From: Pavel Chervontsev Date: Mon, 2 Nov 2020 11:50:01 +0000 (+0300) Subject: ramips: add support for ASUS RT-N56U B1 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=6d98c098e48414b0da8aa6c25aa9044a201c1ba6;p=openwrt%2Fstaging%2Fblocktrron.git ramips: add support for ASUS RT-N56U B1 Specifications: SoC: MediaTek MT7621ST (880 MHz) FLASH: 16 MiB (Macronix MX25L12835FM2I-10G) RAM: 128 MiB (Nanya NT5CB64M16FP-DH) WiFi: MediaTek MT7603EN bgn 2x2:2 WiFi: MediaTek MT7612EN an 2x2:2 BTN: Reset, WPS LED: - Power - WiFi 2.4 GHz - WiFi 5 GHz - WAN - LAN {1-4} - USB {1-2} UART: UART is present as pin hole next to the aluminium capacitor. 3V3 - RX - GND - TX / 115200-8N1 3V3 is the nearest on the aluminium capacitor and nut hole (pin1). USB: 2 ports POWER: 12VDC, 1.5A (Barrel 5.5x2.1) Installation: Via TFTP: Set your computers IP-Address to 192.168.1.75 Power up the Router with the Reset button pressed. Release the Reset button after 5 seconds. Upload OpenWRT sysupgrade image via TFTP: tftp -4 -v -m binary 192.168.1.1 -c put IMAGE MAC addresses: 0x4 *:98 2g/wan, label 0x22 *:9c 0x28 *:98 0x8004 *:9c 5g/lan Though addresses are written to 0x22 and 0x28, it appears that the vendor firmware actually only uses 0x4 and 0x8004. Thus, we do the same here. Signed-off-by: Pavel Chervontsev [add MAC address overview, add label-mac-device, fix IMAGE_SIZE] Signed-off-by: Adrian Schmutzler --- diff --git a/target/linux/ramips/dts/mt7621_asus_rt-n56u-b1.dts b/target/linux/ramips/dts/mt7621_asus_rt-n56u-b1.dts new file mode 100644 index 0000000000..b78e594ffd --- /dev/null +++ b/target/linux/ramips/dts/mt7621_asus_rt-n56u-b1.dts @@ -0,0 +1,181 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "mt7621.dtsi" + +#include +#include + +/ { + compatible = "asus,rt-n56u-b1", "mediatek,mt7621-soc"; + model = "ASUS RT-N56U B1"; + + aliases { + label-mac-device = &wan; + led-boot = &led_power; + led-failsafe = &led_power; + led-running = &led_power; + led-upgrade = &led_power; + }; + + chosen { + bootargs = "console=ttyS0,115200"; + }; + + leds { + compatible = "gpio-leds"; + + led_power: power { + label = "blue:power"; + gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + }; + + wlan2g { + label = "blue:wlan2g"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + wlan5g { + label = "blue:wlan5g"; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + + wan { + label = "blue:wan"; + gpios = <&gpio 7 GPIO_ACTIVE_LOW>; + }; + + lan { + label = "blue:lan"; + gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + }; + + usb { + label = "blue:usb"; + gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + trigger-sources = <&xhci_ehci_port1>, <&ehci_port2>; + linux,default-trigger = "usbport"; + }; + }; + + keys { + compatible = "gpio-keys"; + + wps { + label = "wps"; + gpios = <&gpio 18 GPIO_ACTIVE_HIGH>; + linux,code = ; + debounce-interval = <60>; + }; + + reset { + label = "reset"; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <60>; + }; + }; +}; + +&spi0 { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <50000000>; + m25p,fast-read; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x30000>; + read-only; + }; + + partition@30000 { + label = "config"; + reg = <0x30000 0x10000>; + read-only; + }; + + factory: partition@40000 { + label = "factory"; + reg = <0x40000 0x10000>; + read-only; + }; + + partition@50000 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0x50000 0xfb0000>; + }; + }; + }; +}; + +&pcie { + status = "okay"; +}; + +&pcie0 { + wifi@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0000 0 0 0 0>; + mediatek,mtd-eeprom = <&factory 0x8000>; + }; +}; + +&pcie1 { + wifi@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0000 0 0 0 0>; + mediatek,mtd-eeprom = <&factory 0x0000>; + }; +}; + +&gmac0 { + mtd-mac-address = <&factory 0x8004>; +}; + +&switch0 { + ports { + port@0 { + status = "okay"; + label = "lan4"; + }; + + port@1 { + status = "okay"; + label = "lan3"; + }; + + port@2 { + status = "okay"; + label = "lan2"; + }; + + port@3 { + status = "okay"; + label = "lan1"; + }; + + wan: port@4 { + status = "okay"; + label = "wan"; + mtd-mac-address = <&factory 0x4>; + }; + }; +}; + +&state_default { + gpio { + groups = "uart3", "uart2", "jtag", "wdt"; + function = "gpio"; + }; +}; diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk index ce9a3ae3d2..7b8a73c1bd 100644 --- a/target/linux/ramips/image/mt7621.mk +++ b/target/linux/ramips/image/mt7621.mk @@ -188,6 +188,17 @@ define Device/asus_rt-ac85p endef TARGET_DEVICES += asus_rt-ac85p +define Device/asus_rt-n56u-b1 + $(Device/dsa-migration) + DEVICE_VENDOR := ASUS + DEVICE_MODEL := RT-N56U + DEVICE_VARIANT := B1 + IMAGE_SIZE := 16064k + DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \ + kmod-usb-ledtrig-usbport +endef +TARGET_DEVICES += asus_rt-n56u-b1 + define Device/buffalo_wsr-1166dhp $(Device/dsa-migration) $(Device/uimage-lzma-loader) diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds b/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds index 3dd2a218b9..cd1814cc2b 100755 --- a/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds @@ -8,6 +8,10 @@ board=$(board_name) board_config_update case $board in +asus,rt-n56u-b1) + ucidef_set_led_netdev "lan" "LAN link" "blue:lan" "br-lan" + ucidef_set_led_netdev "wan" "WAN link" "blue:wan" "wan" + ;; d-team,newifi-d2) ucidef_set_led_netdev "internet" "internet" "amber:internet" "wan" ucidef_set_led_netdev "wlan2g" "WiFi 2.4GHz" "blue:wlan2g" "wlan0"