From: Prabhakar Kushwaha Date: Mon, 27 Jan 2014 09:11:55 +0000 (+0530) Subject: powerpc/t104xrdb: Update T1042RDB.h in config folder X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=48aee3913d1e99b9f0b91ff0eb52700b4dd24d25;p=project%2Fbcm63xx%2Fu-boot.git powerpc/t104xrdb: Update T1042RDB.h in config folder Add usb2 node entry to hwconfig default Remove DDR controller interleaving from hwconfig Move SPI related macros out of "#ifdef CONFIG_SPIFLASH" Add CONFIG_SYS_CSPR2_EXT to make CPLD accessible in u-boot Signed-off-by: Prabhakar Kushwaha [York Sun: Fix commit message] Signed-off-by: York Sun --- diff --git a/include/configs/T1042RDB_PI.h b/include/configs/T1042RDB_PI.h index aafa8139b1..1cbc375b04 100644 --- a/include/configs/T1042RDB_PI.h +++ b/include/configs/T1042RDB_PI.h @@ -79,10 +79,6 @@ #if defined(CONFIG_SPIFLASH) #define CONFIG_SYS_EXTRA_ENV_RELOC #define CONFIG_ENV_IS_IN_SPI_FLASH -#define CONFIG_ENV_SPI_BUS 0 -#define CONFIG_ENV_SPI_CS 0 -#define CONFIG_ENV_SPI_MAX_HZ 10000000 -#define CONFIG_ENV_SPI_MODE 0 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ #define CONFIG_ENV_SECT_SIZE 0x10000 @@ -202,6 +198,7 @@ /* CPLD on IFC */ #define CONFIG_SYS_CPLD_BASE 0xffdf0000 #define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull | CONFIG_SYS_CPLD_BASE) +#define CONFIG_SYS_CSPR2_EXT (0xf) #define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE_PHYS) \ | CSPR_PORT_SIZE_8 \ | CSPR_MSEL_GPCM \ @@ -394,6 +391,10 @@ #define CONFIG_CMD_SF #define CONFIG_SF_DEFAULT_SPEED 10000000 #define CONFIG_SF_DEFAULT_MODE 0 +#define CONFIG_ENV_SPI_BUS 0 +#define CONFIG_ENV_SPI_CS 0 +#define CONFIG_ENV_SPI_MAX_HZ 10000000 +#define CONFIG_ENV_SPI_MODE 0 /* * General PCI @@ -631,9 +632,9 @@ #define __USB_PHY_TYPE utmi #define CONFIG_EXTRA_ENV_SETTINGS \ - "hwconfig=fsl_ddr:ctlr_intlv=cacheline," \ - "bank_intlv=cs0_cs1;" \ - "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ + "hwconfig=fsl_ddr:bank_intlv=cs0_cs1;" \ + "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) ";"\ + "usb2:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ "netdev=eth0\0" \ "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \