From: Jan Alexander Date: Mon, 30 Nov 2020 10:51:16 +0000 (+0100) Subject: ipq806x: add support for Ubiquiti UniFi AC HD X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=4e46beb31342;p=openwrt%2Fstaging%2Flynxis.git ipq806x: add support for Ubiquiti UniFi AC HD Hardware -------- SoC: Qualcomm IPQ8064 RAM: 512MB DDR3 Flash: 256MB NAND (Micron MT29F2G08ABBEAH4) 32MB SPI-NOR (Macronix MX25U25635F) WLAN: Qualcomm Atheros QCA9994 4T4R b/g/n Qualcomm Atheros QCA9994 4T4R a/n/ac ETH: eth0 - SECONDARY (Atheros AR8033) eth1 - MAIN (Atheros AR8033) USB: USB-C LED: Dome (white / blue) BTN: Reset Installation ------------ Copy the OpenWrt sysupgrade image to the /tmp directory of the device using scp. Default IP address is 192.168.1.20 and default username and password are "ubnt". SSH to the device and write the bootselect flag to ensure it is booting from the mtd partition the OpenWrt image will be written to. Verify the output device below matches mtd partition "bootselect" using /proc/mtd. > dd if=/dev/zero bs=1 count=1 seek=7 conv=notrunc of=/dev/mtd11 Write the OpenWrt sysupgrade image to the mtd partition labeled "kernel0". Also verify the used partition device using /proc/mtd. > dd if=/tmp/sysupgrade.bin of=/dev/mtdblock12 Reboot the device. Back to stock ------------- Use the TFTP recovery procedure with the Ubiquiti firmware image to restore the vendor firmware. Signed-off-by: Jan Alexander --- diff --git a/package/boot/uboot-envtools/files/ipq806x b/package/boot/uboot-envtools/files/ipq806x index 6aae089ac4..96a4ee6450 100644 --- a/package/boot/uboot-envtools/files/ipq806x +++ b/package/boot/uboot-envtools/files/ipq806x @@ -45,6 +45,7 @@ qcom,ipq8064-ap148 |\ qcom,ipq8064-db149) ubootenv_add_uci_config $(ubootenv_mtdinfo) ;; +ubnt,unifi-ac-hd |\ zyxel,nbg6817) ubootenv_add_uci_config "/dev/mtdblock9" "0x0" "0x10000" "0x10000" ;; diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network index fbf56c5e0c..ddef4b7ac6 100755 --- a/target/linux/ipq806x/base-files/etc/board.d/02_network +++ b/target/linux/ipq806x/base-files/etc/board.d/02_network @@ -66,6 +66,9 @@ qcom,ipq8064-db149) ucidef_add_switch "switch0" \ "1:lan" "2:lan" "3:lan" "4:lan" "6u@eth1" "5:wan" "0u@eth0" ;; +ubnt,unifi-ac-hd) + ucidef_set_interface_lan "eth0 eth1" + ;; zyxel,nbg6817) hw_mac_addr=$(mtd_get_mac_ascii 0:APPSBLENV ethaddr) ucidef_add_switch "switch0" \ diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac b/target/linux/ipq806x/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac index f0256fd259..5af3a5b805 100644 --- a/target/linux/ipq806x/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac +++ b/target/linux/ipq806x/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac @@ -9,6 +9,14 @@ PHYNBR=${DEVPATH##*/phy} . /lib/functions.sh . /lib/functions/system.sh +board=$(board_name) + +case "$board" in + ubnt,unifi-ac-hd) + macaddr_add $(mtd_get_mac_binary EEPROM 0x6) $(($PHYNBR + 1)) > /sys${DEVPATH}/macaddress + ;; +esac + OPATH=${DEVPATH##/devices/platform/} OPATH=${OPATH%%/ieee*} diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-unifi-ac-hd.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-unifi-ac-hd.dts new file mode 100644 index 0000000000..c637da24a9 --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-unifi-ac-hd.dts @@ -0,0 +1,300 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qcom-ipq8064-v2.0.dtsi" + +#include +#include + +/ { + model = "Ubiquiti UniFi AC HD"; + compatible = "ubnt,unifi-ac-hd", "qcom,ipq8064"; + + aliases { + label-mac-device = &gmac2; + led-boot = &led_dome_white; + led-failsafe = &led_dome_white; + led-running = &led_dome_blue; + led-upgrade = &led_dome_blue; + mdio-gpio0 = &mdio0; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&led_pins>; + pinctrl-names = "default"; + + led_dome_blue: dome_blue { + label = "blue:dome"; + gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; + }; + + led_dome_white: dome_white { + label = "white:dome"; + gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; + }; + }; + + keys { + compatible = "gpio-keys"; + pinctrl-0 = <&button_pins>; + pinctrl-names = "default"; + + reset { + label = "reset"; + gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <60>; + }; + }; +}; + +&qcom_pinmux { + button_pins: button_pins { + mux { + pins = "gpio68"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + led_pins: led_pins { + mux { + pins = "gpio9", "gpio53"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + output-low; + }; + }; + + spi_pins: spi_pins { + mux { + pins = "gpio18", "gpio19", "gpio21"; + function = "gsbi5"; + drive-strength = <10>; + bias-none; + }; + + cs { + pins = "gpio20"; + drive-strength = <12>; + }; + }; +}; + +&CPU_SPC { + status = "disabled"; +}; + +&gsbi5 { + status = "okay"; + + qcom,mode = ; + + spi@1a280000 { + status = "okay"; + + pinctrl-0 = <&spi_pins>; + pinctrl-names = "default"; + cs-gpios = <&qcom_pinmux 20 0>; + + flash@0 { + compatible = "mx25u25635f", "jedec,spi-nor"; + #address-cells = <1>; + #size-cells = <1>; + spi-max-frequency = <50000000>; + reg = <0>; + m25p,fast-read; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "SBL1"; + reg = <0x0 0x20000>; + read-only; + }; + + partition@20000 { + label = "MIBIB"; + reg = <0x20000 0x10000>; + read-only; + }; + + partition@30000 { + label = "SBL2"; + reg = <0x30000 0x20000>; + read-only; + }; + + partition@50000 { + label = "SBL3"; + reg = <0x50000 0x30000>; + read-only; + }; + + partition@80000 { + label = "DDRCONFIG"; + reg = <0x80000 0x10000>; + read-only; + }; + + partition@90000 { + label = "SSD"; + reg = <0x90000 0x100000>; + read-only; + }; + + partition@a0000 { + label = "TZ"; + reg = <0xa0000 0x30000>; + read-only; + }; + + partition@d0000 { + label = "RPM"; + reg = <0xd0000 0x20000>; + read-only; + }; + + partition@f0000 { + label = "APPSBL"; + reg = <0xf0000 0xc0000>; + read-only; + }; + + partition@1b0000 { + label = "APPSBLENV"; + reg = <0x1b0000 0x10000>; + read-only; + }; + + eeprom: partition@1c0000 { + label = "EEPROM"; + reg = <0x1c0000 0x10000>; + read-only; + }; + + partition@1d0000 { + label = "bootselect"; + reg = <0x1d0000 0x10000>; + }; + + partition@1e0000 { + compatible = "denx,fit"; + label = "firmware"; + reg = <0x1e0000 0xe70000>; + }; + + partition@1050000 { + label = "kernel1"; + reg = <0x1050000 0xe70000>; + read-only; + }; + + partition@1ec0000 { + label = "debug"; + reg = <0x1ec0000 0x100000>; + read-only; + }; + + partition@1fc0000 { + label = "cfg"; + reg = <0x1fc0000 0x40000>; + read-only; + }; + }; + }; + }; +}; + +&adm_dma { + status = "okay"; +}; + +&nand_controller { + status = "okay"; + + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + nand-ecc-strength = <4>; + nand-bus-width = <8>; +}; + +&mdio0 { + status = "okay"; + + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; +}; + +&gmac2 { + status = "okay"; + + phy-mode = "sgmii"; + qcom,id = <2>; + qcom,emulation = <0>; + mdiobus = <&mdio0>; + + mtd-mac-address = <&eeprom 0x0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&gmac1 { + status = "okay"; + + phy-mode = "sgmii"; + qcom,id = <1>; + qcom,emulation = <0>; + mdiobus = <&mdio0>; + + mtd-mac-address = <&eeprom 0x6>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&pcie0 { + status = "okay"; +}; + +&pcie1 { + status = "okay"; +}; + +&tcsr { + status = "okay"; +}; + +&hs_phy_0 { + status = "okay"; +}; + +&ss_phy_0 { + status = "okay"; +}; + +&usb3_0 { + status = "okay"; +}; + +&hs_phy_1 { + status = "okay"; +}; + +&ss_phy_1 { + status = "okay"; +}; + +&usb3_1 { + status = "okay"; +}; diff --git a/target/linux/ipq806x/image/Makefile b/target/linux/ipq806x/image/Makefile index b77c0a99c0..bc917d4fa4 100644 --- a/target/linux/ipq806x/image/Makefile +++ b/target/linux/ipq806x/image/Makefile @@ -382,6 +382,18 @@ define Device/tplink_vr2600v endef TARGET_DEVICES += tplink_vr2600v +define Device/ubnt_unifi-ac-hd + $(call Device/FitImageLzma) + DEVICE_VENDOR := Ubiquiti + DEVICE_MODEL := UniFi AC HD + SOC := qcom-ipq8064 + BLOCKSIZE := 64k + IMAGE_SIZE := 14784k + DEVICE_PACKAGES := ath10k-firmware-qca9984-ct + IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | append-metadata | check-size +endef +TARGET_DEVICES += ubnt_unifi-ac-hd + define Device/zyxel_nbg6817 DEVICE_VENDOR := ZyXEL DEVICE_MODEL := NBG6817 diff --git a/target/linux/ipq806x/patches-5.4/0069-arm-boot-add-dts-files.patch b/target/linux/ipq806x/patches-5.4/0069-arm-boot-add-dts-files.patch index a5fce41112..055a4cbc30 100644 --- a/target/linux/ipq806x/patches-5.4/0069-arm-boot-add-dts-files.patch +++ b/target/linux/ipq806x/patches-5.4/0069-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -842,7 +842,23 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -842,7 +842,24 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-ipq4019-ap.dk04.1-c3.dtb \ qcom-ipq4019-ap.dk07.1-c1.dtb \ qcom-ipq4019-ap.dk07.1-c2.dtb \ @@ -25,6 +25,7 @@ Signed-off-by: John Crispin + qcom-ipq8064-g10.dtb \ + qcom-ipq8064-r7500.dtb \ + qcom-ipq8064-r7500v2.dtb \ ++ qcom-ipq8064-unifi-ac-hd.dtb \ + qcom-ipq8064-wg2600hp.dtb \ + qcom-ipq8064-wpq864.dtb \ + qcom-ipq8064-wxr-2533dhp.dtb \