From: Thomas Kupper Date: Fri, 5 May 2023 15:04:33 +0000 (+0200) Subject: ipq807x: add support for Netgear RAX120v2 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=4d79a65d607c471eab04a3821000d1a37440da33;p=openwrt%2Fstaging%2Fthess.git ipq807x: add support for Netgear RAX120v2 Netgear Nighthawk RAX120v2 AX WIFI router with 5 1G and 1 5G ports. The majority of the code is based on @jewwest's PR #11830. Specifications: * CPU: Qualcomm IPQ8074 Quad core Cortex-A53 2.2GHz * RAM: 1024MB of DDR3 (Nanya NT5CC256M16EP-EK × 2) * Flash: SPI-NAND 512 MiB (Winbond W29N04GZBIBA) * Ethernet: 4x 10/100/1000 Mbps LAN, 1x 10/100/1000 Mbps WAN (Qualcomm QCA8075), 1x 10/100/1000/2500/5000 Mbps LAN/WAN (Aquantia AQR111B0 PHY) * Wi-Fi: * 2.4 GHz: Qualcomm QCN5024 4x4 * 2x 5 GHz: Qualcomm QCN5054 4x4 * USB: 2x USB 3.0 * LEDs: Power, 2.4GHz & 5GHz Radio, WPS, WAN, USB1 & USB2, 5G LAN * Keys: LEDs On/Off, Power, Reset, RFKILL, WPS * UART: Marked J9003 VCC TX RX GND, beginning from "1". 3.3v, 115200n8 * Power: 19 VDC, 3.1 A Installation: * Flashing OpenWrt is done in two steps: a) Flash *-squashfs-web-ui-factory.img from stock UI (thanks to @wangyu-). This writes an initramfs based OpenWrt image onto the RAX120v2 b) From OpenWrt flash the *-squashfs-sysupgrade.bin using LuCI or the commandline * U-Boot allows booting an initramfs image via TFTP: - Set ip of your PC to 192.168.1.100 - At the serial console interrupt boot at "Hit any key to stop autoboot:" - In u-boot run `tftpsrv` - On your PC send the OpenWrt initramfs image: tftp 192.168.1.1 -m binary -c put openwrt-ipq807x-generic-netgear_rax120v2-initramfs-uImage.itb Make 5G Aquantia phy work: For the 5G port labeled 'lan5' to work a firmware is needed. This can be loaded in u-boot by writing the firmware to the correct mtd partition. The firmware file found in the Netgear stock firmware under /lib/firmware/ named 'AQR-G3_v4.3.C-AQR_DNI_DR-EQ35AX8-R-prov1_ID23888_VER1311.cld' is needed and has to be converted to a MBN file. The `mkheader.py` script used here can be found in the Netgear V1.2.8.40 GPL source, under 'git_home/u-boot.git/tools/mkheader.py' Convert the CLD file to MBN using: $ python2 mkheader.py 0x44000000 0x13 <*.cld file> aqr_4.3.C.mbn This MBN file can then be flashed to the MTD partition to be used by u-boot. The necessary files can also be found in https://github.com/boretom/openwrt-fork/tree/rax120v2/aquantia-firmware * Write MBN file to MTD partition to be loaded automatically by u-boot: U-boot automatically tries to load the firmware from nand at address 0x7e00000 which corresponds to `/dev/mtd25` in OpenWrt. - find ETHPHYFW partition while running OpenWrt (expected: /dev/mtd25) $ fgrep -i 'ethphyfw' /proc/mtd mtd25: 00080000 00020000 "ethphyfw - copy mbn file to /tmp/ folder of the router $ scp aqr-v4.3.C.mbn 192.168.1.1:/tmp/ - write mbn file to ethphyfw partition $ mtd write /tmp/aqr_v4.3.C.mbn /dev/mtd25 Revert to stock firmware: * Flash the stock firmware to the bootloader using TFTP/NMRP. References to RAX120v2 GPL source: https://www.downloads.netgear.com/files/GPL/RAX120-V1.2.8.40_gpl_src.zip Reviewed-by: Robert Marko Signed-off-by: Thomas Kupper --- diff --git a/package/boot/uboot-envtools/files/qualcommax_ipq807x b/package/boot/uboot-envtools/files/qualcommax_ipq807x index 345cdadebe..297c727857 100644 --- a/package/boot/uboot-envtools/files/qualcommax_ipq807x +++ b/package/boot/uboot-envtools/files/qualcommax_ipq807x @@ -9,6 +9,7 @@ board=$(board_name) case "$board" in dynalink,dl-wrx36|\ +netgear,rax120v2|\ netgear,wax218) idx="$(find_mtd_index 0:appsblenv)" [ -n "$idx" ] && \ diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile index 1e4b3a95c2..aa1466418e 100644 --- a/package/firmware/ipq-wifi/Makefile +++ b/package/firmware/ipq-wifi/Makefile @@ -33,6 +33,7 @@ ALLWIFIBOARDS:= \ dynalink_dl-wrx36 \ edgecore_eap102 \ edimax_cax1800 \ + netgear_rax120v2 \ netgear_wax218 \ prpl_haze \ qnap_301w \ @@ -121,6 +122,7 @@ $(eval $(call generate-ipq-wifi-package,compex_wpq873,Compex WPQ-873)) $(eval $(call generate-ipq-wifi-package,dynalink_dl-wrx36,Dynalink DL-WRX36)) $(eval $(call generate-ipq-wifi-package,edgecore_eap102,Edgecore EAP102)) $(eval $(call generate-ipq-wifi-package,edimax_cax1800,Edimax CAX1800)) +$(eval $(call generate-ipq-wifi-package,netgear_rax120v2,Netgear RAX120v2)) $(eval $(call generate-ipq-wifi-package,netgear_wax218,Netgear WAX218)) $(eval $(call generate-ipq-wifi-package,qnap_301w,QNAP 301w)) $(eval $(call generate-ipq-wifi-package,prpl_haze,prpl Haze)) diff --git a/target/linux/generic/hack-5.15/726-net-phy-aquantia-enable-AQR111-and-AQR111B0.patch b/target/linux/generic/hack-5.15/726-net-phy-aquantia-enable-AQR111-and-AQR111B0.patch new file mode 100644 index 0000000000..e14a5f1747 --- /dev/null +++ b/target/linux/generic/hack-5.15/726-net-phy-aquantia-enable-AQR111-and-AQR111B0.patch @@ -0,0 +1,109 @@ +Author: Thomas Kupper +Date: Wed May 24 21:14:17 2023 +0200 + +kernel: phy: add Aquantia PHY AQR111 & AQR111B0 + +Add the IDs for Aquantia PHY AQR111 and AQR111B0 as found in the GPL sources +of the Netgear RAX120v2 firmware v1.2.8.40. + +This is a 5GbE chip but it reports support for 10G. Implement config_init() +to set max speed to 5G. + +Signed-off-by: Thomas Kupper +--- a/drivers/net/phy/aquantia_main.c ++++ b/drivers/net/phy/aquantia_main.c +@@ -20,6 +20,8 @@ + #define PHY_ID_AQR105 0x03a1b4a2 + #define PHY_ID_AQR106 0x03a1b4d0 + #define PHY_ID_AQR107 0x03a1b4e0 ++#define PHY_ID_AQR111 0x03a1b610 ++#define PHY_ID_AQR111B0 0x03a1b612 + #define PHY_ID_AQR112 0x03a1b662 + #define PHY_ID_AQR112C 0x03a1b790 + #define PHY_ID_AQR112R 0x31c31d12 +@@ -686,6 +688,33 @@ static int aqcs109_config_init(struct ph + return aqr107_set_downshift(phydev, MDIO_AN_VEND_PROV_DOWNSHIFT_DFLT); + } + ++static int aqr111_config_init(struct phy_device *phydev) ++{ ++ int ret; ++ ++ /* Check that the PHY interface type is compatible */ ++ if (phydev->interface != PHY_INTERFACE_MODE_SGMII && ++ phydev->interface != PHY_INTERFACE_MODE_2500BASEX && ++ phydev->interface != PHY_INTERFACE_MODE_XGMII && ++ phydev->interface != PHY_INTERFACE_MODE_USXGMII && ++ phydev->interface != PHY_INTERFACE_MODE_10GKR && ++ phydev->interface != PHY_INTERFACE_MODE_10GBASER) ++ return -ENODEV; ++ ++ WARN(phydev->interface == PHY_INTERFACE_MODE_XGMII, ++ "Your devicetree is out of date, please update it. The AQR107 family doesn't support XGMII, maybe you mean USXGMII.\n"); ++ ++ ret = aqr107_wait_reset_complete(phydev); ++ if (!ret) ++ aqr107_chip_info(phydev); ++ ++ /* AQR111 reports supporting speed up to 10G, however only speeds up to 5G are supported. */ ++ ret = phy_set_max_speed(phydev, SPEED_5000); ++ if (ret) ++ return ret; ++ ++ return aqr107_set_downshift(phydev, MDIO_AN_VEND_PROV_DOWNSHIFT_DFLT); ++} + static void aqr107_link_change_notify(struct phy_device *phydev) + { + u8 fw_major, fw_minor; +@@ -905,6 +934,42 @@ static struct phy_driver aqr_driver[] = + .link_change_notify = aqr107_link_change_notify, + }, + { ++ PHY_ID_MATCH_MODEL(PHY_ID_AQR111), ++ .name = "Aquantia AQR111", ++ .probe = aqr107_probe, ++ .config_init = aqr111_config_init, ++ .config_aneg = aqr_config_aneg, ++ .config_intr = aqr_config_intr, ++ .handle_interrupt = aqr_handle_interrupt, ++ .read_status = aqr107_read_status, ++ .get_tunable = aqr107_get_tunable, ++ .set_tunable = aqr107_set_tunable, ++ .suspend = aqr107_suspend, ++ .resume = aqr107_resume, ++ .get_sset_count = aqr107_get_sset_count, ++ .get_strings = aqr107_get_strings, ++ .get_stats = aqr107_get_stats, ++ .link_change_notify = aqr107_link_change_notify, ++}, ++{ ++ PHY_ID_MATCH_MODEL(PHY_ID_AQR111B0), ++ .name = "Aquantia AQR111B0", ++ .probe = aqr107_probe, ++ .config_init = aqr111_config_init, ++ .config_aneg = aqr_config_aneg, ++ .config_intr = aqr_config_intr, ++ .handle_interrupt = aqr_handle_interrupt, ++ .read_status = aqr107_read_status, ++ .get_tunable = aqr107_get_tunable, ++ .set_tunable = aqr107_set_tunable, ++ .suspend = aqr107_suspend, ++ .resume = aqr107_resume, ++ .get_sset_count = aqr107_get_sset_count, ++ .get_strings = aqr107_get_strings, ++ .get_stats = aqr107_get_stats, ++ .link_change_notify = aqr107_link_change_notify, ++}, ++{ + PHY_ID_MATCH_MODEL(PHY_ID_AQR112), + .name = "Aquantia AQR112", + .probe = aqr107_probe, +@@ -970,6 +1035,8 @@ static struct mdio_device_id __maybe_unu + { PHY_ID_MATCH_MODEL(PHY_ID_AQR105) }, + { PHY_ID_MATCH_MODEL(PHY_ID_AQR106) }, + { PHY_ID_MATCH_MODEL(PHY_ID_AQR107) }, ++ { PHY_ID_MATCH_MODEL(PHY_ID_AQR111) }, ++ { PHY_ID_MATCH_MODEL(PHY_ID_AQR111B0) }, + { PHY_ID_MATCH_MODEL(PHY_ID_AQR112) }, + { PHY_ID_MATCH_MODEL(PHY_ID_AQR112C) }, + { PHY_ID_MATCH_MODEL(PHY_ID_AQR112R) }, diff --git a/target/linux/generic/hack-6.1/726-net-phy-aquantia-enable-AQR111-and-AQR111B0.patch b/target/linux/generic/hack-6.1/726-net-phy-aquantia-enable-AQR111-and-AQR111B0.patch new file mode 100644 index 0000000000..dc25905fee --- /dev/null +++ b/target/linux/generic/hack-6.1/726-net-phy-aquantia-enable-AQR111-and-AQR111B0.patch @@ -0,0 +1,110 @@ +Author: Thomas Kupper +Date: Wed May 24 21:14:17 2023 +0200 + +kernel: phy: add Aquantia PHY AQR111 & AQR111B0 + +Add the IDs for Aquantia PHY AQR111 and AQR111B0 as found in the GPL sources +of the Netgear RAX120v2 firmware v1.2.8.40. + +This is a 5GbE chip but it reports support for 10G. Implement config_init() +to set max speed to 5G. + +Signed-off-by: Thomas Kupper +--- a/drivers/net/phy/aquantia_main.c ++++ b/drivers/net/phy/aquantia_main.c +@@ -24,6 +24,8 @@ + #define PHY_ID_AQR405 0x03a1b4b0 + #define PHY_ID_AQR113C 0x31c31c12 + #define PHY_ID_AQR813 0x31c31cb2 ++#define PHY_ID_AQR111 0x03a1b610 ++#define PHY_ID_AQR111B0 0x03a1b612 + #define PHY_ID_AQR112 0x03a1b662 + #define PHY_ID_AQR412 0x03a1b712 + #define PHY_ID_AQR113 0x31c31c40 +@@ -729,6 +731,34 @@ static int aqcs109_config_init(struct ph + return aqr107_set_downshift(phydev, MDIO_AN_VEND_PROV_DOWNSHIFT_DFLT); + } + ++static int aqr111_config_init(struct phy_device *phydev) ++{ ++ int ret; ++ ++ /* Check that the PHY interface type is compatible */ ++ if (phydev->interface != PHY_INTERFACE_MODE_SGMII && ++ phydev->interface != PHY_INTERFACE_MODE_1000BASEKX && ++ phydev->interface != PHY_INTERFACE_MODE_2500BASEX && ++ phydev->interface != PHY_INTERFACE_MODE_XGMII && ++ phydev->interface != PHY_INTERFACE_MODE_USXGMII && ++ phydev->interface != PHY_INTERFACE_MODE_10GKR && ++ phydev->interface != PHY_INTERFACE_MODE_10GBASER && ++ phydev->interface != PHY_INTERFACE_MODE_XAUI && ++ phydev->interface != PHY_INTERFACE_MODE_RXAUI) ++ return -ENODEV; ++ ++ WARN(phydev->interface == PHY_INTERFACE_MODE_XGMII, ++ "Your devicetree is out of date, please update it. The AQR107 family doesn't support XGMII, maybe you mean USXGMII.\n"); ++ ++ ret = aqr107_wait_reset_complete(phydev); ++ if (!ret) ++ aqr107_chip_info(phydev); ++ ++ /* AQR111 reports supporting speed up to 10G, however only speeds up to 5G are supported. */ ++ phy_set_max_speed(phydev, SPEED_5000); ++ ++ return aqr107_set_downshift(phydev, MDIO_AN_VEND_PROV_DOWNSHIFT_DFLT); ++} + static void aqr107_link_change_notify(struct phy_device *phydev) + { + u8 fw_major, fw_minor; +@@ -961,6 +991,42 @@ static struct phy_driver aqr_driver[] = + .link_change_notify = aqr107_link_change_notify, + }, + { ++ PHY_ID_MATCH_MODEL(PHY_ID_AQR111), ++ .name = "Aquantia AQR111", ++ .probe = aqr107_probe, ++ .config_init = aqr111_config_init, ++ .config_aneg = aqr_config_aneg, ++ .config_intr = aqr_config_intr, ++ .handle_interrupt = aqr_handle_interrupt, ++ .read_status = aqr107_read_status, ++ .get_tunable = aqr107_get_tunable, ++ .set_tunable = aqr107_set_tunable, ++ .suspend = aqr107_suspend, ++ .resume = aqr107_resume, ++ .get_sset_count = aqr107_get_sset_count, ++ .get_strings = aqr107_get_strings, ++ .get_stats = aqr107_get_stats, ++ .link_change_notify = aqr107_link_change_notify, ++}, ++{ ++ PHY_ID_MATCH_MODEL(PHY_ID_AQR111B0), ++ .name = "Aquantia AQR111B0", ++ .probe = aqr107_probe, ++ .config_init = aqr111_config_init, ++ .config_aneg = aqr_config_aneg, ++ .config_intr = aqr_config_intr, ++ .handle_interrupt = aqr_handle_interrupt, ++ .read_status = aqr107_read_status, ++ .get_tunable = aqr107_get_tunable, ++ .set_tunable = aqr107_set_tunable, ++ .suspend = aqr107_suspend, ++ .resume = aqr107_resume, ++ .get_sset_count = aqr107_get_sset_count, ++ .get_strings = aqr107_get_strings, ++ .get_stats = aqr107_get_stats, ++ .link_change_notify = aqr107_link_change_notify, ++}, ++{ + PHY_ID_MATCH_MODEL(PHY_ID_AQR112), + .name = "Aquantia AQR112", + .probe = aqr107_probe, +@@ -1030,6 +1096,8 @@ static struct mdio_device_id __maybe_unu + { PHY_ID_MATCH_MODEL(PHY_ID_AQR405) }, + { PHY_ID_MATCH_MODEL(PHY_ID_AQR113C) }, + { PHY_ID_MATCH_MODEL(PHY_ID_AQR813) }, ++ { PHY_ID_MATCH_MODEL(PHY_ID_AQR111) }, ++ { PHY_ID_MATCH_MODEL(PHY_ID_AQR111B0) }, + { PHY_ID_MATCH_MODEL(PHY_ID_AQR112) }, + { PHY_ID_MATCH_MODEL(PHY_ID_AQR412) }, + { PHY_ID_MATCH_MODEL(PHY_ID_AQR113) }, diff --git a/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8074-rax120v2.dts b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8074-rax120v2.dts new file mode 100644 index 0000000000..188ad03fe0 --- /dev/null +++ b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8074-rax120v2.dts @@ -0,0 +1,553 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +/dts-v1/; + +#include "ipq8074.dtsi" +#include "ipq8074-ess.dtsi" +#include "ipq8074-hk-cpu.dtsi" +#include +#include +#include + +/ { + model = "Netgear RAX120v2"; + compatible = "netgear,rax120v2", "qcom,ipq8074"; + + aliases { + serial0 = &blsp1_uart5; + + led-running = &led_system_white; + led-upgrade = &led_system_white; + led-internet = &led_wan_white; + label-mac-device = &dp1; + }; + + chosen { + stdout-path = "serial0:115200n8"; + bootargs-append = " ubi.mtd=rootfs root=/dev/ubiblock0_0"; + }; + + keys { + compatible = "gpio-keys"; + + rfkill { + label = "rfkill"; + gpios = <&tlmm 25 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&tlmm 57 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + reset { + label = "reset"; + gpios = <&tlmm 54 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + led_spi { + compatible = "spi-gpio"; + #address-cells = <1>; + #size-cells = <0>; + + sck-gpios = <&tlmm 18 GPIO_ACTIVE_HIGH>; + mosi-gpios = <&tlmm 19 GPIO_ACTIVE_HIGH>; + + led_gpio: led_gpio@0 { + compatible = "fairchild,74hc595"; + reg = <0>; + gpio-controller; + #gpio-cells = <2>; + registers-number = <2>; + enable-gpios = <&tlmm 20 GPIO_ACTIVE_HIGH>; + spi-max-frequency = <1000000>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_system_white: system-white { + label = "white:system"; + gpios = <&led_gpio 0 GPIO_ACTIVE_LOW>; + color = ; + }; + + led_24g_white { + label = "white:24g"; + gpios = <&led_gpio 1 GPIO_ACTIVE_LOW>; + color = ; + linux,default-trigger = "phy1radio"; + }; + + led_5g_white { + label = "white:5g"; + gpios = <&led_gpio 2 GPIO_ACTIVE_LOW>; + color = ; + linux,default-trigger = "phy0radio"; + }; + + led_usb1_white { + label = "white:usb1"; + gpios = <&led_gpio 3 GPIO_ACTIVE_LOW>; + color = ; + }; + + led_usb2_white { + label = "white:usb2"; + gpios = <&led_gpio 4 GPIO_ACTIVE_LOW>; + color = ; + }; + + led_wan_white: wan-white { + label = "white:wan"; + gpios = <&led_gpio 5 GPIO_ACTIVE_LOW>; + color = ; + }; + + led_aqr_green { + label = "green:aqr"; + gpios = <&led_gpio 6 GPIO_ACTIVE_LOW>; + color = ; + }; + + led_aqr_red { + label = "red:aqr"; + gpios = <&led_gpio 10 GPIO_ACTIVE_LOW>; + color = ; + }; + + led_aqr_white { + label = "white:aqr"; + gpios = <&led_gpio 11 GPIO_ACTIVE_LOW>; + color = ; + }; + + led_wps_white { + label = "white:wps"; + gpios = <&tlmm 40 GPIO_ACTIVE_HIGH>; + color = ; + }; + }; +}; + +&tlmm { + mdio_pins: mdio-pins { + mdc { + pins = "gpio68"; + function = "mdc"; + drive-strength = <8>; + bias-pull-up; + }; + + mdio { + pins = "gpio69"; + function = "mdio"; + drive-strength = <8>; + bias-pull-up; + }; + }; +}; + +&mdio { + status = "okay"; + + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + reset-gpios = <&tlmm 37 GPIO_ACTIVE_LOW>; + + qca8075_0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + }; + + qca8075_1: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; + + qca8075_2: ethernet-phy@2 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <2>; + }; + + qca8075_3: ethernet-phy@3 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <3>; + }; + + qca8075_4: ethernet-phy@4 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <4>; + }; + + aqr111b0: ethernet-phy@7 { + compatible ="ethernet-phy-ieee802.3-c45"; + reg = <7>; + reset-gpios = <&tlmm 59 GPIO_ACTIVE_LOW>; + }; +}; + +&switch { + status = "okay"; + + switch_lan_bmp = <0x3e>; /* lan port bitmap */ + switch_wan_bmp = <0x40>; /* wan port bitmap */ + switch_mac_mode = <0x0>; /* mac mode for uniphy instance0*/ + switch_mac_mode1 = <0xff>; /* mac mode for uniphy instance1*/ + switch_mac_mode2 = <0xd>; /* mac mode for uniphy instance2*/ + bm_tick_mode = <0>; /* bm tick mode */ + tm_tick_mode = <0>; /* tm tick mode */ + + qcom,port_phyinfo { + port@1 { + port_id = <1>; + phy_address = <0>; + }; + port@2 { + port_id = <2>; + phy_address = <1>; + }; + port@3 { + port_id = <3>; + phy_address = <2>; + }; + port@4 { + port_id = <4>; + phy_address = <3>; + }; + port@5 { + port_id = <5>; + phy_address = <4>; + }; + port@6 { + port_id = <6>; + phy_address = <7>; + compatible = "ethernet-phy-ieee802.3-c45"; + ethernet-phy-ieee802.3-c45; + }; + }; +}; + +&edma { + status = "okay"; +}; + +&dp1 { + status = "okay"; + phy-handle = <&qca8075_0>; + label = "lan4"; + nvmem-cells = <&macaddr_dp1>; + nvmem-cell-names = "mac-address"; +}; + +&dp2 { + status = "okay"; + phy-handle = <&qca8075_1>; + label = "lan3"; + nvmem-cells = <&macaddr_dp2>; + nvmem-cell-names = "mac-address"; +}; + +&dp3 { + status = "okay"; + phy-handle = <&qca8075_2>; + label = "lan2"; + nvmem-cells = <&macaddr_dp3>; + nvmem-cell-names = "mac-address"; +}; + +&dp4 { + status = "okay"; + phy-handle = <&qca8075_3>; + label = "lan1"; + nvmem-cells = <&macaddr_dp4>; + nvmem-cell-names = "mac-address"; +}; + +&dp5 { + status = "okay"; + phy-handle = <&qca8075_4>; + label = "wan"; + nvmem-cells = <&macaddr_dp5>; + nvmem-cell-names = "mac-address"; +}; + +&dp6_syn { + status = "okay"; + phy-handle = <&aqr111b0>; + label = "lan5"; + nvmem-cells = <&macaddr_dp6_syn>; + nvmem-cell-names = "mac-address"; +}; + +&blsp1_uart5 { + status = "okay"; +}; + +&blsp1_i2c2 { + status = "okay"; + + g761@3e { + compatible = "gmt,g763"; + reg = <0x3e>; + clocks =<&sleep_clk>; + fan_gear_mode = <0>; + fan_start = <1>; + pwm_polarity = <0>; + }; +}; + +&qpic_bam { + status = "okay"; +}; + +&qpic_nand { + status = "okay"; + + nand@0 { + reg = <0>; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + nand-bus-width = <8>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "0:sbl1"; + reg = <0x00 0x100000>; + read-only; + }; + + partition@100000 { + label = "0:mibib"; + reg = <0x100000 0x100000>; + read-only; + }; + + partition@200000 { + label = "0:bootconfig"; + reg = <0x200000 0x80000>; + read-only; + }; + + partition@280000 { + label = "0:bootconfig_1"; + reg = <0x280000 0x80000>; + read-only; + }; + + partition@300000 { + label = "0:qsee"; + reg = <0x300000 0x300000>; + read-only; + }; + + partition@600000 { + label = "0:qsee_1"; + reg = <0x600000 0x300000>; + read-only; + }; + + partition@900000 { + label = "0:devcfg"; + reg = <0x900000 0x80000>; + read-only; + }; + + partition@980000 { + label = "0:devcfg_1"; + reg = <0x980000 0x80000>; + read-only; + }; + + partition@a00000 { + label = "0:apdp"; + reg = <0xa00000 0x80000>; + read-only; + }; + + partition@a80000 { + label = "0:apdp_1"; + reg = <0xa80000 0x80000>; + read-only; + }; + + partition@b00000 { + label = "0:rpm"; + reg = <0xb00000 0x80000>; + read-only; + }; + + partition@b80000 { + label = "0:rpm_1"; + reg = <0xb80000 0x80000>; + read-only; + }; + + partition@c00000 { + label = "0:cdt"; + reg = <0xc00000 0x80000>; + read-only; + }; + + partition@c80000 { + label = "0:cdt_1"; + reg = <0xc80000 0x80000>; + read-only; + }; + + partition@d00000 { + label = "0:appsblenv"; + reg = <0xd00000 0x80000>; + }; + + partition@d80000 { + label = "0:appsbl"; + reg = <0xd80000 0x100000>; + read-only; + }; + + partition@e80000 { + label = "0:appsbl_1"; + reg = <0xe80000 0x100000>; + read-only; + }; + + partition@f80000 { + label = "0:art"; + reg = <0xf80000 0x80000>; + read-only; + }; + + partition@1000000 { + label = "0:art.bak"; + reg = <0x1000000 0x0080000>; + read-only; + }; + + partition@1080000 { + label = "config"; + reg = <0x1080000 0x0100000>; + read-only; + }; + + partition@1180000 { + label = "boarddata1"; + reg = <0x1180000 0x0100000>; + read-only; + + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_dp1: macaddr@0 { + reg = <0x0 0x6>; + }; + + macaddr_dp2: macaddr@1 { + reg = <0x6 0x6>; + }; + + macaddr_dp3: macaddr@2 { + reg = <0xc 0x6>; + }; + + macaddr_dp4: macaddr@3 { + reg = <0x12 0x6>; + }; + + macaddr_dp5: macaddr@4 { + reg = <0x18 0x6>; + }; + + macaddr_dp6_syn: macaddr@5 { + reg = <0x1e 0x6>; + }; + + }; + + partition@1280000 { + label = "boarddata2"; + reg = <0x1280000 0x0100000>; + read-only; + }; + + partition@1380000 { + label = "pot"; + reg = <0x1380000 0x0100000>; + read-only; + }; + + partition@1480000 { + label = "dnidata"; + reg = <0x1480000 0x0500000>; + read-only; + }; + + partition@1980000 { + label = "kernel"; + reg = <0x1980000 0x1d00000>; + }; + + partition@7e00000 { + label = "ethphyfw"; + reg = <0x7e00000 0x80000>; + }; + + partition@e8800000 { + label = "rootfs"; + reg = <0xe880000 0x11780000>; + }; + }; + }; +}; + +&qusb_phy_0 { + status = "okay"; +}; + +&qusb_phy_1 { + status = "okay"; +}; + +&ssphy_0 { + status = "okay"; +}; + +&ssphy_1 { + status = "okay"; +}; + +&usb_0 { + status = "okay"; +}; + +&usb_1 { + status = "okay"; +}; + +&wifi{ + status = "okay"; + + qcom,ath11k-calibration-variant = "Netgear-RAX120v2"; +}; + +&cryptobam { + status = "okay"; +}; + +&crypto { + status = "okay"; +}; + +&prng { + status = "okay"; +}; diff --git a/target/linux/qualcommax/image/ipq807x.mk b/target/linux/qualcommax/image/ipq807x.mk index 555c723c5f..440a267497 100644 --- a/target/linux/qualcommax/image/ipq807x.mk +++ b/target/linux/qualcommax/image/ipq807x.mk @@ -91,6 +91,30 @@ define Device/edimax_cax1800 endef TARGET_DEVICES += edimax_cax1800 +define Device/netgear_rax120v2 + $(call Device/FitImage) + $(call Device/UbiFit) + DEVICE_VENDOR := Netgear + DEVICE_MODEL := RAX120v2 + BLOCKSIZE := 128k + PAGESIZE := 2048 + DEVICE_DTS_CONFIG := config@hk01 + SOC := ipq8074 + KERNEL_SIZE := 29696k + NETGEAR_BOARD_ID := RAX120 + NETGEAR_HW_ID := 29765589+0+512+1024+4x4+8x8 + DEVICE_PACKAGES := ipq-wifi-netgear_rax120v2 kmod-spi-gpio \ + kmod-spi-bitbang kmod-gpio-nxp-74hc164 kmod-hwmon-g761 + IMAGES = web-ui-factory.img sysupgrade.bin + IMAGE/web-ui-factory.img := append-image initramfs-uImage.itb | \ + pad-offset $$$$(BLOCKSIZE) 64 | append-uImage-fakehdr filesystem | \ + netgear-dni + IMAGE/sysupgrade.bin := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | \ + append-uImage-fakehdr filesystem | sysupgrade-tar kernel=$$$$@ | \ + append-metadata +endef +TARGET_DEVICES += netgear_rax120v2 + define Device/netgear_wax218 $(call Device/FitImage) $(call Device/UbiFit) diff --git a/target/linux/qualcommax/ipq807x/base-files/etc/board.d/01_leds b/target/linux/qualcommax/ipq807x/base-files/etc/board.d/01_leds index a89b4c1564..6e2ec60403 100644 --- a/target/linux/qualcommax/ipq807x/base-files/etc/board.d/01_leds +++ b/target/linux/qualcommax/ipq807x/base-files/etc/board.d/01_leds @@ -9,6 +9,9 @@ case "$board" in edgecore,eap102) ucidef_set_led_netdev "wan" "WAN" "green:wanpoe" "wan" ;; +netgear,rax120v2) + ucidef_set_led_netdev "aqr" "AQR" "white:aqr" "lan5" + ;; netgear,wax218) ucidef_set_led_netdev "lan" "LAN" "blue:lan" "lan" ucidef_set_led_wlan "wlan5g" "WIFI 5GHz" "blue:wlan5g" "phy0radio" diff --git a/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network b/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network index 8175a99f97..3953ae8db2 100644 --- a/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network +++ b/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network @@ -22,6 +22,9 @@ ipq807x_setup_interfaces() edimax,cax1800) ucidef_set_interfaces_lan_wan "lan" ;; + netgear,rax120v2) + ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 lan5" "wan" + ;; netgear,wax218) ucidef_set_interface_lan "lan" "dhcp" ;; diff --git a/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata b/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata index f9315573ec..742730f476 100644 --- a/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata +++ b/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata @@ -14,6 +14,7 @@ case "$FIRMWARE" in edgecore,eap102|\ edimax,cax1800|\ dynalink,dl-wrx36|\ + netgear,rax120v2|\ netgear,wax218|\ qnap,301w|\ redmi,ax6|\ diff --git a/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh b/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh index 458eb16b79..a7af1cc1df 100644 --- a/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh +++ b/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh @@ -68,6 +68,7 @@ platform_do_upgrade() { ;; compex,wpq873|\ edimax,cax1800|\ + netgear,rax120v2|\ netgear,wax218) nand_do_upgrade "$1" ;;