From: Mikhail Zhilkin Date: Sat, 9 Dec 2023 17:17:02 +0000 (+0000) Subject: mediatek: add support for Routerich AX3000 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=485adc9d3c436d31f9713a7d8d84adf266754e26;p=openwrt%2Fstaging%2Fdangole.git mediatek: add support for Routerich AX3000 This PR is continuation of work under "mediatek: add support for Routerich AX3000" #13703 by the agreement with PR #13703 original author (Maximilian Weinmann ). All reviews from the previous PR were taken into into account. Routerich AX3000 is a wireless WiFi 6 router. Specification ------------- - SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3 GHz - RAM : DDR3 256 MiB (ESMT M15T2G16128A) - Flash : SPI-NAND 128 MiB (ESMT F50L1G41LB) - WLAN : MediaTek MT7976CN dual-band WiFi 6 - 2.4 GHz : b/g/n/ax, MIMO 2x2 - 5 GHz : a/n/ac/ax, MIMO 2x2 - Ethernet : 10/100/1000 Mbps x4 (MediaTek MT7531AE) - USB : 1x 2.0 - UART : through-hole on PCB - [J500] GND, TX, RX, 3.3V (115200n8) - Buttons : Mesh, Reset - LEDs : 1x Power (Blue) 1x WiFi 2.4 GHz (Blue) 1x WiFi 5 GHz (Red) 1x Mesh (Blue) 3x LAN activity (Blue) 1x WAN activity (Blue) 2x WAN no-internet (Red) - Power : 12 VDC, 1.5 A Installation ------------ Flash OpenWrt 'sysupgrade.bin' image using stock firmware web-interface (without keeping settings). Return to stock --------------- Install stock firmware image (without keeping settings) using OpenWrt sysupgrade method. Recovery -------- Connect uart, use u-boot menu to flash stock firmware image or boot OpenWrt initramfs image. MAC addresses ------------- +---------+-------------------+-----------+ | | MAC | Algorithm | +---------+-------------------+-----------+ | WAN | 24:0f:5e:xx:xx:b4 | label | | LAN | 24:0f:5e:xx:xx:b5 | label+1 | | WLAN 2g | 24:0f:5e:xx:xx:b6 | label+2 | | WLAN 5g | 24:0f:5e:xx:xx:b7 | label+3 | +---------+-------------------+-----------+ The WLAN 2g MAC was found in 'Factory', 0x4 Co-authored-by: Maximilian Weinmann Signed-off-by: Mikhail Zhilkin --- diff --git a/package/boot/uboot-envtools/files/mediatek_filogic b/package/boot/uboot-envtools/files/mediatek_filogic index dd6726713b..8e8cb67a71 100644 --- a/package/boot/uboot-envtools/files/mediatek_filogic +++ b/package/boot/uboot-envtools/files/mediatek_filogic @@ -83,7 +83,8 @@ glinet,gl-mt6000) glinet,gl-mt3000) ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x80000" "0x20000" ;; -mercusys,mr90x-v1) +mercusys,mr90x-v1|\ +routerich,ax3000) local envdev=/dev/mtd$(find_mtd_index "u-boot-env") ubootenv_add_uci_config "$envdev" "0x0" "0x20000" "0x20000" "1" ;; diff --git a/target/linux/mediatek/dts/mt7981b-routerich-ax3000.dts b/target/linux/mediatek/dts/mt7981b-routerich-ax3000.dts new file mode 100644 index 0000000000..1dc4d380b8 --- /dev/null +++ b/target/linux/mediatek/dts/mt7981b-routerich-ax3000.dts @@ -0,0 +1,337 @@ +// SPDX-License-Identifier: GPL-2.0-only OR MIT + +/dts-v1/; +#include +#include +#include + +#include "mt7981.dtsi" + +/ { + model = "Routerich AX3000"; + compatible = "routerich,ax3000", "mediatek,mt7981"; + + aliases { + label-mac-device = &wan; + + led-boot = &led_power_blue; + led-failsafe = &led_power_blue; + led-running = &led_power_blue; + led-upgrade = &led_power_blue; + + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + gpio-keys { + compatible = "gpio-keys"; + + button-0 { + label = "mesh"; + linux,input-type = ; + linux,code = ; + gpios = <&pio 0 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + + button-1 { + label = "reset"; + gpios = <&pio 1 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <60>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led-0 { + color = ; + function = LED_FUNCTION_WLAN; + function-enumerator = <50>; + gpios = <&pio 5 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + + led-1 { + color = ; + function = LED_FUNCTION_WAN; + gpios = <&pio 6 GPIO_ACTIVE_HIGH>; + }; + + led_power_blue: led-2 { + color = ; + function = LED_FUNCTION_POWER; + gpios = <&pio 7 GPIO_ACTIVE_LOW>; + }; + + led-3 { + color = ; + function = LED_FUNCTION_LAN; + function-enumerator = <1>; + gpios = <&pio 9 GPIO_ACTIVE_LOW>; + }; + + led-4 { + color = ; + function = LED_FUNCTION_LAN; + function-enumerator = <2>; + gpios = <&pio 10 GPIO_ACTIVE_LOW>; + }; + + led-5 { + color = ; + function = LED_FUNCTION_LAN; + function-enumerator = <3>; + gpios = <&pio 11 GPIO_ACTIVE_LOW>; + }; + + led-6 { + color = ; + function = LED_FUNCTION_WAN; + gpios = <&pio 12 GPIO_ACTIVE_LOW>; + }; + + led-7 { + color = ; + function = LED_FUNCTION_WLAN; + function-enumerator = <24>; + gpios = <&pio 34 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + led-8 { + color = ; + /* LED_FUNCTION_MESH isn't implemented yet */ + function = "mesh"; + gpios = <&pio 35 GPIO_ACTIVE_LOW>; + }; + }; + + memory { + reg = <0 0x40000000 0 0x10000000>; + }; +}; + +ð { + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "2500base-x"; + + nvmem-cell-names = "mac-address"; + nvmem-cells = <&macaddr_factory_4 (-1)>; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; +}; + +&mdio_bus { + switch: switch@1f { + compatible = "mediatek,mt7531"; + reg = <0x1f>; + reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&pio>; + interrupts = <38 IRQ_TYPE_LEVEL_HIGH>; + }; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_flash_pins>; + status = "okay"; + + /* ESMT F50L1G41LB (128M) */ + spi_nand@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spi-nand"; + reg = <0>; + + spi-max-frequency = <52000000>; + spi-tx-buswidth = <4>; + spi-rx-buswidth = <4>; + + spi-cal-enable; + spi-cal-mode = "read-data"; + spi-cal-datalen = <7>; + spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4e 0x41 0x4e 0x44>; + spi-cal-addrlen = <5>; + spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>; + + mediatek,nmbm; + mediatek,bmt-max-ratio = <1>; + mediatek,bmt-max-reserved-blocks = <64>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0_all { + label = "spi0.0"; + reg = <0x0 0x8000000>; + read-only; + }; + + partition@0 { + label = "BL2"; + reg = <0x0 0x100000>; + read-only; + }; + + partition@100000 { + label = "u-boot-env"; + reg = <0x100000 0x80000>; + }; + + partition@180000 { + label = "Factory"; + reg = <0x180000 0x200000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + eeprom_factory_0: eeprom@0 { + reg = <0x0 0x1000>; + }; + + macaddr_factory_4: macaddr@4 { + compatible = "mac-base"; + reg = <0x4 0x6>; + #nvmem-cell-cells = <1>; + }; + }; + }; + + partition@380000 { + label = "FIP"; + reg = <0x380000 0x200000>; + read-only; + }; + + partition@580000 { + label = "ubi"; + reg = <0x580000 0x4000000>; + }; + + partition@4580000 { + label = "firmware_backup"; + reg = <0x4580000 0x2000000>; + read-only; + }; + + partition@6580000 { + label = "zrsave"; + reg = <0x6580000 0x100000>; + read-only; + }; + + partition@6680000 { + label = "config2"; + reg = <0x6680000 0x100000>; + read-only; + }; + }; + }; +}; + +&switch { + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan3"; + }; + + wan: port@4 { + reg = <4>; + label = "wan"; + + nvmem-cell-names = "mac-address"; + nvmem-cells = <&macaddr_factory_4 (-2)>; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; +}; + +&pio { + spi0_flash_pins: spi0-pins { + mux { + function = "spi"; + groups = "spi0", "spi0_wp_hold"; + }; + + conf-pu { + pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP"; + drive-strength = ; + bias-pull-up = ; + }; + + conf-pd { + pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO"; + drive-strength = ; + bias-pull-down = ; + }; + }; +}; + +&uart0 { + status = "okay"; +}; + +&usb_phy { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +&wifi { + status = "okay"; + nvmem-cell-names = "eeprom"; + nvmem-cells = <&eeprom_factory_0>; +}; + +&xhci { + status = "okay"; + mediatek,u3p-dis-msk = <0x1>; +}; diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds index f1fd58f1d0..360bdea9c8 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds @@ -26,6 +26,13 @@ netgear,wax220) ucidef_set_led_netdev "wlan2g" "WLAN2G" "blue:wlan2g" "phy0-ap0" ucidef_set_led_netdev "wlan5g" "WLAN5G" "blue:wlan5g" "phy1-ap0" ;; +routerich,ax3000) + ucidef_set_led_netdev "lan-1" "lan-1" "blue:lan-1" "lan1" "link tx rx" + ucidef_set_led_netdev "lan-2" "lan-2" "blue:lan-2" "lan2" "link tx rx" + ucidef_set_led_netdev "lan-3" "lan-3" "blue:lan-3" "lan3" "link tx rx" + ucidef_set_led_netdev "wan" "wan" "blue:wan" "wan" "link tx rx" + ucidef_set_led_netdev "wan-off" "wan-off" "red:wan" "wan" "link" + ;; xiaomi,mi-router-wr30u-112m-nmbm|\ xiaomi,mi-router-wr30u-stock|\ xiaomi,mi-router-wr30u-ubootmod) diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network index 4ffb7e53bf..adbd937acf 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network @@ -29,7 +29,8 @@ mediatek_setup_interfaces() confiabits,mt7981|\ cudy,wr3000-v1|\ jcg,q30-pro|\ - qihoo,360t7) + qihoo,360t7|\ + routerich,ax3000) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" wan ;; cmcc,rax3000m|\ diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac index bf7426fbee..ca98350a1b 100644 --- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac +++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac @@ -104,6 +104,7 @@ case "$board" in [ "$PHYNBR" = "0" ] && echo "$addr" > /sys${DEVPATH}/macaddress [ "$PHYNBR" = "1" ] && macaddr_add $addr 1 > /sys${DEVPATH}/macaddress ;; + routerich,ax3000|\ zbtlink,zbt-z8102ax|\ zbtlink,zbt-z8103ax|\ zyxel,ex5601-t0|\ diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk index afbdfefd6f..249810bcd8 100644 --- a/target/linux/mediatek/image/filogic.mk +++ b/target/linux/mediatek/image/filogic.mk @@ -653,6 +653,17 @@ define Device/qihoo_360t7 endef TARGET_DEVICES += qihoo_360t7 +define Device/routerich_ax3000 + DEVICE_VENDOR := Routerich + DEVICE_MODEL := AX3000 + DEVICE_DTS := mt7981b-routerich-ax3000 + DEVICE_DTS_DIR := ../dts + DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware kmod-usb3 + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata + SUPPORTED_DEVICES += mediatek,mt7981-spim-snand-rfb +endef +TARGET_DEVICES += routerich_ax3000 + define Device/tplink_tl-xdr-common DEVICE_VENDOR := TP-Link DEVICE_DTS_DIR := ../dts