From: Chuanhong Guo Date: Thu, 8 Aug 2024 04:56:03 +0000 (+0800) Subject: siflower: new target for Siflower SF19A2890 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=4ed209326b5299584ad22b82d0f5ba0d12ceb169;p=openwrt%2Fstaging%2Fwigyori.git siflower: new target for Siflower SF19A2890 Siflower SF19A2890 is an SoC with: Dual-core MIPS InterAptiv at 800MHz DDR3 controller One Gigabit Ethernet MAC with RGMII and IPv4 HNAT engine Built-in 2x2 11N + 2x2 11AC WiFi radio USB 2.0 OTG I2C/SPI/GPIO and various other peripherals This PR adds support for SF19A2890 EVB with ethernet support. EVB spec: Memory: DDR3 128M Ethernet: RTL8367RB 5-port gigabit switch Flash: 16M NOR Others: MicroUSB OTG, LED x 1, Reset button x1 The built image can be flashed using u-boot recovery. This target is marked as source-only until support for a commercial router board comes. Signed-off-by: Chuanhong Guo --- diff --git a/target/linux/siflower/Makefile b/target/linux/siflower/Makefile new file mode 100644 index 0000000000..d6cded021a --- /dev/null +++ b/target/linux/siflower/Makefile @@ -0,0 +1,18 @@ +# SPDX-License-Identifier: GPL-2.0-only +include $(TOPDIR)/rules.mk + +ARCH:=mipsel +BOARD:=siflower +BOARDNAME:=Siflower SoCs +FEATURES:=squashfs usb usbgadget source-only +SUBTARGETS:=sf19a2890 + +KERNEL_PATCHVER:=6.6 + +include $(INCLUDE_DIR)/target.mk + +DEFAULT_PACKAGES += \ + kmod-gpio-button-hotplug \ + uboot-envtools + +$(eval $(call BuildTarget)) diff --git a/target/linux/siflower/dts/sf19a2890.dtsi b/target/linux/siflower/dts/sf19a2890.dtsi new file mode 100644 index 0000000000..b8f1cec83e --- /dev/null +++ b/target/linux/siflower/dts/sf19a2890.dtsi @@ -0,0 +1,651 @@ +#include +#include +#include +#include + +/ { + compatible = "siflower,sf19a2890"; + #address-cells = <1>; + #size-cells = <1>; + + + aliases { + serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + }; + + chosen { + bootargs = "earlycon"; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + wlan24_dsp: wlandsp@1f00000 { + reg = <0x01f00000 0x200000>; + }; + + wlan5_dsp: wlandsp@2100000 { + reg = <0x02100000 0x200000>; + }; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + device_type = "cpu"; + compatible = "mti,interaptiv"; + reg = <0>; + clocks = <&clk CLK_MUXDIV_CPU>; + clock-names = "cpu"; + clock-latency = <0>; + }; + + cpu@1 { + device_type = "cpu"; + compatible = "mti,interaptiv"; + reg = <1>; + clocks = <&clk CLK_MUXDIV_CPU>; + clock-names = "cpu"; + clock-latency = <0>; + }; + cpu@2 { + device_type = "cpu"; + compatible = "mti,interaptiv"; + reg = <2>; + clocks = <&clk CLK_MUXDIV_CPU>; + clock-names = "cpu"; + clock-latency = <0>; + }; + cpu@3 { + device_type = "cpu"; + compatible = "mti,interaptiv"; + reg = <3>; + clocks = <&clk CLK_MUXDIV_CPU>; + clock-names = "cpu"; + clock-latency = <0>; + }; + }; + + osc32k: oscillator-32k { + compatible = "fixed-clock"; + clock-frequency = <32768>; + #clock-cells = <0>; + clock-output-names = "osc32k"; + }; + + osc12m: oscillator-12m { + compatible = "fixed-clock"; + clock-frequency = <12000000>; + #clock-cells = <0>; + clock-output-names = "osc12m"; + }; + + osc40m: oscillator-40m { + compatible = "fixed-clock"; + clock-frequency = <40000000>; + #clock-cells = <0>; + clock-output-names = "osc40m"; + }; + + soc { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + ranges; + interrupt-parent = <&gic>; + + gmac: ethernet@10800000 { + compatible = "siflower,sf19a2890-gmac", "snps,dwmac"; + reg = <0x10800000 0x200000>, + <0x19e04440 0x10>; + interrupts = , + , + ; + interrupt-names = "macirq", "eth_wake_irq", "eth_lpi"; + clocks = <&gmacclk 0>, <&gmacclk 1>, <&gmacclk 3>, <&gmacclk 2>; + clock-names = "stmmaceth", "pclk", "ptp_ref", "gmac_byp_ref"; + resets = <&gmacrst 0>; + reset-names = "stmmaceth"; + pinctrl-names = "default"; + pinctrl-0 = <&rgmii_pins>, <&mdio_pins>; + status = "disabled"; + + mdio: mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + }; + }; + + wlan_rf: phy@11c00000{ + compatible = "siflower,sf19a2890-rf"; + reg = <0x11c00000 0x600000>; + interrupts = ; + clocks = <&rfclk 1>, <&rfclk 2>, <&rfclk 3>; + clock-names = "axi", "boot", "lp"; + resets = <&rfrst 0>; + pinctrl-names = "default"; + pinctrl-0 = <&wlan_pins>; + status = "disabled"; + }; + + usb: usb@17000000 { + compatible = "siflower,sf19a2890-usb"; + reg = <0x17000000 0x40000>; + interrupts = ; + clocks = <&usbclk 0>; + clock-names = "otg"; + resets = <&usbrst 0>; + reset-names = "dwc2"; + dr_mode = "otg"; + phys = <&usb_phy>; + phy-names = "usb2-phy"; + g-np-tx-fifo-size = <768>; + status = "disabled"; + }; + + i2c: i2c@18100000 { + compatible = "snps,designware-i2c"; + reg = <0x18100000 0x1000>; + interrupts = ; + clocks = <&i2cclk 0>; + clock-names = "ref"; + resets = <&i2crst 0>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + }; + + spi: spi@18202000 { + compatible = "arm,pl022", "arm,primecell"; + reg = <0x18202000 0x1000>; + cs-gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + clocks = <&spiclk 1>, <&spiclk 0>; + clock-names = "sspclk", "apb_pclk"; + interrupts = ; + resets = <&spirst 0>; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&spi_pins>; + status = "disabled"; + }; + + uart0: serial@18300000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x18300000 0x1000>; + interrupts = ; + clocks = <&uartclk 3>, <&uartclk 0>; + clock-names = "uartclk", "apb_pclk"; + resets = <&uartrst 0>; + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins>; + status = "disabled"; + }; + + uart1: serial@18301000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x18301000 0x1000>; + interrupts = ; + clocks = <&uartclk 4>, <&uartclk 1>; + clock-names = "uartclk", "apb_pclk"; + resets = <&uartrst 1>; + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>; + status = "disabled"; + }; + + uart2: serial@18302000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x18302000 0x1000>; + interrupts = ; + clocks = <&uartclk 5>, <&uartclk 2>; + clock-names = "uartclk", "apb_pclk"; + resets = <&uartrst 2>; + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; + status = "disabled"; + }; + + watchdog: watchdog@18700000 { + compatible = "snps,dw-wdt"; + reg = <0x18700000 0x1000>; + interrupts = ; + clocks = <&wdtclk 0>; + resets = <&wdtrst 0>; + }; + + gpio: gpio@19d00000 { + compatible = "siflower,sf19a2890-gpio"; + reg=<0x19d00000 0x100000>; + interrupts = , + , + , + ; + clocks = <&gpioclk 0>; + resets = <&gpiorst 0>; + + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pinctrl 0 0 49>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + clk: clock-controller@19e01000 { + compatible = "siflower,sf19a2890-clk"; + reg = <0x19e01000 0x800>; + clocks = <&osc12m>, <&osc40m>; + clock-names = "osc12m", "osc40m"; + #clock-cells = <1>; + }; + + brom_sysm: syscon@19e02000 { + compatible = "syscon", "simple-mfd"; + reg = <0x19e02000 0x100>; + + reboot { + compatible = "syscon-reboot"; + offset = <0x30>; + value = <0x1>; + }; + }; + + gmacrst: reset-controller@19e04400 { + compatible = "siflower,sf19a2890-periph-reset"; + reg = <0x19e04400 0x4>; + #reset-cells = <1>; + siflower,reset-masks = <0x3>; + }; + + gmacclk: clock-controller@19e04404 { + compatible = "siflower,sf19a2890-periph-clk"; + reg = <0x19e04404 0xc>; + clocks = <&clk CLK_MUXDIV_BUS1>, <&clk CLK_MUXDIV_CPU>, <&clk CLK_MUXDIV_GMAC_BYP_REF>, <&clk CLK_MUXDIV_ETH_TSU>; + clock-output-names = "gmac", "gmac_pclk", "gmac_byp_ref", "ethtsu"; + #clock-cells = <1>; + }; + + wlan24rst: reset-controller@19e08000 { + compatible = "siflower,sf19a2890-periph-reset"; + reg = <0x19e08000 0x4>; + #reset-cells = <1>; + siflower,reset-masks = <0x7>; + }; + + wlan24clk: clock-controller@19e08004 { + compatible = "siflower,sf19a2890-periph-clk"; + reg = <0x19e08004 0xc>; + clocks = <&clk CLK_MUXDIV_CPU>, <&clk CLK_MUXDIV_BUS2>, <&clk CLK_MUXDIV_WLAN24_PLF>; + clock-output-names = "wlan24_axis", "wlan24_axim", "wlan24_plf"; + #clock-cells = <1>; + }; + + rfrst: reset-controller@19e08800 { + compatible = "siflower,sf19a2890-periph-reset"; + reg = <0x19e08800 0x4>; + #reset-cells = <1>; + siflower,reset-masks = <0x7>; + }; + + rfclk: clock-controller@19e08804 { + compatible = "siflower,sf19a2890-periph-clk"; + reg = <0x19e08804 0xc>; + clocks = <&clk CLK_MUXDIV_BUS2>, <&clk CLK_MUXDIV_CPU>, <&osc12m>, <&osc32k>; + clock-output-names = "rf_dft", "rf_axis", "rf_boot", "rf_lp"; + #clock-cells = <1>; + }; + + usbrst: reset-controller@19e0c000 { + compatible = "siflower,sf19a2890-periph-reset"; + reg = <0x19e0c000 0x4>; + #reset-cells = <1>; + siflower,reset-masks = <0x7 0x8 0x10>; + }; + + usbclk: clock-controller@19e0c004 { + compatible = "siflower,sf19a2890-periph-clk"; + reg = <0x19e0c004 0xc>; + clocks = <&clk CLK_MUXDIV_BUS3>, <&clk CLK_MUXDIV_CPU>, <&clk CLK_MUXDIV_USBPHY_REF>; + clock-output-names = "usb", "usb_axim", "usbphy_ref"; + siflower,valid-gates = <0xd>; + siflower,critical-gates = <0x4>; + #clock-cells = <1>; + }; + + usb_phy: usb-phy@19e0c040 { + compatible = "siflower,sf19a2890-usb-phy"; + reg = <0x19e0C040 0x60>; + clocks = <&usbclk 2>; + resets = <&usbrst 1>, <&usbrst 2>; + reset-names = "power_on_rst", "usb_phy_rst"; + #phy-cells = <0>; + status = "disabled"; + }; + + wlan5rst: reset-controller@19e0c400 { + compatible = "siflower,sf19a2890-periph-reset"; + reg = <0x19e0c400 0x4>; + #reset-cells = <1>; + siflower,reset-masks = <0x7>; + }; + + wlan5clk: clock-controller@19e0c404 { + compatible = "siflower,sf19a2890-periph-clk"; + reg = <0x19e0c404 0xc>; + clocks = <&clk CLK_MUXDIV_CPU>, <&clk CLK_MUXDIV_BUS2>, <&clk CLK_MUXDIV_WLAN5_PLF>; + clock-output-names = "wlan5_axis", "wlan5_axim", "wlan5_plf"; + #clock-cells = <1>; + }; + + i2crst: reset-controller@19e24400 { + compatible = "siflower,sf19a2890-periph-reset"; + reg = <0x19e24400 0x4>; + #reset-cells = <1>; + siflower,num-resets = <1>; + }; + + i2cclk: clock-controller@19e24404 { + compatible = "siflower,sf19a2890-periph-clk"; + reg = <0x19e24404 0xc>; + clocks = <&clk CLK_MUXDIV_PBUS>; + clock-output-names = "i2c0"; + #clock-cells = <1>; + }; + + spirst: reset-controller@19e24800 { + compatible = "siflower,sf19a2890-periph-reset"; + reg = <0x19e24800 0x4>; + #reset-cells = <1>; + siflower,reset-masks = <0x30>; + }; + + spiclk: clock-controller@19e24804 { + compatible = "siflower,sf19a2890-periph-clk"; + reg = <0x19e24804 0xc>; + clocks = <&clk CLK_MUXDIV_PBUS>, <&clk CLK_MUXDIV_PBUS>; + clock-output-names = "spi_apb", "spi_ssp"; + siflower,valid-gates = <0x30>; + #clock-cells = <1>; + }; + + uartrst: reset-controller@19e24c00 { + compatible = "siflower,sf19a2890-periph-reset"; + reg = <0x19e24c00 0x4>; + #reset-cells = <1>; + siflower,reset-masks = <0x11 0x22 0x44>; + }; + + uartclk: clock-controller@19e24c04 { + compatible = "siflower,sf19a2890-periph-clk"; + reg = <0x19e24c04 0xc>; + clocks = <&clk CLK_MUXDIV_PBUS>, <&clk CLK_MUXDIV_PBUS>, <&clk CLK_MUXDIV_PBUS>, + <&clk CLK_MUXDIV_UART>, <&clk CLK_MUXDIV_UART>, <&clk CLK_MUXDIV_UART>; + clock-output-names = "uart0_apb", "uart1_apb", "uart2_apb", + "uart0", "uart1","uart2"; + siflower,valid-gates = <0x77>; + siflower,critical-gates = <0x11>; + #clock-cells = <1>; + }; + + pwmrst: reset-controller@19e25400 { + compatible = "siflower,sf19a2890-periph-reset"; + reg = <0x19e25400 0x4>; + #reset-cells = <1>; + siflower,num-resets = <1>; + }; + + pwmclk: clock-controller@19e25404 { + compatible = "siflower,sf19a2890-periph-clk"; + reg = <0x19e25404 0xc>; + clocks = <&clk CLK_MUXDIV_PBUS>; + clock-output-names = "pwm"; + #clock-cells = <1>; + }; + + timerrst: reset-controller@19e25800 { + compatible = "siflower,sf19a2890-periph-reset"; + reg = <0x19e25800 0x4>; + #reset-cells = <1>; + siflower,num-resets = <1>; + }; + + timerclk: clock-controller@19e25804 { + compatible = "siflower,sf19a2890-periph-clk"; + reg = <0x19e25804 0xc>; + clocks = <&clk CLK_MUXDIV_PBUS>; + clock-output-names = "timer"; + #clock-cells = <1>; + }; + + wdtrst: reset-controller@19e25c00 { + compatible = "siflower,sf19a2890-periph-reset"; + reg = <0x19e25c00 0x4>; + #reset-cells = <1>; + siflower,num-resets = <1>; + }; + + wdtclk: clock-controller@19e25c04 { + compatible = "siflower,sf19a2890-periph-clk"; + reg = <0x19e25c04 0xc>; + clocks = <&clk CLK_MUXDIV_PBUS>; + clock-output-names = "wdt"; + #clock-cells = <1>; + }; + + gpiorst: reset-controller@19e2b400 { + compatible = "siflower,sf19a2890-periph-reset"; + reg = <0x19e2b400 0x4>; + #reset-cells = <1>; + siflower,num-resets = <1>; + }; + + gpioclk: clock-controller@19e2b404 { + compatible = "siflower,sf19a2890-periph-clk"; + reg = <0x19e2b404 0xc>; + clocks = <&clk CLK_MUXDIV_PBUS>; + clock-output-names = "gpio"; + #clock-cells = <1>; + }; + + pinctrl: pinctrl@19e3fc00 { + compatible = "siflower,sf19a2890-pinctrl"; + reg = <0x19e3fc00 0x400>; + + jtag_pins: jtag-pins { + tdo { + pins = "JTAG_TDO"; + function = "func0"; + bias-disable; + }; + + input-pins { + pins = "JTAG_TDI", "JTAG_TMS", "JTAG_TCK"; + function = "func0"; + input-enable; + bias-disable; + }; + + trst { + pins = "JTAG_RST"; + function = "func0"; + input-enable; + bias-pull-down; + }; + }; + + spi_pins: spi-pins { + sck { + pins = "SPI_CLK"; + function = "func0"; + bias-disable; + }; + + mosi { + pins = "SPI_TXD"; + function = "func0"; + bias-pull-down; + }; + + miso { + pins = "SPI_RXD"; + function = "func0"; + input-enable; + bias-pull-down; + }; + + cs { + pins = "SPI_CSN"; + bias-pull-up; + }; + }; + + uart0_pins: uart0-pins { + tx { + pins = "UART_TX"; + function = "func0"; + bias-pull-up; + }; + + rx { + pins = "UART_RX"; + function = "func0"; + input-enable; + bias-pull-up; + }; + }; + + uart0_rtscts: uart0-rtscts-pins { + cts { + pins = "I2C_DAT"; + function = "func0"; + input-enable; + bias-pull-up; + }; + + rts { + pins = "I2C_CLK"; + function = "func0"; + bias-pull-up; + }; + }; + + uart1_pins: uart1-pins { + tx { + pins = "JATG_TDO"; + function = "func1"; + bias-pull-up; + }; + + rx { + pins = "JATG_TDI"; + function = "func1"; + input-enable; + bias-pull-up; + }; + }; + + uart1_rtscts: uart1-rtscts-pins { + cts { + pins = "JTAG_TMS"; + function = "func1"; + input-enable; + bias-pull-up; + }; + + rts { + pins = "JTAG_TCK"; + function = "func1"; + bias-pull-up; + }; + }; + + uart2_pins: uart2-pins { + tx { + pins = "I2C_DAT"; + function = "func1"; + bias-pull-up; + }; + + rx { + pins = "I2C_CLK"; + function = "func1"; + input-enable; + bias-pull-up; + }; + }; + + rgmii_pins: rgmii-pins { + tx-pins { + pins = "RGMII_TXCLK", "RGMII_TXD0", + "RGMII_TXD1", "RGMII_TXD2", + "RGMII_TXD3", "RGMII_TXCTL"; + function = "func0"; + bias-disable; + }; + + rx-pins { + pins = "RGMII_RXCLK", "RGMII_RXD0", + "RGMII_RXD1", "RGMII_RXD2", + "RGMII_RXD3", "RGMII_RXCTL"; + function = "func0"; + input-enable; + bias-disable; + }; + }; + + mdio_pins: mdio-pins { + pins { + pins = "RGMII_MDC", "RGMII_MDIO"; + function = "func0"; + input-enable; + bias-pull-up; + }; + }; + + wlan_pins: wlan-pins { + pins { + pins = "HB0_PA_EN", "HB0_LNA_EN", + "HB0_SW_CTRL0", "HB0_SW_CTRL1", + "HB1_PA_EN", "HB1_LNA_EN", + "HB1_SW_CTRL0", "HB1_SW_CTRL1", + "LB0_PA_EN", "LB0_LNA_EN", + "LB0_SW_CTRL0", "LB0_SW_CTRL1", + "LB1_PA_EN", "LB1_LNA_EN", + "LB1_SW_CTRL0", "LB1_SW_CTRL1"; + function = "func0"; + }; + }; + + + i2c0_pins: i2c0-pins { + pins { + pins = "I2C_CLK", "I2C_DAT"; + function = "func2"; + input-enable; + bias-pull-up; + }; + }; + }; + + gic: interrupt-controller@1bdc0000 { + compatible = "mti,gic"; + reg = <0x1bdc0000 0x20000>; + interrupt-controller; + #interrupt-cells = <3>; + mti,reserved-ipi-vectors = <0 8>; + + timer { + compatible = "mti,gic-timer"; + interrupts = ; + clocks = <&clk CLK_MUXDIV_CPU>; + }; + }; + }; +}; diff --git a/target/linux/siflower/dts/sf19a2890_evb.dts b/target/linux/siflower/dts/sf19a2890_evb.dts new file mode 100644 index 0000000000..669a28b596 --- /dev/null +++ b/target/linux/siflower/dts/sf19a2890_evb.dts @@ -0,0 +1,140 @@ +/dts-v1/; +#include +#include +#include "sf19a2890.dtsi" + +/ { + model = "Siflower SF19A2890 Evaluation Board"; + compatible = "siflower,sf19a2890-evb", "siflower,sf19a2890"; + + aliases { + led-boot = &led_wlan; + led-failsafe = &led_wlan; + led-running = &led_wlan; + led-upgrade = &led_wlan; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x8000000>; + }; + + leds { + compatible = "gpio-leds"; + + led_wlan: wlan { + function = LED_FUNCTION_WLAN; + color = ; + gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&gpio 27 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + rtl8367rb { + compatible = "realtek,rtl8367b"; + realtek,extif = <6 0 0 1 1 1 1 1 1 2>; + mii-bus = <&mdio>; + phy-id = <0>; + }; +}; + +&gmac { + status = "okay"; + phy-mode = "rgmii-id"; + snps,ps-speed = <1000>; + nvmem-cells = <&macaddr_factory_0>, <&rgmii_delay_factory_b2>; + nvmem-cell-names = "mac-address", "rgmii-delay"; + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; +}; + +&wlan_rf { + status = "okay"; +}; + +&uart0 { + status = "okay"; +}; + +&usb { + status = "okay"; +}; + +&usb_phy { + status = "okay"; +}; + +&spi { + status = "okay"; + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <30000000>; + + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "spl-loader"; + reg = <0x0 0x20000>; /* 128k */ + read-only; + }; + + partition@20000 { + label = "u-boot"; + reg = <0x20000 0x60000>; /* 384k */ + }; + + partition@80000 { + label = "u-boot-env"; + reg = <0x80000 0x10000>; /* 64k */ + }; + + factory:partition@90000 { + label = "factory"; + reg = <0x90000 0x10000>; /* 64k */ + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_factory_0: macaddr@0 { + reg = <0x0 0x6>; + }; + + rgmii_delay_factory_b2: rgmii-delay@b2 { + reg = <0xb2 0x4>; + }; + }; + }; + + partition@a0000 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0xa0000 0x0>; /* 640k- */ + }; + }; + }; +}; diff --git a/target/linux/siflower/files-6.6/arch/mips/include/asm/mach-siflower/kmalloc.h b/target/linux/siflower/files-6.6/arch/mips/include/asm/mach-siflower/kmalloc.h new file mode 100644 index 0000000000..d0b270e2ec --- /dev/null +++ b/target/linux/siflower/files-6.6/arch/mips/include/asm/mach-siflower/kmalloc.h @@ -0,0 +1,9 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +#ifndef __ASM_MACH_SIFLOWER_KMALLOC_H +#define __ASM_MACH_SIFLOWER_KMALLOC_H + +#ifdef CONFIG_DMA_NONCOHERENT +#define ARCH_DMA_MINALIGN 32 +#endif + +#endif /* __ASM_MACH_SIFLOWER_KMALLOC_H */ diff --git a/target/linux/siflower/files-6.6/drivers/clk/siflower/Kconfig b/target/linux/siflower/files-6.6/drivers/clk/siflower/Kconfig new file mode 100644 index 0000000000..8e1c5a8f26 --- /dev/null +++ b/target/linux/siflower/files-6.6/drivers/clk/siflower/Kconfig @@ -0,0 +1,27 @@ +# SPDX-License-Identifier: GPL-2.0 + +menuconfig CLK_SIFLOWER + bool "Siflower SoC driver support" + depends on MIPS || COMPILE_TEST + help + SoC drivers for Siflower Linux-capable SoCs. + +if CLK_SIFLOWER + +config CLK_SF19A2890 + bool "Clock driver for Siflower CLK_SF19A2890" + depends on MIPS || COMPILE_TEST + help + Supports the Top Clock Module found in SF19A2890. If this + kernel is meant to run on a Siflower SF19A2890 SoC, + enable this driver. + +config CLK_SF19A2890_PERIPH + bool "Clock driver for Siflower SF19A2890 peripheral clock gates" + depends on MIPS || COMPILE_TEST + help + Supports the clock gates for various peripherals in SF19A2890. + If this kernel is meant to run on a Siflower SF19A2890 SoC, + enable this driver. + +endif diff --git a/target/linux/siflower/files-6.6/drivers/clk/siflower/Makefile b/target/linux/siflower/files-6.6/drivers/clk/siflower/Makefile new file mode 100644 index 0000000000..d03a72ee25 --- /dev/null +++ b/target/linux/siflower/files-6.6/drivers/clk/siflower/Makefile @@ -0,0 +1,2 @@ +obj-$(CONFIG_CLK_SF19A2890) += clk-sf19a2890.o +obj-$(CONFIG_CLK_SF19A2890_PERIPH) += clk-sf19a2890-periph.o diff --git a/target/linux/siflower/files-6.6/drivers/clk/siflower/clk-sf19a2890-periph.c b/target/linux/siflower/files-6.6/drivers/clk/siflower/clk-sf19a2890-periph.c new file mode 100644 index 0000000000..4679c714bd --- /dev/null +++ b/target/linux/siflower/files-6.6/drivers/clk/siflower/clk-sf19a2890-periph.c @@ -0,0 +1,170 @@ +// SPDX-License-Identifier: GPL-2.0 + +#include +#include +#include +#include +#include +#include + +#define REG_GATE 0x0 +/* + * A shared 'Bus Output Enable' signal for all APB peripherals. The peripheral + * only responds to bus requests if its dedicated clock is enabled and this + * shared BOE is set. + */ +#define REG_BOE 0x8 +#define BOE_EN GENMASK(1, 0) + +struct sf19a2890_periphclk { + void __iomem *base; + struct clk_hw hw; + u32 idx; +}; + +struct sf19a2890_periphclk_priv { + struct sf19a2890_periphclk *gates; + struct clk_hw_onecell_data clk_data; +}; + +static inline struct sf19a2890_periphclk *hw_to_periphclk(struct clk_hw *hw) +{ + return container_of(hw, struct sf19a2890_periphclk, hw); +} + +static int sf19a2890_periphclk_enable(struct clk_hw *hw) +{ + struct sf19a2890_periphclk *priv = hw_to_periphclk(hw); + u32 reg = readl(priv->base + REG_GATE); + + writel(reg | BIT(priv->idx), priv->base + REG_GATE); + writel(BOE_EN, priv->base + REG_BOE); + return 0; +} + +static void sf19a2890_periphclk_disable(struct clk_hw *hw) +{ + struct sf19a2890_periphclk *priv = hw_to_periphclk(hw); + u32 reg = readl(priv->base + REG_GATE); + + reg &= ~BIT(priv->idx); + writel(reg, priv->base + REG_GATE); + if (reg == 0) + writel(0, priv->base + REG_BOE); +} + +static int sf19a2890_periphclk_is_enabled(struct clk_hw *hw) +{ + struct sf19a2890_periphclk *priv = hw_to_periphclk(hw); + + return !!(readl(priv->base + REG_GATE) & BIT(priv->idx)); +} + +static const struct clk_ops sf19a28_periphclk_ops = { + .enable = sf19a2890_periphclk_enable, + .disable = sf19a2890_periphclk_disable, + .is_enabled = sf19a2890_periphclk_is_enabled, +}; + +static void __init sf19a2890_periphclk_init(struct device_node *node) +{ + struct clk_init_data init = {}; + struct sf19a2890_periphclk_priv *priv; + u32 reg, valid_gates, critical_gates; + int num_clks, i, ret, idx; + const char *name, *parent; + void __iomem *base; + + num_clks = of_count_phandle_with_args(node, "clocks", "#clock-cells"); + if (num_clks < 1 || num_clks > 32) + return; + + ret = of_property_read_u32(node, "siflower,valid-gates", &valid_gates); + if (ret < 0) + valid_gates = BIT(num_clks) - 1; + + ret = of_property_read_u32(node, "siflower,critical-gates", &critical_gates); + if (ret < 0) + critical_gates = 0; + + priv = kzalloc(struct_size(priv, clk_data.hws, num_clks), GFP_KERNEL); + if (!priv) + return; + + priv->clk_data.num = num_clks; + + priv->gates = kcalloc(num_clks, sizeof(struct sf19a2890_periphclk), + GFP_KERNEL); + if (!priv->gates) + goto err1; + + base = of_iomap(node, 0); + if (!base) { + pr_err("failed to map resources.\n"); + goto err2; + } + + /* clear unused higher bits for BOE check in disable call. */ + reg = readl(base + REG_GATE); + reg &= valid_gates; + writel(reg, base + REG_GATE); + + for (i = 0, idx = 0; i < num_clks && idx < 32; i++, idx++) { + ret = of_property_read_string_index(node, "clock-output-names", + i, &name); + if (ret != 0) { + pr_err("failed to read output name for the %dth gate.\n", + i); + goto err3; + } + parent = of_clk_get_parent_name(node, i); + if (!parent) { + pr_err("failed to get parent clock for the %dth gate.\n", + i); + goto err3; + } + + while (!(valid_gates & BIT(idx))) { + idx++; + if (idx >= 32) { + pr_err("too few valid gates."); + goto err3; + } + } + + priv->gates[i].base = base; + priv->gates[i].idx = idx; + init.name = name; + init.ops = &sf19a28_periphclk_ops; + init.parent_names = &parent; + init.num_parents = 1; + init.flags = (critical_gates & BIT(idx)) ? CLK_IS_CRITICAL : 0; + priv->gates[i].hw.init = &init; + + ret = clk_hw_register(NULL, &priv->gates[i].hw); + if (ret) { + pr_err("failed to register the %dth gate: %d.\n", i, + ret); + goto err3; + } + priv->clk_data.hws[i] = &priv->gates[i].hw; + } + + ret = of_clk_add_hw_provider(node, of_clk_hw_onecell_get, + &priv->clk_data); + if (ret) { + pr_err("failed to add hw provider.\n"); + goto err3; + } + return; +err3: + for (i--; i >= 0; i--) + clk_hw_unregister_gate(priv->clk_data.hws[i]); +err2: + kfree(priv->gates); +err1: + kfree(priv); +} + +CLK_OF_DECLARE(sf19a2890_periphclk, "siflower,sf19a2890-periph-clk", + sf19a2890_periphclk_init); diff --git a/target/linux/siflower/files-6.6/drivers/clk/siflower/clk-sf19a2890.c b/target/linux/siflower/files-6.6/drivers/clk/siflower/clk-sf19a2890.c new file mode 100644 index 0000000000..626fbe7b8e --- /dev/null +++ b/target/linux/siflower/files-6.6/drivers/clk/siflower/clk-sf19a2890.c @@ -0,0 +1,414 @@ +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define REG_PLL_BASE 0x0 +#define REG_PLL_PD 0x0 +#define PLL_PD BIT(0) +#define PLL_PD_VCO BIT(1) +#define PLL_PD_POSTDIV BIT(2) +#define PLL_PD_4PHASE BIT(3) +#define PLL_PD_DAC BIT(4) +#define PLL_PD_DSM BIT(5) + +/* + * PLL_PARAM is a 48-bit value put into 6 registers, 8-bit per register: + * REFDIV = PLL_PARAM[47:42] + * POSTDIV2 = PLL_PARAM[41:39] + * POSTDIV1 = PLL_PARAM[38:36] + * FRAC = PLL_PARAM[35:12] + * FBDIV = PLL_PARAM[11:0] + */ + +#define REG_PLL_PARAM(_x) (0x4 + (_x) * 4) +#define PLL_REFDIV_HI 47 +#define PLL_REFDIV_LO 42 +#define PLL_POSTDIV2_HI 41 +#define PLL_POSTDIV2_LO 39 +#define PLL_POSTDIV1_HI 38 +#define PLL_POSTDIV1_LO 36 +#define PLL_FRAC_HI 35 +#define PLL_FRAC_LO 12 +#define PLL_FRAC_BITS (PLL_FRAC_HI - PLL_FRAC_LO + 1) +#define PLL_FBDIV_HI 11 +#define PLL_FBDIV_LO 0 + +#define REG_PLL_CFG 0x1c +#define PLL_CFG_BYPASS BIT(0) +#define PLL_CFG_SRC GENMASK(2, 1) +#define PLL_CFG_OCLK_SEL BIT(3) +#define PLL_CFG_OCLK_GATE BIT(4) +#define PLL_CFG_LOAD_DIVS BIT(5) + +#define REG_PLL_LOCK 0x20 + +/* + * Read-only register indicating the value of the hardware clock source + * override pin. When the first bit of this register is set, PLL clock + * source is forced to the 40M oscillator regardless of PLL_CFG_SRC + * value. + */ +#define REG_PLL_SRC_OVERRIDE 0x24 + +struct sf_clk_common { + void __iomem *base; + spinlock_t *lock; + struct clk_hw hw; +}; + +struct sf19a2890_clk { + struct sf_clk_common common; + ulong offset; +}; + +#define SF_CLK_COMMON(_name, _parents, _op, _flags) \ + { \ + .hw.init = CLK_HW_INIT_PARENTS(_name, _parents, _op, _flags), \ + } + +static inline struct sf_clk_common *hw_to_sf_clk_common(struct clk_hw *hw) +{ + return container_of(hw, struct sf_clk_common, hw); +} + +static inline struct sf19a2890_clk *cmn_to_clk(struct sf_clk_common *cmn_priv) +{ + return container_of(cmn_priv, struct sf19a2890_clk, common); +} + +static inline u32 sf_readl(struct sf_clk_common *priv, u32 reg) +{ + return readl(priv->base + reg); +} + +static inline void sf_writel(struct sf_clk_common *priv, u32 reg, u32 val) +{ + return writel(val, priv->base + reg); +} + +static inline void sf_rmw(struct sf_clk_common *priv, u32 reg, u32 clr, u32 set) +{ + u32 val = sf_readl(priv, reg); + + val &= ~clr; + val |= set; + sf_writel(priv, reg, val); +} + +static u32 sf_pll_param_get(struct sf19a2890_clk *priv, u32 hi, u32 lo) +{ + struct sf_clk_common *cmn = &priv->common; + u32 ret = 0; + int reg_hi = hi / 8; + int reg_lo = lo / 8; + u32 reg_hi_pos = hi % 8; + u32 reg_lo_pos = lo % 8; + int i; + + if (reg_hi == reg_lo) { + u32 mask = (BIT(reg_hi_pos - reg_lo_pos + 1)) - 1; + u32 reg_val = + sf_readl(cmn, priv->offset + REG_PLL_PARAM(reg_hi)); + return (reg_val >> reg_lo_pos) & mask; + } + + ret = sf_readl(cmn, priv->offset + REG_PLL_PARAM(reg_hi)) & + (BIT(reg_hi_pos + 1) - 1); + for (i = reg_hi - 1; i > reg_lo; i--) + ret = (ret << 8) | + sf_readl(cmn, priv->offset + REG_PLL_PARAM(i)); + ret = (ret << (8 - reg_lo_pos)) | + (sf_readl(cmn, priv->offset + REG_PLL_PARAM(reg_lo)) >> + reg_lo_pos); + + return ret; +} + +static unsigned long sf19a28_pll_recalc_rate(struct clk_hw *hw, + unsigned long parent_rate) +{ + struct sf_clk_common *cmn_priv = hw_to_sf_clk_common(hw); + struct sf19a2890_clk *priv = cmn_to_clk(cmn_priv); + u32 refdiv = sf_pll_param_get(priv, PLL_REFDIV_HI, PLL_REFDIV_LO); + u32 fbdiv = sf_pll_param_get(priv, PLL_FBDIV_HI, PLL_FBDIV_LO); + u32 postdiv1 = sf_pll_param_get(priv, PLL_POSTDIV1_HI, PLL_POSTDIV1_LO); + u32 postdiv2 = sf_pll_param_get(priv, PLL_POSTDIV2_HI, PLL_POSTDIV2_LO); + u32 pll_pd = sf_readl(cmn_priv, PLL_PD); + u32 ref = parent_rate / refdiv; + u32 rate = ref * fbdiv; + u32 frac; + u64 frac_rate; + + if (!(pll_pd & PLL_PD_DSM)) { + frac = sf_pll_param_get(priv, PLL_FRAC_HI, PLL_FRAC_LO); + frac_rate = ((u64)rate * frac) >> PLL_FRAC_BITS; + rate += frac_rate; + } + rate = rate / postdiv1 / postdiv2; + return rate; +} + +static u8 sf19a28_pll_get_parent(struct clk_hw *hw) +{ + struct sf_clk_common *cmn_priv = hw_to_sf_clk_common(hw); + struct sf19a2890_clk *priv = cmn_to_clk(cmn_priv); + u32 cfg; + + if (sf_readl(cmn_priv, priv->offset + REG_PLL_SRC_OVERRIDE)) + return 1; + cfg = sf_readl(cmn_priv, priv->offset + REG_PLL_CFG); + return (FIELD_GET(PLL_CFG_SRC, cfg) == 1); +} + +static const struct clk_ops sf19a28_pll_ops = { + .recalc_rate = sf19a28_pll_recalc_rate, + .get_parent = sf19a28_pll_get_parent, +}; + +static const char * const clk_pll_parents[] = { "osc12m", "osc40m" }; + +#define SF19A28_PLL(_name, _offset, _flags) \ + struct sf19a2890_clk _name = { \ + .common = SF_CLK_COMMON(#_name, clk_pll_parents, \ + &sf19a28_pll_ops, _flags), \ + .offset = REG_PLL_BASE + _offset, \ + } + +static SF19A28_PLL(pll_cpu, 0x0, 0); +static SF19A28_PLL(pll_ddr, 0x40, 0); +static SF19A28_PLL(pll_cmn, 0x80, 0); + +#define REG_MUXDIV_BASE 0x400 +#define REG_MUXDIV_CFG 0x0 +#define MUXDIV_USE_NCO BIT(3) +#define MUXDIV_SRC_SEL GENMASK(2, 0) +#define REG_MUXDIV_RATIO 0x4 +#define MUXDIV_RATIO_MAX 0xff +#define REG_MUXDIV_NCO_V 0x8 +#define REG_MUXDIV_EN 0xc +#define REG_MUXDIV_XN_DIV_RATIO 0x10 +#define MUXDIV_XN_DIV_MAX 3 + +static unsigned long sf19a28_muxdiv_recalc_rate(struct clk_hw *hw, + unsigned long parent_rate) +{ + struct sf_clk_common *cmn_priv = hw_to_sf_clk_common(hw); + struct sf19a2890_clk *priv = cmn_to_clk(cmn_priv); + u32 div; + + div = sf_readl(cmn_priv, priv->offset + REG_MUXDIV_RATIO) + 1; + return parent_rate / div; +} + +int sf19a28_muxdiv_determine_rate(struct clk_hw *hw, struct clk_rate_request *req) +{ + unsigned int div; + + div = DIV_ROUND_CLOSEST(req->best_parent_rate, req->rate); + if (!div) + div = 1; + else if (div > MUXDIV_RATIO_MAX + 1) + div = MUXDIV_RATIO_MAX + 1; + + req->rate = req->best_parent_rate / div; + return 0; +} + +static int sf19a28_muxdiv_set_rate(struct clk_hw *hw, unsigned long rate, + unsigned long parent_rate) +{ + struct sf_clk_common *cmn_priv = hw_to_sf_clk_common(hw); + struct sf19a2890_clk *priv = cmn_to_clk(cmn_priv); + unsigned int div; + + div = DIV_ROUND_CLOSEST(parent_rate, rate); + if (div < 1) + div = 1; + else if (div > MUXDIV_RATIO_MAX + 1) + div = MUXDIV_RATIO_MAX + 1; + div -= 1; + + sf_writel(cmn_priv, priv->offset + REG_MUXDIV_RATIO, div); + + return 0; +} + +static int sf19a28_muxdiv_enable(struct clk_hw *hw) +{ + struct sf_clk_common *cmn_priv = hw_to_sf_clk_common(hw); + struct sf19a2890_clk *priv = cmn_to_clk(cmn_priv); + + sf_writel(cmn_priv, priv->offset + REG_MUXDIV_EN, 1); + return 0; +} + +static void sf19a28_muxdiv_disable(struct clk_hw *hw) +{ + struct sf_clk_common *cmn_priv = hw_to_sf_clk_common(hw); + struct sf19a2890_clk *priv = cmn_to_clk(cmn_priv); + + sf_writel(cmn_priv, priv->offset + REG_MUXDIV_EN, 0); +} + +static int sf19a28_muxdiv_is_enabled(struct clk_hw *hw) +{ + struct sf_clk_common *cmn_priv = hw_to_sf_clk_common(hw); + struct sf19a2890_clk *priv = cmn_to_clk(cmn_priv); + + return !!sf_readl(cmn_priv, priv->offset + REG_MUXDIV_EN); +} + +static u8 sf19a28_muxdiv_get_parent(struct clk_hw *hw) +{ + struct sf_clk_common *cmn_priv = hw_to_sf_clk_common(hw); + struct sf19a2890_clk *priv = cmn_to_clk(cmn_priv); + u32 cfg = sf_readl(cmn_priv, priv->offset + REG_MUXDIV_CFG); + u32 src = FIELD_GET(MUXDIV_SRC_SEL, cfg); + + if (src <= 2) + return src; + if (src == 4) + return 3; + return 4; +} + +static int sf19a28_muxdiv_set_parent(struct clk_hw *hw, u8 index) +{ + struct sf_clk_common *cmn_priv = hw_to_sf_clk_common(hw); + struct sf19a2890_clk *priv = cmn_to_clk(cmn_priv); + u32 src; + + if (index <= 2) + src = index; + else if (index == 3) + src = 4; + else + src = 6; + sf_writel(cmn_priv, priv->offset + REG_MUXDIV_CFG, src); + return 0; +} + +static const char * const clk_muxdiv_parents[] = { "pll_cpu", "pll_ddr", "pll_cmn", + "osc12m", "osc40m" }; + +static const struct clk_ops sf19a28_muxdiv_ops = { + .recalc_rate = sf19a28_muxdiv_recalc_rate, + .determine_rate = sf19a28_muxdiv_determine_rate, + .set_rate = sf19a28_muxdiv_set_rate, + .enable = sf19a28_muxdiv_enable, + .disable = sf19a28_muxdiv_disable, + .is_enabled = sf19a28_muxdiv_is_enabled, + .get_parent = sf19a28_muxdiv_get_parent, + .set_parent = sf19a28_muxdiv_set_parent, +}; + +#define SF19A28_MUXDIV(_name, _offset, _flags) \ + struct sf19a2890_clk _name = { \ + .common = SF_CLK_COMMON(#_name, clk_muxdiv_parents, \ + &sf19a28_muxdiv_ops, _flags), \ + .offset = REG_MUXDIV_BASE + _offset, \ + } + +static SF19A28_MUXDIV(muxdiv_bus1, 0x0, CLK_IS_CRITICAL); +static SF19A28_MUXDIV(muxdiv_bus2, 0x20, CLK_IS_CRITICAL); +static SF19A28_MUXDIV(muxdiv_bus3, 0x40, CLK_IS_CRITICAL); +static SF19A28_MUXDIV(muxdiv_cpu, 0x100, CLK_SET_RATE_PARENT | CLK_SET_RATE_NO_REPARENT); +static SF19A28_MUXDIV(muxdiv_pbus, 0x120, CLK_IS_CRITICAL); +static SF19A28_MUXDIV(muxdiv_mem_phy, 0x140, CLK_IS_CRITICAL); +static SF19A28_MUXDIV(muxdiv_uart, 0x180, 0); +static SF19A28_MUXDIV(muxdiv_eth_ref, 0x200, 0); +static SF19A28_MUXDIV(muxdiv_eth_byp_ref, 0x220, 0); +static SF19A28_MUXDIV(muxdiv_eth_tsu, 0x240, 0); +static SF19A28_MUXDIV(muxdiv_gmac_byp_ref, 0x260, 0); +static SF19A28_MUXDIV(muxdiv_m6250_0, 0x280, 0); +static SF19A28_MUXDIV(muxdiv_m6250_1, 0x2a0, 0); +static SF19A28_MUXDIV(muxdiv_wlan24_plf, 0x2c0, 0); +static SF19A28_MUXDIV(muxdiv_wlan5_plf, 0x2e0, 0); +static SF19A28_MUXDIV(muxdiv_usbphy_ref, 0x300, 0); +static SF19A28_MUXDIV(muxdiv_tclk, 0x320, 0); +static SF19A28_MUXDIV(muxdiv_npu_pe, 0x340, 0); + +static struct clk_hw_onecell_data sf19a2890_hw_clks = { + .num = CLK_SF19A2890_MAX, + .hws = { + [CLK_PLL_CPU] = &pll_cpu.common.hw, + [CLK_PLL_DDR] = &pll_ddr.common.hw, + [CLK_PLL_CMN] = &pll_cmn.common.hw, + [CLK_MUXDIV_BUS1] = &muxdiv_bus1.common.hw, + [CLK_MUXDIV_BUS2] = &muxdiv_bus2.common.hw, + [CLK_MUXDIV_BUS3] = &muxdiv_bus3.common.hw, + [CLK_MUXDIV_CPU] = &muxdiv_cpu.common.hw, + [CLK_MUXDIV_PBUS] = &muxdiv_pbus.common.hw, + [CLK_MUXDIV_MEM_PHY] = &muxdiv_mem_phy.common.hw, + [CLK_MUXDIV_UART] = &muxdiv_uart.common.hw, + [CLK_MUXDIV_ETH_REF] = &muxdiv_eth_ref.common.hw, + [CLK_MUXDIV_ETH_BYP_REF] = &muxdiv_eth_byp_ref.common.hw, + [CLK_MUXDIV_ETH_TSU] = &muxdiv_eth_tsu.common.hw, + [CLK_MUXDIV_GMAC_BYP_REF] = &muxdiv_gmac_byp_ref.common.hw, + [CLK_MUXDIV_M6250_0] = &muxdiv_m6250_0.common.hw, + [CLK_MUXDIV_M6250_1] = &muxdiv_m6250_1.common.hw, + [CLK_MUXDIV_WLAN24_PLF] = &muxdiv_wlan24_plf.common.hw, + [CLK_MUXDIV_WLAN5_PLF] = &muxdiv_wlan5_plf.common.hw, + [CLK_MUXDIV_USBPHY_REF] = &muxdiv_usbphy_ref.common.hw, + [CLK_MUXDIV_TCLK] = &muxdiv_tclk.common.hw, + [CLK_MUXDIV_NPU_PE_CLK] = &muxdiv_npu_pe.common.hw, + }, +}; + + +struct sf19a2890_clk_ctrl { + void __iomem *base; + spinlock_t lock; +}; + +static void __init sf19a2890_clk_init(struct device_node *node) +{ + struct sf19a2890_clk_ctrl *ctrl; + int i, ret; + + ctrl = kzalloc(sizeof(*ctrl), GFP_KERNEL); + if (!ctrl) + return; + + ctrl->base = of_iomap(node, 0); + if (!ctrl->base) { + pr_err("failed to map resources.\n"); + return; + } + + spin_lock_init(&ctrl->lock); + + for (i = 0; i < sf19a2890_hw_clks.num; i++) { + struct clk_hw *hw = sf19a2890_hw_clks.hws[i]; + struct sf_clk_common *common; + + if (!hw) + continue; + common = hw_to_sf_clk_common(hw); + common->base = ctrl->base; + common->lock = &ctrl->lock; + ret = clk_hw_register(NULL, hw); + if (ret) { + pr_err("Couldn't register clock %d: %d\n", i, ret); + goto err; + } + } + + ret = of_clk_add_hw_provider(node, of_clk_hw_onecell_get, &sf19a2890_hw_clks); + if (ret) { + pr_err("failed to add hw provider.\n"); + goto err; + } + return; +err: + iounmap(ctrl->base); +} + +CLK_OF_DECLARE(sf19a2890_clk, "siflower,sf19a2890-clk", sf19a2890_clk_init); diff --git a/target/linux/siflower/files-6.6/drivers/gpio/gpio-siflower.c b/target/linux/siflower/files-6.6/drivers/gpio/gpio-siflower.c new file mode 100644 index 0000000000..b28ecafec8 --- /dev/null +++ b/target/linux/siflower/files-6.6/drivers/gpio/gpio-siflower.c @@ -0,0 +1,346 @@ +// SPDX-License-Identifier: GPL-2.0+ + +#include +#include +#include +#include +#include +#include +#include + +#define GPIO_IR(n) (0x40 * (n) + 0x00) +#define GPIO_OR(n) (0x40 * (n) + 0x04) +#define GPIO_OEN(n) (0x40 * (n) + 0x08) +#define GPIO_IMR(n) (0x40 * (n) + 0x0c) +#define GPIO_GPIMR(n) (0x40 * (n) + 0x10) +#define GPIO_PIR(n) (0x40 * (n) + 0x14) +#define GPIO_ITR(n) (0x40 * (n) + 0x18) +#define GPIO_IFR(n) (0x40 * (n) + 0x1c) +#define GPIO_ICR(n) (0x40 * (n) + 0x20) +#define GPIO_GPxIR(n) (0x4 * (n) + 0x4000) + +#define GPIOS_PER_GROUP 16 + +struct sf_gpio_priv { + struct gpio_chip gc; + void __iomem *base; + struct clk *clk; + struct reset_control *rstc; + unsigned int irq[]; +}; + +#define to_sf_gpio(x) container_of(x, struct sf_gpio_priv, gc) + +static u32 sf_gpio_rd(struct sf_gpio_priv *priv, unsigned long reg) +{ + return readl_relaxed(priv->base + reg); +} + +static void sf_gpio_wr(struct sf_gpio_priv *priv, unsigned long reg, + u32 val) +{ + writel_relaxed(val, priv->base + reg); +} + +static int sf_gpio_get_value(struct gpio_chip *gc, unsigned int offset) +{ + struct sf_gpio_priv *priv = to_sf_gpio(gc); + + return sf_gpio_rd(priv, GPIO_IR(offset)); +} + +static void sf_gpio_set_value(struct gpio_chip *gc, unsigned int offset, + int value) +{ + struct sf_gpio_priv *priv = to_sf_gpio(gc); + + sf_gpio_wr(priv, GPIO_OR(offset), value); +} + +static int sf_gpio_get_direction(struct gpio_chip *gc, unsigned int offset) +{ + struct sf_gpio_priv *priv = to_sf_gpio(gc); + + if (sf_gpio_rd(priv, GPIO_OEN(offset))) + return GPIO_LINE_DIRECTION_IN; + else + return GPIO_LINE_DIRECTION_OUT; +} + +static int sf_gpio_direction_input(struct gpio_chip *gc, unsigned int offset) +{ + struct sf_gpio_priv *priv = to_sf_gpio(gc); + + sf_gpio_wr(priv, GPIO_OEN(offset), 1); + return 0; +} + +static int sf_gpio_direction_output(struct gpio_chip *gc, unsigned int offset, + int value) +{ + struct sf_gpio_priv *priv = to_sf_gpio(gc); + + sf_gpio_wr(priv, GPIO_OR(offset), value); + sf_gpio_wr(priv, GPIO_OEN(offset), 0); + return 0; +} + +static int sf_gpio_set_debounce(struct gpio_chip *gc, unsigned int offset, + u32 debounce) +{ + struct sf_gpio_priv *priv = to_sf_gpio(gc); + unsigned long freq = clk_get_rate(priv->clk); + u64 mul; + + /* (ICR + 1) * IFR = debounce_us * clkfreq_mhz / 4 */ + mul = (u64)debounce * freq; + do_div(mul, 1000000 * 4); + if (mul > 0xff00) + return -EINVAL; + + sf_gpio_wr(priv, GPIO_ICR(offset), 0xff); + sf_gpio_wr(priv, GPIO_IFR(offset), DIV_ROUND_UP(mul, 0x100)); + + return 0; +} + +static int sf_gpio_set_config(struct gpio_chip *gc, unsigned int offset, + unsigned long config) +{ + switch (pinconf_to_config_param(config)) { + case PIN_CONFIG_INPUT_DEBOUNCE: + return sf_gpio_set_debounce(gc, offset, + pinconf_to_config_argument(config)); + default: + return gpiochip_generic_config(gc, offset, config); + } +} + +static void sf_gpio_irq_ack(struct irq_data *data) +{ + struct gpio_chip *gc = irq_data_get_irq_chip_data(data); + struct sf_gpio_priv *priv = to_sf_gpio(gc); + unsigned long offset = irqd_to_hwirq(data); + + sf_gpio_wr(priv, GPIO_PIR(offset), 0); +} + +static void sf_gpio_irq_mask(struct irq_data *data) +{ + struct gpio_chip *gc = irq_data_get_irq_chip_data(data); + struct sf_gpio_priv *priv = to_sf_gpio(gc); + unsigned long offset = irqd_to_hwirq(data); + + sf_gpio_wr(priv, GPIO_IMR(offset), 1); + sf_gpio_wr(priv, GPIO_GPIMR(offset), 1); +} + +static void sf_gpio_irq_unmask(struct irq_data *data) +{ + struct gpio_chip *gc = irq_data_get_irq_chip_data(data); + struct sf_gpio_priv *priv = to_sf_gpio(gc); + unsigned long offset = irqd_to_hwirq(data); + + sf_gpio_wr(priv, GPIO_IMR(offset), 0); + sf_gpio_wr(priv, GPIO_GPIMR(offset), 0); +} + +/* We are actually setting the parents' affinity. */ +static int sf_gpio_irq_set_affinity(struct irq_data *data, + const struct cpumask *dest, bool force) +{ + struct gpio_chip *gc = irq_data_get_irq_chip_data(data); + unsigned long offset = irqd_to_hwirq(data); + const struct cpumask *pdest; + struct irq_desc *pdesc; + struct irq_data *pdata; + unsigned int group; + int ret; + + /* Find the parent IRQ and call its irq_set_affinity */ + group = offset / GPIOS_PER_GROUP; + if (group >= gc->irq.num_parents) + return -EINVAL; + + pdesc = irq_to_desc(gc->irq.parents[group]); + if (!pdesc) + return -EINVAL; + + pdata = irq_desc_get_irq_data(pdesc); + if (!pdata->chip->irq_set_affinity) + return -EINVAL; + + ret = pdata->chip->irq_set_affinity(pdata, dest, force); + if (ret < 0) + return ret; + + /* Copy its effective_affinity back */ + pdest = irq_data_get_effective_affinity_mask(pdata); + irq_data_update_effective_affinity(data, pdest); + return ret; +} + +static int sf_gpio_irq_set_type(struct irq_data *data, unsigned int flow_type) +{ + struct gpio_chip *gc = irq_data_get_irq_chip_data(data); + struct sf_gpio_priv *priv = to_sf_gpio(gc); + unsigned long offset = irqd_to_hwirq(data); + u32 val; + + switch (flow_type) { + case IRQ_TYPE_EDGE_RISING: + val = 4; + break; + case IRQ_TYPE_EDGE_FALLING: + val = 2; + break; + case IRQ_TYPE_EDGE_BOTH: + val = 6; + break; + case IRQ_TYPE_LEVEL_HIGH: + val = 1; + break; + case IRQ_TYPE_LEVEL_LOW: + val = 0; + break; + default: + return -EINVAL; + } + sf_gpio_wr(priv, GPIO_ITR(offset), val); + + if (flow_type & IRQ_TYPE_LEVEL_MASK) + irq_set_handler_locked(data, handle_level_irq); + else + irq_set_handler_locked(data, handle_edge_irq); + + return 0; +} + +static const struct irq_chip sf_gpio_irqchip = { + .name = KBUILD_MODNAME, + .irq_ack = sf_gpio_irq_ack, + .irq_mask = sf_gpio_irq_mask, + .irq_unmask = sf_gpio_irq_unmask, + .irq_set_affinity = sf_gpio_irq_set_affinity, + .irq_set_type = sf_gpio_irq_set_type, + .flags = IRQCHIP_IMMUTABLE, + GPIOCHIP_IRQ_RESOURCE_HELPERS, +}; + +static void sf_gpio_irq_handler(struct irq_desc *desc) +{ + struct gpio_chip *gc = irq_desc_get_handler_data(desc); + struct irq_chip *ic = irq_desc_get_chip(desc); + struct sf_gpio_priv *priv = to_sf_gpio(gc); + unsigned int irq = irq_desc_get_irq(desc); + unsigned int group = irq - priv->irq[0]; + unsigned long pending; + unsigned int n; + + chained_irq_enter(ic, desc); + + pending = sf_gpio_rd(priv, GPIO_GPxIR(group)); + for_each_set_bit(n, &pending, GPIOS_PER_GROUP) { + generic_handle_domain_irq(gc->irq.domain, + n + group * GPIOS_PER_GROUP); + } + + chained_irq_exit(ic, desc); +} + +static int sf_gpio_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct sf_gpio_priv *priv; + struct gpio_irq_chip *girq; + struct gpio_chip *gc; + u32 ngpios, ngroups; + int ret, i; + + ngpios = (unsigned int) device_get_match_data(dev); + ngroups = DIV_ROUND_UP(ngpios, GPIOS_PER_GROUP); + priv = devm_kzalloc(dev, struct_size(priv, irq, ngroups), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + platform_set_drvdata(pdev, priv); + + priv->base = devm_platform_ioremap_resource(pdev, 0); + if (IS_ERR(priv->base)) + return PTR_ERR(priv->base); + + priv->clk = devm_clk_get_enabled(dev, NULL); + if (IS_ERR(priv->clk)) + return PTR_ERR(priv->clk); + + priv->rstc = devm_reset_control_get_optional(&pdev->dev, NULL); + if (IS_ERR(priv->rstc)) + return PTR_ERR(priv->rstc); + + ret = reset_control_deassert(priv->rstc); + if (ret) + return ret; + + for (i = 0; i < ngroups; i++) { + ret = platform_get_irq(pdev, i); + if (ret < 0) + return ret; + + priv->irq[i] = ret; + } + + gc = &priv->gc; + gc->label = KBUILD_MODNAME; + gc->parent = dev; + gc->owner = THIS_MODULE; + gc->request = gpiochip_generic_request; + gc->free = gpiochip_generic_free; + gc->get_direction = sf_gpio_get_direction; + gc->direction_input = sf_gpio_direction_input; + gc->direction_output = sf_gpio_direction_output; + gc->get = sf_gpio_get_value; + gc->set = sf_gpio_set_value; + gc->set_config = sf_gpio_set_config; + gc->base = -1; + gc->ngpio = ngpios; + + girq = &gc->irq; + gpio_irq_chip_set_chip(girq, &sf_gpio_irqchip); + girq->num_parents = ngroups; + girq->parents = priv->irq; + girq->parent_handler = sf_gpio_irq_handler; + girq->default_type = IRQ_TYPE_NONE; + girq->handler = handle_bad_irq; + + platform_set_drvdata(pdev, priv); + return devm_gpiochip_add_data(dev, gc, priv); +} + +static int sf_gpio_remove(struct platform_device *pdev) +{ + struct sf_gpio_priv *priv = platform_get_drvdata(pdev); + + reset_control_assert(priv->rstc); + return 0; +} + +static const struct of_device_id sf_gpio_ids[] = { + { .compatible = "siflower,sf19a2890-gpio", .data = (void *)49 }, + {}, +}; +MODULE_DEVICE_TABLE(of, sf_gpio_ids); + +static struct platform_driver sf_gpio_driver = { + .probe = sf_gpio_probe, + .remove = sf_gpio_remove, + .driver = { + .name = "siflower_gpio", + .owner = THIS_MODULE, + .of_match_table = sf_gpio_ids, + }, +}; +module_platform_driver(sf_gpio_driver); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Qingfang Deng "); +MODULE_DESCRIPTION("GPIO driver for SiFlower SoCs"); diff --git a/target/linux/siflower/files-6.6/drivers/net/ethernet/stmicro/stmmac/dwmac-sf19a2890.c b/target/linux/siflower/files-6.6/drivers/net/ethernet/stmicro/stmmac/dwmac-sf19a2890.c new file mode 100644 index 0000000000..05067e9a43 --- /dev/null +++ b/target/linux/siflower/files-6.6/drivers/net/ethernet/stmicro/stmmac/dwmac-sf19a2890.c @@ -0,0 +1,193 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Siflower SF19A2890 GMAC glue layer + * SF19A2890 GMAC is a DWMAC 3.73a with a custom HNAT engine + * between its MAC and DMA engine. + * + * Copyright (C) 2024 Chuanhong Guo + */ + +#include +#include +#include +#include +#include +#include + +#include "stmmac.h" +#include "stmmac_platform.h" + +struct sf19a2890_gmac_priv { + struct device *dev; + void __iomem *gmac_cfg; + struct clk *gmac_byp_ref_clk; +}; + +#define REG_MISC 0x0 +#define MISC_PHY_INTF_SEL GENMASK(2, 0) +#define PHY_IF_GMII_MII 0 +#define PHY_IF_RGMII 1 +#define PHY_IF_RMII 4 +#define MISC_PTP_AUX_TS_TRIG BIT(3) +#define MISC_SBD_FLOWCTRL BIT(4) +#define CLK_RMII_OEN BIT(5) + +#define REG_CLK_TX_DELAY 0x4 +#define REG_CLK_RX_PHY_DELAY 0x8 +#define REG_CLK_RX_PHY_DELAY_EN 0xc + +/* Siflower stores RGMII delay as a 4-byte hex string in MTD. */ +#define SFGMAC_DELAY_STR_LEN 4 +static int sfgmac_set_delay_from_nvmem(struct sf19a2890_gmac_priv *priv) +{ + struct device_node *np = priv->dev->of_node; + int ret = 0; + struct nvmem_cell *cell; + const void *data; + size_t retlen; + u16 gmac_delay; + u8 delay_tx, delay_rx; + + cell = of_nvmem_cell_get(np, "rgmii-delay"); + if (IS_ERR(cell)) + return PTR_ERR(cell); + + data = nvmem_cell_read(cell, &retlen); + nvmem_cell_put(cell); + + if (IS_ERR(data)) + return PTR_ERR(data); + + if (retlen < SFGMAC_DELAY_STR_LEN) { + ret = -EINVAL; + goto exit; + } + + ret = kstrtou16(data, 16, &gmac_delay); + if (ret == 0) { + delay_tx = (gmac_delay >> 8) & 0xff; + delay_rx = gmac_delay & 0xff; + writel(delay_tx, priv->gmac_cfg + REG_CLK_TX_DELAY); + writel(delay_rx, priv->gmac_cfg + REG_CLK_RX_PHY_DELAY); + if (delay_rx) + writel(1, priv->gmac_cfg + REG_CLK_RX_PHY_DELAY_EN); + } + +exit: + kfree(data); + + return ret; +} + +static int sfgmac_setup_phy_interface(struct sf19a2890_gmac_priv *priv) +{ + phy_interface_t phy_iface; + int mode; + u32 reg; + + of_get_phy_mode(priv->dev->of_node, &phy_iface); + switch (phy_iface) { + case PHY_INTERFACE_MODE_MII: + case PHY_INTERFACE_MODE_GMII: + mode = PHY_IF_GMII_MII; + break; + case PHY_INTERFACE_MODE_RMII: + mode = PHY_IF_RMII; + break; + case PHY_INTERFACE_MODE_RGMII: + case PHY_INTERFACE_MODE_RGMII_ID: + case PHY_INTERFACE_MODE_RGMII_RXID: + case PHY_INTERFACE_MODE_RGMII_TXID: + mode = PHY_IF_RGMII; + break; + default: + return -EOPNOTSUPP; + } + reg = readl(priv->gmac_cfg + REG_MISC); + reg &= ~MISC_PHY_INTF_SEL; + reg |= FIELD_PREP(MISC_PHY_INTF_SEL, mode); + writel(reg, priv->gmac_cfg + REG_MISC); + return 0; +} + +static int sf19a2890_gmac_probe(struct platform_device *pdev) +{ + struct plat_stmmacenet_data *plat_dat; + struct sf19a2890_gmac_priv *priv; + struct stmmac_resources stmmac_res; + int ret; + + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + priv->dev = &pdev->dev; + + priv->gmac_byp_ref_clk = devm_clk_get_enabled(&pdev->dev, "gmac_byp_ref"); + if (IS_ERR(priv->gmac_byp_ref_clk)) + return PTR_ERR(priv->gmac_byp_ref_clk); + + priv->gmac_cfg = devm_platform_ioremap_resource(pdev, 1); + if (IS_ERR(priv->gmac_cfg)) { + dev_err(&pdev->dev, "failed to map regs for gmac config.\n"); + return PTR_ERR(priv->gmac_cfg); + } + + ret = sfgmac_set_delay_from_nvmem(priv); + if (ret == -EPROBE_DEFER) + return -EPROBE_DEFER; + + ret = sfgmac_setup_phy_interface(priv); + if (ret) + return ret; + + ret = stmmac_get_platform_resources(pdev, &stmmac_res); + if (ret) + return ret; + + plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); + if (IS_ERR(plat_dat)) { + dev_err(&pdev->dev, "dt configuration failed\n"); + return PTR_ERR(plat_dat); + } + + plat_dat->bsp_priv = priv; + /* This DWMAC has PCSSEL set, but it's not SGMII capable, and doesn't + * return anything in PCS registers under RGMII mode. + * Set this flag to bypass reading pcs regs stmmac_ethtool_get_link_ksettings. + * No idea if it's correct or not. + */ + plat_dat->flags |= STMMAC_FLAG_HAS_INTEGRATED_PCS; + + ret = stmmac_pltfr_probe(pdev, plat_dat, &stmmac_res); + if (ret) + goto err_remove_config_dt; + + return 0; + +err_remove_config_dt: + if (pdev->dev.of_node) + stmmac_remove_config_dt(pdev, plat_dat); + + return ret; +} + +static const struct of_device_id dwmac_sf19a2890_match[] = { + { .compatible = "siflower,sf19a2890-gmac"}, + { } +}; +MODULE_DEVICE_TABLE(of, dwmac_sf19a2890_match); + +static struct platform_driver sf19a2890_gmac_driver = { + .probe = sf19a2890_gmac_probe, + .remove_new = stmmac_pltfr_remove, + .driver = { + .name = "sf19a2890-gmac", + .pm = &stmmac_pltfr_pm_ops, + .of_match_table = dwmac_sf19a2890_match, + }, +}; +module_platform_driver(sf19a2890_gmac_driver); + +MODULE_DESCRIPTION("SF19A2890 GMAC driver"); +MODULE_LICENSE("GPL"); diff --git a/target/linux/siflower/files-6.6/drivers/phy/siflower/Kconfig b/target/linux/siflower/files-6.6/drivers/phy/siflower/Kconfig new file mode 100644 index 0000000000..000d1864e9 --- /dev/null +++ b/target/linux/siflower/files-6.6/drivers/phy/siflower/Kconfig @@ -0,0 +1,6 @@ +config PHY_SF19A2890_USB + tristate "SIFLOWER sf19a2890 USB2.0 PHY driver" + default n + select GENERIC_PHY + help + Enable this to support the USB2.0 PHY on the SIFLOWER SF19A2890. diff --git a/target/linux/siflower/files-6.6/drivers/phy/siflower/Makefile b/target/linux/siflower/files-6.6/drivers/phy/siflower/Makefile new file mode 100644 index 0000000000..0c65e8c866 --- /dev/null +++ b/target/linux/siflower/files-6.6/drivers/phy/siflower/Makefile @@ -0,0 +1,2 @@ +obj-$(CONFIG_PHY_SF19A2890_USB) += phy-sf19a2890-usb.o + diff --git a/target/linux/siflower/files-6.6/drivers/phy/siflower/phy-sf19a2890-usb.c b/target/linux/siflower/files-6.6/drivers/phy/siflower/phy-sf19a2890-usb.c new file mode 100644 index 0000000000..21f65957be --- /dev/null +++ b/target/linux/siflower/files-6.6/drivers/phy/siflower/phy-sf19a2890-usb.c @@ -0,0 +1,145 @@ +// SPDX-License-Identifier: GPL-2.0 + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define USB_SLEEPM 0x4 + +struct sf19a2890_usb_phy { + struct device *dev; + struct clk *phy_clk; + struct reset_control *usb_phy_rst; + struct reset_control *power_on_rst; + void __iomem *base; +}; + +static int sf19a2890_usb_phy_power_on(struct phy *phy) +{ + struct sf19a2890_usb_phy *p_phy = phy_get_drvdata(phy); + int ret; + + ret = clk_prepare_enable(p_phy->phy_clk); + if (ret < 0) { + dev_err(p_phy->dev, "Failed to enable PHY clock: %d\n", ret); + return ret; + } + + ret = reset_control_deassert(p_phy->usb_phy_rst); + if (ret) + goto err1; + + ret = reset_control_deassert(p_phy->power_on_rst); + if (ret) + goto err2; + + writel(1, p_phy->base + USB_SLEEPM); + return 0; +err2: + reset_control_assert(p_phy->usb_phy_rst); +err1: + clk_disable_unprepare(p_phy->phy_clk); + return ret; +} + +static int sf19a2890_usb_phy_power_off(struct phy *phy) +{ + struct sf19a2890_usb_phy *p_phy = phy_get_drvdata(phy); + + writel(0, p_phy->base + USB_SLEEPM); + reset_control_assert(p_phy->power_on_rst); + reset_control_assert(p_phy->usb_phy_rst); + clk_disable_unprepare(p_phy->phy_clk); + return 0; +} + +static const struct phy_ops sf19a2890_usb_phy_ops = { + .power_on = sf19a2890_usb_phy_power_on, + .power_off = sf19a2890_usb_phy_power_off, + .owner = THIS_MODULE, +}; + +static int sf19a2890_usb_phy_probe(struct platform_device *pdev) +{ + struct sf19a2890_usb_phy *p_phy; + struct phy_provider *provider; + struct phy *phy; + int ret; + + p_phy = devm_kzalloc(&pdev->dev, sizeof(*p_phy), GFP_KERNEL); + if (!p_phy) + return -ENOMEM; + + p_phy->dev = &pdev->dev; + + p_phy->base = devm_platform_ioremap_resource(pdev, 0); + if (IS_ERR(p_phy->base)) + return PTR_ERR(p_phy->base); + + p_phy->phy_clk = devm_clk_get(p_phy->dev, NULL); + if (IS_ERR(p_phy->phy_clk)) + return dev_err_probe(p_phy->dev, PTR_ERR(p_phy->phy_clk), + "failed to get usb phy clock\n"); + + p_phy->power_on_rst = + devm_reset_control_get_exclusive(&pdev->dev, "power_on_rst"); + if (IS_ERR(p_phy->power_on_rst)) + return PTR_ERR(p_phy->power_on_rst); + + ret = reset_control_assert(p_phy->power_on_rst); + if (ret) + return ret; + + p_phy->usb_phy_rst = + devm_reset_control_get_exclusive(&pdev->dev, "usb_phy_rst"); + if (IS_ERR(p_phy->usb_phy_rst)) + return PTR_ERR(p_phy->usb_phy_rst); + + ret = reset_control_assert(p_phy->usb_phy_rst); + if (ret) + return ret; + + phy = devm_phy_create(p_phy->dev, NULL, &sf19a2890_usb_phy_ops); + if (IS_ERR(phy)) + return dev_err_probe(p_phy->dev, PTR_ERR(phy), + "Failed to create PHY\n"); + + phy_set_drvdata(phy, p_phy); + + provider = + devm_of_phy_provider_register(p_phy->dev, of_phy_simple_xlate); + if (IS_ERR(provider)) + return dev_err_probe(p_phy->dev, PTR_ERR(provider), + "Failed to register PHY provider\n"); + + platform_set_drvdata(pdev, p_phy); + return 0; +} + +static const struct of_device_id sf19a2890_usb_phy_of_match[] = { + { + .compatible = "siflower,sf19a2890-usb-phy", + }, + {}, +}; +MODULE_DEVICE_TABLE(of, sf19a2890_usb_phy_of_match); + +static struct platform_driver sf19a2890_usb_phy_driver = { + .probe = sf19a2890_usb_phy_probe, + .driver = { + .name = "sf19a2890-usb-phy", + .of_match_table = sf19a2890_usb_phy_of_match, + }, +}; +module_platform_driver(sf19a2890_usb_phy_driver); + +MODULE_AUTHOR("Ziying Wu "); +MODULE_DESCRIPTION("Siflower SF19A2890 USB2.0 PHY driver"); +MODULE_LICENSE("GPL"); diff --git a/target/linux/siflower/files-6.6/drivers/pinctrl/pinctrl-sf19a2890.c b/target/linux/siflower/files-6.6/drivers/pinctrl/pinctrl-sf19a2890.c new file mode 100644 index 0000000000..42f8cb9668 --- /dev/null +++ b/target/linux/siflower/files-6.6/drivers/pinctrl/pinctrl-sf19a2890.c @@ -0,0 +1,515 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Driver for Siflower SF19A2890 pinctrl. + * + * Based on: + * Driver for Broadcom BCM2835 GPIO unit (pinctrl + GPIO) + * + * Copyright (C) 2012 Chris Boot, Simon Arlott, Stephen Warren + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define MODULE_NAME "sf19a2890-pinctrl" + +struct sf_pinctrl { + struct device *dev; + void __iomem *base; + + struct pinctrl_dev *pctl_dev; + struct pinctrl_desc pctl_desc; + struct pinctrl_gpio_range gpio_range; +}; + +#define SF19A28_NUM_GPIOS 49 + +#define SF19A28_REG_PC(pin) ((pin) * 0x8) +#define PC_OEN BIT(7) +#define PC_ST BIT(6) +#define PC_IE BIT(5) +#define PC_PD BIT(4) +#define PC_PU BIT(3) +#define PC_DS GENMASK(2, 0) + +#define DRIVE_MIN 6 +#define DRIVE_STEP 3 +#define DRIVE_MAX (7 * DRIVE_STEP) + +#define SF19A28_REG_PMX(pin) ((pin) * 0x8 + 0x4) +/* + * FUNC_SW: + * 0: Override pad output enable with PC_OEN + * 1: take OEN from GPIO or alternative function + * FMUX_SEL: + * 0: Alternative function mode + * 1: GPIO mode + */ +#define PMX_FUNC_SW BIT(3) +#define PMX_FMUX_SEL BIT(2) +#define PMX_MODE GENMASK(1, 0) + +static struct pinctrl_pin_desc sf19a2890_gpio_pins[] = { + PINCTRL_PIN(0, "JTAG_TDO"), + PINCTRL_PIN(1, "JTAG_TDI"), + PINCTRL_PIN(2, "JTAG_TMS"), + PINCTRL_PIN(3, "JTAG_TCK"), + PINCTRL_PIN(4, "JTAG_RST"), + PINCTRL_PIN(5, "SPI_TXD"), + PINCTRL_PIN(6, "SPI_RXD"), + PINCTRL_PIN(7, "SPI_CLK"), + PINCTRL_PIN(8, "SPI_CSN"), + PINCTRL_PIN(9, "UART_TX"), + PINCTRL_PIN(10, "UART_RX"), + PINCTRL_PIN(11, "I2C_DAT"), + PINCTRL_PIN(12, "I2C_CLK"), + PINCTRL_PIN(13, "RGMII_GTX_CLK"), + PINCTRL_PIN(14, "RGMII_TXCLK"), + PINCTRL_PIN(15, "RGMII_TXD0"), + PINCTRL_PIN(16, "RGMII_TXD1"), + PINCTRL_PIN(17, "RGMII_TXD2"), + PINCTRL_PIN(18, "RGMII_TXD3"), + PINCTRL_PIN(19, "RGMII_TXCTL"), + PINCTRL_PIN(20, "RGMII_RXCLK"), + PINCTRL_PIN(21, "RGMII_RXD0"), + PINCTRL_PIN(22, "RGMII_RXD1"), + PINCTRL_PIN(23, "RGMII_RXD2"), + PINCTRL_PIN(24, "RGMII_RXD3"), + PINCTRL_PIN(25, "RGMII_RXCTL"), + PINCTRL_PIN(26, "RGMII_COL"), + PINCTRL_PIN(27, "RGMII_CRS"), + PINCTRL_PIN(28, "RGMII_MDC"), + PINCTRL_PIN(29, "RGMII_MDIO"), + PINCTRL_PIN(30, "HB0_PA_EN"), + PINCTRL_PIN(31, "HB0_LNA_EN"), + PINCTRL_PIN(32, "HB0_SW_CTRL0"), + PINCTRL_PIN(33, "HB0_SW_CTRL1"), + PINCTRL_PIN(34, "HB1_PA_EN"), + PINCTRL_PIN(35, "HB1_LNA_EN"), + PINCTRL_PIN(36, "HB1_SW_CTRL0"), + PINCTRL_PIN(37, "HB1_SW_CTRL1"), + PINCTRL_PIN(38, "LB0_PA_EN"), + PINCTRL_PIN(39, "LB0_LNA_EN"), + PINCTRL_PIN(40, "LB0_SW_CTRL0"), + PINCTRL_PIN(41, "LB0_SW_CTRL1"), + PINCTRL_PIN(42, "LB1_PA_EN"), + PINCTRL_PIN(43, "LB1_LNA_EN"), + PINCTRL_PIN(44, "LB1_SW_CTRL0"), + PINCTRL_PIN(45, "LB1_SW_CTRL1"), + PINCTRL_PIN(46, "CLK_OUT"), + PINCTRL_PIN(47, "EXT_CLK_IN"), + PINCTRL_PIN(48, "DRVVBUS0"), +}; + +static const char * const sf19a2890_gpio_groups[] = { + "JTAG_TDO", + "JTAG_TDI", + "JTAG_TMS", + "JTAG_TCK", + "JTAG_RST", + "SPI_TXD", + "SPI_RXD", + "SPI_CLK", + "SPI_CSN", + "UART_TX", + "UART_RX", + "I2C_DAT", + "I2C_CLK", + "RGMII_GTX_CLK", + "RGMII_TXCLK", + "RGMII_TXD0", + "RGMII_TXD1", + "RGMII_TXD2", + "RGMII_TXD3", + "RGMII_TXCTL", + "RGMII_RXCLK", + "RGMII_RXD0", + "RGMII_RXD1", + "RGMII_RXD2", + "RGMII_RXD3", + "RGMII_RXCTL", + "RGMII_COL", + "RGMII_CRS", + "RGMII_MDC", + "RGMII_MDIO", + "HB0_PA_EN", + "HB0_LNA_EN", + "HB0_SW_CTRL0", + "HB0_SW_CTRL1", + "HB1_PA_EN", + "HB1_LNA_EN", + "HB1_SW_CTRL0", + "HB1_SW_CTRL1", + "LB0_PA_EN", + "LB0_LNA_EN", + "LB0_SW_CTRL0", + "LB0_SW_CTRL1", + "LB1_PA_EN", + "LB1_LNA_EN", + "LB1_SW_CTRL0", + "LB1_SW_CTRL1", + "CLK_OUT", + "EXT_CLK_IN", + "DRVVBUS0", +}; + +#define SF19A28_FUNC0 0 +#define SF19A28_FUNC1 1 +#define SF19A28_FUNC2 2 +#define SF19A28_FUNC3 3 +#define SF19A28_NUM_FUNCS 4 + +static const char * const sf19a2890_functions[] = { + "func0", "func1", "func2", "func3" +}; + +static inline u32 sf_pinctrl_rd(struct sf_pinctrl *pc, ulong reg) +{ + return readl(pc->base + reg); +} + +static inline void sf_pinctrl_wr(struct sf_pinctrl *pc, ulong reg, u32 val) +{ + writel(val, pc->base + reg); +} + +static inline void sf_pinctrl_rmw(struct sf_pinctrl *pc, ulong reg, u32 clr, + u32 set) +{ + u32 val; + + val = sf_pinctrl_rd(pc, reg); + val &= ~clr; + val |= set; + sf_pinctrl_wr(pc, reg, val); +} + +static int sf19a2890_pctl_get_groups_count(struct pinctrl_dev *pctldev) +{ + return SF19A28_NUM_GPIOS; +} + +static const char *sf19a2890_pctl_get_group_name(struct pinctrl_dev *pctldev, + unsigned selector) +{ + return sf19a2890_gpio_groups[selector]; +} + +static int sf19a2890_pctl_get_group_pins(struct pinctrl_dev *pctldev, + unsigned selector, + const unsigned **pins, + unsigned *num_pins) +{ + *pins = &sf19a2890_gpio_pins[selector].number; + *num_pins = 1; + + return 0; +} + +static void sf19a2890_pctl_pin_dbg_show(struct pinctrl_dev *pctldev, + struct seq_file *s, unsigned offset) +{ + struct sf_pinctrl *pc = pinctrl_dev_get_drvdata(pctldev); + u32 conf = sf_pinctrl_rd(pc, SF19A28_REG_PC(offset)); + u32 mux = sf_pinctrl_rd(pc, SF19A28_REG_PMX(offset)); + + if (!(mux & PMX_FUNC_SW)) + seq_puts(s, "Forced OE"); + else if (mux & PMX_FMUX_SEL) + seq_puts(s, "GPIO"); + else + seq_printf(s, "Func%lu", mux & PMX_MODE); + seq_puts(s, " |"); + + if (!(conf & PC_OEN) && !(mux & PMX_FUNC_SW)) + seq_puts(s, " Output"); + if ((conf & PC_ST)) + seq_puts(s, " Schmitt_Trigger"); + if ((conf & PC_IE)) + seq_puts(s, " Input"); + if ((conf & PC_PD)) + seq_puts(s, " Pull_Down"); + if ((conf & PC_PU)) + seq_puts(s, " Pull_Up"); + + seq_printf(s, " Drive: %lu mA", + DRIVE_MIN + (conf & PC_DS) * DRIVE_STEP); +} + +static const struct pinctrl_ops sf19a2890_pctl_ops = { + .get_groups_count = sf19a2890_pctl_get_groups_count, + .get_group_name = sf19a2890_pctl_get_group_name, + .get_group_pins = sf19a2890_pctl_get_group_pins, + .pin_dbg_show = sf19a2890_pctl_pin_dbg_show, + .dt_node_to_map = pinconf_generic_dt_node_to_map_all, + .dt_free_map = pinconf_generic_dt_free_map, +}; + +static int sf19a2890_pmx_free(struct pinctrl_dev *pctldev, unsigned offset) +{ + struct sf_pinctrl *pc = pinctrl_dev_get_drvdata(pctldev); + sf_pinctrl_rmw(pc, SF19A28_REG_PC(offset), PC_IE, PC_OEN); + sf_pinctrl_rmw(pc, SF19A28_REG_PMX(offset), PMX_FUNC_SW, 0); + return 0; +} + +static int sf19a2890_pmx_get_functions_count(struct pinctrl_dev *pctldev) +{ + return SF19A28_NUM_FUNCS; +} + +static const char *sf19a2890_pmx_get_function_name(struct pinctrl_dev *pctldev, + unsigned selector) +{ + return sf19a2890_functions[selector]; +} + +static int sf19a2890_pmx_get_function_groups(struct pinctrl_dev *pctldev, + unsigned selector, + const char *const **groups, + unsigned *const num_groups) +{ + /* every pin can do every function */ + *groups = sf19a2890_gpio_groups; + *num_groups = SF19A28_NUM_GPIOS; + + return 0; +} + +static int sf19a2890_pmx_set(struct pinctrl_dev *pctldev, + unsigned func_selector, unsigned group_selector) +{ + struct sf_pinctrl *pc = pinctrl_dev_get_drvdata(pctldev); + unsigned pin = group_selector; + + sf_pinctrl_wr(pc, SF19A28_REG_PMX(pin), + PMX_FUNC_SW | FIELD_PREP(PMX_MODE, func_selector)); + return 0; +} + +static int sf19a2890_pmx_gpio_request_enable(struct pinctrl_dev *pctldev, + struct pinctrl_gpio_range *range, + unsigned offset) +{ + struct sf_pinctrl *pc = pinctrl_dev_get_drvdata(pctldev); + /* Set to GPIO mode & Let peripheral control OEN */ + sf_pinctrl_wr(pc, SF19A28_REG_PMX(offset), PMX_FUNC_SW | PMX_FMUX_SEL); + /* + * Set PC_IE regardless of whether GPIO is in input mode. + * Otherwise GPIO driver can't read back its status in output mode. + */ + sf_pinctrl_rmw(pc, SF19A28_REG_PC(offset), 0, PC_IE); + return 0; +} + +static void sf19a2890_pmx_gpio_disable_free(struct pinctrl_dev *pctldev, + struct pinctrl_gpio_range *range, + unsigned offset) +{ + sf19a2890_pmx_free(pctldev, offset); +} + +static const struct pinmux_ops sf19a2890_pmx_ops = { + .free = sf19a2890_pmx_free, + .get_functions_count = sf19a2890_pmx_get_functions_count, + .get_function_name = sf19a2890_pmx_get_function_name, + .get_function_groups = sf19a2890_pmx_get_function_groups, + .set_mux = sf19a2890_pmx_set, + .gpio_request_enable = sf19a2890_pmx_gpio_request_enable, + .gpio_disable_free = sf19a2890_pmx_gpio_disable_free, +}; + +static int sf19a2890_pinconf_get(struct pinctrl_dev *pctldev, unsigned pin, + unsigned long *config) +{ + struct sf_pinctrl *pc = pinctrl_dev_get_drvdata(pctldev); + enum pin_config_param param = pinconf_to_config_param(*config); + u32 arg = 0; + u32 val = 0; + + if (pin >= SF19A28_NUM_GPIOS) + return -EINVAL; + + val = sf_pinctrl_rd(pc, SF19A28_REG_PC(pin)); + + switch (param) { + case PIN_CONFIG_INPUT_SCHMITT: + val &= PC_ST; + if (val) + arg = 1; + break; + + case PIN_CONFIG_INPUT_ENABLE: + val &= PC_IE; + if (val) + arg = 1; + break; + + case PIN_CONFIG_BIAS_PULL_DOWN: + val &= PC_PD; + if (val) + arg = 1; + break; + + case PIN_CONFIG_BIAS_PULL_UP: + val &= PC_PU; + if (val) + arg = 1; + break; + + case PIN_CONFIG_DRIVE_STRENGTH: + arg = DRIVE_MIN + (val & PC_DS) * DRIVE_STEP; + break; + + default: + return -ENOTSUPP; + } + + *config = pinconf_to_config_packed(param, arg); + return 0; +} + +static int sf19a2890_pinconf_set(struct pinctrl_dev *pctldev, unsigned pin, + unsigned long *configs, unsigned num_configs) +{ + struct sf_pinctrl *pc = pinctrl_dev_get_drvdata(pctldev); + enum pin_config_param param; + u32 arg, val; + int i; + + val = sf_pinctrl_rd(pc, SF19A28_REG_PC(pin)); + + if (pin >= SF19A28_NUM_GPIOS) + return -EINVAL; + + for (i = 0; i < num_configs; i++) { + param = pinconf_to_config_param(configs[i]); + arg = pinconf_to_config_argument(configs[i]); + switch (param) { + case PIN_CONFIG_INPUT_SCHMITT_ENABLE: + if (arg) + val |= PC_ST; + else + val &= ~PC_ST; + break; + + case PIN_CONFIG_INPUT_ENABLE: + if (arg) + val |= PC_IE; + else + val &= ~PC_IE; + break; + + case PIN_CONFIG_BIAS_PULL_DOWN: + if (arg) { + val |= PC_PD; + val &= ~PC_PU; + } else { + val &= ~PC_PD; + } + break; + + case PIN_CONFIG_BIAS_PULL_UP: + if (arg) { + val |= PC_PU; + val &= ~PC_PD; + } else { + val &= ~PC_PU; + } + break; + + case PIN_CONFIG_DRIVE_STRENGTH: + val &= ~PC_DS; + if (arg > DRIVE_MAX) + val |= PC_DS; + else if (arg > DRIVE_MIN) + val |= FIELD_PREP(PC_DS, (arg - DRIVE_MIN) / + DRIVE_STEP); + break; + default: + break; + } + sf_pinctrl_wr(pc, SF19A28_REG_PC(pin), val); + } + return 0; +} + +static const struct pinconf_ops sf19a2890_pinconf_ops = { + .is_generic = true, + .pin_config_get = sf19a2890_pinconf_get, + .pin_config_set = sf19a2890_pinconf_set, +}; + +static const struct pinctrl_desc sf19a2890_pinctrl_desc = { + .name = MODULE_NAME, + .pins = sf19a2890_gpio_pins, + .npins = SF19A28_NUM_GPIOS, + .pctlops = &sf19a2890_pctl_ops, + .pmxops = &sf19a2890_pmx_ops, + .confops = &sf19a2890_pinconf_ops, + .owner = THIS_MODULE, +}; + +static const struct pinctrl_gpio_range sf_pinctrl_gpio_range = { + .name = MODULE_NAME, + .npins = SF19A28_NUM_GPIOS, +}; + +static const struct of_device_id sf_pinctrl_match[] = { + { .compatible = "siflower,sf19a2890-pinctrl" }, + {} +}; + +static int sf_pinctrl_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct sf_pinctrl *pc; + + pc = devm_kzalloc(dev, sizeof(*pc), GFP_KERNEL); + if (!pc) + return -ENOMEM; + + platform_set_drvdata(pdev, pc); + pc->dev = dev; + + pc->base = devm_platform_ioremap_resource(pdev, 0); + if (IS_ERR(pc->base)) + return PTR_ERR(pc->base); + + pc->pctl_desc = sf19a2890_pinctrl_desc; + pc->pctl_dev = devm_pinctrl_register(dev, &pc->pctl_desc, pc); + if (IS_ERR(pc->pctl_dev)) + return PTR_ERR(pc->pctl_dev); + + return 0; +} + +static struct platform_driver sf_pinctrl_driver = { + .probe = sf_pinctrl_probe, + .driver = { + .name = MODULE_NAME, + .of_match_table = sf_pinctrl_match, + .suppress_bind_attrs = true, + }, +}; +module_platform_driver(sf_pinctrl_driver); + +MODULE_AUTHOR("Chuanhong Guo "); +MODULE_DESCRIPTION("Siflower SF19A2890 pinctrl driver"); +MODULE_LICENSE("GPL"); diff --git a/target/linux/siflower/files-6.6/drivers/reset/reset-sf19a2890-periph.c b/target/linux/siflower/files-6.6/drivers/reset/reset-sf19a2890-periph.c new file mode 100644 index 0000000000..21874da517 --- /dev/null +++ b/target/linux/siflower/files-6.6/drivers/reset/reset-sf19a2890-periph.c @@ -0,0 +1,131 @@ +// SPDX-License-Identifier: GPL-2.0-or-later + +#include +#include +#include +#include +#include +#include +#include +#include + +struct reset_sf19a28_periph_data { + struct reset_controller_dev rcdev; + void __iomem *base; + spinlock_t lock; + u32 reset_masks[]; +}; + +static inline struct reset_sf19a28_periph_data * +to_reset_sf19a28_periph_data(struct reset_controller_dev *rcdev) +{ + return container_of(rcdev, struct reset_sf19a28_periph_data, rcdev); +} + +static int reset_sf19a28_periph_update(struct reset_controller_dev *rcdev, + unsigned long id, bool assert) +{ + struct reset_sf19a28_periph_data *data = to_reset_sf19a28_periph_data(rcdev); + unsigned long flags; + u32 reg; + + spin_lock_irqsave(&data->lock, flags); + reg = readl(data->base); + if (assert) + reg |= data->reset_masks[id]; + else + reg &= ~data->reset_masks[id]; + writel(reg, data->base); + spin_unlock_irqrestore(&data->lock, flags); + return 0; +} + +static int reset_sf19a28_periph_assert(struct reset_controller_dev *rcdev, + unsigned long id) +{ + return reset_sf19a28_periph_update(rcdev, id, true); +} + +static int reset_sf19a28_periph_deassert(struct reset_controller_dev *rcdev, + unsigned long id) +{ + return reset_sf19a28_periph_update(rcdev, id, false); +} + +static int reset_sf19a28_periph_status(struct reset_controller_dev *rcdev, + unsigned long id) +{ + struct reset_sf19a28_periph_data *data = to_reset_sf19a28_periph_data(rcdev); + u32 reg; + + reg = readl(data->base); + return !!(reg & data->reset_masks[id]); +} + +const struct reset_control_ops reset_sf19a28_periph_ops = { + .assert = reset_sf19a28_periph_assert, + .deassert = reset_sf19a28_periph_deassert, + .status = reset_sf19a28_periph_status, +}; + +static const struct of_device_id reset_sf19a28_periph_dt_ids[] = { + { .compatible = "siflower,sf19a2890-periph-reset", }, + { /* sentinel */ }, +}; + +static int reset_sf19a28_periph_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct device_node *node = dev->of_node; + struct reset_sf19a28_periph_data *data; + void __iomem *base; + int nr_resets; + int ret, i; + u32 tmp; + + nr_resets = of_property_count_u32_elems(node, "siflower,reset-masks"); + + if (nr_resets < 1) { + ret = of_property_read_u32(node, "siflower,num-resets", &tmp); + if (ret < 0 || tmp < 1) + return -EINVAL; + nr_resets = tmp; + } + + if (nr_resets >= 32) { + dev_err(dev, "too many resets."); + return -EINVAL; + } + + data = devm_kzalloc(dev, struct_size(data, reset_masks, nr_resets), GFP_KERNEL); + if (!data) + return -ENOMEM; + + ret = of_property_read_u32_array(node, "siflower,reset-masks", + data->reset_masks, nr_resets); + if (ret) + for (i = 0; i < nr_resets; i++) + data->reset_masks[i] = BIT(i); + + base = devm_platform_ioremap_resource(pdev, 0); + if (IS_ERR(base)) + return PTR_ERR(base); + + spin_lock_init(&data->lock); + data->base = base; + data->rcdev.owner = THIS_MODULE; + data->rcdev.nr_resets = nr_resets; + data->rcdev.ops = &reset_sf19a28_periph_ops; + data->rcdev.of_node = dev->of_node; + + return devm_reset_controller_register(dev, &data->rcdev); +} + +static struct platform_driver reset_sf19a28_periph_driver = { + .probe = reset_sf19a28_periph_probe, + .driver = { + .name = "reset-sf19a2890-periph", + .of_match_table = reset_sf19a28_periph_dt_ids, + }, +}; +builtin_platform_driver(reset_sf19a28_periph_driver); diff --git a/target/linux/siflower/files-6.6/include/dt-bindings/clock/siflower,sf19a2890-clk.h b/target/linux/siflower/files-6.6/include/dt-bindings/clock/siflower,sf19a2890-clk.h new file mode 100644 index 0000000000..06bf0b007e --- /dev/null +++ b/target/linux/siflower/files-6.6/include/dt-bindings/clock/siflower,sf19a2890-clk.h @@ -0,0 +1,27 @@ +/* SPDX-License-Identifier: (GPL-2.0 OR MIT) */ +#ifndef __DT_BINDINGS_CLOCK_SIFLOWER_SF19A2890_CLK_H +#define __DT_BINDINGS_CLOCK_SIFLOWER_SF19A2890_CLK_H +#define CLK_PLL_CPU 0 +#define CLK_PLL_DDR 1 +#define CLK_PLL_CMN 2 +#define CLK_MUXDIV_BUS1 3 +#define CLK_MUXDIV_BUS2 4 +#define CLK_MUXDIV_BUS3 5 +#define CLK_MUXDIV_CPU 6 +#define CLK_MUXDIV_PBUS 7 +#define CLK_MUXDIV_MEM_PHY 8 +#define CLK_MUXDIV_UART 9 +#define CLK_MUXDIV_ETH_REF 10 +#define CLK_MUXDIV_ETH_BYP_REF 11 +#define CLK_MUXDIV_ETH_TSU 12 +#define CLK_MUXDIV_GMAC_BYP_REF 13 +#define CLK_MUXDIV_M6250_0 14 +#define CLK_MUXDIV_M6250_1 15 +#define CLK_MUXDIV_WLAN24_PLF 16 +#define CLK_MUXDIV_WLAN5_PLF 17 +#define CLK_MUXDIV_USBPHY_REF 18 +#define CLK_MUXDIV_TCLK 19 +#define CLK_MUXDIV_NPU_PE_CLK 20 + +#define CLK_SF19A2890_MAX 21 +#endif /* __DT_BINDINGS_CLOCK_SIFLOWER_SF19A2890_CLK_H */ diff --git a/target/linux/siflower/image/Makefile b/target/linux/siflower/image/Makefile new file mode 100644 index 0000000000..e86927dd78 --- /dev/null +++ b/target/linux/siflower/image/Makefile @@ -0,0 +1,28 @@ + +include $(TOPDIR)/rules.mk +include $(INCLUDE_DIR)/image.mk + +KERNEL_LOADADDR := 0x80100000 + +define Device/Default + PROFILES := Default + BLOCKSIZE := 64k + FILESYSTEMS := squashfs + DEVICE_DTS_DIR := ../dts + KERNEL := kernel-bin | append-dtb | lzma | uImage lzma + KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | uImage lzma + IMAGES := sysupgrade.bin + IMAGE/sysupgrade.bin = append-kernel | pad-to $$$$(BLOCKSIZE) | \ + append-rootfs | pad-rootfs | append-metadata +endef + +define Device/siflower_sf19a2890-evb + DEVICE_VENDOR := Siflower + DEVICE_MODEL := SF19A2890 EVB + BOARD_NAME := siflower,sf19a2890-evb + DEVICE_DTS := sf19a2890_evb + DEVICE_PACKAGES := kmod-switch-rtl8367b swconfig +endef +TARGET_DEVICES += siflower_sf19a2890-evb + +$(eval $(call BuildImage)) diff --git a/target/linux/siflower/modules.mk b/target/linux/siflower/modules.mk new file mode 100644 index 0000000000..e8aaf768e4 --- /dev/null +++ b/target/linux/siflower/modules.mk @@ -0,0 +1,15 @@ +define KernelPackage/phy-sf19a2890-usb + TITLE:=Siflower SF19A2890 USB 2.0 PHY Driver + KCONFIG:=CONFIG_PHY_SF19A2890_USB + DEPENDS:=@TARGET_siflower_sf19a2890 + SUBMENU:=$(USB_MENU) + FILES:=$(LINUX_DIR)/drivers/phy/siflower/phy-sf19a2890-usb.ko + AUTOLOAD:=$(call AutoLoad,45,phy-sf19a2890-usb,1) +endef + +define KernelPackage/phy-sf19a2890-usb/description + Support for Siflower SF19A2890 USB 2.0 PHY connected to the USB + controller. +endef + +$(eval $(call KernelPackage,phy-sf19a2890-usb)) diff --git a/target/linux/siflower/patches-6.6/001-mips-add-support-for-Siflower-SF19A2890.patch b/target/linux/siflower/patches-6.6/001-mips-add-support-for-Siflower-SF19A2890.patch new file mode 100644 index 0000000000..69bd0b83d7 --- /dev/null +++ b/target/linux/siflower/patches-6.6/001-mips-add-support-for-Siflower-SF19A2890.patch @@ -0,0 +1,59 @@ +From c2ec4604afb39904c01dfe38ca8289c446b898bb Mon Sep 17 00:00:00 2001 +From: Chuanhong Guo +Date: Tue, 20 Aug 2024 08:32:17 +0800 +Subject: [PATCH 1/9] mips: add support for Siflower SF19A2890 + +Signed-off-by: Chuanhong Guo +--- + arch/mips/Kconfig | 29 +++++++++++++++++++++++++++++ + arch/mips/generic/Platform | 1 + + 2 files changed, 30 insertions(+) + +--- a/arch/mips/Kconfig ++++ b/arch/mips/Kconfig +@@ -861,6 +861,35 @@ config SIBYTE_BIGSUR + select ZONE_DMA32 if 64BIT + select SWIOTLB if ARCH_DMA_ADDR_T_64BIT && PCI + ++config MACH_SIFLOWER_MIPS ++ bool "Siflower MIPS SoCs" ++ select MIPS_GENERIC ++ select ARM_AMBA ++ select BOOT_RAW ++ select CEVT_R4K ++ select CLKSRC_MIPS_GIC ++ select COMMON_CLK ++ select CPU_MIPSR2_IRQ_EI ++ select CPU_MIPSR2_IRQ_VI ++ select CSRC_R4K ++ select DMA_NONCOHERENT ++ select IRQ_MIPS_CPU ++ select MIPS_CPU_SCACHE ++ select MIPS_GIC ++ select MIPS_L1_CACHE_SHIFT_5 ++ select NO_EXCEPT_FILL ++ select SMP_UP if SMP ++ select SYS_HAS_CPU_MIPS32_R2 ++ select SYS_SUPPORTS_32BIT_KERNEL ++ select SYS_SUPPORTS_LITTLE_ENDIAN ++ select SYS_SUPPORTS_MIPS16 ++ select SYS_SUPPORTS_MIPS_CPS ++ select SYS_SUPPORTS_MULTITHREADING ++ select USE_OF ++ help ++ Select this to build a kernel which supports SoCs from Siflower ++ with MIPS InterAptiv cores, like Siflower SF19A2890. ++ + config SNI_RM + bool "SNI RM200/300/400" + select ARC_MEMORY +--- a/arch/mips/generic/Platform ++++ b/arch/mips/generic/Platform +@@ -10,6 +10,7 @@ + + # Note: order matters, keep the asm/mach-generic include last. + cflags-$(CONFIG_MACH_INGENIC_SOC) += -I$(srctree)/arch/mips/include/asm/mach-ingenic ++cflags-$(CONFIG_MACH_SIFLOWER_MIPS) += -I$(srctree)/arch/mips/include/asm/mach-siflower + cflags-$(CONFIG_MIPS_GENERIC) += -I$(srctree)/arch/mips/include/asm/mach-generic + + load-$(CONFIG_MIPS_GENERIC) += 0xffffffff80100000 diff --git a/target/linux/siflower/patches-6.6/002-clk-add-drivers-for-sf19a2890.patch b/target/linux/siflower/patches-6.6/002-clk-add-drivers-for-sf19a2890.patch new file mode 100644 index 0000000000..620e432a49 --- /dev/null +++ b/target/linux/siflower/patches-6.6/002-clk-add-drivers-for-sf19a2890.patch @@ -0,0 +1,31 @@ +From fcb96cb774abf14375326c41cedd237d6c8f6e94 Mon Sep 17 00:00:00 2001 +From: Chuanhong Guo +Date: Tue, 20 Aug 2024 08:33:01 +0800 +Subject: [PATCH 2/9] clk: add drivers for sf19a2890 + +Signed-off-by: Chuanhong Guo +--- + drivers/clk/Kconfig | 1 + + drivers/clk/Makefile | 1 + + 2 files changed, 2 insertions(+) + +--- a/drivers/clk/Kconfig ++++ b/drivers/clk/Kconfig +@@ -489,6 +489,7 @@ source "drivers/clk/renesas/Kconfig" + source "drivers/clk/rockchip/Kconfig" + source "drivers/clk/samsung/Kconfig" + source "drivers/clk/sifive/Kconfig" ++source "drivers/clk/siflower/Kconfig" + source "drivers/clk/socfpga/Kconfig" + source "drivers/clk/sprd/Kconfig" + source "drivers/clk/starfive/Kconfig" +--- a/drivers/clk/Makefile ++++ b/drivers/clk/Makefile +@@ -116,6 +116,7 @@ obj-y += renesas/ + obj-$(CONFIG_ARCH_ROCKCHIP) += rockchip/ + obj-$(CONFIG_COMMON_CLK_SAMSUNG) += samsung/ + obj-$(CONFIG_CLK_SIFIVE) += sifive/ ++obj-$(CONFIG_CLK_SIFLOWER) += siflower/ + obj-y += socfpga/ + obj-$(CONFIG_PLAT_SPEAR) += spear/ + obj-y += sprd/ diff --git a/target/linux/siflower/patches-6.6/003-reset-add-support-for-sf19a2890.patch b/target/linux/siflower/patches-6.6/003-reset-add-support-for-sf19a2890.patch new file mode 100644 index 0000000000..52992ac5dd --- /dev/null +++ b/target/linux/siflower/patches-6.6/003-reset-add-support-for-sf19a2890.patch @@ -0,0 +1,38 @@ +From 819d2a48d45f3734c876186e651917bae69be9ba Mon Sep 17 00:00:00 2001 +From: Chuanhong Guo +Date: Tue, 20 Aug 2024 08:33:43 +0800 +Subject: [PATCH 3/9] reset: add support for sf19a2890 + +Signed-off-by: Chuanhong Guo +--- + drivers/reset/Kconfig | 8 ++++++++ + drivers/reset/Makefile | 1 + + 2 files changed, 9 insertions(+) + +--- a/drivers/reset/Kconfig ++++ b/drivers/reset/Kconfig +@@ -211,6 +211,14 @@ config RESET_SCMI + This driver uses SCMI Message Protocol to interact with the + firmware controlling all the reset signals. + ++config RESET_SF19A2890_PERIPH ++ bool "Siflower SF19A2890 Peripheral Reset Controller Driver" ++ default MACH_SIFLOWER_MIPS ++ depends on HAS_IOMEM ++ help ++ This enables reset controller driver for peripheral reset blocks ++ found on Siflower SF19A2890 SoC. ++ + config RESET_SIMPLE + bool "Simple Reset Controller Driver" if COMPILE_TEST || EXPERT + default ARCH_ASPEED || ARCH_BCMBCA || ARCH_BITMAIN || ARCH_REALTEK || ARCH_STM32 || (ARCH_INTEL_SOCFPGA && ARM64) || ARCH_SUNXI || ARC +--- a/drivers/reset/Makefile ++++ b/drivers/reset/Makefile +@@ -29,6 +29,7 @@ obj-$(CONFIG_RESET_QCOM_PDC) += reset-qc + obj-$(CONFIG_RESET_RASPBERRYPI) += reset-raspberrypi.o + obj-$(CONFIG_RESET_RZG2L_USBPHY_CTRL) += reset-rzg2l-usbphy-ctrl.o + obj-$(CONFIG_RESET_SCMI) += reset-scmi.o ++obj-$(CONFIG_RESET_SF19A2890_PERIPH) += reset-sf19a2890-periph.o + obj-$(CONFIG_RESET_SIMPLE) += reset-simple.o + obj-$(CONFIG_RESET_SOCFPGA) += reset-socfpga.o + obj-$(CONFIG_RESET_SUNPLUS) += reset-sunplus.o diff --git a/target/linux/siflower/patches-6.6/004-gpio-add-support-for-siflower-socs.patch b/target/linux/siflower/patches-6.6/004-gpio-add-support-for-siflower-socs.patch new file mode 100644 index 0000000000..c381b86e14 --- /dev/null +++ b/target/linux/siflower/patches-6.6/004-gpio-add-support-for-siflower-socs.patch @@ -0,0 +1,37 @@ +From 1d37455eacb1d0c262ae6aaecadf27964cbf97d8 Mon Sep 17 00:00:00 2001 +From: Chuanhong Guo +Date: Tue, 20 Aug 2024 08:33:57 +0800 +Subject: [PATCH 4/9] gpio: add support for siflower socs + +--- + drivers/gpio/Kconfig | 8 ++++++++ + drivers/gpio/Makefile | 1 + + 2 files changed, 9 insertions(+) + +--- a/drivers/gpio/Kconfig ++++ b/drivers/gpio/Kconfig +@@ -576,6 +576,14 @@ config GPIO_SIFIVE + help + Say yes here to support the GPIO device on SiFive SoCs. + ++config GPIO_SIFLOWER ++ tristate "SiFlower GPIO support" ++ depends on OF_GPIO ++ depends on MACH_SIFLOWER_MIPS || COMPILE_TEST ++ select GPIOLIB_IRQCHIP ++ help ++ GPIO controller driver for SiFlower SoCs. ++ + config GPIO_SIOX + tristate "SIOX GPIO support" + depends on SIOX +--- a/drivers/gpio/Makefile ++++ b/drivers/gpio/Makefile +@@ -143,6 +143,7 @@ obj-$(CONFIG_GPIO_SAMA5D2_PIOBU) += gpio + obj-$(CONFIG_GPIO_SCH311X) += gpio-sch311x.o + obj-$(CONFIG_GPIO_SCH) += gpio-sch.o + obj-$(CONFIG_GPIO_SIFIVE) += gpio-sifive.o ++obj-$(CONFIG_GPIO_SIFLOWER) += gpio-siflower.o + obj-$(CONFIG_GPIO_SIM) += gpio-sim.o + obj-$(CONFIG_GPIO_SIOX) += gpio-siox.o + obj-$(CONFIG_GPIO_SL28CPLD) += gpio-sl28cpld.o diff --git a/target/linux/siflower/patches-6.6/005-pinctrl-add-driver-for-siflower-sf19a2890.patch b/target/linux/siflower/patches-6.6/005-pinctrl-add-driver-for-siflower-sf19a2890.patch new file mode 100644 index 0000000000..e9026476d3 --- /dev/null +++ b/target/linux/siflower/patches-6.6/005-pinctrl-add-driver-for-siflower-sf19a2890.patch @@ -0,0 +1,39 @@ +From 59c6a4972b584d986f72fe8d7c55930fdf799bc8 Mon Sep 17 00:00:00 2001 +From: Chuanhong Guo +Date: Tue, 20 Aug 2024 08:34:20 +0800 +Subject: [PATCH 5/9] pinctrl: add driver for siflower sf19a2890 + +--- + drivers/pinctrl/Kconfig | 10 ++++++++++ + drivers/pinctrl/Makefile | 1 + + 2 files changed, 11 insertions(+) + +--- a/drivers/pinctrl/Kconfig ++++ b/drivers/pinctrl/Kconfig +@@ -417,6 +417,16 @@ config PINCTRL_ROCKCHIP + help + This support pinctrl and GPIO driver for Rockchip SoCs. + ++config PINCTRL_SF19A2890 ++ tristate "Siflower SF19A2890 pinctrl driver" ++ depends on OF && (MACH_SIFLOWER_MIPS || COMPILE_TEST) ++ select PINMUX ++ select PINCONF ++ select GENERIC_PINCONF ++ default MACH_SIFLOWER_MIPS ++ help ++ Say Y here to enable the Siflower SF19A2890 pinctrl driver. ++ + config PINCTRL_SINGLE + tristate "One-register-per-pin type device tree based pinctrl driver" + depends on OF +--- a/drivers/pinctrl/Makefile ++++ b/drivers/pinctrl/Makefile +@@ -43,6 +43,7 @@ obj-$(CONFIG_PINCTRL_PIC32) += pinctrl-p + obj-$(CONFIG_PINCTRL_PISTACHIO) += pinctrl-pistachio.o + obj-$(CONFIG_PINCTRL_RK805) += pinctrl-rk805.o + obj-$(CONFIG_PINCTRL_ROCKCHIP) += pinctrl-rockchip.o ++obj-$(CONFIG_PINCTRL_SF19A2890) += pinctrl-sf19a2890.o + obj-$(CONFIG_PINCTRL_SINGLE) += pinctrl-single.o + obj-$(CONFIG_PINCTRL_ST) += pinctrl-st.o + obj-$(CONFIG_PINCTRL_STMFX) += pinctrl-stmfx.o diff --git a/target/linux/siflower/patches-6.6/006-stmmac-add-support-for-sf19a2890.patch b/target/linux/siflower/patches-6.6/006-stmmac-add-support-for-sf19a2890.patch new file mode 100644 index 0000000000..b65cd3ed04 --- /dev/null +++ b/target/linux/siflower/patches-6.6/006-stmmac-add-support-for-sf19a2890.patch @@ -0,0 +1,38 @@ +From baa6c00f7a88b28f6838a9743f66c9f7f4716e25 Mon Sep 17 00:00:00 2001 +From: Chuanhong Guo +Date: Tue, 20 Aug 2024 08:34:42 +0800 +Subject: [PATCH 6/9] stmmac: add support for sf19a2890 + +--- + drivers/net/ethernet/stmicro/stmmac/Kconfig | 9 +++++++++ + drivers/net/ethernet/stmicro/stmmac/Makefile | 1 + + 2 files changed, 10 insertions(+) + +--- a/drivers/net/ethernet/stmicro/stmmac/Kconfig ++++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig +@@ -142,6 +142,15 @@ config DWMAC_ROCKCHIP + This selects the Rockchip RK3288 SoC glue layer support for + the stmmac device driver. + ++config DWMAC_SF19A2890 ++ tristate "Siflower SF19A2890 GMAC support" ++ default MACH_SIFLOWER_MIPS ++ help ++ Support for GMAC on Siflower SF19A2890 SoC. ++ ++ This selects the Siflower SF19A2890 SoC glue layer support for ++ the stmmac device driver. ++ + config DWMAC_SOCFPGA + tristate "SOCFPGA dwmac support" + default ARCH_INTEL_SOCFPGA +--- a/drivers/net/ethernet/stmicro/stmmac/Makefile ++++ b/drivers/net/ethernet/stmicro/stmmac/Makefile +@@ -21,6 +21,7 @@ obj-$(CONFIG_DWMAC_MEDIATEK) += dwmac-me + obj-$(CONFIG_DWMAC_MESON) += dwmac-meson.o dwmac-meson8b.o + obj-$(CONFIG_DWMAC_QCOM_ETHQOS) += dwmac-qcom-ethqos.o + obj-$(CONFIG_DWMAC_ROCKCHIP) += dwmac-rk.o ++obj-$(CONFIG_DWMAC_SF19A2890) += dwmac-sf19a2890.o + obj-$(CONFIG_DWMAC_SOCFPGA) += dwmac-altr-socfpga.o + obj-$(CONFIG_DWMAC_STARFIVE) += dwmac-starfive.o + obj-$(CONFIG_DWMAC_STI) += dwmac-sti.o diff --git a/target/linux/siflower/patches-6.6/007-phy-add-support-for-SF19A2890-USB-PHY.patch b/target/linux/siflower/patches-6.6/007-phy-add-support-for-SF19A2890-USB-PHY.patch new file mode 100644 index 0000000000..97b7126e02 --- /dev/null +++ b/target/linux/siflower/patches-6.6/007-phy-add-support-for-SF19A2890-USB-PHY.patch @@ -0,0 +1,31 @@ +From 68817a14ae9dff587cee8515e68c67cba89b39ab Mon Sep 17 00:00:00 2001 +From: Chuanhong Guo +Date: Mon, 9 Sep 2024 10:18:33 +0800 +Subject: [PATCH 7/9] phy: add support for SF19A2890 USB PHY + +Signed-off-by: Chuanhong Guo +--- + drivers/phy/Kconfig | 1 + + drivers/phy/Makefile | 1 + + 2 files changed, 2 insertions(+) + +--- a/drivers/phy/Kconfig ++++ b/drivers/phy/Kconfig +@@ -90,6 +90,7 @@ source "drivers/phy/ralink/Kconfig" + source "drivers/phy/renesas/Kconfig" + source "drivers/phy/rockchip/Kconfig" + source "drivers/phy/samsung/Kconfig" ++source "drivers/phy/siflower/Kconfig" + source "drivers/phy/socionext/Kconfig" + source "drivers/phy/st/Kconfig" + source "drivers/phy/starfive/Kconfig" +--- a/drivers/phy/Makefile ++++ b/drivers/phy/Makefile +@@ -29,6 +29,7 @@ obj-y += allwinner/ \ + renesas/ \ + rockchip/ \ + samsung/ \ ++ siflower/ \ + socionext/ \ + st/ \ + starfive/ \ diff --git a/target/linux/siflower/patches-6.6/008-usb-dwc2-add-support-for-Siflower-SF19A2890.patch b/target/linux/siflower/patches-6.6/008-usb-dwc2-add-support-for-Siflower-SF19A2890.patch new file mode 100644 index 0000000000..b551e4f2ca --- /dev/null +++ b/target/linux/siflower/patches-6.6/008-usb-dwc2-add-support-for-Siflower-SF19A2890.patch @@ -0,0 +1,36 @@ +From 29282086f215ae723e6d2c139d23094e699ba5bb Mon Sep 17 00:00:00 2001 +From: Chuanhong Guo +Date: Mon, 9 Sep 2024 16:46:53 +0800 +Subject: [PATCH 8/9] usb: dwc2: add support for Siflower SF19A2890 + +Signed-off-by: Chuanhong Guo +--- + drivers/usb/dwc2/params.c | 10 ++++++++++ + 1 file changed, 10 insertions(+) + +--- a/drivers/usb/dwc2/params.c ++++ b/drivers/usb/dwc2/params.c +@@ -200,6 +200,14 @@ static void dwc2_set_amcc_params(struct + p->ahbcfg = GAHBCFG_HBSTLEN_INCR16 << GAHBCFG_HBSTLEN_SHIFT; + } + ++static void dwc2_set_sf19a2890_params(struct dwc2_hsotg *hsotg) ++{ ++ struct dwc2_core_params *p = &hsotg->params; ++ ++ p->max_transfer_size = 65535; ++ p->ahbcfg = GAHBCFG_HBSTLEN_INCR4 << GAHBCFG_HBSTLEN_SHIFT; ++} ++ + static void dwc2_set_stm32f4x9_fsotg_params(struct dwc2_hsotg *hsotg) + { + struct dwc2_core_params *p = &hsotg->params; +@@ -294,6 +302,8 @@ const struct of_device_id dwc2_of_match_ + .data = dwc2_set_amlogic_a1_params }, + { .compatible = "amcc,dwc-otg", .data = dwc2_set_amcc_params }, + { .compatible = "apm,apm82181-dwc-otg", .data = dwc2_set_amcc_params }, ++ { .compatible = "siflower,sf19a2890-usb", ++ .data = dwc2_set_sf19a2890_params }, + { .compatible = "st,stm32f4x9-fsotg", + .data = dwc2_set_stm32f4x9_fsotg_params }, + { .compatible = "st,stm32f4x9-hsotg" }, diff --git a/target/linux/siflower/patches-6.6/009-usb-dwc2-handle-OTG-interrupt-regardless-of-GINTSTS.patch b/target/linux/siflower/patches-6.6/009-usb-dwc2-handle-OTG-interrupt-regardless-of-GINTSTS.patch new file mode 100644 index 0000000000..03fb16879c --- /dev/null +++ b/target/linux/siflower/patches-6.6/009-usb-dwc2-handle-OTG-interrupt-regardless-of-GINTSTS.patch @@ -0,0 +1,67 @@ +From 0b04c37a1aae523025195c29a6477cf26234d26c Mon Sep 17 00:00:00 2001 +From: Chuanhong Guo +Date: Tue, 10 Sep 2024 09:10:27 +0800 +Subject: [PATCH 9/9] usb: dwc2: handle OTG interrupt regardless of GINTSTS + +The DWC OTG 3.30a found on Siflower SF19A2890 has battery charger +support enabled. It triggers MultVallpChng interrupt (bit 20 of +GOTGINT) but doesn't set OTGInt in GINTSTS. As a result, this +interrupt is never handled, and linux disables USB interrupt +because "nobody cares". + +Handle OTG interrupt in IRQ handler regardless of whether the +OTGInt bit in GINTSTS is set or not. + +Signed-off-by: Chuanhong Guo +--- + drivers/usb/dwc2/core_intr.c | 11 ++++++++--- + 1 file changed, 8 insertions(+), 3 deletions(-) + +--- a/drivers/usb/dwc2/core_intr.c ++++ b/drivers/usb/dwc2/core_intr.c +@@ -79,7 +79,7 @@ static void dwc2_handle_mode_mismatch_in + * + * @hsotg: Programming view of DWC_otg controller + */ +-static void dwc2_handle_otg_intr(struct dwc2_hsotg *hsotg) ++static irqreturn_t dwc2_handle_otg_intr(struct dwc2_hsotg *hsotg) + { + u32 gotgint; + u32 gotgctl; +@@ -87,6 +87,10 @@ static void dwc2_handle_otg_intr(struct + + gotgint = dwc2_readl(hsotg, GOTGINT); + gotgctl = dwc2_readl(hsotg, GOTGCTL); ++ ++ if (!gotgint) ++ return IRQ_NONE; ++ + dev_dbg(hsotg->dev, "++OTG Interrupt gotgint=%0x [%s]\n", gotgint, + dwc2_op_state_str(hsotg)); + +@@ -229,6 +233,7 @@ static void dwc2_handle_otg_intr(struct + + /* Clear GOTGINT */ + dwc2_writel(hsotg, gotgint, GOTGINT); ++ return IRQ_HANDLED; + } + + /** +@@ -842,6 +847,8 @@ irqreturn_t dwc2_handle_common_intr(int + hsotg->frame_number = (dwc2_readl(hsotg, HFNUM) + & HFNUM_FRNUM_MASK) >> HFNUM_FRNUM_SHIFT; + ++ retval = dwc2_handle_otg_intr(hsotg); ++ + gintsts = dwc2_read_common_intr(hsotg); + if (gintsts & ~GINTSTS_PRTINT) + retval = IRQ_HANDLED; +@@ -855,8 +862,6 @@ irqreturn_t dwc2_handle_common_intr(int + + if (gintsts & GINTSTS_MODEMIS) + dwc2_handle_mode_mismatch_intr(hsotg); +- if (gintsts & GINTSTS_OTGINT) +- dwc2_handle_otg_intr(hsotg); + if (gintsts & GINTSTS_CONIDSTSCHNG) + dwc2_handle_conn_id_status_change_intr(hsotg); + if (gintsts & GINTSTS_DISCONNINT) diff --git a/target/linux/siflower/sf19a2890/base-files/etc/board.d/02_network b/target/linux/siflower/sf19a2890/base-files/etc/board.d/02_network new file mode 100644 index 0000000000..f3da21444b --- /dev/null +++ b/target/linux/siflower/sf19a2890/base-files/etc/board.d/02_network @@ -0,0 +1,42 @@ + +. /lib/functions.sh +. /lib/functions/uci-defaults.sh +. /lib/functions/system.sh + +siflower_setup_interfaces() +{ + local board="$1" + + case $board in + siflower,sf19a2890-evb) + ucidef_add_switch "switch0" \ + "0:wan" "1:lan" "2:lan" "3:lan" "4:lan" "6@eth0" + ;; + esac +} + +siflower_setup_macs() +{ + local board="$1" + local lan_mac="" + local wan_mac="" + local label_mac="" + + case $board in + siflower,sf19a2890-evb) + wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 0x0)" 1) + ;; + esac + + [ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac + [ -n "$wan_mac" ] && ucidef_set_interface_macaddr "wan" $wan_mac + [ -n "$label_mac" ] && ucidef_set_label_macaddr $label_mac +} + +board_config_update +board=$(board_name) +siflower_setup_interfaces $board +siflower_setup_macs $board +board_config_flush + +exit 0 diff --git a/target/linux/siflower/sf19a2890/base-files/lib/upgrade/platform.sh b/target/linux/siflower/sf19a2890/base-files/lib/upgrade/platform.sh new file mode 100644 index 0000000000..80cf1cdcf0 --- /dev/null +++ b/target/linux/siflower/sf19a2890/base-files/lib/upgrade/platform.sh @@ -0,0 +1,22 @@ +PART_NAME=firmware +REQUIRE_IMAGE_METADATA=1 + +platform_check_image() { + local board=$(board_name) + + case "$board" in + *) + return 0 + ;; + esac +} + +platform_do_upgrade() { + local board=$(board_name) + + case "$board" in + *) + default_do_upgrade "$1" + ;; + esac +} diff --git a/target/linux/siflower/sf19a2890/config-6.6 b/target/linux/siflower/sf19a2890/config-6.6 new file mode 100644 index 0000000000..bec75436e0 --- /dev/null +++ b/target/linux/siflower/sf19a2890/config-6.6 @@ -0,0 +1,266 @@ +CONFIG_ARCH_32BIT_OFF_T=y +CONFIG_ARCH_HIBERNATION_POSSIBLE=y +CONFIG_ARCH_KEEP_MEMBLOCK=y +CONFIG_ARCH_MMAP_RND_BITS_MAX=15 +CONFIG_ARCH_MMAP_RND_COMPAT_BITS_MAX=15 +CONFIG_ARCH_SUSPEND_POSSIBLE=y +CONFIG_ARM_AMBA=y +CONFIG_BLK_DEV_LOOP=y +CONFIG_BOARD_SCACHE=y +CONFIG_CC_IMPLICIT_FALLTHROUGH="-Wimplicit-fallthrough=5" +CONFIG_CC_NO_ARRAY_BOUNDS=y +CONFIG_CEVT_R4K=y +CONFIG_CLKSRC_MIPS_GIC=y +CONFIG_CLK_SF19A2890=y +CONFIG_CLK_SF19A2890_PERIPH=y +CONFIG_CLK_SIFLOWER=y +CONFIG_CLOCKSOURCE_WATCHDOG=y +CONFIG_CLOCKSOURCE_WATCHDOG_MAX_SKEW_US=100 +CONFIG_CLONE_BACKWARDS=y +CONFIG_COMMON_CLK=y +CONFIG_COMPACT_UNEVICTABLE_DEFAULT=1 +CONFIG_COMPAT_32BIT_TIME=y +CONFIG_CONNECTOR=y +CONFIG_CONSOLE_LOGLEVEL_DEFAULT=15 +CONFIG_CONTEXT_TRACKING=y +CONFIG_CONTEXT_TRACKING_IDLE=y +CONFIG_COREDUMP=y +CONFIG_CPU_GENERIC_DUMP_TLB=y +CONFIG_CPU_HAS_DIEI=y +CONFIG_CPU_HAS_PREFETCH=y +CONFIG_CPU_HAS_RIXI=y +CONFIG_CPU_HAS_SYNC=y +CONFIG_CPU_LITTLE_ENDIAN=y +CONFIG_CPU_MIPS32=y +CONFIG_CPU_MIPS32_R2=y +CONFIG_CPU_MIPSR2=y +CONFIG_CPU_MIPSR2_IRQ_EI=y +CONFIG_CPU_MIPSR2_IRQ_VI=y +CONFIG_CPU_MITIGATIONS=y +CONFIG_CPU_NEEDS_NO_SMARTMIPS_OR_MICROMIPS=y +CONFIG_CPU_R4K_CACHE_TLB=y +CONFIG_CPU_R4K_FPU=y +CONFIG_CPU_RMAP=y +CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y +CONFIG_CPU_SUPPORTS_HIGHMEM=y +CONFIG_CPU_SUPPORTS_MSA=y +CONFIG_CRC16=y +CONFIG_CRC_CCITT=y +CONFIG_CRYPTO_LIB_BLAKE2S_GENERIC=y +CONFIG_CRYPTO_LIB_GF128MUL=y +CONFIG_CRYPTO_LIB_POLY1305_RSIZE=2 +CONFIG_CRYPTO_LIB_SHA1=y +CONFIG_CRYPTO_LIB_UTILS=y +CONFIG_CSRC_R4K=y +CONFIG_DEBUG_INFO=y +CONFIG_DEBUG_INFO_REDUCED=y +CONFIG_DMA_NONCOHERENT=y +CONFIG_DTC=y +# CONFIG_DWMAC_GENERIC is not set +CONFIG_DWMAC_SF19A2890=y +CONFIG_DW_WATCHDOG=y +CONFIG_ELF_CORE=y +CONFIG_EXCLUSIVE_SYSTEM_RAM=y +CONFIG_FANOTIFY=y +CONFIG_FHANDLE=y +CONFIG_FIXED_PHY=y +CONFIG_FS_IOMAP=y +CONFIG_FUNCTION_ALIGNMENT=0 +CONFIG_FWNODE_MDIO=y +CONFIG_FW_LOADER_PAGED_BUF=y +CONFIG_FW_LOADER_SYSFS=y +CONFIG_GCC10_NO_ARRAY_BOUNDS=y +CONFIG_GENERIC_ALLOCATOR=y +CONFIG_GENERIC_ATOMIC64=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_CPU_AUTOPROBE=y +CONFIG_GENERIC_GETTIMEOFDAY=y +CONFIG_GENERIC_IDLE_POLL_SETUP=y +CONFIG_GENERIC_IOMAP=y +CONFIG_GENERIC_IRQ_CHIP=y +CONFIG_GENERIC_IRQ_EFFECTIVE_AFF_MASK=y +CONFIG_GENERIC_IRQ_MIGRATION=y +CONFIG_GENERIC_IRQ_SHOW=y +CONFIG_GENERIC_LIB_ASHLDI3=y +CONFIG_GENERIC_LIB_ASHRDI3=y +CONFIG_GENERIC_LIB_CMPDI2=y +CONFIG_GENERIC_LIB_LSHRDI3=y +CONFIG_GENERIC_LIB_UCMPDI2=y +CONFIG_GENERIC_PCI_IOMAP=y +CONFIG_GENERIC_PHY=y +CONFIG_GENERIC_PINCONF=y +CONFIG_GENERIC_SCHED_CLOCK=y +CONFIG_GENERIC_SMP_IDLE_THREAD=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GPIOLIB_IRQCHIP=y +CONFIG_GPIO_CDEV=y +CONFIG_GPIO_SIFLOWER=y +CONFIG_GRO_CELLS=y +CONFIG_HARDWARE_WATCHPOINTS=y +CONFIG_HAS_DMA=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAS_IOPORT_MAP=y +CONFIG_HOTPLUG_CORE_SYNC=y +CONFIG_HOTPLUG_CORE_SYNC_DEAD=y +CONFIG_HOTPLUG_CPU=y +CONFIG_INITRAMFS_SOURCE="" +CONFIG_IRQCHIP=y +CONFIG_IRQ_DOMAIN=y +CONFIG_IRQ_DOMAIN_HIERARCHY=y +CONFIG_IRQ_FORCED_THREADING=y +CONFIG_IRQ_MIPS_CPU=y +CONFIG_IRQ_WORK=y +CONFIG_LEDS_GPIO=y +CONFIG_LIBFDT=y +CONFIG_LOCK_DEBUGGING_SUPPORT=y +CONFIG_MACH_SIFLOWER_MIPS=y +CONFIG_MDIO_BUS=y +CONFIG_MDIO_DEVICE=y +CONFIG_MDIO_DEVRES=y +CONFIG_MFD_SYSCON=y +CONFIG_MICREL_PHY=y +CONFIG_MIGRATION=y +CONFIG_MIPS=y +CONFIG_MIPS_ASID_BITS=8 +CONFIG_MIPS_ASID_SHIFT=0 +CONFIG_MIPS_CLOCK_VSYSCALL=y +CONFIG_MIPS_CM=y +CONFIG_MIPS_CMDLINE_DTB_EXTEND=y +# CONFIG_MIPS_CMDLINE_FROM_BOOTLOADER is not set +CONFIG_MIPS_CPC=y +CONFIG_MIPS_CPS=y +# CONFIG_MIPS_CPS_NS16550_BOOL is not set +CONFIG_MIPS_CPS_PM=y +CONFIG_MIPS_CPU_SCACHE=y +CONFIG_MIPS_FP_SUPPORT=y +CONFIG_MIPS_GENERIC=y +CONFIG_MIPS_GIC=y +CONFIG_MIPS_L1_CACHE_SHIFT=5 +CONFIG_MIPS_L1_CACHE_SHIFT_5=y +CONFIG_MIPS_MT=y +CONFIG_MIPS_MT_FPAFF=y +CONFIG_MIPS_MT_SMP=y +# CONFIG_MIPS_NO_APPENDED_DTB is not set +CONFIG_MIPS_NR_CPU_NR_MAP=4 +CONFIG_MIPS_PERF_SHARED_TC_COUNTERS=y +CONFIG_MIPS_RAW_APPENDED_DTB=y +CONFIG_MIPS_SPRAM=y +CONFIG_MMU_LAZY_TLB_REFCOUNT=y +CONFIG_MODULES_USE_ELF_REL=y +CONFIG_MODULE_FORCE_UNLOAD=y +CONFIG_MTD_CMDLINE_PARTS=y +CONFIG_MTD_SPI_NOR=y +CONFIG_MTD_SPI_NOR_USE_4K_SECTORS=y +CONFIG_MTD_SPLIT_FIT_FW=y +CONFIG_MTD_SPLIT_UIMAGE_FW=y +CONFIG_NEED_DMA_MAP_STATE=y +CONFIG_NEED_SRCU_NMI_SAFE=y +CONFIG_NET_DEVLINK=y +CONFIG_NET_DSA=y +CONFIG_NET_DSA_TAG_NONE=y +CONFIG_NET_EGRESS=y +CONFIG_NET_FLOW_LIMIT=y +CONFIG_NET_INGRESS=y +CONFIG_NET_PTP_CLASSIFY=y +CONFIG_NET_SELFTESTS=y +CONFIG_NET_SWITCHDEV=y +CONFIG_NET_XGRESS=y +CONFIG_NLS=y +CONFIG_NO_EXCEPT_FILL=y +CONFIG_NO_GENERIC_PCI_IOPORT_MAP=y +CONFIG_NO_HZ_COMMON=y +CONFIG_NO_HZ_IDLE=y +CONFIG_NR_CPUS=4 +CONFIG_NVMEM=y +CONFIG_NVMEM_LAYOUTS=y +CONFIG_NVMEM_SYSFS=y +CONFIG_OF=y +CONFIG_OF_ADDRESS=y +CONFIG_OF_EARLY_FLATTREE=y +CONFIG_OF_FLATTREE=y +CONFIG_OF_GPIO=y +CONFIG_OF_IRQ=y +CONFIG_OF_KOBJ=y +CONFIG_OF_MDIO=y +CONFIG_PADATA=y +CONFIG_PAGE_POOL=y +CONFIG_PAGE_SIZE_LESS_THAN_256KB=y +CONFIG_PAGE_SIZE_LESS_THAN_64KB=y +CONFIG_PCI_DRIVERS_LEGACY=y +CONFIG_PCS_XPCS=y +CONFIG_PERF_USE_VMALLOC=y +CONFIG_PGTABLE_LEVELS=2 +CONFIG_PHYLIB=y +CONFIG_PHYLIB_LEDS=y +CONFIG_PHYLINK=y +# CONFIG_PHY_SF19A2890_USB is not set +CONFIG_PINCTRL=y +CONFIG_PINCTRL_SF19A2890=y +# CONFIG_PINCTRL_SINGLE is not set +CONFIG_POSIX_MQUEUE=y +CONFIG_POSIX_MQUEUE_SYSCTL=y +CONFIG_POWER_RESET=y +CONFIG_POWER_RESET_SYSCON=y +CONFIG_POWER_SUPPLY=y +CONFIG_PPS=y +CONFIG_PREEMPT_NONE_BUILD=y +CONFIG_PRINTK_TIME=y +CONFIG_PROC_EVENTS=y +CONFIG_PTP_1588_CLOCK=y +CONFIG_PTP_1588_CLOCK_OPTIONAL=y +CONFIG_QUEUED_RWLOCKS=y +CONFIG_QUEUED_SPINLOCKS=y +CONFIG_RANDSTRUCT_NONE=y +CONFIG_RATIONAL=y +CONFIG_REGMAP=y +CONFIG_REGMAP_MMIO=y +CONFIG_REGULATOR=y +CONFIG_REGULATOR_FIXED_VOLTAGE=y +CONFIG_RESET_CONTROLLER=y +CONFIG_RESET_SF19A2890_PERIPH=y +CONFIG_RFS_ACCEL=y +CONFIG_RPS=y +CONFIG_SCHEDSTATS=y +CONFIG_SCHED_INFO=y +# CONFIG_SERIAL_8250 is not set +CONFIG_SERIAL_AMBA_PL011=y +CONFIG_SERIAL_AMBA_PL011_CONSOLE=y +CONFIG_SMP=y +CONFIG_SMP_UP=y +CONFIG_SOCK_RX_QUEUE_MAPPING=y +CONFIG_SPI=y +CONFIG_SPI_MASTER=y +CONFIG_SPI_MEM=y +CONFIG_SPI_PL022=y +CONFIG_SQUASHFS_DECOMP_MULTI_PERCPU=y +CONFIG_SRAM=y +CONFIG_STACKPROTECTOR=y +CONFIG_STMMAC_ETH=y +CONFIG_STMMAC_PLATFORM=y +CONFIG_SWPHY=y +CONFIG_SYNC_R4K=y +CONFIG_SYSCTL_EXCEPTION_TRACE=y +CONFIG_SYS_HAS_CPU_MIPS32_R2=y +CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y +CONFIG_SYS_SUPPORTS_ARBIT_HZ=y +CONFIG_SYS_SUPPORTS_HOTPLUG_CPU=y +CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y +CONFIG_SYS_SUPPORTS_MIPS16=y +CONFIG_SYS_SUPPORTS_MIPS_CPS=y +CONFIG_SYS_SUPPORTS_MULTITHREADING=y +CONFIG_SYS_SUPPORTS_SCHED_SMT=y +CONFIG_SYS_SUPPORTS_SMP=y +CONFIG_TARGET_ISA_REV=2 +CONFIG_TICK_CPU_ACCOUNTING=y +CONFIG_TIMER_OF=y +CONFIG_TIMER_PROBE=y +CONFIG_TREE_RCU=y +CONFIG_TREE_SRCU=y +CONFIG_USB_SUPPORT=y +CONFIG_USE_OF=y +CONFIG_WATCHDOG_CORE=y +CONFIG_WEAK_ORDERING=y +CONFIG_WERROR=y +CONFIG_XPS=y diff --git a/target/linux/siflower/sf19a2890/target.mk b/target/linux/siflower/sf19a2890/target.mk new file mode 100644 index 0000000000..6c47709895 --- /dev/null +++ b/target/linux/siflower/sf19a2890/target.mk @@ -0,0 +1,12 @@ +ARCH:=mipsel +SUBTARGET:=sf19a2890 +BOARDNAME:=Siflower SF19A2890 based boards +FEATURES+=fpu +CPU_TYPE:=24kc +CPU_SUBTYPE:=24kf + +KERNELNAME:=vmlinux + +define Target/Description + Build firmware images for Siflower SF19A2890 based boards. +endef