From: Hank Moretti Date: Fri, 21 Jul 2023 03:54:52 +0000 (+0000) Subject: mediatek: filogic: add support for Xiaomi WR30U X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=54dc1cde48a4;p=openwrt%2Fstaging%2Flinusw.git mediatek: filogic: add support for Xiaomi WR30U Hardware specification: SoC: MediaTek MT7981B 2x A53 Flash: ESMT F50L1G41LB 128MB RAM: NT52B128M16JR-FL 256MB Ethernet: 4x 10/100/1000 Mbps Switch: MediaTek MT7531AE WiFi: MediaTek MT7976C Button: Reset, Mesh Power: DC 12V 1A Flash instructions: 1. Get ssh access Check this link: https://forum.openwrt.org/t/openwrt-support-for-xiaomi-ax3000ne/153769/22 2. Backup import partitions ``` dev: size erasesize name mtd1: 00100000 00020000 "BL2" mtd2: 00040000 00020000 "Nvram" mtd3: 00040000 00020000 "Bdata" mtd4: 00200000 00020000 "Factory" mtd5: 00200000 00020000 "FIP" mtd8: 02200000 00020000 "ubi" mtd9: 02200000 00020000 "ubi1" mtd12: 00040000 00020000 "KF" ``` Use these commands blow to backup your stock partitions. ``` nanddump -f /tmp/BL2.bin /dev/mtd1 nanddump -f /tmp/Nvram.bin /dev/mtd2 nanddump -f /tmp/Bdata.bin /dev/mtd3 nanddump -f /tmp/Factory.bin /dev/mtd4 nanddump -f /tmp/FIP.bin /dev/mtd5 nanddump -f /tmp/ubi.bin /dev/mtd8 nanddump -f /tmp/KF.bin /dev/mtd12 ``` Then, transfer them to your computer via scp, netcat, tftp or others and keep them in a safe place. 3. Setup Nvram Get the current stock: `cat /proc/cmdline` If you find `firmware=0` or `mtd=ubi`, use these commands: ``` nvram set boot_wait=on nvram set uart_en=1 nvram set flag_boot_rootfs=1 nvram set flag_last_success=1 nvram set flag_boot_success=1 nvram set flag_try_sys1_failed=0 nvram set flag_try_sys2_failed=0 nvram commit ``` If you find `firmware=1` or `mtd=ubi1`, use these commands: ``` nvram set boot_wait=on nvram set uart_en=1 nvram set flag_boot_rootfs=0 nvram set flag_last_success=0 nvram set flag_boot_success=1 nvram set flag_try_sys1_failed=0 nvram set flag_try_sys2_failed=0 nvram commit ``` 4. Flash stock-initramfs-factory.ubi If you find `firmware=0` or `mtd=ubi`: `ubiformat /dev/mtd9 -y -f /tmp/stock-initramfs-factory.ubi` If you find `firmware=1` or `mtd=ubi1`: `ubiformat /dev/mtd8 -y -f /tmp/stock-initramfs-factory.ubi` Then reboot your router, it should boot to the openwrt initramfs system now. 5. Setup uboot-env Now it will be setup automatically in upgrade process, you can skip this step. If your `fw_setenv` did not work, you need run this command: `echo "/dev/mtd1 0x0 0x10000 0x20000" > /etc/fw_env.config` Then setup uboot-env: ``` fw_setenv boot_wait on fw_setenv uart_en 1 fw_setenv flag_boot_rootfs 0 fw_setenv flag_last_success 1 fw_setenv flag_boot_success 1 fw_setenv flag_try_sys1_failed 8 fw_setenv flag_try_sys2_failed 8 fw_setenv mtdparts "nmbm0:1024k(bl2),256k(Nvram),256k(Bdata), 2048k(factory),2048k(fip),256k(crash),256k(crash_log), 34816k(ubi),34816k(ubi1),32768k(overlay),12288k(data),256k(KF)" ``` 6. Flash stock-squashfs-sysupgrade.bin Use shell command: `sysupgrade -n /tmp/stock-squashfs-sysupgrade.bin` Or go to luci web. If you need to change to Openwrt U-Boot layout, do next. If you do not need, please ignore it. Change to OpenWrt U-Boot: 1. Flash ubootmod-initramfs-factory.ubi Check mtd partitions: `cat /proc/mtd` ``` mtd7: 00040000 00020000 "KF" mtd8: 02200000 00020000 "ubi_kernel" mtd9: 04e00000 00020000 "ubi" ``` Run following command: `ubiformat /dev/mtd8 -y -f /tmp/ubootmod-initramfs-factory.ubi` Then reboot your router, it should boot to the openwrt initramfs system now. 2. Check mtd again ``` mtd7: 00040000 00020000 "KF" mtd8: 07000000 00020000 "ubi" ``` Make sure mtd8 is ubi. 3. Install kmod-mtd-rw Run command: `opkg update && opkg install kmod-mtd-rw` Or get it in openwrt server, or build it yourself, then install it manually Then run this command: `insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1` 4. Clean up pstore Run Command: `rm -f /sys/fs/pstore/*` 5. Format ubi and create new ubootenv volume ``` ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8 ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB ``` 6. (Optional) Add recovery boot feature. ``` ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB ubiupdatevol /dev/ubi0_2 /tmp/ubootmod-initramfs-recovery.itb ``` 7. Flash Openwrt U-Boot ``` mtd write /tmp/ubootmod-preloader.bin BL2 mtd write /tmp/ubootmod-bl31-uboot.fip FIP ``` 6. Flash ubootmod-squashfs-sysupgrade.itb Use shell command: `sysupgrade -n /tmp/ubootmod-squashfs-sysupgrade.itb` Or go to luci web. Now everything is done, Enjoy! Go Back to stock from Openwrt U-Boot: 1. Force flash ubootmod-initramfs-recovery.itb Use shell command: `sysupgrade -F -n /tmp/ubootmod-initramfs-recovery.itb` Or go to luci web. Then it should boot to the openwrt initramfs system now. 2. Format ubi and Nvram ``` ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8 mtd erase Nvram ``` 3. Install kmod-mtd-rw Run command: `opkg update && opkg install kmod-mtd-rw` Or get it in openwrt server, or build it yourself, then install it manually Then run this command: `insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1` 4. Flash stock U-Boot and ubi ``` mtd write /tmp/BL2.bin BL2 mtd write /tmp/FIP.bin FIP mtd write /tmp/ubi.bin ubi ``` Then reboot your router, waiting it finished rollback in minutes. Go Back to stock from stock layout Openwrt: Just run command: `ubiformat /dev/mtd8 -y -f /tmp/ubi.bin` Then reboot your router, waiting it finished rollback in minutes. Notes: 1. Openwrt U-Boot and ubootmod openwrt did not enable NMBM. Please make your backup safe. Signed-off-by: Hank Moretti --- diff --git a/target/linux/mediatek/dts/mt7981b-xiaomi-mi-router-wr30u-stock.dts b/target/linux/mediatek/dts/mt7981b-xiaomi-mi-router-wr30u-stock.dts new file mode 100644 index 0000000000..7faa6e84ef --- /dev/null +++ b/target/linux/mediatek/dts/mt7981b-xiaomi-mi-router-wr30u-stock.dts @@ -0,0 +1,34 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +/dts-v1/; +#include "mt7981b-xiaomi-mi-router-wr30u.dtsi" + +/ { + model = "Xiaomi Mi Router WR30U (stock layout)"; + compatible = "xiaomi,mi-router-wr30u-stock", "mediatek,mt7981"; +}; + +&spi_nand { + mediatek,nmbm; + mediatek,bmt-max-ratio = <1>; + mediatek,bmt-max-reserved-blocks = <64>; +}; + +&partitions { + // ubi_kernel is the ubi partition in stock. + partition@600000 { + label = "ubi_kernel"; + reg = <0x600000 0x2200000>; + }; + + /* ubi is the result of squashing + * consecutive stock partitions: + * - ubi1 + * - overlay + * - data + */ + partition@2800000 { + label = "ubi"; + reg = <0x2800000 0x4e00000>; + }; +}; diff --git a/target/linux/mediatek/dts/mt7981b-xiaomi-mi-router-wr30u-ubootmod.dts b/target/linux/mediatek/dts/mt7981b-xiaomi-mi-router-wr30u-ubootmod.dts new file mode 100644 index 0000000000..6d0f3feb45 --- /dev/null +++ b/target/linux/mediatek/dts/mt7981b-xiaomi-mi-router-wr30u-ubootmod.dts @@ -0,0 +1,16 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +/dts-v1/; +#include "mt7981b-xiaomi-mi-router-wr30u.dtsi" + +/ { + model = "Xiaomi Mi Router WR30U (OpenWrt U-Boot layout)"; + compatible = "xiaomi,mi-router-wr30u-ubootmod", "mediatek,mt7981"; +}; + +&partitions { + partition@600000 { + label = "ubi"; + reg = <0x600000 0x7000000>; + }; +}; diff --git a/target/linux/mediatek/dts/mt7981b-xiaomi-mi-router-wr30u.dtsi b/target/linux/mediatek/dts/mt7981b-xiaomi-mi-router-wr30u.dtsi new file mode 100644 index 0000000000..9467b18a7e --- /dev/null +++ b/target/linux/mediatek/dts/mt7981b-xiaomi-mi-router-wr30u.dtsi @@ -0,0 +1,249 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +/dts-v1/; +#include +#include + +#include "mt7981.dtsi" + +/ { + aliases { + serial0 = &uart0; + led-boot = &led_system_yellow; + led-failsafe = &led_system_yellow; + led-running = &led_system_blue; + led-upgrade = &led_system_yellow; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory { + reg = <0 0x40000000 0 0x10000000>; + }; + + gpio-keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&pio 1 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + mesh { + label = "mesh"; + gpios = <&pio 0 GPIO_ACTIVE_LOW>; + linux,code = ; + linux,input-type = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_system_blue: system_blue { + label = "blue:system"; + gpios = <&pio 9 GPIO_ACTIVE_LOW>; + }; + + led_system_yellow: system_yellow { + label = "yellow:system"; + gpios = <&pio 10 GPIO_ACTIVE_LOW>; + }; + + led_network_blue { + label = "blue:network"; + gpios = <&pio 11 GPIO_ACTIVE_LOW>; + }; + + led_network_yellow { + label = "yellow:network"; + gpios = <&pio 12 GPIO_ACTIVE_LOW>; + }; + }; +}; + +ð { + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "2500base-x"; + + nvmem-cells = <&macaddr_factory_4>; + nvmem-cell-names = "mac-address"; + mac-address-increment = <(-1)>; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; +}; + +&mdio_bus { + switch: switch@0 { + compatible = "mediatek,mt7531"; + reg = <31>; + reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&pio>; + interrupts = <38 IRQ_TYPE_LEVEL_HIGH>; + }; +}; + +&switch { + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "wan"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@3 { + reg = <3>; + label = "lan4"; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_flash_pins>; + status = "okay"; + + spi_nand: flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spi-nand"; + reg = <0>; + + spi-max-frequency = <52000000>; + spi-tx-buswidth = <4>; + spi-rx-buswidth = <4>; + + partitions: partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "BL2"; + reg = <0x00 0x100000>; + read-only; + }; + + partition@100000 { + label = "Nvram"; + reg = <0x100000 0x40000>; + }; + + partition@140000 { + label = "Bdata"; + reg = <0x140000 0x40000>; + }; + + factory: partition@180000 { + label = "Factory"; + reg = <0x180000 0x200000>; + read-only; + + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_factory_4: macaddr@4 { + reg = <0x4 0x6>; + }; + }; + + partition@380000 { + label = "FIP"; + reg = <0x380000 0x200000>; + read-only; + }; + + partition@580000 { + label = "crash"; + reg = <0x580000 0x40000>; + read-only; + }; + + partition@5c0000 { + label = "crash_log"; + reg = <0x5c0000 0x40000>; + read-only; + }; + + partition@7600000 { + label = "KF"; + reg = <0x7600000 0x40000>; + read-only; + }; + }; + }; +}; + +&pio { + spi0_flash_pins: spi0-pins { + mux { + function = "spi"; + groups = "spi0", "spi0_wp_hold"; + }; + + conf-pu { + pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP"; + drive-strength = ; + bias-pull-up = ; + }; + + conf-pd { + pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO"; + drive-strength = ; + bias-pull-down = ; + }; + }; +}; + +&wifi { + status = "okay"; + + mediatek,mtd-eeprom = <&factory 0x0>; +}; + +&uart0 { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds index c81bd2cd97..a125c5fccb 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds @@ -20,6 +20,10 @@ netgear,wax220) ucidef_set_led_netdev "wlan2g" "WLAN2G" "blue:wlan2g" "phy0-ap0" ucidef_set_led_netdev "wlan5g" "WLAN5G" "blue:wlan5g" "phy1-ap0" ;; +xiaomi,mi-router-wr30u-stock|\ +xiaomi,mi-router-wr30u-ubootmod) + ucidef_set_led_netdev "wan" "wan" "blue:network" "wan" + ;; xiaomi,redmi-router-ax6000-stock|\ xiaomi,redmi-router-ax6000-ubootmod) ucidef_set_led_netdev "wan" "wan" "rgb:network" "wan" diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network index 3b170ddc18..589b04c74c 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network @@ -49,6 +49,8 @@ mediatek_setup_interfaces() tplink,tl-xdr6086) ucidef_set_interfaces_lan_wan "lan1 lan2" eth1 ;; + xiaomi,mi-router-wr30u-stock|\ + xiaomi,mi-router-wr30u-ubootmod|\ xiaomi,redmi-router-ax6000-stock|\ xiaomi,redmi-router-ax6000-ubootmod) ucidef_set_interfaces_lan_wan "lan2 lan3 lan4" wan @@ -94,6 +96,8 @@ mediatek_setup_macs() wan_mac=$(macaddr_add "$lan_mac" 1) label_mac=$wan_mac ;; + xiaomi,mi-router-wr30u-stock|\ + xiaomi,mi-router-wr30u-ubootmod|\ xiaomi,redmi-router-ax6000-stock|\ xiaomi,redmi-router-ax6000-ubootmod) wan_mac=$(mtd_get_mac_ascii Bdata ethaddr_wan) diff --git a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh index 186abfa5a8..b7fb2fc237 100755 --- a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh +++ b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh @@ -1,6 +1,6 @@ REQUIRE_IMAGE_METADATA=1 -redmi_ax6000_initial_setup() +xiaomi_initial_setup() { # initialize UBI and setup uboot-env if it's running on initramfs [ "$(rootfs_type)" = "tmpfs" ] || return 0 @@ -35,7 +35,15 @@ redmi_ax6000_initial_setup() fw_setenv flag_boot_success 1 fw_setenv flag_try_sys1_failed 8 fw_setenv flag_try_sys2_failed 8 - fw_setenv mtdparts "nmbm0:1024k(bl2),256k(Nvram),256k(Bdata),2048k(factory),2048k(fip),256k(crash),256k(crash_log),30720k(ubi),30720k(ubi1),51200k(overlay)" + + local board=$(board_name) + case "$board" in + xiaomi,mi-router-wr30u-stock) + fw_setenv mtdparts "nmbm0:1024k(bl2),256k(Nvram),256k(Bdata),2048k(factory),2048k(fip),256k(crash),256k(crash_log),34816k(ubi),34816k(ubi1),32768k(overlay),12288k(data),256k(KF)" + xiaomi,redmi-router-ax6000-stock) + fw_setenv mtdparts "nmbm0:1024k(bl2),256k(Nvram),256k(Bdata),2048k(factory),2048k(fip),256k(crash),256k(crash_log),30720k(ubi),30720k(ubi1),51200k(overlay)" + ;; + esac } platform_do_upgrade() { @@ -79,10 +87,12 @@ platform_do_upgrade() { tplink,tl-xdr4288|\ tplink,tl-xdr6086|\ tplink,tl-xdr6088|\ + xiaomi,mi-router-wr30u-ubootmod|\ xiaomi,redmi-router-ax6000-ubootmod) CI_KERNPART="fit" nand_do_upgrade "$1" ;; + xiaomi,mi-router-wr30u-stock|\ xiaomi,redmi-router-ax6000-stock) CI_KERN_UBIPART=ubi_kernel CI_ROOT_UBIPART=ubi @@ -135,8 +145,9 @@ platform_pre_upgrade() { local board=$(board_name) case "$board" in + xiaomi,mi-router-wr30u-stock|\ xiaomi,redmi-router-ax6000-stock) - redmi_ax6000_initial_setup + xiaomi_initial_setup ;; esac } diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk index c41cba3a64..d92ca16dc1 100644 --- a/target/linux/mediatek/image/filogic.mk +++ b/target/linux/mediatek/image/filogic.mk @@ -365,6 +365,51 @@ define Device/tplink_tl-xdr6088 endef TARGET_DEVICES += tplink_tl-xdr6088 +define Device/xiaomi_mi-router-wr30u-stock + DEVICE_VENDOR := Xiaomi + DEVICE_MODEL := Mi Router WR30U (stock layout) + DEVICE_DTS := mt7981b-xiaomi-mi-router-wr30u-stock + DEVICE_DTS_DIR := ../dts + UBINIZE_OPTS := -E 5 + BLOCKSIZE := 128k + PAGESIZE := 2048 + DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware +ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),) + ARTIFACTS := initramfs-factory.ubi + ARTIFACT/initramfs-factory.ubi := append-image-stage initramfs-kernel.bin | ubinize-kernel +endif + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata +endef +TARGET_DEVICES += xiaomi_mi-router-wr30u-stock + +define Device/xiaomi_mi-router-wr30u-ubootmod + DEVICE_VENDOR := Xiaomi + DEVICE_MODEL := Mi Router WR30U (OpenWrt U-Boot layout) + DEVICE_DTS := mt7981b-xiaomi-mi-router-wr30u-ubootmod + DEVICE_DTS_DIR := ../dts + UBINIZE_OPTS := -E 5 + BLOCKSIZE := 128k + PAGESIZE := 2048 + DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware + KERNEL_IN_UBI := 1 + UBOOTENV_IN_UBI := 1 + IMAGES := sysupgrade.itb + KERNEL_INITRAMFS_SUFFIX := -recovery.itb + KERNEL := kernel-bin | gzip + KERNEL_INITRAMFS := kernel-bin | lzma | \ + fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k + IMAGE/sysupgrade.itb := append-kernel | \ + fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | append-metadata + ARTIFACTS := preloader.bin bl31-uboot.fip + ARTIFACT/preloader.bin := mt7981-bl2 spim-nand-ddr3 + ARTIFACT/bl31-uboot.fip := mt7981-bl31-uboot xiaomi_mi-router-wr30u +ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),) + ARTIFACTS += initramfs-factory.ubi + ARTIFACT/initramfs-factory.ubi := append-image-stage initramfs-recovery.itb | ubinize-kernel +endif +endef +TARGET_DEVICES += xiaomi_mi-router-wr30u-ubootmod + define Device/xiaomi_redmi-router-ax6000-stock DEVICE_VENDOR := Xiaomi DEVICE_MODEL := Redmi Router AX6000 (stock layout)