From: Pawel Dembicki Date: Wed, 11 Dec 2019 20:54:24 +0000 (+0100) Subject: ramips: mt7621: add support for Netgear R6800 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=4e9317201d3fb47800b387d69d79c00f38d2dbfd;p=openwrt%2Fstaging%2Fynezz.git ramips: mt7621: add support for Netgear R6800 This patch adds support for the Netgear R6800, aka Netgear AC1900 and R6800-100PES. Specification: - SoC: MediaTek MT7621AT (880 MHz) - Flash: 128 MiB NAND - RAM: 256 MiB - Wireless: MediaTek MT7615EN b/g/n , MediaTek MT7615EN an+ac - LAN speed: 10/100/1000 - LAN ports: 4 - WAN speed: 10/100/1000 - WAN ports: 1 - USB 2.0 - USB 3.0 - Serial baud rate of Bootloader and factory firmware: 57600 Known issues: - Device has 3 wifi LEDs: Wifi 5Ghz, Wifi 2.4Ghz and Wifi on/off. Wifi on/off is not used. Installation: - apply factory image via stock web-gui. Back to stock: - nmrpflash can be used to recover to the stock Netgear firmware. Signed-off-by: Pawel Dembicki --- diff --git a/target/linux/ramips/dts/mt7621_netgear_r6800.dts b/target/linux/ramips/dts/mt7621_netgear_r6800.dts new file mode 100644 index 0000000000..fed7bbba38 --- /dev/null +++ b/target/linux/ramips/dts/mt7621_netgear_r6800.dts @@ -0,0 +1,124 @@ +// SPDX-License-Identifier: GPL-2.0 +/dts-v1/; + +#include "mt7621_netgear_sercomm_bzv.dtsi" + +/ { + compatible = "netgear,r6800", "mediatek,mt7621-soc"; + model = "Netgear R6800"; + + aliases { + led-boot = &led_power_white; + led-failsafe = &led_power_orange; + led-running = &led_power_white; + led-upgrade = &led_power_orange; + label-mac-device = ðernet; + }; + + leds { + compatible = "gpio-leds"; + + led_power_orange: power_orange { + gpios = <&gpio_expander 0 GPIO_ACTIVE_LOW>; + label = "r6800:orange:power"; + }; + + led_power_white: power_white { + gpios = <&gpio_expander 1 GPIO_ACTIVE_LOW>; + label = "r6800:white:power"; + }; + + wan_orange { + gpios = <&gpio_expander 2 GPIO_ACTIVE_LOW>; + label = "r6800:orange:wan"; + }; + + wan_white { + gpios = <&gpio_expander 3 GPIO_ACTIVE_LOW>; + label = "r6800:white:wan"; + }; + + wlan2g { + gpios = <&gpio_expander 4 GPIO_ACTIVE_LOW>; + label = "r6800:white:wlan2g"; + linux,default-trigger = "phy0radio"; + }; + + wlan5g { + gpios = <&gpio_expander 5 GPIO_ACTIVE_LOW>; + label = "r6800:white:wlan5g"; + linux,default-trigger = "phy1radio"; + }; + + usb2 { + gpios = <&gpio_expander 6 GPIO_ACTIVE_LOW>; + label = "r6800:white:usb2"; + linux,default-trigger = "usbport"; + trigger-sources = <&ehci_port2>; + }; + + usb3 { + gpios = <&gpio_expander 7 GPIO_ACTIVE_LOW>; + label = "r6800:white:usb3"; + linux,default-trigger = "usbport"; + trigger-sources = <&xhci_ehci_port1>; + }; + + lan1_orange { + gpios = <&gpio_expander 8 GPIO_ACTIVE_LOW>; + label = "r6800:orange:lan1"; + }; + + lan1_white { + gpios = <&gpio_expander 9 GPIO_ACTIVE_LOW>; + label = "r6800:white:lan1"; + }; + + lan2_orange { + gpios = <&gpio_expander 10 GPIO_ACTIVE_LOW>; + label = "r6800:orange:lan2"; + }; + + lan2_white { + gpios = <&gpio_expander 11 GPIO_ACTIVE_LOW>; + label = "r6800:white:lan2"; + }; + + lan3_orange { + gpios = <&gpio_expander 12 GPIO_ACTIVE_LOW>; + label = "r6800:orange:lan3"; + }; + + lan3_white { + gpios = <&gpio_expander 13 GPIO_ACTIVE_LOW>; + label = "r6800:white:lan3"; + }; + + lan4_orange { + gpios = <&gpio_expander 14 GPIO_ACTIVE_LOW>; + label = "r6800:orange:lan4"; + }; + + lan4_white { + gpios = <&gpio_expander 15 GPIO_ACTIVE_LOW>; + label = "r6800:white:lan4"; + }; + + wps { + gpios = <&gpio0 17 GPIO_ACTIVE_HIGH>; + label = "r6800:white:wps"; + }; + + wlan { + gpios = <&gpio0 5 GPIO_ACTIVE_LOW>; + label = "r6800:white:wlan"; + }; + }; +}; + +&state_default { + gpio { + ralink,group = "uart3", "uart2", "jtag", "wdt"; + ralink,function = "gpio"; + }; +}; diff --git a/target/linux/ramips/dts/mt7621_netgear_sercomm_bzv.dtsi b/target/linux/ramips/dts/mt7621_netgear_sercomm_bzv.dtsi new file mode 100644 index 0000000000..6538b6926e --- /dev/null +++ b/target/linux/ramips/dts/mt7621_netgear_sercomm_bzv.dtsi @@ -0,0 +1,125 @@ +// SPDX-License-Identifier: GPL-2.0 + +#include "mt7621.dtsi" + +#include +#include + +/ { + compatible = "mediatek,mt7621-soc"; + + chosen { + bootargs = "console=ttyS0,57600"; + }; + + keys { + compatible = "gpio-keys"; + + wps { + label = "wps"; + gpios = <&gpio0 18 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + rfkill { + label = "rfkill"; + gpios = <&gpio0 14 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + reset { + label = "reset"; + gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; +}; + +&pcie { + status = "okay"; +}; + +&pcie0 { + wifi@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0 0 0 0 0>; + mediatek,mtd-eeprom = <&factory 0x0>; + ieee80211-freq-limit = <2400000 2500000>; + }; +}; + +&pcie1 { + wifi@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0 0 0 0 0>; + mediatek,mtd-eeprom = <&factory 0x8000>; + ieee80211-freq-limit = <5000000 6000000>; + }; +}; + +ðernet { + mtd-mac-address = <&factory 0x4>; +}; + +&i2c { + status = "okay"; + + gpio_expander: i2c0gpio-expander@20{ + #gpio-cells = <2>; + #interrupt-cells = <2>; + compatible = "semtech,sx1503q"; + reg = <0x20>; + + gpio-controller; + }; +}; + +&nand { + status = "okay"; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x100000>; + read-only; + }; + + partition@100000 { + label = "SC PART_MAP"; + reg = <0x100000 0x100000>; + read-only; + }; + + partition@200000 { + label = "kernel"; + reg = <0x200000 0x400000>; + }; + + partition@600000 { + label = "ubi"; + reg = <0x600000 0x2800000>; + }; + + partition@2e00000 { + label = "reserved0"; + reg = <0x2e00000 0x1800000>; + read-only; + }; + + factory: partition@4600000 { + label = "factory"; + reg = <0x4600000 0x200000>; + read-only; + }; + + partition@4800000 { + label = "reserved1"; + reg = <0x4800000 0x3800000>; + read-only; + }; + }; +}; diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk index 4c27cdbd31..82fbd87df9 100644 --- a/target/linux/ramips/image/mt7621.mk +++ b/target/linux/ramips/image/mt7621.mk @@ -595,6 +595,18 @@ define Device/netgear_r6350 endef TARGET_DEVICES += netgear_r6350 +define Device/netgear_r6800 + $(Device/netgear_sercomm_nand) + DEVICE_MODEL := R6800 + SERCOMM_HWNAME := R6950 + SERCOMM_HWID := BZV + SERCOMM_HWVER := A001 + SERCOMM_SWVER := 0x0062 + IMAGE_SIZE := 40960k + DEVICE_PACKAGES += kmod-mt7615e +endef +TARGET_DEVICES += netgear_r6800 + define Device/netgear_r6850 $(Device/netgear_sercomm_nand) DEVICE_MODEL := R6850 diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds b/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds index 4eab8f42fe..ac73729d1b 100755 --- a/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds @@ -52,6 +52,13 @@ netgear,r6850|\ netgear,wndr3700-v5) ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x10" ;; +netgear,r6800) + ucidef_set_led_switch "wan" "WAN" "$boardname:white:wan" "switch0" "0x10" + ucidef_set_led_switch "lan1" "LAN1" "$boardname:white:lan1" "switch0" "0x08" + ucidef_set_led_switch "lan2" "LAN2" "$boardname:white:lan2" "switch0" "0x04" + ucidef_set_led_switch "lan3" "LAN3" "$boardname:white:lan3" "switch0" "0x02" + ucidef_set_led_switch "lan4" "LAN4" "$boardname:white:lan4" "switch0" "0x01" + ;; tplink,re350-v1|\ tplink,re650-v1) ucidef_set_led_netdev "wifi2g" "Wifi 2.4G" "$boardname:blue:wifi2G" "wlan0" diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network index 9b7b56f0ba..a84ee808a3 100755 --- a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network +++ b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network @@ -41,6 +41,7 @@ ramips_setup_interfaces() netgear,r6220|\ netgear,r6260|\ netgear,r6350|\ + netgear,r6800|\ netgear,r6850|\ netgear,wndr3700-v5|\ netis,wf2881|\ @@ -252,6 +253,7 @@ ramips_setup_macs() ;; netgear,r6260|\ netgear,r6350|\ + netgear,r6800|\ netgear,r6850) wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 0x4)" 2) ;; diff --git a/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh b/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh index 465ea0a909..f6b5c86431 100755 --- a/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh +++ b/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh @@ -48,6 +48,7 @@ platform_do_upgrade() { netgear,r6220|\ netgear,r6260|\ netgear,r6350|\ + netgear,r6800|\ netgear,r6850|\ netis,wf2881|\ xiaomi,mir3g|\ diff --git a/target/linux/ramips/mt7621/config-4.14 b/target/linux/ramips/mt7621/config-4.14 index 4112cad780..2ae6afb97f 100644 --- a/target/linux/ramips/mt7621/config-4.14 +++ b/target/linux/ramips/mt7621/config-4.14 @@ -236,6 +236,7 @@ CONFIG_PHYLIB=y CONFIG_PINCTRL=y CONFIG_PINCTRL_RT2880=y # CONFIG_PINCTRL_SINGLE is not set +CONFIG_PINCTRL_SX150X=y CONFIG_POWER_RESET=y CONFIG_POWER_RESET_GPIO=y CONFIG_POWER_SUPPLY=y