From: Martin Kennedy Date: Sat, 28 Nov 2020 02:03:32 +0000 (+0000) Subject: ath79: add support for Meraki MR12 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=55d2db0e8cebca5aa9739c4db875ef57c4643f6d;p=openwrt%2Fstaging%2Fnbd.git ath79: add support for Meraki MR12 Port device support for Meraki MR12 from the ar71xx target to ath79. Specifications: - SoC: AR7242-AH1A CPU - RAM: 64MiB (NANYA NT5DS32M16DS-5T) - NOR Flash: 16MiB (MXIC MX25L12845EMI-10G) - Ethernet: 1 x PoE Gigabit Ethernet Port (SoC MAC + AR8021-BL1E PHY) - Ethernet: 1 x 100Mbit port (SoC MAC+PHY) - Wi-Fi: Atheros AR9283-AL1A (2T2R, 11n) Installation: 1. Requires TFTP server at 192.168.1.101, w/ initramfs & sysupgrade .bins 2. Open shell case 3. Connect a USB->TTL cable to headers furthest from the RF shield 4. Power on the router; connect to U-boot over 115200-baud connection 5. Interrupt U-boot process to boot Openwrt by running: setenv bootcmd bootm 0xbf0a0000; saveenv; tftpboot 0c00000 .bin; bootm 0c00000; 6. Copy sysupgrade image to /tmp on MR12 7. sysupgrade /tmp/.bin Notes: - kmod-owl-loader is still required to load the ART partition into the driver. - The manner of storing MAC addresses is updated from ar71xx; it is at 0x66 of the 'config' partition, where it was discovered that the OEM firmware stores it. This is set as read-only. If you are migrating from ar71xx and used the method mentioned above to upgrade, use kmod-mtd-rw or UCI to add the MAC back in. One more method for doing this is described below. - Migrating directly from ar71xx has not been thoroughly tested, but one method has been used a couple of times with good success, migrating 18.06.2 to a full image produced as of this commit. Please note that these instructions are only for experienced users, and/or those still able to open their device up to flash it via the serial headers should anything go wrong. 1) Install kmod-mtd-rw and uboot-envtools 2) Run `insmod mtd-rw.ko i_want_a_brick=1` 3) Modify /etc/fw_env.config to point to the u-boot-env partition. The file /etc/fw_env.config should contain: # MTD device env offset env size sector size /dev/mtd1 0x00000 0x10000 0x10000 See https://openwrt.org/docs/techref/bootloader/uboot.config for more details. 4) Run `fw_printenv` to verify everything is correct, as per the link above. 5) Run `fw_setenv bootcmd bootm 0xbf0a0000` to set a new boot address. 6) Manually modify /lib/upgrade/common.sh's get_image function: Change ... cat "$from" 2>/dev/null | $cmd ... into ... ( dd if=/dev/zero bs=1 count=$((0x66)) ; # Pad the first 102 bytes echo -ne '\x00\x18\x0a\x12\x34\x56' ; # Add in MAC address dd if=/dev/zero bs=1 count=$((0x20000-0x66-0x6)) ; # Pad the rest cat "$from" 2>/dev/null ) | $cmd ... which, during the upgrade process, will pad the image by 128K of zeroes-plus-MAC-address, in order for the ar71xx's firmware partition -- which starts at 0xbf080000 -- to be instead aligned with the ath79 firmware partition, which starts 128K later at 0xbf0a0000. 7) Copy the sysupgrade image into /tmp, as above 8) Run `sysupgrade -F /tmp/.bin`, then wait Again, this may BRICK YOUR DEVICE, so make *sure* to have your serial cable handy. Signed-off-by: Martin Kennedy [add LED migration and extend compat message] Signed-off-by: Adrian Schmutzler --- diff --git a/target/linux/ath79/dts/ar7242_meraki_mr12.dts b/target/linux/ath79/dts/ar7242_meraki_mr12.dts new file mode 100644 index 0000000000..125919d4f1 --- /dev/null +++ b/target/linux/ath79/dts/ar7242_meraki_mr12.dts @@ -0,0 +1,170 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "ar7242.dtsi" + +#include +#include + +/ { + compatible = "meraki,mr12", "qca,ar7242"; + model = "Meraki MR12"; + + aliases { + led-boot = &led_power_orange; + led-failsafe = &led_power_orange; + led-running = &led_power_green; + led-upgrade = &led_power_orange; + }; + + extosc: ref { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-output-names = "ref"; + clock-frequency = <40000000>; + }; + + leds { + compatible = "gpio-leds"; + + link1 { + label = "green:link1"; + gpios = <&gpio 11 GPIO_ACTIVE_LOW>; + }; + + link2 { + label = "green:link2"; + gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + }; + + link3 { + label = "green:link3"; + gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + }; + + link4 { + label = "green:link4"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + }; + + lan { + label = "green:lan"; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + }; + + led_power_orange: power_orange { + label = "orange:power"; + gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + panic-indicator; + }; + + led_power_green: power_green { + label = "green:power"; + gpios = <&gpio 17 GPIO_ACTIVE_LOW>; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + linux,code = ; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&pcie { + status = "okay"; + + wifi@0,0,0 { + compatible = "pci168c,002a"; + reg = <0x0000 0 0 0 0>; + qca,no-eeprom; + mtd-mac-address = <&config 0x66>; + mtd-mac-address-increment = <1>; + }; +}; + +&pll { + clocks = <&extosc>; +}; + +&uart { + status = "okay"; +}; + +&mdio0 { + status = "okay"; + + phy4: ethernet-phy@4 { + reg = <4>; + }; +}; + +ð0 { + status = "okay"; + + mtd-mac-address = <&config 0x66>; + + pll-data = <0x02000000 0x00000101 0x00001313>; + + phy-mode = "rgmii-id"; + phy-handle = <&phy4>; +}; + +&mdio1 { + status = "okay"; +}; + +ð1 { + status = "okay"; + + mtd-mac-address = <&config 0x66>; +}; + +&spi { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <50000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x000000 0x40000>; + read-only; + }; + + partition@40000 { + label = "u-boot-env"; + reg = <0x40000 0x40000>; + read-only; + }; + + config: partition@80000 { + label = "config"; + reg = <0x80000 0x20000>; + read-only; + }; + + partition@a0000 { + label = "firmware"; + reg = <0xa0000 0xf40000>; + compatible = "denx,uimage"; + }; + + partition@fe0000 { + label = "art"; + reg = <0xfe0000 0x20000>; + read-only; + }; + }; + }; +}; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds index c6ade98c8f..169df8b285 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds @@ -217,6 +217,16 @@ glinet,gl-x750) hak5,lan-turtle) ucidef_set_led_netdev "wan" "WAN" "orange:system" "eth1" ;; +meraki,mr12|\ +tplink,cpe210-v2|\ +tplink,cpe210-v3) + ucidef_set_led_netdev "lan" "LAN" "green:lan" "eth0" + ucidef_set_rssimon "wlan0" "200000" "1" + ucidef_set_led_rssi "rssilow" "RSSILOW" "green:link1" "wlan0" "1" "100" + ucidef_set_led_rssi "rssimediumlow" "RSSIMEDIUMLOW" "green:link2" "wlan0" "30" "100" + ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH" "green:link3" "wlan0" "60" "100" + ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "green:link4" "wlan0" "80" "100" + ;; meraki,mr16) ucidef_set_led_netdev "wan" "WAN" "green:wan" "eth0" ;; @@ -306,15 +316,6 @@ tplink,wbs510-v2) ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH" "green:link3" "wlan0" "60" "100" ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "green:link4" "wlan0" "80" "100" ;; -tplink,cpe210-v2|\ -tplink,cpe210-v3) - ucidef_set_led_netdev "lan" "LAN" "green:lan" "eth0" - ucidef_set_rssimon "wlan0" "200000" "1" - ucidef_set_led_rssi "rssilow" "RSSILOW" "green:link1" "wlan0" "1" "100" - ucidef_set_led_rssi "rssimediumlow" "RSSIMEDIUMLOW" "green:link2" "wlan0" "30" "100" - ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH" "green:link3" "wlan0" "60" "100" - ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "green:link4" "wlan0" "80" "100" - ;; tplink,cpe510-v2|\ tplink,cpe510-v3) ucidef_set_led_netdev "lan" "LAN" "green:lan" "eth0" diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index cb6765bba5..cb675cab1a 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -265,6 +265,11 @@ ath79_setup_interfaces() ucidef_add_switch "switch0" \ "0@eth0" "5:wan" "6@eth1" "4:lan" ;; + meraki,mr12) + ucidef_set_interface_lan "eth0" + ucidef_add_switch "switch0" \ + "0@eth1" "1:lan" + ;; mercury,mw4530r-v1|\ tplink,archer-a7-v5|\ tplink,archer-c6-v2|\ diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom index 552eb406ab..2e520ac067 100644 --- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom +++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom @@ -56,6 +56,9 @@ case "$FIRMWARE" in caldata_extract "calibrate" 0x1000 0x440 ath9k_patch_mac $(mtd_get_mac_ascii u-boot-env0 RADIOADDR1) ;; + meraki,mr12) + caldata_extract "art" 0x11000 0xeb8 + ;; nec,wg800hp) caldata_extract "art" 0x1000 0x440 ath9k_patch_mac $(mtd_get_mac_text board_data 0x680) diff --git a/target/linux/ath79/generic/base-files/etc/uci-defaults/04_led_migration b/target/linux/ath79/generic/base-files/etc/uci-defaults/04_led_migration index ea5cafa66b..e9b0fade38 100644 --- a/target/linux/ath79/generic/base-files/etc/uci-defaults/04_led_migration +++ b/target/linux/ath79/generic/base-files/etc/uci-defaults/04_led_migration @@ -17,6 +17,9 @@ engenius,epg5000) glinet,gl-mifi) migrate_leds ":net=:3g4g" ;; +meraki,mr12) + migrate_leds ":wifi=:link" ":wan=:lan" + ;; openmesh,mr600-v1) migrate_leds ":wlan58=:wifi5g" ;; diff --git a/target/linux/ath79/generic/base-files/etc/uci-defaults/05_fix-compat-version b/target/linux/ath79/generic/base-files/etc/uci-defaults/05_fix-compat-version index af5fb80f26..a6b7fa3162 100644 --- a/target/linux/ath79/generic/base-files/etc/uci-defaults/05_fix-compat-version +++ b/target/linux/ath79/generic/base-files/etc/uci-defaults/05_fix-compat-version @@ -1,6 +1,7 @@ . /lib/functions.sh case "$(board_name)" in + meraki,mr12|\ meraki,mr16) uci set system.@system[0].compat_version="2.0" uci commit system diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index c43d396db5..d11cc28146 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -1309,6 +1309,23 @@ define Device/librerouter_librerouter-v1 endef TARGET_DEVICES += librerouter_librerouter-v1 +define Device/meraki_mr12 + SOC := ar7242 + DEVICE_VENDOR := Meraki + DEVICE_MODEL := MR12 + IMAGE_SIZE := 15616k + DEVICE_PACKAGES := kmod-owl-loader rssileds + SUPPORTED_DEVICES += mr12 + DEVICE_COMPAT_VERSION := 2.0 + DEVICE_COMPAT_MESSAGE := Partitions differ from ar71xx version of MR12. Image format is incompatible. \ + To use sysupgrade, you must change /lib/update/common.sh::get_image to prepend 128K zeroes to this image, \ + and change the bootcmd in u-boot to "bootm 0xbf0a0000". After that, you can use "sysupgrade -F -n". \ + Make sure you do not keep your old config, as ethernet setup is not compatible either. \ + For more details, see the OpenWrt Wiki: https://openwrt.org/toh/meraki/MR12, \ + or the commit message of the MR12 ath79 port on git.openwrt.org. +endef +TARGET_DEVICES += meraki_mr12 + define Device/meraki_mr16 SOC := ar7161 DEVICE_VENDOR := Meraki