From: Alexander Duyck Date: Thu, 19 Apr 2012 17:49:56 +0000 (+0000) Subject: ixgbe: Reorder link flow control functions in ixgbe_common.c X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=67a79df27163a89fb1ce2191718855288071cbd2;p=openwrt%2Fstaging%2Fblogic.git ixgbe: Reorder link flow control functions in ixgbe_common.c We can avoid many of the forward declarations found in ixgbe_common.c by just reordering things so this patch does that to help cleanup the code. Signed-off-by: Alexander Duyck Tested-by: Ross Brattain Signed-off-by: Jeff Kirsher --- diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c index 9854d948f135..3035f1938f5b 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c @@ -47,13 +47,6 @@ static void ixgbe_lower_eeprom_clk(struct ixgbe_hw *hw, u32 *eec); static void ixgbe_release_eeprom(struct ixgbe_hw *hw); static s32 ixgbe_mta_vector(struct ixgbe_hw *hw, u8 *mc_addr); -static s32 ixgbe_fc_autoneg_fiber(struct ixgbe_hw *hw); -static s32 ixgbe_fc_autoneg_backplane(struct ixgbe_hw *hw); -static s32 ixgbe_fc_autoneg_copper(struct ixgbe_hw *hw); -static s32 ixgbe_device_supports_autoneg_fc(struct ixgbe_hw *hw); -static s32 ixgbe_negotiate_fc(struct ixgbe_hw *hw, u32 adv_reg, u32 lp_reg, - u32 adv_sym, u32 adv_asm, u32 lp_sym, u32 lp_asm); -static s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num); static s32 ixgbe_poll_eerd_eewr_done(struct ixgbe_hw *hw, u32 ee_reg); static s32 ixgbe_read_eeprom_buffer_bit_bang(struct ixgbe_hw *hw, u16 offset, u16 words, u16 *data); @@ -63,6 +56,216 @@ static s32 ixgbe_detect_eeprom_page_size_generic(struct ixgbe_hw *hw, u16 offset); static s32 ixgbe_disable_pcie_master(struct ixgbe_hw *hw); +/** + * ixgbe_device_supports_autoneg_fc - Check if phy supports autoneg flow + * control + * @hw: pointer to hardware structure + * + * There are several phys that do not support autoneg flow control. This + * function check the device id to see if the associated phy supports + * autoneg flow control. + **/ +static s32 ixgbe_device_supports_autoneg_fc(struct ixgbe_hw *hw) +{ + + switch (hw->device_id) { + case IXGBE_DEV_ID_X540T: + return 0; + case IXGBE_DEV_ID_82599_T3_LOM: + return 0; + default: + return IXGBE_ERR_FC_NOT_SUPPORTED; + } +} + +/** + * ixgbe_setup_fc - Set up flow control + * @hw: pointer to hardware structure + * + * Called at init time to set up flow control. + **/ +static s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num) +{ + s32 ret_val = 0; + u32 reg = 0, reg_bp = 0; + u16 reg_cu = 0; + +#ifdef CONFIG_DCB + if (hw->fc.requested_mode == ixgbe_fc_pfc) { + hw->fc.current_mode = hw->fc.requested_mode; + goto out; + } + +#endif /* CONFIG_DCB */ + /* Validate the packetbuf configuration */ + if (packetbuf_num < 0 || packetbuf_num > 7) { + hw_dbg(hw, "Invalid packet buffer number [%d], expected range is 0-7\n", + packetbuf_num); + ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS; + goto out; + } + + /* + * Validate the water mark configuration. Zero water marks are invalid + * because it causes the controller to just blast out fc packets. + */ + if (!hw->fc.low_water || + !hw->fc.high_water[packetbuf_num] || + !hw->fc.pause_time) { + hw_dbg(hw, "Invalid water mark configuration\n"); + ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS; + goto out; + } + + /* + * Validate the requested mode. Strict IEEE mode does not allow + * ixgbe_fc_rx_pause because it will cause us to fail at UNH. + */ + if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) { + hw_dbg(hw, "ixgbe_fc_rx_pause not valid in strict IEEE mode\n"); + ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS; + goto out; + } + + /* + * 10gig parts do not have a word in the EEPROM to determine the + * default flow control setting, so we explicitly set it to full. + */ + if (hw->fc.requested_mode == ixgbe_fc_default) + hw->fc.requested_mode = ixgbe_fc_full; + + /* + * Set up the 1G and 10G flow control advertisement registers so the + * HW will be able to do fc autoneg once the cable is plugged in. If + * we link at 10G, the 1G advertisement is harmless and vice versa. + */ + + switch (hw->phy.media_type) { + case ixgbe_media_type_fiber: + case ixgbe_media_type_backplane: + reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA); + reg_bp = IXGBE_READ_REG(hw, IXGBE_AUTOC); + break; + + case ixgbe_media_type_copper: + hw->phy.ops.read_reg(hw, MDIO_AN_ADVERTISE, + MDIO_MMD_AN, ®_cu); + break; + + default: + ; + } + + /* + * The possible values of fc.requested_mode are: + * 0: Flow control is completely disabled + * 1: Rx flow control is enabled (we can receive pause frames, + * but not send pause frames). + * 2: Tx flow control is enabled (we can send pause frames but + * we do not support receiving pause frames). + * 3: Both Rx and Tx flow control (symmetric) are enabled. +#ifdef CONFIG_DCB + * 4: Priority Flow Control is enabled. +#endif + * other: Invalid. + */ + switch (hw->fc.requested_mode) { + case ixgbe_fc_none: + /* Flow control completely disabled by software override. */ + reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE); + if (hw->phy.media_type == ixgbe_media_type_backplane) + reg_bp &= ~(IXGBE_AUTOC_SYM_PAUSE | + IXGBE_AUTOC_ASM_PAUSE); + else if (hw->phy.media_type == ixgbe_media_type_copper) + reg_cu &= ~(IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE); + break; + case ixgbe_fc_rx_pause: + /* + * Rx Flow control is enabled and Tx Flow control is + * disabled by software override. Since there really + * isn't a way to advertise that we are capable of RX + * Pause ONLY, we will advertise that we support both + * symmetric and asymmetric Rx PAUSE. Later, we will + * disable the adapter's ability to send PAUSE frames. + */ + reg |= (IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE); + if (hw->phy.media_type == ixgbe_media_type_backplane) + reg_bp |= (IXGBE_AUTOC_SYM_PAUSE | + IXGBE_AUTOC_ASM_PAUSE); + else if (hw->phy.media_type == ixgbe_media_type_copper) + reg_cu |= (IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE); + break; + case ixgbe_fc_tx_pause: + /* + * Tx Flow control is enabled, and Rx Flow control is + * disabled by software override. + */ + reg |= (IXGBE_PCS1GANA_ASM_PAUSE); + reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE); + if (hw->phy.media_type == ixgbe_media_type_backplane) { + reg_bp |= (IXGBE_AUTOC_ASM_PAUSE); + reg_bp &= ~(IXGBE_AUTOC_SYM_PAUSE); + } else if (hw->phy.media_type == ixgbe_media_type_copper) { + reg_cu |= (IXGBE_TAF_ASM_PAUSE); + reg_cu &= ~(IXGBE_TAF_SYM_PAUSE); + } + break; + case ixgbe_fc_full: + /* Flow control (both Rx and Tx) is enabled by SW override. */ + reg |= (IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE); + if (hw->phy.media_type == ixgbe_media_type_backplane) + reg_bp |= (IXGBE_AUTOC_SYM_PAUSE | + IXGBE_AUTOC_ASM_PAUSE); + else if (hw->phy.media_type == ixgbe_media_type_copper) + reg_cu |= (IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE); + break; +#ifdef CONFIG_DCB + case ixgbe_fc_pfc: + goto out; + break; +#endif /* CONFIG_DCB */ + default: + hw_dbg(hw, "Flow control param set incorrectly\n"); + ret_val = IXGBE_ERR_CONFIG; + goto out; + break; + } + + if (hw->mac.type != ixgbe_mac_X540) { + /* + * Enable auto-negotiation between the MAC & PHY; + * the MAC will advertise clause 37 flow control. + */ + IXGBE_WRITE_REG(hw, IXGBE_PCS1GANA, reg); + reg = IXGBE_READ_REG(hw, IXGBE_PCS1GLCTL); + + /* Disable AN timeout */ + if (hw->fc.strict_ieee) + reg &= ~IXGBE_PCS1GLCTL_AN_1G_TIMEOUT_EN; + + IXGBE_WRITE_REG(hw, IXGBE_PCS1GLCTL, reg); + hw_dbg(hw, "Set up FC; PCS1GLCTL = 0x%08X\n", reg); + } + + /* + * AUTOC restart handles negotiation of 1G and 10G on backplane + * and copper. There is no need to set the PCS1GCTL register. + * + */ + if (hw->phy.media_type == ixgbe_media_type_backplane) { + reg_bp |= IXGBE_AUTOC_AN_RESTART; + IXGBE_WRITE_REG(hw, IXGBE_AUTOC, reg_bp); + } else if ((hw->phy.media_type == ixgbe_media_type_copper) && + (ixgbe_device_supports_autoneg_fc(hw) == 0)) { + hw->phy.ops.write_reg(hw, MDIO_AN_ADVERTISE, + MDIO_MMD_AN, reg_cu); + } + + hw_dbg(hw, "Set up FC; IXGBE_AUTOC = 0x%08X\n", reg); +out: + return ret_val; +} + /** * ixgbe_start_hw_generic - Prepare hardware for Tx/Rx * @hw: pointer to hardware structure @@ -2043,63 +2246,52 @@ out: } /** - * ixgbe_fc_autoneg - Configure flow control + * ixgbe_negotiate_fc - Negotiate flow control * @hw: pointer to hardware structure + * @adv_reg: flow control advertised settings + * @lp_reg: link partner's flow control settings + * @adv_sym: symmetric pause bit in advertisement + * @adv_asm: asymmetric pause bit in advertisement + * @lp_sym: symmetric pause bit in link partner advertisement + * @lp_asm: asymmetric pause bit in link partner advertisement * - * Compares our advertised flow control capabilities to those advertised by - * our link partner, and determines the proper flow control mode to use. + * Find the intersection between advertised settings and link partner's + * advertised settings **/ -void ixgbe_fc_autoneg(struct ixgbe_hw *hw) +static s32 ixgbe_negotiate_fc(struct ixgbe_hw *hw, u32 adv_reg, u32 lp_reg, + u32 adv_sym, u32 adv_asm, u32 lp_sym, u32 lp_asm) { - s32 ret_val = IXGBE_ERR_FC_NOT_NEGOTIATED; - ixgbe_link_speed speed; - bool link_up; - - /* - * AN should have completed when the cable was plugged in. - * Look for reasons to bail out. Bail out if: - * - FC autoneg is disabled, or if - * - link is not up. - * - * Since we're being called from an LSC, link is already known to be up. - * So use link_up_wait_to_complete=false. - */ - if (hw->fc.disable_fc_autoneg) - goto out; - - hw->mac.ops.check_link(hw, &speed, &link_up, false); - if (!link_up) - goto out; - - switch (hw->phy.media_type) { - /* Autoneg flow control on fiber adapters */ - case ixgbe_media_type_fiber: - if (speed == IXGBE_LINK_SPEED_1GB_FULL) - ret_val = ixgbe_fc_autoneg_fiber(hw); - break; - - /* Autoneg flow control on backplane adapters */ - case ixgbe_media_type_backplane: - ret_val = ixgbe_fc_autoneg_backplane(hw); - break; + if ((!(adv_reg)) || (!(lp_reg))) + return IXGBE_ERR_FC_NOT_NEGOTIATED; - /* Autoneg flow control on copper adapters */ - case ixgbe_media_type_copper: - if (ixgbe_device_supports_autoneg_fc(hw) == 0) - ret_val = ixgbe_fc_autoneg_copper(hw); - break; - - default: - break; - } - -out: - if (ret_val == 0) { - hw->fc.fc_was_autonegged = true; + if ((adv_reg & adv_sym) && (lp_reg & lp_sym)) { + /* + * Now we need to check if the user selected Rx ONLY + * of pause frames. In this case, we had to advertise + * FULL flow control because we could not advertise RX + * ONLY. Hence, we must now check to see if we need to + * turn OFF the TRANSMISSION of PAUSE frames. + */ + if (hw->fc.requested_mode == ixgbe_fc_full) { + hw->fc.current_mode = ixgbe_fc_full; + hw_dbg(hw, "Flow Control = FULL.\n"); + } else { + hw->fc.current_mode = ixgbe_fc_rx_pause; + hw_dbg(hw, "Flow Control=RX PAUSE frames only\n"); + } + } else if (!(adv_reg & adv_sym) && (adv_reg & adv_asm) && + (lp_reg & lp_sym) && (lp_reg & lp_asm)) { + hw->fc.current_mode = ixgbe_fc_tx_pause; + hw_dbg(hw, "Flow Control = TX PAUSE frames only.\n"); + } else if ((adv_reg & adv_sym) && (adv_reg & adv_asm) && + !(lp_reg & lp_sym) && (lp_reg & lp_asm)) { + hw->fc.current_mode = ixgbe_fc_rx_pause; + hw_dbg(hw, "Flow Control = RX PAUSE frames only.\n"); } else { - hw->fc.fc_was_autonegged = false; - hw->fc.current_mode = hw->fc.requested_mode; + hw->fc.current_mode = ixgbe_fc_none; + hw_dbg(hw, "Flow Control = NONE.\n"); } + return 0; } /** @@ -2202,241 +2394,63 @@ static s32 ixgbe_fc_autoneg_copper(struct ixgbe_hw *hw) } /** - * ixgbe_negotiate_fc - Negotiate flow control - * @hw: pointer to hardware structure - * @adv_reg: flow control advertised settings - * @lp_reg: link partner's flow control settings - * @adv_sym: symmetric pause bit in advertisement - * @adv_asm: asymmetric pause bit in advertisement - * @lp_sym: symmetric pause bit in link partner advertisement - * @lp_asm: asymmetric pause bit in link partner advertisement - * - * Find the intersection between advertised settings and link partner's - * advertised settings - **/ -static s32 ixgbe_negotiate_fc(struct ixgbe_hw *hw, u32 adv_reg, u32 lp_reg, - u32 adv_sym, u32 adv_asm, u32 lp_sym, u32 lp_asm) -{ - if ((!(adv_reg)) || (!(lp_reg))) - return IXGBE_ERR_FC_NOT_NEGOTIATED; - - if ((adv_reg & adv_sym) && (lp_reg & lp_sym)) { - /* - * Now we need to check if the user selected Rx ONLY - * of pause frames. In this case, we had to advertise - * FULL flow control because we could not advertise RX - * ONLY. Hence, we must now check to see if we need to - * turn OFF the TRANSMISSION of PAUSE frames. - */ - if (hw->fc.requested_mode == ixgbe_fc_full) { - hw->fc.current_mode = ixgbe_fc_full; - hw_dbg(hw, "Flow Control = FULL.\n"); - } else { - hw->fc.current_mode = ixgbe_fc_rx_pause; - hw_dbg(hw, "Flow Control=RX PAUSE frames only\n"); - } - } else if (!(adv_reg & adv_sym) && (adv_reg & adv_asm) && - (lp_reg & lp_sym) && (lp_reg & lp_asm)) { - hw->fc.current_mode = ixgbe_fc_tx_pause; - hw_dbg(hw, "Flow Control = TX PAUSE frames only.\n"); - } else if ((adv_reg & adv_sym) && (adv_reg & adv_asm) && - !(lp_reg & lp_sym) && (lp_reg & lp_asm)) { - hw->fc.current_mode = ixgbe_fc_rx_pause; - hw_dbg(hw, "Flow Control = RX PAUSE frames only.\n"); - } else { - hw->fc.current_mode = ixgbe_fc_none; - hw_dbg(hw, "Flow Control = NONE.\n"); - } - return 0; -} - -/** - * ixgbe_setup_fc - Set up flow control + * ixgbe_fc_autoneg - Configure flow control * @hw: pointer to hardware structure * - * Called at init time to set up flow control. + * Compares our advertised flow control capabilities to those advertised by + * our link partner, and determines the proper flow control mode to use. **/ -static s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num) +void ixgbe_fc_autoneg(struct ixgbe_hw *hw) { - s32 ret_val = 0; - u32 reg = 0, reg_bp = 0; - u16 reg_cu = 0; - -#ifdef CONFIG_DCB - if (hw->fc.requested_mode == ixgbe_fc_pfc) { - hw->fc.current_mode = hw->fc.requested_mode; - goto out; - } - -#endif /* CONFIG_DCB */ - /* Validate the packetbuf configuration */ - if (packetbuf_num < 0 || packetbuf_num > 7) { - hw_dbg(hw, "Invalid packet buffer number [%d], expected range " - "is 0-7\n", packetbuf_num); - ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS; - goto out; - } + s32 ret_val = IXGBE_ERR_FC_NOT_NEGOTIATED; + ixgbe_link_speed speed; + bool link_up; /* - * Validate the water mark configuration. Zero water marks are invalid - * because it causes the controller to just blast out fc packets. + * AN should have completed when the cable was plugged in. + * Look for reasons to bail out. Bail out if: + * - FC autoneg is disabled, or if + * - link is not up. + * + * Since we're being called from an LSC, link is already known to be up. + * So use link_up_wait_to_complete=false. */ - if (!hw->fc.low_water || - !hw->fc.high_water[packetbuf_num] || - !hw->fc.pause_time) { - hw_dbg(hw, "Invalid water mark configuration\n"); - ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS; + if (hw->fc.disable_fc_autoneg) goto out; - } - /* - * Validate the requested mode. Strict IEEE mode does not allow - * ixgbe_fc_rx_pause because it will cause us to fail at UNH. - */ - if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) { - hw_dbg(hw, "ixgbe_fc_rx_pause not valid in strict " - "IEEE mode\n"); - ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS; + hw->mac.ops.check_link(hw, &speed, &link_up, false); + if (!link_up) goto out; - } - - /* - * 10gig parts do not have a word in the EEPROM to determine the - * default flow control setting, so we explicitly set it to full. - */ - if (hw->fc.requested_mode == ixgbe_fc_default) - hw->fc.requested_mode = ixgbe_fc_full; - - /* - * Set up the 1G and 10G flow control advertisement registers so the - * HW will be able to do fc autoneg once the cable is plugged in. If - * we link at 10G, the 1G advertisement is harmless and vice versa. - */ switch (hw->phy.media_type) { + /* Autoneg flow control on fiber adapters */ case ixgbe_media_type_fiber: + if (speed == IXGBE_LINK_SPEED_1GB_FULL) + ret_val = ixgbe_fc_autoneg_fiber(hw); + break; + + /* Autoneg flow control on backplane adapters */ case ixgbe_media_type_backplane: - reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA); - reg_bp = IXGBE_READ_REG(hw, IXGBE_AUTOC); + ret_val = ixgbe_fc_autoneg_backplane(hw); break; + /* Autoneg flow control on copper adapters */ case ixgbe_media_type_copper: - hw->phy.ops.read_reg(hw, MDIO_AN_ADVERTISE, - MDIO_MMD_AN, ®_cu); + if (ixgbe_device_supports_autoneg_fc(hw) == 0) + ret_val = ixgbe_fc_autoneg_copper(hw); break; default: - ; - } - - /* - * The possible values of fc.requested_mode are: - * 0: Flow control is completely disabled - * 1: Rx flow control is enabled (we can receive pause frames, - * but not send pause frames). - * 2: Tx flow control is enabled (we can send pause frames but - * we do not support receiving pause frames). - * 3: Both Rx and Tx flow control (symmetric) are enabled. -#ifdef CONFIG_DCB - * 4: Priority Flow Control is enabled. -#endif - * other: Invalid. - */ - switch (hw->fc.requested_mode) { - case ixgbe_fc_none: - /* Flow control completely disabled by software override. */ - reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE); - if (hw->phy.media_type == ixgbe_media_type_backplane) - reg_bp &= ~(IXGBE_AUTOC_SYM_PAUSE | - IXGBE_AUTOC_ASM_PAUSE); - else if (hw->phy.media_type == ixgbe_media_type_copper) - reg_cu &= ~(IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE); - break; - case ixgbe_fc_rx_pause: - /* - * Rx Flow control is enabled and Tx Flow control is - * disabled by software override. Since there really - * isn't a way to advertise that we are capable of RX - * Pause ONLY, we will advertise that we support both - * symmetric and asymmetric Rx PAUSE. Later, we will - * disable the adapter's ability to send PAUSE frames. - */ - reg |= (IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE); - if (hw->phy.media_type == ixgbe_media_type_backplane) - reg_bp |= (IXGBE_AUTOC_SYM_PAUSE | - IXGBE_AUTOC_ASM_PAUSE); - else if (hw->phy.media_type == ixgbe_media_type_copper) - reg_cu |= (IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE); break; - case ixgbe_fc_tx_pause: - /* - * Tx Flow control is enabled, and Rx Flow control is - * disabled by software override. - */ - reg |= (IXGBE_PCS1GANA_ASM_PAUSE); - reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE); - if (hw->phy.media_type == ixgbe_media_type_backplane) { - reg_bp |= (IXGBE_AUTOC_ASM_PAUSE); - reg_bp &= ~(IXGBE_AUTOC_SYM_PAUSE); - } else if (hw->phy.media_type == ixgbe_media_type_copper) { - reg_cu |= (IXGBE_TAF_ASM_PAUSE); - reg_cu &= ~(IXGBE_TAF_SYM_PAUSE); - } - break; - case ixgbe_fc_full: - /* Flow control (both Rx and Tx) is enabled by SW override. */ - reg |= (IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE); - if (hw->phy.media_type == ixgbe_media_type_backplane) - reg_bp |= (IXGBE_AUTOC_SYM_PAUSE | - IXGBE_AUTOC_ASM_PAUSE); - else if (hw->phy.media_type == ixgbe_media_type_copper) - reg_cu |= (IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE); - break; -#ifdef CONFIG_DCB - case ixgbe_fc_pfc: - goto out; - break; -#endif /* CONFIG_DCB */ - default: - hw_dbg(hw, "Flow control param set incorrectly\n"); - ret_val = IXGBE_ERR_CONFIG; - goto out; - break; - } - - if (hw->mac.type != ixgbe_mac_X540) { - /* - * Enable auto-negotiation between the MAC & PHY; - * the MAC will advertise clause 37 flow control. - */ - IXGBE_WRITE_REG(hw, IXGBE_PCS1GANA, reg); - reg = IXGBE_READ_REG(hw, IXGBE_PCS1GLCTL); - - /* Disable AN timeout */ - if (hw->fc.strict_ieee) - reg &= ~IXGBE_PCS1GLCTL_AN_1G_TIMEOUT_EN; - - IXGBE_WRITE_REG(hw, IXGBE_PCS1GLCTL, reg); - hw_dbg(hw, "Set up FC; PCS1GLCTL = 0x%08X\n", reg); } - /* - * AUTOC restart handles negotiation of 1G and 10G on backplane - * and copper. There is no need to set the PCS1GCTL register. - * - */ - if (hw->phy.media_type == ixgbe_media_type_backplane) { - reg_bp |= IXGBE_AUTOC_AN_RESTART; - IXGBE_WRITE_REG(hw, IXGBE_AUTOC, reg_bp); - } else if ((hw->phy.media_type == ixgbe_media_type_copper) && - (ixgbe_device_supports_autoneg_fc(hw) == 0)) { - hw->phy.ops.write_reg(hw, MDIO_AN_ADVERTISE, - MDIO_MMD_AN, reg_cu); - } - - hw_dbg(hw, "Set up FC; IXGBE_AUTOC = 0x%08X\n", reg); out: - return ret_val; + if (ret_val == 0) { + hw->fc.fc_was_autonegged = true; + } else { + hw->fc.fc_was_autonegged = false; + hw->fc.current_mode = hw->fc.requested_mode; + } } /** @@ -3206,28 +3220,6 @@ wwn_prefix_out: return 0; } -/** - * ixgbe_device_supports_autoneg_fc - Check if phy supports autoneg flow - * control - * @hw: pointer to hardware structure - * - * There are several phys that do not support autoneg flow control. This - * function check the device id to see if the associated phy supports - * autoneg flow control. - **/ -static s32 ixgbe_device_supports_autoneg_fc(struct ixgbe_hw *hw) -{ - - switch (hw->device_id) { - case IXGBE_DEV_ID_X540T: - return 0; - case IXGBE_DEV_ID_82599_T3_LOM: - return 0; - default: - return IXGBE_ERR_FC_NOT_SUPPORTED; - } -} - /** * ixgbe_set_mac_anti_spoofing - Enable/Disable MAC anti-spoofing * @hw: pointer to hardware structure