From: INAGAKI Hiroshi Date: Fri, 23 Apr 2021 09:32:11 +0000 (+0900) Subject: mediatek: mt7622: add support for ELECOM WRC-X3200GST3 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=58b3b557b629f6a2046414e0e1b39189d918133f;p=openwrt%2Fstaging%2Fdangole.git mediatek: mt7622: add support for ELECOM WRC-X3200GST3 ELECOM WRC-X3200GST3 is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on MT7622B. Specifications: - SoC : MediaTek MT7622B - RAM : DDR3 512 MiB (Nanya NT5CC256M16ER-EK) - Flash : SPI-NAND 128 MiB (Winbond W25N01GVZEIG) - WLAN : 2.4/5 GHz 4T4R - 2.4 GHz : MediaTek MT7622B (SoC) - 5 GHz : MediaTek MT7915A - Ethernet : 5x 10/100/1000 Mbps - Switch : MediaTek MT7531 - LEDs/Keys : 6x/4x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J19: 3.3V, GND, TX, RX from power jack side - 115200n8 - Power : 12 VDC, 1.5 A Flash instruction using factory image: 1. Boot WRC-X3200GST3 normally with "Router" mode 2. Access to "http://192.168.2.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click apply ("適用") button 4. Wait ~120 seconds to complete flashing MAC Addresses: LAN : 04:AB:18:xx:xx:77 (Factory, 0x7FFF4 (hex)) WAN : 04:AB:18:xx:xx:78 (Factory, 0x7FFFA (hex)) 2.4 GHz: 04:AB:18:xx:xx:79 (Factory, 0x4 (hex)) 5 GHz : 04:AB:18:xx:xx:7A (none) Note: - currently, there is no "phy1tpt" trigger for 5 GHz wlan (MT7915) in "trigger" file of LEDs, use "phy1radio" trigger instead Signed-off-by: INAGAKI Hiroshi --- diff --git a/target/linux/mediatek/dts/mt7622-elecom-wrc-x3200gst3.dts b/target/linux/mediatek/dts/mt7622-elecom-wrc-x3200gst3.dts new file mode 100644 index 0000000000..fdbcbc18bc --- /dev/null +++ b/target/linux/mediatek/dts/mt7622-elecom-wrc-x3200gst3.dts @@ -0,0 +1,436 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include +#include +#include + +#include "mt7622.dtsi" +#include "mt6380.dtsi" + +/ { + model = "ELECOM WRC-X3200GST3"; + compatible = "elecom,wrc-x3200gst3", "mediatek,mt7622"; + + aliases { + serial0 = &uart0; + led-boot = &led_power_green; + led-failsafe = &led_power_red; + led-running = &led_power_green; + led-upgrade = &led_power_green; + label-mac-device = &wan; + }; + + chosen { + bootargs = "earlycon=uart8250,mmio32,0x11002000 console=ttyS0,115200n8 swiotlb=512"; + }; + + memory { + reg = <0 0x40000000 0 0x1f000000>; + }; + + leds { + compatible = "gpio-leds"; + + led-0 { + label = "red:wps"; + gpios = <&pio 47 GPIO_ACTIVE_HIGH>; + color = ; + function = LED_FUNCTION_WPS; + }; + + led_power_red: led-1 { + label = "red:power"; + gpios = <&pio 48 GPIO_ACTIVE_HIGH>; + color = ; + function = LED_FUNCTION_POWER; + function-enumerator = <1>; + }; + + led_power_green: led-2 { + label = "green:power"; + gpios = <&pio 49 GPIO_ACTIVE_HIGH>; + color = ; + function = LED_FUNCTION_POWER; + function-enumerator = <2>; + }; + + led-3 { + label = "blue:power"; + gpios = <&pio 50 GPIO_ACTIVE_HIGH>; + color = ; + function = LED_FUNCTION_POWER; + function-enumerator = <3>; + }; + + led-4 { + label = "white:wlan2g"; + gpios = <&pio 85 GPIO_ACTIVE_HIGH>; + color = ; + function = LED_FUNCTION_WLAN; + function-enumerator = <1>; + linux,default-trigger = "phy0tpt"; + }; + + led-5 { + label = "white:wlan5g"; + gpios = <&pio 89 GPIO_ACTIVE_HIGH>; + color = ; + function = LED_FUNCTION_WLAN; + function-enumerator = <2>; + linux,default-trigger = "phy1radio"; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&pio 0 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + ap { + label = "ap"; + gpios = <&pio 42 GPIO_ACTIVE_LOW>; + linux,code = ; + linux,input-type = ; + }; + + router { + label = "router"; + gpios = <&pio 43 GPIO_ACTIVE_LOW>; + linux,code = ; + linux,input-type = ; + }; + + wps { + label = "wps"; + gpios = <&pio 102 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; +}; + +&cpu0 { + proc-supply = <&mt6380_vcpu_reg>; + sram-supply = <&mt6380_vm_reg>; +}; + +&cpu1 { + proc-supply = <&mt6380_vcpu_reg>; + sram-supply = <&mt6380_vm_reg>; +}; + +&pio { + eth_pins: eth-pins { + mux { + function = "eth"; + groups = "mdc_mdio", "rgmii_via_gmac2"; + }; + }; + + pcie0_pins: pcie0-pins { + mux { + function = "pcie"; + groups = "pcie0_pad_perst", + "pcie0_1_waken", + "pcie0_1_clkreq"; + }; + }; + + pmic_bus_pins: pmic-bus-pins { + mux { + function = "pmic"; + groups = "pmic_bus"; + }; + }; + + pwm7_pins: pwm1-2-pins { + mux { + function = "pwm"; + groups = "pwm_ch7_2"; + }; + }; + + /* Serial NAND is shared pin with SPI-NOR */ + serial_nand_pins: serial-nand-pins { + mux { + function = "flash"; + groups = "snfi"; + }; + + conf-cmd-data { + pins = "SPI_WP", "SPI_HOLD", "SPI_MOSI", + "SPI_MISO", "SPI_CS"; + drive-strength = <16>; + bias-pull-up; + }; + + conf-clk { + pins = "SPI_CLK"; + drive-strength = <16>; + bias-pull-down; + }; + }; + + uart0_pins: uart0-pins { + mux { + function = "uart"; + groups = "uart0_0_tx_rx" ; + }; + }; + + watchdog_pins: watchdog-pins { + mux { + function = "watchdog"; + groups = "watchdog"; + }; + }; +}; + +ð { + pinctrl-names = "default"; + pinctrl-0 = <ð_pins>; + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + + phy-connection-type = "2500base-x"; + + nvmem-cells = <&macaddr_factory_7fff4>; + nvmem-cell-names = "mac-address"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + + mdio-bus { + #address-cells = <1>; + #size-cells = <0>; + + switch@0 { + compatible = "mediatek,mt7531"; + reg = <0>; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&pio>; + interrupts = <53 IRQ_TYPE_LEVEL_HIGH>; + reset-gpios = <&pio 54 GPIO_ACTIVE_HIGH>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + wan: port@0 { + reg = <0>; + label = "wan"; + + nvmem-cells = <&macaddr_factory_7fffa>; + nvmem-cell-names = "mac-address"; + }; + + port@1 { + reg = <1>; + label = "lan4"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@3 { + reg = <3>; + label = "lan2"; + }; + + port@4 { + reg = <4>; + label = "lan1"; + }; + + port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; + }; + }; +}; + +&bch { + status = "okay"; +}; + +&snfi { + pinctrl-names = "default"; + pinctrl-0 = <&serial_nand_pins>; + status = "okay"; + + flash@0 { + compatible = "spi-nand"; + reg = <0>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + nand-ecc-engine = <&snfi>; + mediatek,bmt-v2; + mediatek,bmt-table-size = <0x1000>; + mediatek,bmt-remap-range = <0x0 0x8c0000>, + <0x1bc0000 0x30c0000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "Preloader"; + reg = <0x0 0x80000>; + read-only; + }; + + partition@80000 { + label = "ATF"; + reg = <0x80000 0x40000>; + read-only; + }; + + partition@c0000 { + label = "u-boot"; + reg = <0xc0000 0x80000>; + read-only; + }; + + partition@140000 { + label = "u-boot-env"; + reg = <0x140000 0x80000>; + read-only; + }; + + factory: partition@1c0000 { + label = "factory"; + reg = <0x1c0000 0x100000>; + read-only; + + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_factory_4: macaddr@4 { + reg = <0x4 0x6>; + }; + + macaddr_factory_7fff4: macaddr@7fff4 { + reg = <0x7fff4 0x6>; + }; + + macaddr_factory_7fffa: macaddr@7fffa { + reg = <0x7fffa 0x6>; + }; + }; + + partition@2c0000 { + label = "kernel"; + reg = <0x2c0000 0x600000>; + }; + + partition@8c0000 { + label = "ubi"; + reg = <0x8c0000 0x1300000>; + }; + + partition@1bc0000 { + label = "tm_pattern"; + reg = <0x1bc0000 0x500000>; + read-only; + }; + + partition@20c0000 { + label = "tm_key"; + reg = <0x20c0000 0x100000>; + read-only; + }; + + partition@21c0000 { + label = "user_data"; + reg = <0x21c0000 0xf00000>; + read-only; + }; + + partition@30c0000 { + label = "reserved"; + reg = <0x30c0000 0x4f40000>; + read-only; + }; + }; + }; +}; + +&pcie0 { + pinctrl-names = "default"; + pinctrl-0 = <&pcie0_pins>; + status = "okay"; +}; + +&slot0 { + status = "okay"; + + wifi@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0000 0 0 0 0>; + mediatek,mtd-eeprom = <&factory 0x5000>; + ieee80211-freq-limit = <5000000 6000000>; + nvmem-cells = <&macaddr_factory_4>; + nvmem-cell-names = "mac-address"; + mac-address-increment = <1>; + }; +}; + +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm7_pins>; + status = "okay"; +}; + +&pwrap { + pinctrl-names = "default"; + pinctrl-0 = <&pmic_bus_pins>; + status = "okay"; +}; + +&rtc { + status = "disabled"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins>; + status = "okay"; +}; + +&watchdog { + pinctrl-names = "default"; + pinctrl-0 = <&watchdog_pins>; + status = "okay"; +}; + +&wmac { + status = "okay"; + + mediatek,mtd-eeprom = <&factory 0x0>; +}; diff --git a/target/linux/mediatek/image/mt7622.mk b/target/linux/mediatek/image/mt7622.mk index 39bc7bc2ea..aba8bdfe0b 100644 --- a/target/linux/mediatek/image/mt7622.mk +++ b/target/linux/mediatek/image/mt7622.mk @@ -137,6 +137,26 @@ define Device/elecom_wrc-2533gent endef TARGET_DEVICES += elecom_wrc-2533gent +define Device/elecom_wrc-x3200gst3 + DEVICE_VENDOR := ELECOM + DEVICE_MODEL := WRC-X3200GST3 + DEVICE_DTS := mt7622-elecom-wrc-x3200gst3 + DEVICE_DTS_DIR := ../dts + IMAGE_SIZE := 25600k + KERNEL_SIZE := 6144k + BLOCKSIZE := 128k + PAGESIZE := 2048 + UBINIZE_OPTS := -E 5 + IMAGES += factory.bin + IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | \ + append-ubi | check-size | \ + elecom-wrc-gs-factory WRC-X3200GST3 0.00 -N | \ + append-string MT7622_ELECOM_WRC-X3200GST3 + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata + DEVICE_PACKAGES := kmod-mt7915e +endef +TARGET_DEVICES += elecom_wrc-x3200gst3 + define Device/linksys_e8450 DEVICE_VENDOR := Linksys DEVICE_MODEL := E8450 diff --git a/target/linux/mediatek/mt7622/base-files/etc/board.d/02_network b/target/linux/mediatek/mt7622/base-files/etc/board.d/02_network index c55fcbee2e..29f4b875f8 100644 --- a/target/linux/mediatek/mt7622/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/mt7622/base-files/etc/board.d/02_network @@ -9,6 +9,7 @@ mediatek_setup_interfaces() case $board in bananapi,bpi-r64|\ + elecom,wrc-x3200gst3|\ linksys,e8450|\ linksys,e8450-ubi|\ mediatek,mt7622-rfb1|\ diff --git a/target/linux/mediatek/mt7622/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/mt7622/base-files/lib/upgrade/platform.sh index f54665dfa1..1036793145 100755 --- a/target/linux/mediatek/mt7622/base-files/lib/upgrade/platform.sh +++ b/target/linux/mediatek/mt7622/base-files/lib/upgrade/platform.sh @@ -32,6 +32,12 @@ platform_do_upgrade() { nand_do_upgrade "$1" fi ;; + elecom,wrc-x3200gst3|\ + mediatek,mt7622-rfb1-ubi|\ + totolink,a8000ru|\ + xiaomi,redmi-router-ax6s) + nand_do_upgrade "$1" + ;; linksys,e8450-ubi) CI_KERNPART="fit" nand_do_upgrade "$1" @@ -44,11 +50,6 @@ platform_do_upgrade() { fi default_do_upgrade "$1" ;; - mediatek,mt7622-rfb1-ubi|\ - totolink,a8000ru|\ - xiaomi,redmi-router-ax6s) - nand_do_upgrade "$1" - ;; *) default_do_upgrade "$1" ;; @@ -67,6 +68,7 @@ platform_check_image() { buffalo,wsr-2533dhp2) buffalo_check_image "$board" "$magic" "$1" || return 1 ;; + elecom,wrc-x3200gst3|\ mediatek,mt7622-rfb1-ubi|\ totolink,a8000ru|\ xiaomi,redmi-router-ax6s)