From: Luka Perkov Date: Wed, 17 Feb 2016 17:49:26 +0000 (+0000) Subject: mvebu: add SolidRun ClearFog A1 support X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=4d966e4dde31aaa93023a643a128ea764b6d583b;p=openwrt%2Fstaging%2Fluka.git mvebu: add SolidRun ClearFog A1 support Signed-off-by: Andrej Vlasic SVN-Revision: 48736 --- diff --git a/target/linux/mvebu/base-files/etc/board.d/02_network b/target/linux/mvebu/base-files/etc/board.d/02_network index 289a4b0c01..f81d0ac172 100755 --- a/target/linux/mvebu/base-files/etc/board.d/02_network +++ b/target/linux/mvebu/base-files/etc/board.d/02_network @@ -31,6 +31,9 @@ armada-385-db-ap) armada-xp-gp) ucidef_set_interface_lan "eth0 eth1 eth2 eth3" ;; +armada-388-clearfog) + ucidef_set_interfaces_lan_wan "eth0 eth1" "eth2" + ;; *) ucidef_set_interface_lan "eth0" ;; diff --git a/target/linux/mvebu/base-files/lib/mvebu.sh b/target/linux/mvebu/base-files/lib/mvebu.sh index 09ebff3edc..836717d7f6 100755 --- a/target/linux/mvebu/base-files/lib/mvebu.sh +++ b/target/linux/mvebu/base-files/lib/mvebu.sh @@ -49,6 +49,9 @@ mvebu_board_detect() { *"Marvell Armada XP Development Board DB-MV784MP-GP") name="armada-xp-gp" ;; + *"SolidRun Clearfog A1") + name="armada-388-clearfog" + ;; esac [ -z "$name" ] && name="unknown" diff --git a/target/linux/mvebu/files/arch/arm/boot/dts/armada-388-clearfog.dts b/target/linux/mvebu/files/arch/arm/boot/dts/armada-388-clearfog.dts new file mode 100644 index 0000000000..c6e180eb3b --- /dev/null +++ b/target/linux/mvebu/files/arch/arm/boot/dts/armada-388-clearfog.dts @@ -0,0 +1,456 @@ +/* + * Device Tree file for SolidRun Clearfog revision A1 rev 2.0 (88F6828) + * + * Copyright (C) 2015 Russell King + * + * This board is in development; the contents of this file work with + * the A1 rev 2.0 of the board, which does not represent final + * production board. Things will change, don't expect this file to + * remain compatible info the future. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "armada-388.dtsi" +#include "armada-38x-solidrun-microsom.dtsi" + +/ { + model = "SolidRun Clearfog A1"; + compatible = "solidrun,clearfog-a1", "marvell,armada388", + "marvell,armada385", "marvell,armada380"; + + aliases { + /* So that mvebu u-boot can update the MAC addresses */ + ethernet1 = ð0; + ethernet2 = ð1; + ethernet3 = ð2; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + soc { + internal-regs { + ethernet@30000 { + phy-mode = "sgmii"; + status = "okay"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + ethernet@34000 { + phy-mode = "sgmii"; + status = "okay"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + i2c@11000 { + /* Is there anything on this? */ + clock-frequency = <100000>; + pinctrl-0 = <&i2c0_pins>; + pinctrl-names = "default"; + status = "okay"; + + /* + * PCA9655 GPIO expander, up to 1MHz clock. + * 0-CON3 CLKREQ# + * 1-CON3 PERST# + * 2-CON2 PERST# + * 3-CON3 W_DISABLE + * 4-CON2 CLKREQ# + * 5-USB3 overcurrent + * 6-USB3 power + * 7-CON2 W_DISABLE + * 8-JP4 P1 + * 9-JP4 P4 + * 10-JP4 P5 + * 11-m.2 DEVSLP + * 12-SFP_LOS + * 13-SFP_TX_FAULT + * 14-SFP_TX_DISABLE + * 15-SFP_MOD_DEF0 + */ + expander0: gpio-expander@20 { + /* + * This is how it should be: + * compatible = "onnn,pca9655", + * "nxp,pca9555"; + * but you can't do this because of + * the way I2C works. + */ + compatible = "nxp,pca9555"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x20>; + + pcie1_0_clkreq { + gpio-hog; + gpios = <0 GPIO_ACTIVE_LOW>; + input; + line-name = "pcie1.0-clkreq"; + }; + pcie1_0_w_disable { + gpio-hog; + gpios = <3 GPIO_ACTIVE_LOW>; + output-low; + line-name = "pcie1.0-w-disable"; + }; + pcie2_0_clkreq { + gpio-hog; + gpios = <4 GPIO_ACTIVE_LOW>; + input; + line-name = "pcie2.0-clkreq"; + }; + pcie2_0_w_disable { + gpio-hog; + gpios = <7 GPIO_ACTIVE_LOW>; + output-low; + line-name = "pcie2.0-w-disable"; + }; + usb3_ilimit { + gpio-hog; + gpios = <5 GPIO_ACTIVE_LOW>; + input; + line-name = "usb3-current-limit"; + }; + usb3_power { + gpio-hog; + gpios = <6 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "usb3-power"; + }; + m2_devslp { + gpio-hog; + gpios = <11 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "m.2 devslp"; + }; + sfp_los { + /* SFP loss of signal */ + gpio-hog; + gpios = <12 GPIO_ACTIVE_HIGH>; + input; + line-name = "sfp-los"; + }; + sfp_tx_fault { + /* SFP laser fault */ + gpio-hog; + gpios = <13 GPIO_ACTIVE_HIGH>; + input; + line-name = "sfp-tx-fault"; + }; + sfp_tx_disable { + /* SFP transmit disable */ + gpio-hog; + gpios = <14 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "sfp-tx-disable"; + }; + sfp_mod_def0 { + /* SFP module present */ + gpio-hog; + gpios = <15 GPIO_ACTIVE_LOW>; + input; + line-name = "sfp-mod-def0"; + }; + }; + + /* The MCP3021 is 100kHz clock only */ + mikrobus_adc: mcp3021@4c { + compatible = "microchip,mcp3021"; + reg = <0x4c>; + }; + + /* Also something at 0x64 */ + }; + + i2c@11100 { + /* + * Routed to SFP, mikrobus, and PCIe. + * SFP limits this to 100kHz, and requires + * an AT24C01A/02/04 with address pins tied + * low, which takes addresses 0x50 and 0x51. + * Mikrobus doesn't specify beyond an I2C + * bus being present. + * PCIe uses ARP to assign addresses, or + * 0x63-0x64. + */ + clock-frequency = <100000>; + pinctrl-0 = <&clearfog_i2c1_pins>; + pinctrl-names = "default"; + status = "okay"; + }; + + mdio@72004 { + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + + phy_dedicated: ethernet-phy@0 { + /* + * Annoyingly, the marvell phy driver + * configures the LED register, rather + * than preserving reset-loaded setting. + * We undo that rubbish here. + */ + marvell,reg-init = <3 16 0 0x101e>; + reg = <0>; + }; + }; + + pinctrl@18000 { + clearfog_dsa0_clk_pins: clearfog-dsa0-clk-pins { + marvell,pins = "mpp46"; + marvell,function = "ref"; + }; + clearfog_dsa0_pins: clearfog-dsa0-pins { + marvell,pins = "mpp23", "mpp41"; + marvell,function = "gpio"; + }; + clearfog_i2c1_pins: i2c1-pins { + /* SFP, PCIe, mSATA, mikrobus */ + marvell,pins = "mpp26", "mpp27"; + marvell,function = "i2c1"; + }; + clearfog_sdhci_cd_pins: clearfog-sdhci-cd-pins { + marvell,pins = "mpp20"; + marvell,function = "gpio"; + }; + clearfog_sdhci_pins: clearfog-sdhci-pins { + marvell,pins = "mpp21", "mpp28", + "mpp37", "mpp38", + "mpp39", "mpp40"; + marvell,function = "sd0"; + }; + clearfog_spi1_cs_pins: spi1-cs-pins { + marvell,pins = "mpp55"; + marvell,function = "spi1"; + }; + mikro_pins: mikro-pins { + /* int: mpp22 rst: mpp29 */ + marvell,pins = "mpp22", "mpp29"; + marvell,function = "gpio"; + }; + mikro_spi_pins: mikro-spi-pins { + marvell,pins = "mpp43"; + marvell,function = "spi1"; + }; + mikro_uart_pins: mikro-uart-pins { + marvell,pins = "mpp24", "mpp25"; + marvell,function = "ua1"; + }; + rear_button_pins: rear-button-pins { + marvell,pins = "mpp34"; + marvell,function = "gpio"; + }; + }; + + sata@a8000 { + /* pinctrl? */ + status = "okay"; + }; + + sata@e0000 { + /* pinctrl? */ + status = "okay"; + }; + + sdhci@d8000 { + bus-width = <4>; + cd-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>; + no-1-8-v; + pinctrl-0 = <&clearfog_sdhci_pins + &clearfog_sdhci_cd_pins>; + pinctrl-names = "default"; + status = "okay"; + vmmc = <®_3p3v>; + wp-inverted; + }; + + serial@12100 { + /* mikrobus uart */ + pinctrl-0 = <&mikro_uart_pins>; + pinctrl-names = "default"; + status = "okay"; + }; + + spi@10680 { + /* + * We don't seem to have the W25Q32 on the + * A1 Rev 2.0 boards, so disable SPI. + * CS0: W25Q32 (doesn't appear to be present) + * CS1: + * CS2: mikrobus + */ + pinctrl-0 = <&spi1_pins + &clearfog_spi1_cs_pins + &mikro_spi_pins>; + pinctrl-names = "default"; + status = "okay"; + + spi-flash@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "w25q32", "jedec,spi-nor"; + reg = <0>; /* Chip select 0 */ + spi-max-frequency = <3000000>; + status = "disabled"; + }; + }; + + usb@58000 { + /* CON3, nearest power. */ + status = "okay"; + }; + + usb3@f0000 { + /* CON2, nearest CPU, USB2 only. */ + status = "okay"; + }; + + usb3@f8000 { + /* CON7 */ + status = "okay"; + }; + }; + + pcie-controller { + status = "okay"; + /* + * The two PCIe units are accessible through + * the mini-PCIe connectors on the board. + */ + pcie@2,0 { + /* Port 1, Lane 0. CON3, nearest power. */ + reset-gpios = <&expander0 1 GPIO_ACTIVE_LOW>; + status = "okay"; + }; + pcie@3,0 { + /* Port 2, Lane 0. CON2, nearest CPU. */ + reset-gpios = <&expander0 2 GPIO_ACTIVE_LOW>; + status = "okay"; + }; + }; + }; + + dsa@0 { + compatible = "marvell,dsa"; + dsa,ethernet = <ð1>; + dsa,mii-bus = <&mdio>; + pinctrl-0 = <&clearfog_dsa0_clk_pins &clearfog_dsa0_pins>; + pinctrl-names = "default"; + #address-cells = <2>; + #size-cells = <0>; + + switch@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <4 0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@3 { + reg = <3>; + label = "lan4"; + }; + + port@4 { + reg = <4>; + label = "lan5"; + }; + + port@5 { + reg = <5>; + label = "cpu"; + }; + + port@6 { + /* 88E1512 external phy */ + reg = <6>; + label = "lan6"; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-0 = <&rear_button_pins>; + pinctrl-names = "default"; + + button_0 { + /* The rear SW3 button */ + label = "Rear Button"; + gpios = <&gpio1 2 GPIO_ACTIVE_LOW>; + linux,can-disable; + linux,code = ; + }; + }; +}; diff --git a/target/linux/mvebu/files/arch/arm/boot/dts/armada-38x-solidrun-microsom.dtsi b/target/linux/mvebu/files/arch/arm/boot/dts/armada-38x-solidrun-microsom.dtsi new file mode 100644 index 0000000000..3f792a563c --- /dev/null +++ b/target/linux/mvebu/files/arch/arm/boot/dts/armada-38x-solidrun-microsom.dtsi @@ -0,0 +1,115 @@ +/* + * Device Tree file for SolidRun Armada 38x Microsom + * + * Copyright (C) 2015 Russell King + * + * This board is in development; the contents of this file work with + * the A1 rev 2.0 of the board, which does not represent final + * production board. Things will change, don't expect this file to + * remain compatible info the future. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ +#include +#include + +/ { + memory { + device_type = "memory"; + reg = <0x00000000 0x10000000>; /* 256 MB */ + }; + + soc { + ranges = ; + + internal-regs { + ethernet@70000 { + pinctrl-0 = <&ge0_rgmii_pins>; + pinctrl-names = "default"; + phy = <&phy_dedicated>; + phy-mode = "rgmii-id"; + status = "okay"; + }; + + mdio@72004 { + /* + * Add the phy clock here, so the phy can be + * accessed to read its IDs prior to binding + * with the driver. + */ + pinctrl-0 = <&mdio_pins µsom_phy_clk_pins>; + pinctrl-names = "default"; + + phy_dedicated: ethernet-phy@0 { + /* + * Annoyingly, the marvell phy driver + * configures the LED register, rather + * than preserving reset-loaded setting. + * We undo that rubbish here. + */ + marvell,reg-init = <3 16 0 0x101e>; + reg = <0>; + }; + }; + + pinctrl@18000 { + microsom_phy_clk_pins: microsom-phy-clk-pins { + marvell,pins = "mpp45"; + marvell,function = "ref"; + }; + }; + + rtc@a3800 { + /* + * If the rtc doesn't work, run "date reset" + * twice in u-boot. + */ + status = "okay"; + }; + + serial@12000 { + pinctrl-0 = <&uart0_pins>; + pinctrl-names = "default"; + status = "okay"; + }; + }; + }; +}; diff --git a/target/linux/mvebu/image/Makefile b/target/linux/mvebu/image/Makefile index 123be9eac2..cb73c3bea6 100644 --- a/target/linux/mvebu/image/Makefile +++ b/target/linux/mvebu/image/Makefile @@ -97,6 +97,26 @@ define NORProfile PROFILES_LIST += $(1) endef +# $(1): Profile Name +# $(2): DTB Name +define MMCProfile + define Image/BuildKernel/Profile/$(1) + $(call Image/Build/DTB,$(2)) + cp $(KDIR)/zImage-$(2) $(BIN_DIR)/zImage-$(1); + cp $(DTS_DIR)/$(2).dtb $(BIN_DIR)/$(1).dtb; + ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),) + $(call Image/Build/Profile,$(1)/Initramfs) + endif + endef + + define Image/Build/Profile/$(1)/Initramfs + $(call Image/Build/DTB,$(2),-initramfs) + cp $(KDIR)/uImage-initramfs-$(2) $(BIN_DIR)/$(IMG_PREFIX)-$(2)-initramfs + endef + + PROFILES_LIST += $(1) +endef + # $(1): Profile Name # $(2): Sub Profiles list define MultiProfile @@ -141,6 +161,8 @@ $(eval $(call UBINORProfile,OpenBlocks-AX-3-4,armada-xp-openblocks-ax3-4,128KiB) # Boards with small NOR, where UBI doesn't make sense $(eval $(call NORProfile,388-RD,armada-388-rd,256KiB)) +$(eval $(call MMCProfile,Solidrun-Clearfog-A1,armada-388-clearfog)) + ### ### Linksys ### diff --git a/target/linux/mvebu/patches-4.1/209-solidrun_clearfog.patch b/target/linux/mvebu/patches-4.1/209-solidrun_clearfog.patch new file mode 100644 index 0000000000..5e8c89bc4b --- /dev/null +++ b/target/linux/mvebu/patches-4.1/209-solidrun_clearfog.patch @@ -0,0 +1,10 @@ +--- a/arch/arm/boot/dts/Makefile ++++ b/arch/arm/boot/dts/Makefile +@@ -636,6 +636,7 @@ dtb-$(CONFIG_MACH_ARMADA_38X) += \ + armada-385-linksys-caiman.dtb \ + armada-385-linksys-cobra.dtb \ + armada-385-linksys-shelby.dtb \ ++ armada-388-clearfog.dtb \ + armada-388-db.dtb \ + armada-388-gp.dtb \ + armada-388-rd.dtb diff --git a/target/linux/mvebu/patches-4.4/209-solidrun_clearfog.patch b/target/linux/mvebu/patches-4.4/209-solidrun_clearfog.patch new file mode 100644 index 0000000000..80a09465bd --- /dev/null +++ b/target/linux/mvebu/patches-4.4/209-solidrun_clearfog.patch @@ -0,0 +1,10 @@ +--- a/arch/arm/boot/dts/Makefile ++++ b/arch/arm/boot/dts/Makefile +@@ -749,6 +749,7 @@ dtb-$(CONFIG_MACH_ARMADA_38X) += \ + armada-385-linksys-caiman.dtb \ + armada-385-linksys-cobra.dtb \ + armada-385-linksys-shelby.dtb \ ++ armada-388-clearfog.dtb \ + armada-388-db.dtb \ + armada-388-gp.dtb \ + armada-388-rd.dtb diff --git a/target/linux/mvebu/profiles/solidrun.mk b/target/linux/mvebu/profiles/solidrun.mk new file mode 100644 index 0000000000..5aa61e28a2 --- /dev/null +++ b/target/linux/mvebu/profiles/solidrun.mk @@ -0,0 +1,21 @@ +# +# Copyright (C) 2016 OpenWrt.org +# +# This is free software, licensed under the GNU General Public License v2. +# See /LICENSE for more information. +# + +define Profile/Solidrun-Clearfog-A1 + NAME:=SolidRun ClearFog A1 board + PACKAGES:= \ + kmod-usb3 kmod-usb2 kmod-usb-storage \ + kmod-of-i2c kmod-i2c-core kmod-i2c-mv64xxx \ + kmod-ata-core kmod-ata-marvell-sata \ + kmod-thermal-armada kmod-rtc-marvell +endef + +define Profile/Solidrun-Clearfog-A1/Description + Package set compatible with the SolidRun ClearFog A1 board +endef + +$(eval $(call Profile,Solidrun-Clearfog-A1))