From: Marek Lindner Date: Fri, 14 Dec 2018 15:46:53 +0000 (+0800) Subject: ipq40xx: add support for Plasma Cloud PA2200 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=4871fd2616acb03fefe69b068955dba36eb00770;p=openwrt%2Fstaging%2Fthess.git ipq40xx: add support for Plasma Cloud PA2200 Device specifications: * QCA IPQ4019 * 256 MB of RAM * 32 MB of SPI NOR flash (w25q256) - 2x 15 MB available; but one of the 15 MB regions is the recovery image * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=PlasmaCloud-PA2200 * 2T2R 5 GHz (channel 36-64) - QCA9888 hw2.0 (PCI) - requires special BDF in QCA9888/hw2.0/board-2.bin bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA2200 * 2T2R 5 GHz (channel 100-165) - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=PlasmaCloud-PA2200 * GPIO-LEDs for 2.4GHz, 5GHz-SoC and 5GHz-PCIE * GPIO-LEDs for power (orange) and status (blue) * 1x GPIO-button (reset) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x gigabit ethernet - phy@mdio3: + Label: Ethernet 1 + gmac0 (ethaddr) in original firmware + used as LAN interface - phy@mdio4: + Label: Ethernet 2 + gmac1 (eth1addr) in original firmware + 802.3at POE+ + used as WAN interface * 12V 2A DC Flashing instructions: The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. Signed-off-by: Marek Lindner [sven@narfation.org: prepare commit message, rebase, use all LEDs, switch to dualboot_datachk upgrade script, use eth1 as designated WAN interface] Signed-off-by: Sven Eckelmann --- diff --git a/package/boot/uboot-envtools/files/ipq40xx b/package/boot/uboot-envtools/files/ipq40xx index 9252c0ffac..bcb4c5c962 100644 --- a/package/boot/uboot-envtools/files/ipq40xx +++ b/package/boot/uboot-envtools/files/ipq40xx @@ -37,7 +37,8 @@ glinet,gl-b1300 |\ luma,wrtq-329acn |\ openmesh,a42 |\ openmesh,a62 |\ -plasmacloud,pa1200) +plasmacloud,pa1200 |\ +plasmacloud,pa2200) ubootenv_add_uci_config "/dev/mtd5" "0x0" "0x10000" "0x10000" ;; buffalo,wtr-m2133hp) diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile index e26269a710..dfb9e0feb3 100644 --- a/package/firmware/ipq-wifi/Makefile +++ b/package/firmware/ipq-wifi/Makefile @@ -43,6 +43,7 @@ ALLWIFIBOARDS:= \ luma_wrtq-329acn \ mobipromo_cm520-79f \ plasmacloud_pa1200 \ + plasmacloud_pa2200 \ qxwlan_e2600ac ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD)) @@ -122,6 +123,7 @@ $(eval $(call generate-ipq-wifi-package,linksys_mr8300-v0,Linksys MR8300)) $(eval $(call generate-ipq-wifi-package,luma_wrtq-329acn,Luma WRTQ-329ACN)) $(eval $(call generate-ipq-wifi-package,mobipromo_cm520-79f,MobiPromo CM520-79F)) $(eval $(call generate-ipq-wifi-package,plasmacloud_pa1200,Plasma Cloud PA1200)) +$(eval $(call generate-ipq-wifi-package,plasmacloud_pa2200,Plasma Cloud PA2200)) $(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac,Qxwlan E2600AC)) $(foreach PACKAGE,$(ALLWIFIPACKAGES),$(eval $(call BuildPackage,$(PACKAGE)))) diff --git a/package/firmware/ipq-wifi/board-plasmacloud_pa2200.ipq4019 b/package/firmware/ipq-wifi/board-plasmacloud_pa2200.ipq4019 new file mode 100644 index 0000000000..d1db0f5f4b Binary files /dev/null and b/package/firmware/ipq-wifi/board-plasmacloud_pa2200.ipq4019 differ diff --git a/package/firmware/ipq-wifi/board-plasmacloud_pa2200.qca9888 b/package/firmware/ipq-wifi/board-plasmacloud_pa2200.qca9888 new file mode 100644 index 0000000000..6c3f083eb2 Binary files /dev/null and b/package/firmware/ipq-wifi/board-plasmacloud_pa2200.qca9888 differ diff --git a/scripts/om-fwupgradecfg-gen.sh b/scripts/om-fwupgradecfg-gen.sh index c5dcfb0018..bf7c047c5b 100755 --- a/scripts/om-fwupgradecfg-gen.sh +++ b/scripts/om-fwupgradecfg-gen.sh @@ -7,7 +7,7 @@ # usage() { - echo "Usage: $0 " + echo "Usage: $0 " rm -f $CFG_OUT exit 1 } @@ -39,7 +39,7 @@ case $CE_TYPE in SIZE_FACTOR=1024 SIZE_FORMAT="0x%08x" ;; - A62) + A62|PA2200) MAX_PART_SIZE=15552 KERNEL_FLASH_ADDR=0x1a0000 SIZE_FACTOR=1024 diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index b9e79c3b68..4361b7c395 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -18,7 +18,8 @@ ipq40xx_setup_interfaces() engenius,emr3500|\ engenius,ens620ext|\ luma,wrtq-329acn|\ - plasmacloud,pa1200) + plasmacloud,pa1200|\ + plasmacloud,pa2200) ucidef_set_interfaces_lan_wan "eth0" "eth1" ;; aruba,ap-303|\ diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index ade0d74341..e50732586a 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -36,7 +36,8 @@ case "$FIRMWARE" in ath10k_patch_mac $(mtd_get_mac_binary ORGDATA 0x32) ;; engenius,eap2200 |\ - openmesh,a62) + openmesh,a62 |\ + plasmacloud,pa2200) caldata_extract "0:ART" 0x9000 0x2f20 ;; linksys,ea8300 |\ @@ -102,6 +103,7 @@ case "$FIRMWARE" in openmesh,a42 |\ openmesh,a62 |\ plasmacloud,pa1200 |\ + plasmacloud,pa2200 |\ qxwlan,e2600ac-c1 |\ qxwlan,e2600ac-c2 |\ unielec,u4019-32m) @@ -200,6 +202,7 @@ case "$FIRMWARE" in openmesh,a42 |\ openmesh,a62 |\ plasmacloud,pa1200 |\ + plasmacloud,pa2200 |\ qxwlan,e2600ac-c1 |\ qxwlan,e2600ac-c2 |\ unielec,u4019-32m) diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/dualboot_datachk.sh b/target/linux/ipq40xx/base-files/lib/upgrade/dualboot_datachk.sh index 60886071c9..81418fe0ba 100644 --- a/target/linux/ipq40xx/base-files/lib/upgrade/dualboot_datachk.sh +++ b/target/linux/ipq40xx/base-files/lib/upgrade/dualboot_datachk.sh @@ -48,6 +48,7 @@ platform_do_upgrade_dualboot_datachk() { openmesh,a42) primary_kernel_mtd=8 ;; + plasmacloud,pa2200|\ openmesh,a62) primary_kernel_mtd=10 ;; diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh index 22e9ffe114..e43225cbb2 100644 --- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh @@ -112,7 +112,8 @@ platform_do_upgrade() { ;; openmesh,a42 |\ openmesh,a62 |\ - plasmacloud,pa1200) + plasmacloud,pa1200 |\ + plasmacloud,pa2200) PART_NAME="inactive" platform_do_upgrade_dualboot_datachk "$1" ;; diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-pa2200.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-pa2200.dts new file mode 100644 index 0000000000..2d0655114b --- /dev/null +++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-pa2200.dts @@ -0,0 +1,210 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* Copyright (c) 2017-2020, Sven Eckelmann + * Copyright (c) 2018, Marek Lindner + */ + +#include "qcom-ipq4019.dtsi" +#include +#include +#include + +/ { + model = "Plasma Cloud PA2200"; + compatible = "plasmacloud,pa2200"; + + soc { + rng@22000 { + status = "okay"; + }; + + mdio@90000 { + status = "okay"; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = ; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = ; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = ; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + watchdog@b017000 { + status = "okay"; + }; + + ess-switch@c000000 { + switch_lan_bmp = <0x10>; + switch_wan_bmp = <0x20>; + + status = "okay"; + }; + + edma@c080000 { + status = "okay"; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&tlmm 18 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + aliases { + led-boot = &led_power_orange; + led-failsafe = &led_status_blue; + led-running = &led_power_orange; + led-upgrade = &led_status_blue; + }; + + leds { + compatible = "gpio-leds"; + + led_power_orange: power_orange { + label = "orange:power"; + gpios = <&tlmm 43 GPIO_ACTIVE_LOW>; + }; + + 2g_blue { + label = "blue:2g"; + gpios = <&tlmm 46 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + + 2g_green { + label = "green:5g1"; + gpios = <&tlmm 47 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + 5g2_green { + label = "green:5g2"; + gpios = <&tlmm 48 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy2tpt"; + }; + + led_status_blue: status_blue { + label = "blue:status"; + gpios = <&tlmm 50 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&tlmm { + serial_pins: serial_pinmux { + mux { + pins = "gpio16", "gpio17"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + spi_0_pins: spi_0_pinmux { + pin { + function = "blsp_spi0"; + pins = "gpio13", "gpio14", "gpio15"; + drive-strength = <12>; + bias-disable; + }; + pin_cs { + function = "gpio"; + pins = "gpio12"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; +}; + +&blsp_dma { + status = "okay"; +}; + +&blsp1_spi1 { + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + status = "okay"; + cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>; + + flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <24000000>; + /* partitions are passed via bootloader */ + }; +}; + +&blsp1_uart1 { + pinctrl-0 = <&serial_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&cryptobam { + status = "okay"; +}; + +&gmac0 { + qcom,phy_mdio_addr = <3>; + qcom,poll_required = <1>; + qcom,forced_speed = <1000>; + qcom,forced_duplex = <1>; + vlan_tag = <1 0x10>; +}; + +&pcie0 { + status = "okay"; + perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>; + wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>; + + bridge@0,0 { + reg = <0x00000000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + ranges; + + wifi2: wifi@1,0 { + compatible = "qcom,ath10k"; + status = "okay"; + reg = <0x00010000 0 0 0 0>; + qcom,ath10k-calibration-variant = "PlasmaCloud-PA2200"; + ieee80211-freq-limit = <5170000 5350000>; + }; + }; +}; + +&wifi0 { + status = "okay"; + qcom,ath10k-calibration-variant = "PlasmaCloud-PA2200"; +}; + +&wifi1 { + status = "okay"; + qcom,ath10k-calibration-variant = "PlasmaCloud-PA2200"; + ieee80211-freq-limit = <5470000 5875000>; +}; diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile index b0fde22813..86bf5a2ccb 100644 --- a/target/linux/ipq40xx/image/Makefile +++ b/target/linux/ipq40xx/image/Makefile @@ -664,6 +664,22 @@ define Device/plasmacloud_pa1200 endef TARGET_DEVICES += plasmacloud_pa1200 +define Device/plasmacloud_pa2200 + $(call Device/FitImageLzma) + DEVICE_VENDOR := Plasma Cloud + DEVICE_MODEL := PA2200 + SOC := qcom-ipq4019 + DEVICE_DTS_CONFIG := config@pc.pa2200 + BLOCKSIZE := 64k + KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE) + IMAGE_SIZE := 15552k + IMAGES += factory.bin + IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=PA2200 + IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata + DEVICE_PACKAGES := ath10k-firmware-qca9888-ct ipq-wifi-plasmacloud-pa2200 uboot-envtools +endef +TARGET_DEVICES += plasmacloud_pa2200 + define Device/qcom_ap-dk01.1-c1 DEVICE_VENDOR := Qualcomm Atheros DEVICE_MODEL := AP-DK01.1 diff --git a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch index 8d725ebf9e..c4502aa3f7 100644 --- a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -837,11 +837,55 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -837,11 +837,56 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -52,6 +52,7 @@ Signed-off-by: John Crispin + qcom-ipq4019-e2600ac-c1.dtb \ + qcom-ipq4019-e2600ac-c2.dtb \ + qcom-ipq4019-habanero-dvk.dtb \ ++ qcom-ipq4019-pa2200.dtb \ + qcom-ipq4019-rtl30vw.dtb \ + qcom-ipq4019-u4019-32m.dtb \ + qcom-ipq4019-wpj419.dtb \