From: Adrian Schmutzler Date: Tue, 8 Dec 2020 14:05:47 +0000 (+0100) Subject: ramips: use full names for Xiaomi Mi Router devices X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=6d4382711a65b5606cc9b815e6590b0e36ebf5b5;p=openwrt%2Fstaging%2Fthess.git ramips: use full names for Xiaomi Mi Router devices This aligns the device/image names of the older Xiaomi Mi Router devices with their "friendly" model and DEVICE_MODEL properties. This also reintroduces consistency with the newer devices already following that scheme. Signed-off-by: Adrian Schmutzler --- diff --git a/target/linux/ramips/dts/mt7621_xiaomi_mi-router-3-pro.dts b/target/linux/ramips/dts/mt7621_xiaomi_mi-router-3-pro.dts new file mode 100644 index 0000000000..b9101b7ccb --- /dev/null +++ b/target/linux/ramips/dts/mt7621_xiaomi_mi-router-3-pro.dts @@ -0,0 +1,212 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "mt7621.dtsi" + +#include +#include + +/ { + compatible = "xiaomi,mi-router-3-pro", "mediatek,mt7621-soc"; + model = "Xiaomi Mi Router 3 Pro"; + + aliases { + led-boot = &led_status_yellow; + led-failsafe = &led_status_red; + led-running = &led_status_blue; + led-upgrade = &led_status_yellow; + label-mac-device = &gmac0; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + leds { + compatible = "gpio-leds"; + + led_status_red: status_red { + label = "red:status"; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + }; + + led_status_blue: status_blue { + label = "blue:status"; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + }; + + led_status_yellow: status_yellow { + label = "yellow:status"; + gpios = <&gpio 10 GPIO_ACTIVE_LOW>; + }; + + wan_amber { + label = "amber:wan"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + linux,default-trigger = "dsa-0.0:04:1Gbps"; + }; + + lan3_amber { + label = "amber:lan3"; + gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + linux,default-trigger = "dsa-0.0:01:1Gbps"; + }; + + lan2_amber { + label = "amber:lan2"; + gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + linux,default-trigger = "dsa-0.0:02:1Gbps"; + }; + + lan1_amber { + label = "amber:lan1"; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + linux,default-trigger = "dsa-0.0:03:1Gbps"; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&gpio 18 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + reg_usb_vbus: regulator { + compatible = "regulator-fixed"; + regulator-name = "usb_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio 12 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&xhci { + vbus-supply = <®_usb_vbus>; +}; + +&nand { + status = "okay"; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "Bootloader"; + reg = <0x0 0x40000>; + read-only; + }; + + partition@40000 { + label = "Config"; + reg = <0x40000 0x40000>; + }; + + partition@80000 { + label = "Bdata"; + reg = <0x80000 0x40000>; + read-only; + }; + + factory: partition@c0000 { + label = "factory"; + reg = <0x0c0000 0x40000>; + read-only; + }; + + partition@100000 { + label = "crash"; + reg = <0x100000 0x40000>; + }; + + partition@140000 { + label = "crash_syslog"; + reg = <0x140000 0x80000>; + }; + + partition@1c0000 { + label = "reserved0"; + reg = <0x1c0000 0x40000>; + read-only; + }; + + /* We keep stock xiaomi firmware (kernel0) here */ + partition@200000 { + label = "kernel_stock"; + reg = <0x200000 0x400000>; + }; + + partition@600000 { + label = "kernel"; + reg = <0x600000 0x400000>; + }; + + partition@a00000 { + label = "ubi"; + reg = <0xa00000 0xf580000>; + }; + }; +}; + +&pcie { + status = "okay"; +}; + +&pcie0 { + wifi@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0000 0 0 0 0>; + mediatek,mtd-eeprom = <&factory 0x0000>; + ieee80211-freq-limit = <2400000 2500000>; + }; +}; + +&pcie1 { + wifi@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0000 0 0 0 0>; + mediatek,mtd-eeprom = <&factory 0x8000>; + ieee80211-freq-limit = <5000000 6000000>; + }; +}; + +&gmac0 { + mtd-mac-address = <&factory 0xe006>; +}; + +&switch0 { + ports { + port@1 { + status = "okay"; + label = "lan3"; + }; + + port@2 { + status = "okay"; + label = "lan2"; + }; + + port@3 { + status = "okay"; + label = "lan1"; + }; + + port@4 { + status = "okay"; + label = "wan"; + mtd-mac-address = <&factory 0xe000>; + }; + }; +}; + +&state_default { + gpio { + groups = "jtag", "uart2", "uart3", "wdt"; + function = "gpio"; + }; +}; diff --git a/target/linux/ramips/dts/mt7621_xiaomi_mi-router-3g-v2.dts b/target/linux/ramips/dts/mt7621_xiaomi_mi-router-3g-v2.dts new file mode 100644 index 0000000000..fe03ff1e6a --- /dev/null +++ b/target/linux/ramips/dts/mt7621_xiaomi_mi-router-3g-v2.dts @@ -0,0 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "mt7621_xiaomi_mi-router-4a-3g-v2.dtsi" + +/ { + compatible = "xiaomi,mi-router-3g-v2", "mediatek,mt7621-soc"; + model = "Xiaomi Mi Router 3G v2"; +}; diff --git a/target/linux/ramips/dts/mt7621_xiaomi_mi-router-3g.dts b/target/linux/ramips/dts/mt7621_xiaomi_mi-router-3g.dts new file mode 100644 index 0000000000..479cfc354c --- /dev/null +++ b/target/linux/ramips/dts/mt7621_xiaomi_mi-router-3g.dts @@ -0,0 +1,220 @@ +#include "mt7621.dtsi" + +#include +#include + +/ { + compatible = "xiaomi,mi-router-3g", "mediatek,mt7621-soc"; + model = "Xiaomi Mi Router 3G"; + + aliases { + led-boot = &led_status_yellow; + led-failsafe = &led_status_red; + led-running = &led_status_blue; + led-upgrade = &led_status_yellow; + label-mac-device = &gmac0; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + leds { + compatible = "gpio-leds"; + + led_status_red: status_red { + label = "red:status"; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + }; + + led_status_blue: status_blue { + label = "blue:status"; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + }; + + led_status_yellow: status_yellow { + label = "yellow:status"; + gpios = <&gpio 10 GPIO_ACTIVE_LOW>; + }; + + wan_amber { + label = "amber:wan"; + gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + linux,default-trigger = "dsa-0.0:01:1Gbps"; + }; + + lan1_amber { + label = "amber:lan1"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + linux,default-trigger = "dsa-0.0:03:1Gbps"; + }; + + lan2_amber { + label = "amber:lan2"; + gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + linux,default-trigger = "dsa-0.0:02:1Gbps"; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&gpio 18 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + reg_usb_vbus: regulator { + compatible = "regulator-fixed"; + regulator-name = "usb_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio 12 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&xhci { + vbus-supply = <®_usb_vbus>; +}; + +&nand { + status = "okay"; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "Bootloader"; + reg = <0x0 0x80000>; + read-only; + }; + + partition@80000 { + label = "Config"; + reg = <0x80000 0x40000>; + }; + + partition@c0000 { + label = "Bdata"; + reg = <0xc0000 0x40000>; + read-only; + }; + + factory: partition@100000 { + label = "factory"; + reg = <0x100000 0x40000>; + read-only; + }; + + partition@140000 { + label = "crash"; + reg = <0x140000 0x40000>; + }; + + partition@180000 { + label = "crash_syslog"; + reg = <0x180000 0x40000>; + }; + + partition@1c0000 { + label = "reserved0"; + reg = <0x1c0000 0x40000>; + read-only; + }; + + /* uboot expects to find kernels at 0x200000 & 0x600000 + * referred to as system 1 & system 2 respectively. + * a kernel is considered suitable for handing control over + * if its linux magic number exists & uImage CRC are correct. + * If either of those conditions fail, a matching sys'n'_fail flag + * is set in uboot env & a restart performed in the hope that the + * alternate kernel is okay. + * if neither kernel checksums ok and both are marked failed, system 2 + * is booted anyway. + * + * Note uboot's tftp flash install writes the transferred + * image to both kernel partitions. + */ + + partition@200000 { + label = "kernel_stock"; + reg = <0x200000 0x400000>; + }; + + partition@600000 { + label = "kernel"; + reg = <0x600000 0x400000>; + }; + + /* ubi partition is the result of squashing + * next consecutive stock partitions: + * - rootfs0 (rootfs partition for stock kernel0), + * - rootfs1 (rootfs partition for stock failsafe kernel1), + * - overlay (used as ubi overlay in stock fw) + * resulting 117,5MiB space for packages. + */ + + partition@a00000 { + label = "ubi"; + reg = <0xa00000 0x7580000>; + }; + }; +}; + +&pcie { + status = "okay"; +}; + +&pcie0 { + wifi@0,0 { + compatible = "pci14c3,7603"; + reg = <0x0000 0 0 0 0>; + mediatek,mtd-eeprom = <&factory 0x0000>; + ieee80211-freq-limit = <2400000 2500000>; + }; +}; + +&pcie1 { + wifi@0,0 { + compatible = "pci14c3,7662"; + reg = <0x0000 0 0 0 0>; + mediatek,mtd-eeprom = <&factory 0x8000>; + ieee80211-freq-limit = <5000000 6000000>; + }; +}; + +&gmac0 { + mtd-mac-address = <&factory 0xe006>; +}; + +&switch0 { + ports { + port@1 { + status = "okay"; + label = "wan"; + mtd-mac-address = <&factory 0xe000>; + }; + + port@2 { + status = "okay"; + label = "lan2"; + }; + + port@3 { + status = "okay"; + label = "lan1"; + }; + }; +}; + +&state_default { + gpio { + groups = "jtag", "uart2", "uart3", "wdt"; + function = "gpio"; + }; +}; diff --git a/target/linux/ramips/dts/mt7621_xiaomi_mir3g-v2.dts b/target/linux/ramips/dts/mt7621_xiaomi_mir3g-v2.dts deleted file mode 100644 index 50c5a7dafb..0000000000 --- a/target/linux/ramips/dts/mt7621_xiaomi_mir3g-v2.dts +++ /dev/null @@ -1,8 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later OR MIT - -#include "mt7621_xiaomi_mi-router-4a-3g-v2.dtsi" - -/ { - compatible = "xiaomi,mir3g-v2", "mediatek,mt7621-soc"; - model = "Xiaomi Mi Router 3G v2"; -}; diff --git a/target/linux/ramips/dts/mt7621_xiaomi_mir3g.dts b/target/linux/ramips/dts/mt7621_xiaomi_mir3g.dts deleted file mode 100644 index 51f4842255..0000000000 --- a/target/linux/ramips/dts/mt7621_xiaomi_mir3g.dts +++ /dev/null @@ -1,220 +0,0 @@ -#include "mt7621.dtsi" - -#include -#include - -/ { - compatible = "xiaomi,mir3g", "mediatek,mt7621-soc"; - model = "Xiaomi Mi Router 3G"; - - aliases { - led-boot = &led_status_yellow; - led-failsafe = &led_status_red; - led-running = &led_status_blue; - led-upgrade = &led_status_yellow; - label-mac-device = &gmac0; - }; - - chosen { - bootargs = "console=ttyS0,115200n8"; - }; - - leds { - compatible = "gpio-leds"; - - led_status_red: status_red { - label = "red:status"; - gpios = <&gpio 6 GPIO_ACTIVE_LOW>; - }; - - led_status_blue: status_blue { - label = "blue:status"; - gpios = <&gpio 8 GPIO_ACTIVE_LOW>; - }; - - led_status_yellow: status_yellow { - label = "yellow:status"; - gpios = <&gpio 10 GPIO_ACTIVE_LOW>; - }; - - wan_amber { - label = "amber:wan"; - gpios = <&gpio 13 GPIO_ACTIVE_LOW>; - linux,default-trigger = "dsa-0.0:01:1Gbps"; - }; - - lan1_amber { - label = "amber:lan1"; - gpios = <&gpio 14 GPIO_ACTIVE_LOW>; - linux,default-trigger = "dsa-0.0:03:1Gbps"; - }; - - lan2_amber { - label = "amber:lan2"; - gpios = <&gpio 16 GPIO_ACTIVE_LOW>; - linux,default-trigger = "dsa-0.0:02:1Gbps"; - }; - }; - - keys { - compatible = "gpio-keys"; - - reset { - label = "reset"; - gpios = <&gpio 18 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - reg_usb_vbus: regulator { - compatible = "regulator-fixed"; - regulator-name = "usb_vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - gpio = <&gpio 12 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; -}; - -&xhci { - vbus-supply = <®_usb_vbus>; -}; - -&nand { - status = "okay"; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "Bootloader"; - reg = <0x0 0x80000>; - read-only; - }; - - partition@80000 { - label = "Config"; - reg = <0x80000 0x40000>; - }; - - partition@c0000 { - label = "Bdata"; - reg = <0xc0000 0x40000>; - read-only; - }; - - factory: partition@100000 { - label = "factory"; - reg = <0x100000 0x40000>; - read-only; - }; - - partition@140000 { - label = "crash"; - reg = <0x140000 0x40000>; - }; - - partition@180000 { - label = "crash_syslog"; - reg = <0x180000 0x40000>; - }; - - partition@1c0000 { - label = "reserved0"; - reg = <0x1c0000 0x40000>; - read-only; - }; - - /* uboot expects to find kernels at 0x200000 & 0x600000 - * referred to as system 1 & system 2 respectively. - * a kernel is considered suitable for handing control over - * if its linux magic number exists & uImage CRC are correct. - * If either of those conditions fail, a matching sys'n'_fail flag - * is set in uboot env & a restart performed in the hope that the - * alternate kernel is okay. - * if neither kernel checksums ok and both are marked failed, system 2 - * is booted anyway. - * - * Note uboot's tftp flash install writes the transferred - * image to both kernel partitions. - */ - - partition@200000 { - label = "kernel_stock"; - reg = <0x200000 0x400000>; - }; - - partition@600000 { - label = "kernel"; - reg = <0x600000 0x400000>; - }; - - /* ubi partition is the result of squashing - * next consecutive stock partitions: - * - rootfs0 (rootfs partition for stock kernel0), - * - rootfs1 (rootfs partition for stock failsafe kernel1), - * - overlay (used as ubi overlay in stock fw) - * resulting 117,5MiB space for packages. - */ - - partition@a00000 { - label = "ubi"; - reg = <0xa00000 0x7580000>; - }; - }; -}; - -&pcie { - status = "okay"; -}; - -&pcie0 { - wifi@0,0 { - compatible = "pci14c3,7603"; - reg = <0x0000 0 0 0 0>; - mediatek,mtd-eeprom = <&factory 0x0000>; - ieee80211-freq-limit = <2400000 2500000>; - }; -}; - -&pcie1 { - wifi@0,0 { - compatible = "pci14c3,7662"; - reg = <0x0000 0 0 0 0>; - mediatek,mtd-eeprom = <&factory 0x8000>; - ieee80211-freq-limit = <5000000 6000000>; - }; -}; - -&gmac0 { - mtd-mac-address = <&factory 0xe006>; -}; - -&switch0 { - ports { - port@1 { - status = "okay"; - label = "wan"; - mtd-mac-address = <&factory 0xe000>; - }; - - port@2 { - status = "okay"; - label = "lan2"; - }; - - port@3 { - status = "okay"; - label = "lan1"; - }; - }; -}; - -&state_default { - gpio { - groups = "jtag", "uart2", "uart3", "wdt"; - function = "gpio"; - }; -}; diff --git a/target/linux/ramips/dts/mt7621_xiaomi_mir3p.dts b/target/linux/ramips/dts/mt7621_xiaomi_mir3p.dts deleted file mode 100644 index 43e61e9140..0000000000 --- a/target/linux/ramips/dts/mt7621_xiaomi_mir3p.dts +++ /dev/null @@ -1,212 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later OR MIT - -#include "mt7621.dtsi" - -#include -#include - -/ { - compatible = "xiaomi,mir3p", "mediatek,mt7621-soc"; - model = "Xiaomi Mi Router 3 Pro"; - - aliases { - led-boot = &led_status_yellow; - led-failsafe = &led_status_red; - led-running = &led_status_blue; - led-upgrade = &led_status_yellow; - label-mac-device = &gmac0; - }; - - chosen { - bootargs = "console=ttyS0,115200n8"; - }; - - leds { - compatible = "gpio-leds"; - - led_status_red: status_red { - label = "red:status"; - gpios = <&gpio 6 GPIO_ACTIVE_LOW>; - }; - - led_status_blue: status_blue { - label = "blue:status"; - gpios = <&gpio 8 GPIO_ACTIVE_LOW>; - }; - - led_status_yellow: status_yellow { - label = "yellow:status"; - gpios = <&gpio 10 GPIO_ACTIVE_LOW>; - }; - - wan_amber { - label = "amber:wan"; - gpios = <&gpio 14 GPIO_ACTIVE_LOW>; - linux,default-trigger = "dsa-0.0:04:1Gbps"; - }; - - lan3_amber { - label = "amber:lan3"; - gpios = <&gpio 13 GPIO_ACTIVE_LOW>; - linux,default-trigger = "dsa-0.0:01:1Gbps"; - }; - - lan2_amber { - label = "amber:lan2"; - gpios = <&gpio 16 GPIO_ACTIVE_LOW>; - linux,default-trigger = "dsa-0.0:02:1Gbps"; - }; - - lan1_amber { - label = "amber:lan1"; - gpios = <&gpio 15 GPIO_ACTIVE_LOW>; - linux,default-trigger = "dsa-0.0:03:1Gbps"; - }; - }; - - keys { - compatible = "gpio-keys"; - - reset { - label = "reset"; - gpios = <&gpio 18 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - reg_usb_vbus: regulator { - compatible = "regulator-fixed"; - regulator-name = "usb_vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - gpio = <&gpio 12 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; -}; - -&xhci { - vbus-supply = <®_usb_vbus>; -}; - -&nand { - status = "okay"; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "Bootloader"; - reg = <0x0 0x40000>; - read-only; - }; - - partition@40000 { - label = "Config"; - reg = <0x40000 0x40000>; - }; - - partition@80000 { - label = "Bdata"; - reg = <0x80000 0x40000>; - read-only; - }; - - factory: partition@c0000 { - label = "factory"; - reg = <0x0c0000 0x40000>; - read-only; - }; - - partition@100000 { - label = "crash"; - reg = <0x100000 0x40000>; - }; - - partition@140000 { - label = "crash_syslog"; - reg = <0x140000 0x80000>; - }; - - partition@1c0000 { - label = "reserved0"; - reg = <0x1c0000 0x40000>; - read-only; - }; - - /* We keep stock xiaomi firmware (kernel0) here */ - partition@200000 { - label = "kernel_stock"; - reg = <0x200000 0x400000>; - }; - - partition@600000 { - label = "kernel"; - reg = <0x600000 0x400000>; - }; - - partition@a00000 { - label = "ubi"; - reg = <0xa00000 0xf580000>; - }; - }; -}; - -&pcie { - status = "okay"; -}; - -&pcie0 { - wifi@0,0 { - compatible = "mediatek,mt76"; - reg = <0x0000 0 0 0 0>; - mediatek,mtd-eeprom = <&factory 0x0000>; - ieee80211-freq-limit = <2400000 2500000>; - }; -}; - -&pcie1 { - wifi@0,0 { - compatible = "mediatek,mt76"; - reg = <0x0000 0 0 0 0>; - mediatek,mtd-eeprom = <&factory 0x8000>; - ieee80211-freq-limit = <5000000 6000000>; - }; -}; - -&gmac0 { - mtd-mac-address = <&factory 0xe006>; -}; - -&switch0 { - ports { - port@1 { - status = "okay"; - label = "lan3"; - }; - - port@2 { - status = "okay"; - label = "lan2"; - }; - - port@3 { - status = "okay"; - label = "lan1"; - }; - - port@4 { - status = "okay"; - label = "wan"; - mtd-mac-address = <&factory 0xe000>; - }; - }; -}; - -&state_default { - gpio { - groups = "jtag", "uart2", "uart3", "wdt"; - function = "gpio"; - }; -}; diff --git a/target/linux/ramips/dts/mt7628an_xiaomi_mi-router-4a-100m.dts b/target/linux/ramips/dts/mt7628an_xiaomi_mi-router-4a-100m.dts new file mode 100644 index 0000000000..37797fc368 --- /dev/null +++ b/target/linux/ramips/dts/mt7628an_xiaomi_mi-router-4a-100m.dts @@ -0,0 +1,45 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "mt7628an_xiaomi_mi-router-4.dtsi" + +/ { + compatible = "xiaomi,mi-router-4a-100m", "mediatek,mt7628an-soc"; + model = "Xiaomi Mi Router 4A (100M Edition)"; +}; + +&partitions { + partition@60000 { + label = "overlay"; + reg = <0x60000 0x100000>; + read-only; + }; + + partition@160000 { + label = "firmware"; + reg = <0x160000 0xea0000>; + compatible = "denx,uimage"; + }; +}; + +&pcie { + status = "okay"; +}; + +&pcie0 { + wifi@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0000 0 0 0 0>; + mediatek,mtd-eeprom = <&factory 0x8000>; + ieee80211-freq-limit = <5000000 6000000>; + }; +}; + +ðernet { + mtd-mac-address = <&factory 0x4>; + mtd-mac-address-increment = <(-1)>; +}; + +&esw { + mediatek,portmap = <0x3e>; + mediatek,portdisable = <0x2a>; +}; diff --git a/target/linux/ramips/dts/mt7628an_xiaomi_mir4a-100m.dts b/target/linux/ramips/dts/mt7628an_xiaomi_mir4a-100m.dts deleted file mode 100644 index a1a7dc7383..0000000000 --- a/target/linux/ramips/dts/mt7628an_xiaomi_mir4a-100m.dts +++ /dev/null @@ -1,45 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later OR MIT - -#include "mt7628an_xiaomi_mi-router-4.dtsi" - -/ { - compatible = "xiaomi,mir4a-100m", "mediatek,mt7628an-soc"; - model = "Xiaomi Mi Router 4A (100M Edition)"; -}; - -&partitions { - partition@60000 { - label = "overlay"; - reg = <0x60000 0x100000>; - read-only; - }; - - partition@160000 { - label = "firmware"; - reg = <0x160000 0xea0000>; - compatible = "denx,uimage"; - }; -}; - -&pcie { - status = "okay"; -}; - -&pcie0 { - wifi@0,0 { - compatible = "mediatek,mt76"; - reg = <0x0000 0 0 0 0>; - mediatek,mtd-eeprom = <&factory 0x8000>; - ieee80211-freq-limit = <5000000 6000000>; - }; -}; - -ðernet { - mtd-mac-address = <&factory 0x4>; - mtd-mac-address-increment = <(-1)>; -}; - -&esw { - mediatek,portmap = <0x3e>; - mediatek,portdisable = <0x2a>; -}; diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk index 7b8a73c1bd..fad18552c9 100644 --- a/target/linux/ramips/image/mt7621.mk +++ b/target/linux/ramips/image/mt7621.mk @@ -1191,13 +1191,7 @@ define Device/xiaomi-ac2100 uboot-envtools endef -define Device/xiaomi_mi-router-ac2100 - $(Device/xiaomi-ac2100) - DEVICE_MODEL := Mi Router AC2100 -endef -TARGET_DEVICES += xiaomi_mi-router-ac2100 - -define Device/xiaomi_mir3g +define Device/xiaomi_mi-router-3g $(Device/dsa-migration) $(Device/uimage-lzma-loader) BLOCKSIZE := 128k @@ -1211,14 +1205,13 @@ define Device/xiaomi_mir3g IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata DEVICE_VENDOR := Xiaomi DEVICE_MODEL := Mi Router 3G - SUPPORTED_DEVICES += R3G - SUPPORTED_DEVICES += mir3g DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \ kmod-usb-ledtrig-usbport uboot-envtools + SUPPORTED_DEVICES += R3G mir3g xiaomi,mir3g endef -TARGET_DEVICES += xiaomi_mir3g +TARGET_DEVICES += xiaomi_mi-router-3g -define Device/xiaomi_mir3g-v2 +define Device/xiaomi_mi-router-3g-v2 $(Device/dsa-migration) $(Device/uimage-lzma-loader) IMAGE_SIZE := 14848k @@ -1226,10 +1219,11 @@ define Device/xiaomi_mir3g-v2 DEVICE_MODEL := Mi Router 3G DEVICE_VARIANT := v2 DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 + SUPPORTED_DEVICES += xiaomi,mir3g-v2 endef -TARGET_DEVICES += xiaomi_mir3g-v2 +TARGET_DEVICES += xiaomi_mi-router-3g-v2 -define Device/xiaomi_mir3p +define Device/xiaomi_mi-router-3-pro $(Device/dsa-migration) $(Device/uimage-lzma-loader) BLOCKSIZE := 128k @@ -1245,8 +1239,9 @@ define Device/xiaomi_mir3p check-size DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3 \ kmod-usb-ledtrig-usbport uboot-envtools + SUPPORTED_DEVICES += xiaomi,mir3p endef -TARGET_DEVICES += xiaomi_mir3p +TARGET_DEVICES += xiaomi_mi-router-3-pro define Device/xiaomi_mi-router-4a-gigabit $(Device/dsa-migration) @@ -1259,6 +1254,12 @@ define Device/xiaomi_mi-router-4a-gigabit endef TARGET_DEVICES += xiaomi_mi-router-4a-gigabit +define Device/xiaomi_mi-router-ac2100 + $(Device/xiaomi-ac2100) + DEVICE_MODEL := Mi Router AC2100 +endef +TARGET_DEVICES += xiaomi_mi-router-ac2100 + define Device/xiaomi_redmi-router-ac2100 $(Device/xiaomi-ac2100) DEVICE_MODEL := Redmi Router AC2100 diff --git a/target/linux/ramips/image/mt76x8.mk b/target/linux/ramips/image/mt76x8.mk index edd42a4dd5..00593dd6f5 100644 --- a/target/linux/ramips/image/mt76x8.mk +++ b/target/linux/ramips/image/mt76x8.mk @@ -743,14 +743,15 @@ define Device/wrtnode_wrtnode2r endef TARGET_DEVICES += wrtnode_wrtnode2r -define Device/xiaomi_mir4a-100m +define Device/xiaomi_mi-router-4a-100m IMAGE_SIZE := 14976k DEVICE_VENDOR := Xiaomi DEVICE_MODEL := Mi Router 4A DEVICE_VARIANT := 100M Edition DEVICE_PACKAGES := kmod-mt76x2 + SUPPORTED_DEVICES += xiaomi,mir4a-100m endef -TARGET_DEVICES += xiaomi_mir4a-100m +TARGET_DEVICES += xiaomi_mi-router-4a-100m define Device/xiaomi_mi-router-4c IMAGE_SIZE := 14976k diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network index fccd9c6985..c5b35145f1 100755 --- a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network +++ b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network @@ -16,8 +16,8 @@ ramips_setup_interfaces() asiarf,ap7621-nv1|\ lenovo,newifi-d1|\ mikrotik,routerboard-m33g|\ - xiaomi,mir3g|\ - xiaomi,mir3g-v2|\ + xiaomi,mi-router-3g|\ + xiaomi,mi-router-3g-v2|\ xiaomi,mi-router-4a-gigabit) ucidef_set_interfaces_lan_wan "lan1 lan2" "wan" ;; @@ -33,8 +33,8 @@ ramips_setup_interfaces() ;; gehua,ghl-r-001|\ hiwifi,hc5962|\ + xiaomi,mi-router-3-pro|\ xiaomi,mi-router-ac2100|\ - xiaomi,mir3p|\ xiaomi,redmi-router-ac2100) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" "wan" ;; diff --git a/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh b/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh index b4d07f8146..c68b012d0b 100755 --- a/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh +++ b/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh @@ -61,9 +61,9 @@ platform_do_upgrade() { netgear,wac104|\ netgear,wac124|\ netis,wf2881|\ + xiaomi,mi-router-3g|\ + xiaomi,mi-router-3-pro|\ xiaomi,mi-router-ac2100|\ - xiaomi,mir3g|\ - xiaomi,mir3p|\ xiaomi,redmi-router-ac2100) nand_do_upgrade "$1" ;; diff --git a/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network b/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network index 6f0078c70a..fcc2630b3f 100755 --- a/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network +++ b/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network @@ -133,7 +133,7 @@ ramips_setup_interfaces() ucidef_add_switch "switch0" \ "0:wan" "3:lan" "4:lan" "6@eth0" ;; - xiaomi,mir4a-100m) + xiaomi,mi-router-4a-100m) ucidef_add_switch "switch0" \ "4:lan:1" "2:lan:2" "0:wan" "6@eth0" ;; @@ -238,8 +238,8 @@ ramips_setup_macs() label_mac=$(mtd_get_mac_binary factory 0x4) wan_mac=$(mtd_get_mac_binary factory 0x28) ;; - xiaomi,mi-router-4c|\ - xiaomi,mir4a-100m) + xiaomi,mi-router-4a-100m|\ + xiaomi,mi-router-4c) wan_mac=$(mtd_get_mac_binary factory 0x4) ;; esac