From: Chuanhong Guo Date: Sun, 4 Aug 2019 14:13:45 +0000 (+0800) Subject: ath79: add support for PISEN WMB001N X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=4d5dae27419a6883484d0a051c653888d2042bca;p=openwrt%2Fstaging%2Fdangole.git ath79: add support for PISEN WMB001N Specifications: - SoC: AR9341 - RAM: 64M - Flash: 16M - Ethernet: 1 * FE port - WiFi: ar934x-wmac - Sound: WM8918 DAC 1 * 3.5mm headphone jack 2 * RCA connectors for speakers 1 * SPDIF out - USB: 1 * USB2.0 port Flash instruction: Upload generated factory image via vendor's web interface. Notes: A. Audio stuff: 1. Since AR934x, all pins for peripheral blocks can be mapped to any available GPIOs. We currently don't have a PCM/I2S driver for AR934x so pinmux for i2s and SPDIF are bound to i2c gpio node. This should be moved into I2S node when a PCM/I2S driver is available. 2. The i2c-gpio node is for WM8918. DT binding for it can't be added currently due to a missing clock from I2S PLL. B. Factory image: Image contains a image header and a tar.gz archive. 1. Header: A 288 byte header that has nothing to do with appended tarball. Format: 0x0-0x7 and 0x18-0x1F: magic values 0x20: Model number string 0xFC: Action string. It's either "update" or "backup" 0x11C: A 1 byte checksum. It's XOR result of 0x8-0x11B Firmware doesn't care about the rest of the header as long as checksum result is correct. The same header is used for backup and update routines so the magic values and model number can be obtained by generating a backup bin and grab values from it. 2. Tarball: It contains two files named uImage and rootfs, which will be flashed into corresponding mtd partition. Writing a special utility that can only output a fixed binary blob is overkill so factory image header is placed under image/bin instead. C. LED The wifi led has "Wi-Fi" marked on the case but vendor's firmware used it as system status indicator. I did the same in this device support patch. D. Firmware Factory u-boot is built without 'savenv' support so it's impossible to change kernel offset. A 2MB kernel partition won't be enough in the future. OKLI loader is used here to migrate this problem: 1. add OKLI image magic support into uImage parser. 2. build an OKLI loader, compress it with lzma and add a normal uImage header. 3. flash the loader to where the original kernel supposed to be. 4. create a uImage firmware using OKLI loader. 5. flash the created firmware to where rootfs supposed to be. By doing so, u-boot will start OKLI loader, which will then load the actual kernel at 0x20000. The kernel partition is 2MB, which is too much for our loader. To save this space, "mtd-concat" is used here: 1. create a 64K (1 erase block) partition for OKLI loader and create another partition with the left space. 2. concatenate rootfs and this partition into a virtual flash. 3. use the virtual flash for firmware partition. Currently OKLI loader is flashed with factory image only. sysupgrade won't replace it. Since it only has one function and it works for several years, its unlikely to have some bugs that requires a replacement. Signed-off-by: Chuanhong Guo --- diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network index e3c1f423f1..3b89c9c58d 100755 --- a/target/linux/ath79/base-files/etc/board.d/02_network +++ b/target/linux/ath79/base-files/etc/board.d/02_network @@ -25,6 +25,7 @@ ath79_setup_interfaces() ocedo,koala|\ ocedo,raccoon|\ pcs,cap324|\ + pisen,wmb001n|\ pisen,wmm003n|\ pqi,air-pen|\ tplink,cpe210-v2|\ diff --git a/target/linux/ath79/dts/ar9341_pisen_wmb001n.dts b/target/linux/ath79/dts/ar9341_pisen_wmb001n.dts new file mode 100644 index 0000000000..8029de5495 --- /dev/null +++ b/target/linux/ath79/dts/ar9341_pisen_wmb001n.dts @@ -0,0 +1,225 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include +#include + +#include "ar9341.dtsi" + +/ { + model = "PISEN WMB001N"; + compatible = "pisen,wmb001n", "qca,ar9341"; + + aliases { + serial0 = &uart; + led-boot = &wifi; + led-failsafe = &wifi; + led-running = &wifi; + led-upgrade = &wifi; + }; + + i2c { + compatible = "i2c-gpio"; + pinctrl-names = "default"; + pinctrl-0 = <&pmx_i2c_gpio &pmx_i2s_spdif>; + + sda-gpios = <&gpio 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio 20 GPIO_ACTIVE_HIGH>; + /* + * Pull-up resistor for scl is missing on this board. + * Following settings trick i2c-gpio to use output mode + * instead of open-drain for scl. + */ + i2c-gpio,scl-output-only; + i2c-gpio,scl-open-drain; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + linux,code = ; + gpios = <&gpio 17 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + + vol_down { + label = "volume down"; + linux,code = ; + gpios = <&gpio 18 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + + vol_up { + label = "volume up"; + linux,code = ; + gpios = <&gpio 19 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&jtag_disable_pins>; + + volume1 { + label = "wmb001n:blue:volume1"; + gpios = <&gpio 0 GPIO_ACTIVE_HIGH>; + }; + + volume2 { + label = "wmb001n:blue:volume2"; + gpios = <&gpio 1 GPIO_ACTIVE_HIGH>; + }; + + volume3 { + label = "wmb001n:blue:volume3"; + gpios = <&gpio 2 GPIO_ACTIVE_HIGH>; + }; + + volume4 { + label = "wmb001n:blue:volume4"; + gpios = <&gpio 3 GPIO_ACTIVE_HIGH>; + }; + + volume5 { + label = "wmb001n:blue:volume5"; + gpios = <&gpio 4 GPIO_ACTIVE_HIGH>; + }; + + wifi: wifi { + label = "wmb001n:blue:wifi"; + gpios = <&gpio 22 GPIO_ACTIVE_HIGH>; + }; + }; + + virtual_flash { + compatible = "mtd-concat"; + devices = <&fwpart1 &fwpart2>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + reg = <0x0 0x0>; + label = "firmware"; + compatible = "openwrt,okli"; + }; + }; + }; +}; + +&pinmux { + pmx_i2c_gpio: pinmux_i2c_gpio { + pinctrl-single,bits = <0x10 0x0 0xff>, + <0x14 0x0 0xff>; + }; + + pmx_i2s_spdif: pinmux_i2s_spdif { + pinctrl-single,bits = <0x8 0x0e000000 0xff000000>, + <0xc 0x0f0c0d 0xffffff>, + <0x14 0x1900 0xff00>; + }; +}; + +&ref { + clock-frequency = <25000000>; +}; + +&uart { + status = "okay"; +}; + +&gpio { + status = "okay"; +}; + +&spi { + num-cs = <1>; + + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + uboot: partition@0 { + label = "u-boot"; + reg = <0x0 0x10000>; + read-only; + }; + + partition@10000 { + label = "u-boot-env"; + reg = <0x10000 0x10000>; + read-only; + }; + + fwpart1: partition@20000 { + label = "fwpart1"; + reg = <0x20000 0xdc0000>; + }; + + partition@de0000 { + label = "loader"; + reg = <0xde0000 0x10000>; + }; + + fwpart2: partition@df0000 { + label = "fwpart2"; + reg = <0xdf0000 0x1f0000>; + }; + + partition@fe0000 { + label = "mib0"; + reg = <0xfe0000 0x10000>; + read-only; + }; + + art: partition@ff0000 { + label = "art"; + reg = <0xff0000 0x10000>; + read-only; + }; + }; + }; +}; + +ð0 { + status = "okay"; + phy-handle = <&swphy4>; + mtd-mac-address = <&art 0x0>; +}; + +ð1 { + compatible = "syscon", "simple-mfd"; + status = "okay"; + + gmac-config { + device = <&gmac>; + switch-phy-swap = <0>; + }; +}; + +&usb { + status = "okay"; +}; + +&usb_phy { + status = "okay"; +}; + +&wmac { + status = "okay"; + mtd-cal-data = <&art 0x1000>; +}; diff --git a/target/linux/ath79/image/Makefile b/target/linux/ath79/image/Makefile index 734f27e689..24768ef5e0 100644 --- a/target/linux/ath79/image/Makefile +++ b/target/linux/ath79/image/Makefile @@ -36,6 +36,10 @@ define Build/loader-okli mv "$@.new" "$@" endef +define Build/append-loader-okli + cat "$(KDIR)/loader-$(word 1,$(1)).$(LOADER_TYPE)" >> "$@" +endef + define Build/relocate-kernel rm -rf $@.relocate $(CP) ../../generic/image/relocate $@.relocate diff --git a/target/linux/ath79/image/bin/pisen_wmb001n_factory-header.bin b/target/linux/ath79/image/bin/pisen_wmb001n_factory-header.bin new file mode 100644 index 0000000000..99e1e8a2db Binary files /dev/null and b/target/linux/ath79/image/bin/pisen_wmb001n_factory-header.bin differ diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index abaf1a3e07..5127cfd510 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -58,6 +58,18 @@ define Build/nec-fw mv $@.new $@ endef +define Build/pisen_wmb001n-factory + -[ -f "$@" ] && \ + mkdir -p "$@.tmp" && \ + cp "$(KDIR)/loader-$(word 1,$(1)).uImage" "$@.tmp/uImage" && \ + mv "$@" "$@.tmp/rootfs" && \ + cp "bin/pisen_wmb001n_factory-header.bin" "$@" && \ + $(TAR) -cp --numeric-owner --owner=0 --group=0 --mode=a-s --sort=name \ + $(if $(SOURCE_DATE_EPOCH),--mtime="@$(SOURCE_DATE_EPOCH)") \ + -C "$@.tmp" . | gzip -9n >> "$@" && \ + rm -rf "$@.tmp" +endef + define Device/seama KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma KERNEL_INITRAMFS := $$(KERNEL) | seama @@ -775,6 +787,23 @@ define Device/netgear_wndr3700v2 endef TARGET_DEVICES += netgear_wndr3700v2 +define Device/pisen_wmb001n + ATH_SOC := ar9341 + DEVICE_VENDOR := PISEN + DEVICE_MODEL := WMB001N + IMAGE_SIZE := 14080k + DEVICE_PACKAGES := kmod-i2c-core kmod-i2c-gpio kmod-usb2 + LOADER_TYPE := bin + LOADER_FLASH_OFFS := 0x20000 + COMPILE := loader-$(1).bin loader-$(1).uImage + COMPILE/loader-$(1).bin := loader-okli-compile + COMPILE/loader-$(1).uImage := append-loader-okli $(1) | pad-to 64k | lzma | uImage lzma + KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49 + IMAGES += factory.bin + IMAGE/factory.bin := $$(IMAGE/sysupgrade.bin) | pisen_wmb001n-factory $(1) +endef +TARGET_DEVICES += pisen_wmb001n + define Device/pisen_wmm003n $(Device/tplink-8mlzma) ATH_SOC := ar9331