From: Chukun Pan Date: Fri, 16 Jun 2023 15:16:30 +0000 (+0800) Subject: mediatek: filogic: add JCG Q30 PRO support X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=626344c9926dcf2db2e10681c19aab0328fee160;p=openwrt%2Fstaging%2Fnbd.git mediatek: filogic: add JCG Q30 PRO support Hardware specification: SoC: MediaTek MT7981B 2x A53 Flash: Winbond 128MB RAM: DDR3 256MB Ethernet: 4x 10/100/1000 Mbps Switch: MediaTek MT7531AE WiFi: MediaTek MT7976C Button: Reset Power: DC 12V 1A Flash instructions: 1. Connect to your PC via the Gigabit port of the router, set a static ip on the ethernet interface of your PC. (ip 192.168.1.254, gateway 192.168.1.1) 2. Attach UART, pause at u-boot menu. 3. Select "Upgrade ATF BL2", then use preloader.bin 4. Select "Upgrade ATF FIP", then use bl31-uboot.fip 5. Download the initramfs image, and type "reset", waiting for tftp recovery to complete. 6. After openwrt boots up, perform sysupgrade. Note: 1. Since NMBM is disabled, we must back up all partitions. 2. Although we can upgrade new firmware in the stock firmware, we need the special fit image signature of MediaTek and dual boot (hack kernel) to make u-boot boot it. So just abandon these hacks and flash it via the serial port. Signed-off-by: Chukun Pan --- diff --git a/target/linux/mediatek/dts/mt7981b-jcg-q30-pro.dts b/target/linux/mediatek/dts/mt7981b-jcg-q30-pro.dts new file mode 100644 index 0000000000..adb86d9ebd --- /dev/null +++ b/target/linux/mediatek/dts/mt7981b-jcg-q30-pro.dts @@ -0,0 +1,225 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +/dts-v1/; +#include +#include + +#include "mt7981.dtsi" + +/ { + model = "JCG Q30 PRO"; + compatible = "jcg,q30-pro", "mediatek,mt7981"; + + aliases { + serial0 = &uart0; + label-mac-device = &gmac0; + led-boot = &led_status_red; + led-failsafe = &led_status_red; + led-running = &led_status_blue; + led-upgrade = &led_status_blue; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory { + reg = <0 0x40000000 0 0x10000000>; + }; + + gpio-keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + linux,code = ; + gpios = <&pio 1 GPIO_ACTIVE_LOW>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_status_red: red { + label = "red:status"; + gpios = <&pio 8 GPIO_ACTIVE_HIGH>; + }; + + led_status_blue: blue { + label = "blue:status"; + gpios = <&pio 13 GPIO_ACTIVE_LOW>; + }; + }; +}; + +ð { + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "2500base-x"; + + nvmem-cells = <&macaddr_lan>; + nvmem-cell-names = "mac-address"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; +}; + +&mdio_bus { + switch: switch@0 { + compatible = "mediatek,mt7531"; + reg = <31>; + reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&pio>; + interrupts = <38 IRQ_TYPE_LEVEL_HIGH>; + }; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_flash_pins>; + status = "okay"; + + spi_nand@0 { + compatible = "spi-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + + spi-max-frequency = <52000000>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "bl2"; + reg = <0x0000000 0x0100000>; + read-only; + }; + + partition@100000 { + label = "u-boot-env"; + reg = <0x0100000 0x0080000>; + }; + + factory: partition@180000 { + label = "Factory"; + reg = <0x0180000 0x0200000>; + read-only; + }; + + partition@380000 { + label = "fip"; + reg = <0x0380000 0x0200000>; + read-only; + }; + + partition@580000 { + label = "ubi"; + reg = <0x0580000 0x7000000>; + }; + }; + }; +}; + +&switch { + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "wan"; + nvmem-cells = <&macaddr_wan>; + nvmem-cell-names = "mac-address"; + }; + + port@1 { + reg = <1>; + label = "lan1"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan3"; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; +}; + +&pio { + spi0_flash_pins: spi0-pins { + mux { + function = "spi"; + groups = "spi0", "spi0_wp_hold"; + }; + + conf-pu { + pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP"; + drive-strength = <8>; + mediatek,pull-up-adv = <0>; /* bias-disable */ + }; + + conf-pd { + pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO"; + drive-strength = <8>; + mediatek,pull-up-adv = <0>; /* bias-disable */ + }; + }; +}; + +&uart0 { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +&wifi { + status = "okay"; + + mediatek,mtd-eeprom = <&factory 0x0>; +}; + +&factory { + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_wan: macaddr@a0024 { + reg = <0xa0024 0x6>; + }; + + macaddr_lan: macaddr@a002a { + reg = <0xa002a 0x6>; + }; +}; diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network index aad1d67ff6..0760d17a8e 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network @@ -49,6 +49,7 @@ mediatek_setup_interfaces() ucidef_set_interfaces_lan_wan "lan0 lan1 lan2" eth1 ;; cetron,ct3003|\ + jcg,q30-pro|\ qihoo,360t7) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" wan ;; diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac index 395cc0f2dc..a9de563a4b 100644 --- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac +++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac @@ -65,6 +65,11 @@ case "$board" in [ "$PHYNBR" = "0" ] && macaddr_add $addr 2 > /sys${DEVPATH}/macaddress [ "$PHYNBR" = "1" ] && macaddr_add $addr 3 > /sys${DEVPATH}/macaddress ;; + jcg,q30-pro) + # Originally, phy1 is phy0 mac with LA bit set. However, this would conflict + # addresses on multiple VIFs with the other radio. Use label mac to set LA bit. + [ "$PHYNBR" = "1" ] && macaddr_setbit_la $(get_mac_label) > /sys${DEVPATH}/macaddress + ;; mercusys,mr90x-v1) addr=$(get_mac_binary "/tmp/tp_data/default-mac" 0) [ "$PHYNBR" = "0" ] && echo "$addr" > /sys${DEVPATH}/macaddress diff --git a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh index b7b9d65993..cef1131ddb 100755 --- a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh +++ b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh @@ -112,6 +112,7 @@ platform_do_upgrade() { emmc_do_upgrade "$1" ;; h3c,magic-nx30-pro|\ + jcg,q30-pro|\ mediatek,mt7981-rfb|\ qihoo,360t7|\ tplink,tl-xdr4288|\ diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk index 0ef3e94575..4d4f3b62a2 100644 --- a/target/linux/mediatek/image/filogic.mk +++ b/target/linux/mediatek/image/filogic.mk @@ -330,6 +330,30 @@ define Device/h3c_magic-nx30-pro endef TARGET_DEVICES += h3c_magic-nx30-pro +define Device/jcg_q30-pro + DEVICE_VENDOR := JCG + DEVICE_MODEL := Q30 PRO + DEVICE_DTS := mt7981b-jcg-q30-pro + DEVICE_DTS_DIR := ../dts + UBINIZE_OPTS := -E 5 + BLOCKSIZE := 128k + PAGESIZE := 2048 + KERNEL_IN_UBI := 1 + UBOOTENV_IN_UBI := 1 + IMAGES := sysupgrade.itb + KERNEL_INITRAMFS_SUFFIX := -recovery.itb + KERNEL := kernel-bin | gzip + KERNEL_INITRAMFS := kernel-bin | lzma | \ + fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k + IMAGE/sysupgrade.itb := append-kernel | \ + fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | append-metadata + DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware + ARTIFACTS := preloader.bin bl31-uboot.fip + ARTIFACT/preloader.bin := mt7981-bl2 spim-nand-ddr3 + ARTIFACT/bl31-uboot.fip := mt7981-bl31-uboot jcg_q30-pro +endef +TARGET_DEVICES += jcg_q30-pro + define Device/netgear_wax220 DEVICE_VENDOR := NETGEAR DEVICE_MODEL := WAX220