From: Priit Laes Date: Fri, 8 Jan 2021 11:28:47 +0000 (+0200) Subject: ath79: add support for COMFAST CF-E355AC v2 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=66d2d037ad40dec2653c7c57946215860352423f;p=openwrt%2Fstaging%2Fansuel.git ath79: add support for COMFAST CF-E355AC v2 COMFAST CF-E355AC v2 is a ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9531 + QCA9886. Short specification: - 1x 10/100 Mbps Ethernet, with PoE support (wan/eth1) - 1x 10/100/1000 Mbps Ethernet, with PoE support (lan/eth0) - 128MB of RAM (DDR2) - 16 MB of FLASH - 2T2R 2.4 GHz, 802.11b/g/n (wlan2g) - 2T2R 5 GHz, 802.11ac/n/a, WAVE 2 (wlan5g) - built-in 4x 3 dBi antennas - output power (max): 500 mW (27 dBm) - 1x RGB LED, 1x button - separate watchdog chip via GPIO (bottom of PCB?) - UART header on PCB with proper labelling Markings on PCB: * R121QH_VER2.1 (silkscreen, bottom) * CF-WA800 (sticker, top) Initial flashing instructions: Original firmware is based on OpenWrt. a) Use sysupgrade image directly in vendor GUI. b) Or via tftp: ipaddr=192.168.1.1 serverip=192.168.1.10 bootfile="firmware.bin" c) Or possibly via u-boot's `httpd` command. MAC-address mapping follows original firmware: * eth1 (wan) is the lowest mac address (art @ 0x0) * eth0 (lan) uses eth1 + 1 (art @ 0x1002) * wlan2g (phy1) uses eth1 + 2 (art @ 0x06) * wlan5g (phy0) uses eth1 + 10 (not present in art) * unused MAC (eth1 + 3) (art @ 0x5006) Art dump (`hexdump /dev/mtd1 |grep ZZZZ`): 0000000 ZZZZ XXXX XXX0 ZZZZ XXXX XXX2 ffff ffff 0001000 0202 ZZZZ XXXX XXX1 0000 0000 0000 0000 0005000 202f bd21 0101 ZZZZ XXXX XXX3 0000 2000 Root access to original firmware (only via UART) can be achieved by making a backup of configuration from web interface. Backup contains whole `/etc` directory... Signed-off-by: Priit Laes Link: https://github.com/openwrt/openwrt/pull/16556 Signed-off-by: Hauke Mehrtens --- diff --git a/target/linux/ath79/dts/qca9531_comfast_cf-e355ac-v2.dts b/target/linux/ath79/dts/qca9531_comfast_cf-e355ac-v2.dts new file mode 100644 index 0000000000..81c0af19a5 --- /dev/null +++ b/target/linux/ath79/dts/qca9531_comfast_cf-e355ac-v2.dts @@ -0,0 +1,161 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qca953x.dtsi" + +#include +#include +#include + +/ { + compatible = "comfast,cf-e355ac-v2", "qca,qca9531"; + model = "COMFAST CF-E355AC V2"; + + aliases { + serial0 = &uart; + led-boot = &led_lan; + led-failsafe = &led_lan; + led-upgrade = &led_lan; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + linux,code = ; + gpios = <&gpio 17 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + }; + + leds { + /* Single RGB led controlled via GPIO */ + compatible = "gpio-leds"; + + pinctrl-names = "default"; + pinctrl-0 = <&jtag_disable_pins>; + + led_lan: lan { + color = ; + function = LED_FUNCTION_LAN; + gpios = <&gpio 3 GPIO_ACTIVE_LOW>; + }; + + wlan2g { + color = ; + function = "LED_FUNCTION_WLAN_2GHZ"; + gpios = <&gpio 0 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy1tpt"; + }; + + wlan5g { + color = ; + function = "LED_FUNCTION_WLAN_5GHZ"; + gpios = <&gpio 2 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy0tpt"; + }; + }; + + watchdog { + compatible = "linux,wdt-gpio"; + gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + hw_algo = "toggle"; + hw_margin_ms = <1200>; + always-running; + }; +}; + +ð0 { + status = "okay"; + phy-handle = <&swphy4>; + + nvmem-cells = <&macaddr_art_0 0>; + nvmem-cell-names = "mac-address"; +}; + +ð1 { + nvmem-cells = <&macaddr_art_0 1>; + nvmem-cell-names = "mac-address"; +}; + +&pcie0 { + status = "okay"; + + wifi@0,0 { + compatible = "qcom,ath10k"; + reg = <0x0000 0 0 0 0>; + nvmem-cells = <&precal_art_5000>, <&macaddr_art_0 10>; + nvmem-cell-names = "pre-calibration", "mac-address"; + }; +}; + +&spi { + status = "okay"; + + flash@0 { + compatible = "winbond,w25q128", "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x000000 0x010000>; + read-only; + }; + + partition@10000 { + label = "art"; + reg = <0x010000 0x010000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_art_0: macaddr@0 { + compatible = "mac-base"; + reg = <0x0 0x6>; + #nvmem-cell-cells = <1>; + }; + + cal_art_1000: calibration@1000 { + reg = <0x1000 0x440>; + }; + + precal_art_5000: pre-calibration@5000 { + reg = <0x5000 0x2f20>; + }; + }; + }; + + partition@20000 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0x020000 0xfd0000>; + }; + + partition@ff0000 { + label = "nvram"; + reg = <0xff0000 0x010000>; + read-only; + }; + }; + }; +}; + +&wdt { + status = "disabled"; +}; + +&wmac { + status = "okay"; + + nvmem-cells = <&cal_art_1000>, <&macaddr_art_0 2>; + nvmem-cell-names = "calibration", "mac-address"; +}; diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index 5990f9f177..06448f2172 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -799,6 +799,17 @@ define Device/comfast_cf-e314n-v2 endef TARGET_DEVICES += comfast_cf-e314n-v2 +define Device/comfast_cf-e355ac-v2 + SOC := qca9531 + DEVICE_VENDOR := COMFAST + DEVICE_MODEL := CF-E355AC + DEVICE_VARIANT := v2 + DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct \ + -swconfig -uboot-envtools + IMAGE_SIZE := 16192k +endef +TARGET_DEVICES += comfast_cf-e355ac-v2 + define Device/comfast_cf-e375ac SOC := qca9563 DEVICE_VENDOR := COMFAST