From: Piotr Dymacz Date: Fri, 9 Oct 2020 05:30:24 +0000 (+0200) Subject: ath79: add support for ALFA Network Pi-WiFi4 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=64a6f4a9c1553a968969fb8821f558c875187acc;p=openwrt%2Fstaging%2Frobimarko.git ath79: add support for ALFA Network Pi-WiFi4 ALFA Network Pi-WiFi4 is a Qualcomm QCA9531 v2 based, high-power 802.11n WiFi board in Raspberry Pi 3B shape, equipped with 1x FE and 4x USB 2.0. Specifications: - Qualcomm/Atheros QCA9531 v2 - 650/400/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16+ MB of flash (SPI NOR) - 1x 10/100 Mbps Ethernet - 2T2R 2.4 GHz Wi-Fi with Qorvo RFFM8228P FEM - 2x IPEX/U.FL connectors on PCB - 4x USB 2.0 Type-A - Genesys Logic GL850G 4-port USB HUB - USB power is controlled by GPIO - 5x LED (3x on PCB, 2x in RJ45, 4x driven by GPIO) - 1x button (reset) - external h/w watchdog (EM6324QYSP5B, enabled by default) - 1x micro USB Type-B for power and system console (Holtek HT42B534) - UART and GPIO (8-pin, 1.27 mm pitch) header on PCB Flash instruction: You can use sysupgrade image directly in vendor firmware which is based on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot: 1. Configure PC with static IP 192.168.1.2/24. 2. Connect PC with one of RJ45 ports, press the reset button, power up device, wait for first blink of all LEDs (indicates network setup), then keep button for 3 following blinks and release it. 3. Open 192.168.1.1 address in your browser and upload sysupgrade image. Signed-off-by: Piotr Dymacz --- diff --git a/target/linux/ath79/dts/qca9531_alfa-network_pi-wifi4.dts b/target/linux/ath79/dts/qca9531_alfa-network_pi-wifi4.dts new file mode 100644 index 0000000000..42f2c9ffe5 --- /dev/null +++ b/target/linux/ath79/dts/qca9531_alfa-network_pi-wifi4.dts @@ -0,0 +1,87 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qca9531_alfa-network_r36a.dtsi" + +/ { + model = "ALFA Network Pi-WiFi4"; + compatible = "alfa-network,pi-wifi4", "qca,qca9531"; + + aliases { + led-boot = &led_usb; + led-failsafe = &led_usb; + led-upgrade = &led_usb; + }; + + leds { + compatible = "gpio-leds"; + + pinctrl-names = "default"; + pinctrl-0 = <&enable_gpio4 &enable_gpio16>; + + lan_data { + label = "orange:lan_data"; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + }; + + lan_link { + label = "green:lan_link"; + gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + }; + + led_usb: usb { + label = "green:usb"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + linux,default-trigger = "usbport"; + trigger-sources = <&gl850g_port1>, <&gl850g_port2>, + <&gl850g_port3>, <&gl850g_port4>; + }; + + wlan { + label = "blue:wlan"; + gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + }; +}; + +ð0 { + mtd-mac-address = <&art 0x1002>; + mtd-mac-address-increment = <(-1)>; +}; + +ð1 { + compatible = "syscon", "simple-mfd"; +}; + +&gpio_export { + usb-power { + gpio-export,name = "usb-power"; + gpio-export,output = <1>; + gpios = <&gpio 3 GPIO_ACTIVE_HIGH>; + }; +}; + +&hub_port0 { + #address-cells = <1>; + #size-cells = <0>; + + gl850g_port1: port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; + + gl850g_port2: port@2 { + reg = <2>; + #trigger-source-cells = <0>; + }; + + gl850g_port3: port@3 { + reg = <3>; + #trigger-source-cells = <0>; + }; + + gl850g_port4: port@4 { + reg = <4>; + #trigger-source-cells = <0>; + }; +}; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds index 08ca2a8398..a345dca4af 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds @@ -40,6 +40,10 @@ alfa-network,n5q) ucidef_set_led_rssi "signal3" "SIGNAL3" "green:signal3" "wlan0" "50" "100" ucidef_set_led_rssi "signal4" "SIGNAL4" "green:signal4" "wlan0" "75" "100" ;; +alfa-network,pi-wifi4) + ucidef_set_led_netdev "lan_data" "LAN_DATA" "orange:lan_data" "eth0" "tx rx" + ucidef_set_led_netdev "lan_link" "LAN_LINK" "green:lan_link" "eth0" "link" + ;; alfa-network,r36a) ucidef_set_led_netdev "lan" "LAN" "blue:lan" "eth0" ucidef_set_led_switch "wan" "WAN" "blue:wan" "switch0" "0x10" diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index 4d0766d262..d03399a054 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -13,6 +13,7 @@ ath79_setup_interfaces() adtran,bsap1840|\ allnet,all-wap02860ac|\ alfa-network,ap121f|\ + alfa-network,pi-wifi4|\ arduino,yun|\ aruba,ap-105|\ avm,fritz1750e|\ @@ -418,6 +419,7 @@ ath79_setup_macs() alfa-network,ap121fe|\ alfa-network,n2q|\ alfa-network,n5q|\ + alfa-network,pi-wifi4|\ alfa-network,r36a|\ engenius,ens202ext-v1) label_mac=$(mtd_get_mac_binary art 0x1002) diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index dc91e1b6d9..fc8b136c51 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -257,6 +257,15 @@ define Device/alfa-network_n5q endef TARGET_DEVICES += alfa-network_n5q +define Device/alfa-network_pi-wifi4 + SOC := qca9531 + DEVICE_VENDOR := ALFA Network + DEVICE_MODEL := Pi-WiFi4 + DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport -swconfig + IMAGE_SIZE := 15872k +endef +TARGET_DEVICES += alfa-network_pi-wifi4 + define Device/alfa-network_r36a SOC := qca9531 DEVICE_VENDOR := ALFA Network