val); + } + ifx_sw_write(0x11a,control[0]); + ifx_sw_write(0x11b,control[1]); + ifx_sw_write(0x11c,control[2]); + ifx_sw_write(0x11d,control[3]); + ifx_sw_write(0x11e,control[4]); + ifx_sw_write(0x11f,control[5]); + val=0x8000;//busy ,status5[15] + while(val&0x8000){ //check busy ? + ifx_sw_read(0x125, &val); + } + val=((val&0x7000)>>12);//result ,status5[14:12] + mMACENTRY->result=val; + + if (!val) { + printk(" Command OK!! \n"); + if ((cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT)||(cmd==ADM_SW_IOCTL_MACENTRY_GET_MORE)) { + ifx_sw_read(0x120,&(status[0])); + ifx_sw_read(0x121,&(status[1])); + ifx_sw_read(0x122,&(status[2])); + ifx_sw_read(0x123,&(status[3])); + ifx_sw_read(0x124,&(status[4])); + ifx_sw_read(0x125,&(status[5])); + + + mMACENTRY->mac_addr[0]=(status[0]&0x00ff) ; + mMACENTRY->mac_addr[1]=(status[0]&0xff00)>>8 ; + mMACENTRY->mac_addr[2]=(status[1]&0x00ff) ; + mMACENTRY->mac_addr[3]=(status[1]&0xff00)>>8 ; + mMACENTRY->mac_addr[4]=(status[2]&0x00ff) ; + mMACENTRY->mac_addr[5]=(status[2]&0xff00)>>8 ; + mMACENTRY->fid=(status[3]&0xf); + mMACENTRY->portmap=((status[3]>>4)&0x3f); + if (status[5]&0x2) {//static info_ctrl //status5[1]???? + mMACENTRY->ctrl.info_ctrl=(status[4]&0x00ff); + mMACENTRY->info_type=1; + } + else {//not static age_timer + mMACENTRY->ctrl.age_timer=(status[4]&0x00ff); + mMACENTRY->info_type=0; + } +//status5[13]???? mMACENTRY->occupy=(status[5]&0x02)>>1;//status5[1] + mMACENTRY->occupy=(status[5]&0x02000)>>13;//status5[13] ??? + mMACENTRY->bad=(status[5]&0x04)>>2;//status5[2] + }//if ((cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT)||(cmd==ADM_SW_IOCTL_MACENTRY_GET_MORE)) + + } + else if (val==0x001) + printk(" All Entry Used!! \n"); + else if (val==0x002) + printk(" Entry Not Found!! \n"); + else if (val==0x003) + printk(" Try Next Entry!! \n"); + else if (val==0x005) + printk(" Command Error!! \n"); + else + printk(" UnKnown Error!! \n"); + + // printk ("adm_process_mac_table_request: Exit\n"); + return 0; +} + +/* Santosh: End of function for MAC ENTRY ADD/DEL*/ +struct file_operations adm_ops = +{ + read: adm_read, + write: adm_write, + open: adm_open, + release: adm_release, + ioctl: adm_ioctl +}; + +int adm_proc(char *buf, char **start, off_t offset, int count, int *eof, void *data) +{ + int len = 0; + + len += sprintf(buf+len, " ************ Registers ************ \n"); + *eof = 1; + return len; +} + +int __init init_adm6996_module(void) +{ + unsigned int val = 000; + unsigned int val1 = 000; + + printk("Loading ADM6996 driver... \n"); + + /* if running on adm5120 */ + /* set GPIO 0~2 as adm6996 control pins */ + //outl(0x003f3f00, 0x12000028); + /* enable switch port 5 (MII) as RMII mode (5120MAC <-> 6996MAC) */ + //outl(0x18a, 0x12000030); + /* group adm5120 port 1 ~ 5 as VLAN0, port 5 & 6(CPU) as VLAN1 */ + //outl(0x417e, 0x12000040); + /* end adm5120 fixup */ +#ifdef ADM6996_MDC_MDIO_MODE //smi mode //000001.joelin + register_chrdev(69, "adm6996", &adm_ops); + AMAZON_SW_REG(AMAZON_SW_MDIO_CFG) = 0x27be; + AMAZON_SW_REG(AMAZON_SW_EPHY) = 0xfc; + adm6996_mode=adm6996i; + ifx_sw_read(0xa0, &val); + ifx_sw_read(0xa1, &val1); + val=((val1&0x0f)<<16)|val; + printk ("\nADM6996 SMI Mode-"); + printk ("Chip ID:%5x \n ", val); +#else //000001.joelin + + AMAZON_SW_REG(AMAZON_SW_MDIO_CFG) = 0x2c50; + AMAZON_SW_REG(AMAZON_SW_EPHY) = 0xff; + + AMAZON_SW_REG(AMAZON_GPIO_P1_ALTSEL0) &= ~(GPIO_MDIO|GPIO_MDCS|GPIO_MDC); + AMAZON_SW_REG(AMAZON_GPIO_P1_ALTSEL1) &= ~(GPIO_MDIO|GPIO_MDCS|GPIO_MDC); + AMAZON_SW_REG(AMAZON_GPIO_P1_OD) |= (GPIO_MDIO|GPIO_MDCS|GPIO_MDC); + + ifx_gpio_init(); + register_chrdev(69, "adm6996", &adm_ops); + mdelay(100); + + /* create proc entries */ + // create_proc_read_entry("admide", 0, NULL, admide_proc, NULL); + +//joelin adm6996i support start + adm6996_mode=adm6996i; + ifx_sw_read(0xa0, &val); + adm6996_mode=adm6996l; + ifx_sw_read(0x200, &val1); +// printk ("\n %0x \n",val1); + if ((val&0xfff0)==0x1020) { + printk ("\n ADM6996I .. \n"); + adm6996_mode=adm6996i; + } + else if ((val1&0xffffff00)==0x71000) {//71010 or 71020 + printk ("\n ADM6996LC .. \n"); + adm6996_mode=adm6996lc; + } + else { + printk ("\n ADM6996L .. \n"); + adm6996_mode=adm6996l; + } +#endif //ADM6996_MDC_MDIO_MODE //smi mode //000001.joelin + + if ((adm6996_mode==adm6996lc)||(adm6996_mode==adm6996i)){ +#if 0 /* removed by MarsLin */ + ifx_sw_write(0x29,0xc000); + ifx_sw_write(0x30,0x0985); +#else + ifx_sw_read(0xa0, &val); + if (val == 0x1021) // for both 6996LC and 6996I, only AB version need the patch + ifx_sw_write(0x29, 0x9000); + ifx_sw_write(0x30,0x0985); +#endif + } +//joelin adm6996i support end + return 0; +} + +void __exit cleanup_adm6996_module(void) +{ + printk("Free ADM device driver... \n"); + + unregister_chrdev(69, "adm6996"); + + /* remove proc entries */ + // remove_proc_entry("admide", NULL); +} + +/* MarsLin, add start */ +#if defined(CONFIG_IFX_NFEXT_AMAZON_SWITCH_PHYPORT) || defined(CONFIG_IFX_NFEXT_AMAZON_SWITCH_PHYPORT_MODULE) + #define SET_BIT(reg, mask) reg |= (mask) + #define CLEAR_BIT(reg, mask) reg &= (~mask) + static int ifx_hw_reset(void) + { + CLEAR_BIT((*AMAZON_GPIO_P0_ALTSEL0),0x2000); + CLEAR_BIT((*AMAZON_GPIO_P0_ALTSEL1),0x2000); + SET_BIT((*AMAZON_GPIO_P0_OD),0x2000); + SET_BIT((*AMAZON_GPIO_P0_DIR), 0x2000); + CLEAR_BIT((*AMAZON_GPIO_P0_OUT), 0x2000); + mdelay(500); + SET_BIT((*AMAZON_GPIO_P0_OUT), 0x2000); + cleanup_adm6996_module(); + return init_adm6996_module(); + } + int (*adm6996_hw_reset)(void) = ifx_hw_reset; + EXPORT_SYMBOL(adm6996_hw_reset); + EXPORT_SYMBOL(adm6996_mode); + int (*adm6996_sw_read)(unsigned int addr, unsigned int *data) = ifx_sw_read; + EXPORT_SYMBOL(adm6996_sw_read); + int (*adm6996_sw_write)(unsigned int addr, unsigned int data) = ifx_sw_write; + EXPORT_SYMBOL(adm6996_sw_write); +#endif +/* MarsLin, add end */ + +/* Santosh: for IGMP proxy/snooping, Begin */ +EXPORT_SYMBOL (adm_process_mac_table_request); +EXPORT_SYMBOL (adm_process_protocol_filter_request); +/* Santosh: for IGMP proxy/snooping, End */ + +MODULE_DESCRIPTION("ADMtek 6996 Driver"); +MODULE_AUTHOR("Joe Lin "); +MODULE_LICENSE("GPL"); + +module_init(init_adm6996_module); +module_exit(cleanup_adm6996_module); + diff --git a/target/linux/amazon/patches/110-char_drivers.patch b/target/linux/amazon/patches/110-char_drivers.patch deleted file mode 100644 index f56f8969f5..0000000000 --- a/target/linux/amazon/patches/110-char_drivers.patch +++ /dev/null @@ -1,10 +0,0 @@ ---- a/drivers/char/Makefile -+++ b/drivers/char/Makefile -@@ -104,6 +104,7 @@ obj-$(CONFIG_IPMI_HANDLER) += ipmi/ - - obj-$(CONFIG_HANGCHECK_TIMER) += hangcheck-timer.o - obj-$(CONFIG_TCG_TPM) += tpm/ -+obj-$(CONFIG_AMAZONE_WDT) += amazone_wdt.o - - # Files generated that shall be removed upon make clean - clean-files := consolemap_deftbl.c defkeymap.c diff --git a/target/linux/amazon/patches/140-net_drivers.patch b/target/linux/amazon/patches/140-net_drivers.patch index 4732250e12..2b5c1b6324 100644 --- a/target/linux/amazon/patches/140-net_drivers.patch +++ b/target/linux/amazon/patches/140-net_drivers.patch @@ -1,8 +1,9 @@ --- a/drivers/net/Makefile +++ b/drivers/net/Makefile -@@ -219,3 +219,5 @@ obj-$(CONFIG_NETCONSOLE) += netconsole.o +@@ -219,3 +219,6 @@ obj-$(CONFIG_NETCONSOLE) += netconsole.o obj-$(CONFIG_FS_ENET) += fs_enet/ obj-$(CONFIG_NETXEN_NIC) += netxen/ + +obj-$(CONFIG_AMAZON_NET_SW) += amazon_sw.o ++obj-$(CONFIG_ADM6996_SUPPORT) += admmod.o