From: FUKAUMI Naoki Date: Sat, 28 Jan 2017 16:05:56 +0000 (+0900) Subject: ramips: add support for Buffalo WCR-1166DS X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=6b0b526a4fc11d3b1b588d5b3b789da0c66adce9;p=openwrt%2Fstaging%2Fjow.git ramips: add support for Buffalo WCR-1166DS Buffalo WCR-1166DS is a small wireless router with - MT7628AN + MT7612E - 64MiB DDR2 SDRAM - 16MiB SPI flash - 2T2R 11ac/a/b/g/n Wi-Fi - 2x 10/100M ethernet switch - 8x programmable LED - 3x button - UART pad on PCB (J2: 3.3V, GND, TX, RX) factory image can be installed via stock web UI. due to the "dual image" function in the bootloader, the second half of the SPI flash ("firmware2" partition) cannot be used as a part of the file system. Signed-off-by: FUKAUMI Naoki --- diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network index 91f1aaacbe..c001dfe85a 100755 --- a/target/linux/ramips/base-files/etc/board.d/02_network +++ b/target/linux/ramips/base-files/etc/board.d/02_network @@ -263,6 +263,10 @@ ramips_setup_interfaces() ucidef_add_switch "switch0" \ "1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "5@eth0" ;; + wcr-1166ds) + ucidef_add_switch "switch0" \ + "3:lan" "4:wan" "6@eth0" + ;; wcr-150gn) ucidef_add_switch "switch0" \ "0:lan" "6t@eth0" @@ -410,6 +414,12 @@ ramips_setup_macs() lan_mac=$(cat /sys/class/net/eth0/address) wan_mac=$(macaddr_add "$lan_mac" 5) ;; + wcr-1166ds|\ + wsr-1166) + local index="$(find_mtd_index "board_data")" + wan_mac="$(grep -m1 mac= "/dev/mtd${index}" | cut -d= -f2)" + lan_mac=$wan_mac + ;; wcr-150gn) wan_mac=$(mtd_get_mac_binary factory 40) ;; @@ -427,11 +437,6 @@ ramips_setup_macs() wlr-6000) wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 32772)" 2) ;; - wsr-1166) - local index="$(find_mtd_index "board_data")" - wan_mac="$(grep -m1 mac= "/dev/mtd${index}" | cut -d= -f2)" - lan_mac=$wan_mac - ;; *) lan_mac=$(cat /sys/class/net/eth0/address) wan_mac=$(macaddr_add "$lan_mac" 1) diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh index 94998333b3..5fb221380e 100644 --- a/target/linux/ramips/base-files/etc/diag.sh +++ b/target/linux/ramips/base-files/etc/diag.sh @@ -219,6 +219,12 @@ get_status_led() { zbt-wr8305rt) status_led="$board:green:sys" ;; + wcr-1166ds|\ + whr-300hp2|\ + wsr-1166|\ + wsr-600) + status_led="$board:green:power" + ;; wcr-150gn|\ wl-351) status_led="$board:amber:power" @@ -233,11 +239,6 @@ get_status_led() { wizfi630a) status_led="$board::run" ;; - whr-300hp2|\ - wsr-1166|\ - wsr-600) - status_led="$board:green:power" - ;; wrtnode2r | \ wrtnode2p | \ wrtnode) diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh index 8292da1d4a..d9918cceb5 100755 --- a/target/linux/ramips/base-files/lib/ramips.sh +++ b/target/linux/ramips/base-files/lib/ramips.sh @@ -499,6 +499,9 @@ ramips_board_detect() { *"W502U") name="w502u" ;; + *"WCR-1166DS") + name="wcr-1166ds" + ;; *"WCR-150GN") name="wcr-150gn" ;; diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh index c6ad8ca3e5..d83e5c1dd2 100755 --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh @@ -226,6 +226,11 @@ platform_check_image() { } return 0 ;; + ubnt-erx) + nand_do_platform_check "$board" "$1" + return $?; + ;; + wcr-1166ds|\ wsr-1166) [ "$magic" != "48445230" ] && { echo "Invalid image type." @@ -233,10 +238,6 @@ platform_check_image() { } return 0 ;; - ubnt-erx) - nand_do_platform_check "$board" "$1" - return $?; - ;; esac echo "Sysupgrade is not yet supported on $board." diff --git a/target/linux/ramips/dts/WCR-1166DS.dts b/target/linux/ramips/dts/WCR-1166DS.dts new file mode 100644 index 0000000000..ad3f21ba67 --- /dev/null +++ b/target/linux/ramips/dts/WCR-1166DS.dts @@ -0,0 +1,172 @@ +/dts-v1/; + +#include "mt7628an.dtsi" + +#include +#include + +/ { + compatible = "buffalo,wcr-1166ds", "mediatek,mt7628an-soc"; + model = "Buffalo WCR-1166DS"; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <20>; + + aoss { + label = "aoss"; + gpios = <&gpio0 0 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + ap { + label = "ap"; + gpios = <&gpio0 11 GPIO_ACTIVE_LOW>; + linux,code = ; + linux,input-type = ; + }; + + reset { + label = "reset"; + gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + router_o { + label = "wcr-1166ds:orange:router"; + gpios = <&gpio1 5 GPIO_ACTIVE_LOW>; + }; + + router_g { + label = "wcr-1166ds:green:router"; + gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; + }; + + internet_o { + label = "wcr-1166ds:orange:internet"; + gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; + }; + + internet_g { + label = "wcr-1166ds:green:internet"; + gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; + }; + + wireless_o { + label = "wcr-1166ds:orange:wireless"; + gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; + }; + + wireless_g { + label = "wcr-1166ds:green:wireless"; + gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; + }; + + diag { + label = "wcr-1166ds:orange:diag"; + gpios = <&gpio1 11 GPIO_ACTIVE_LOW>; + }; + + power { + label = "wcr-1166ds:green:power"; + gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&ehci { + status = "disabled"; +}; + +&esw { + mediatek,portmap = <0x2f>; + mediatek,portdisable = <0x27>; +}; + +&ohci { + status = "disabled"; +}; + +&pcie { + status = "okay"; + pcie-bridge { + mt76@0,0 { + reg = <0x0000 0 0 0 0>; + device_type = "pci"; + mediatek,mtd-eeprom = <&factory 0x8000>; + mediatek,2ghz = <0>; + }; + }; +}; + +&pinctrl { + state_default: pinctrl0 { + gpio { + ralink,group = "uart1", "wled_an", "p0led_an", "p1led_an", "p2led_an", "p3led_an", "p4led_an", "wdt", "refclk", "gpio", "i2s"; + ralink,function = "gpio"; + }; + }; +}; + +&spi0 { + status = "okay"; + + m25p80@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <10000000>; + m25p,chunked-io = <32>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x30000>; + read-only; + }; + + partition@30000 { + label = "u-boot-env"; + reg = <0x30000 0x10000>; + read-only; + }; + + factory: partition@40000 { + label = "factory"; + reg = <0x40000 0x10000>; + read-only; + }; + + partition@50000 { + label = "firmware"; + reg = <0x50000 0x7c0000>; + }; + + partition@810000 { + label = "firmware2"; + reg = <0x810000 0x7c0000>; + }; + + partition@fd0000 { + label = "glbcfg"; + reg = <0xfd0000 0x10000>; + read-only; + }; + + partition@fe0000 { + label = "board_data"; + reg = <0xfe0000 0x10000>; + read-only; + }; + }; +}; + +&wmac { + status = "okay"; +}; diff --git a/target/linux/ramips/image/Makefile b/target/linux/ramips/image/Makefile index 2952c5f840..f34eba79cd 100644 --- a/target/linux/ramips/image/Makefile +++ b/target/linux/ramips/image/Makefile @@ -23,6 +23,7 @@ define Image/Build/Initramfs endef DEVICE_VARS += DTS IMAGE_SIZE NETGEAR_BOARD_ID NETGEAR_HW_ID +DEVICE_VARS += BUFFALO_TAG_PLATFORM BUFFALO_TAG_VERSION BUFFALO_TAG_MINOR loadaddr-y := 0x80000000 loadaddr-$(CONFIG_TARGET_ramips_rt288x) := 0x88000000 @@ -48,7 +49,7 @@ define Build/patch-dtb endef define Build/trx - $(STAGING_DIR_HOST)/bin/trx \ + $(STAGING_DIR_HOST)/bin/trx $(1) \ -o $@ \ -m $(IMAGE_SIZE) \ -f $(IMAGE_KERNEL) \ diff --git a/target/linux/ramips/image/mt7628.mk b/target/linux/ramips/image/mt7628.mk index 4502588c80..0304921f41 100644 --- a/target/linux/ramips/image/mt7628.mk +++ b/target/linux/ramips/image/mt7628.mk @@ -55,3 +55,19 @@ define Device/mac1200r-v2 DEVICE_TITLE := Mercury MAC1200R v2.0 endef TARGET_DEVICES += mac1200r-v2 + +define Device/wcr-1166ds + DTS := WCR-1166DS + BUFFALO_TAG_PLATFORM := MTK + BUFFALO_TAG_VERSION := 9.99 + BUFFALO_TAG_MINOR := 9.99 + IMAGES += factory.bin + IMAGE/sysupgrade.bin := trx | pad-rootfs | append-metadata + IMAGE/factory.bin := \ + trx -M 0x746f435c | pad-rootfs | append-metadata | \ + buffalo-enc WCR-1166DS $$(BUFFALO_TAG_VERSION) -l | \ + buffalo-tag-dhp WCR-1166DS JP JP | buffalo-enc-tag -l | \ + buffalo-dhp-image + DEVICE_TITLE := Buffalo WCR-1166DS +endef +TARGET_DEVICES += wcr-1166ds diff --git a/target/linux/ramips/mt7628/config-4.4 b/target/linux/ramips/mt7628/config-4.4 index 6b04457f17..6cd7838aee 100644 --- a/target/linux/ramips/mt7628/config-4.4 +++ b/target/linux/ramips/mt7628/config-4.4 @@ -138,6 +138,7 @@ CONFIG_MTD_NAND_MT7620=y CONFIG_MTD_PHYSMAP=y CONFIG_MTD_SPI_NOR=y CONFIG_MTD_SPLIT_FIRMWARE=y +CONFIG_MTD_SPLIT_TRX_FW=y CONFIG_MTD_SPLIT_UIMAGE_FW=y CONFIG_NEED_DMA_MAP_STATE=y CONFIG_NEED_PER_CPU_KM=y diff --git a/target/linux/ramips/patches-4.4/0400-mtd-mtdsplit-add-support-for-custom-trx-magic-for-Buffalo-WCR-1166DS.patch b/target/linux/ramips/patches-4.4/0400-mtd-mtdsplit-add-support-for-custom-trx-magic-for-Buffalo-WCR-1166DS.patch new file mode 100644 index 0000000000..1af72f93df --- /dev/null +++ b/target/linux/ramips/patches-4.4/0400-mtd-mtdsplit-add-support-for-custom-trx-magic-for-Buffalo-WCR-1166DS.patch @@ -0,0 +1,30 @@ +--- a/drivers/mtd/mtdsplit/mtdsplit_trx.c ++++ b/drivers/mtd/mtdsplit/mtdsplit_trx.c +@@ -13,6 +13,7 @@ + #include + #include + #include ++#include + #include + #include + #include +@@ -20,7 +21,8 @@ + + #include "mtdsplit.h" + +-#define TRX_MAGIC 0x30524448 /* "HDR0" */ ++#define TRX_MAGIC 0x30524448 /* "HDR0" */ ++#define TRX_MAGIC_BUFFALO 0x746f435c + + struct trx_header { + __le32 magic; +@@ -82,7 +84,8 @@ mtdsplit_parse_trx(struct mtd_info *mast + if (ret) + continue; + +- if (hdr.magic != cpu_to_le32(TRX_MAGIC)) { ++ if (hdr.magic != cpu_to_le32(TRX_MAGIC) && ++ !(of_machine_is_compatible("buffalo,wcr-1166ds") && hdr.magic == cpu_to_le32(TRX_MAGIC_BUFFALO))) { + pr_debug("no valid trx header found in \"%s\" at offset %llx\n", + master->name, (unsigned long long) offset); + continue;