From: Mohammad Sayful Islam Date: Wed, 3 Jan 2024 07:54:16 +0000 (+0000) Subject: ipq807x: add support for Linksys MX4200 V1 and V2 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=46a2490e8f24a1ad47e53b0b4ee875fa3658f2c1;p=openwrt%2Fopenwrt.git ipq807x: add support for Linksys MX4200 V1 and V2 Linksys MX4200 is a 802.11ax Tri-band router/AP. Specifications: * CPU: Qualcomm IPQ8174 Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 512Mb NAND * Ethernet: 4x1G RJ45 ports (QCA8075) * WLAN: * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 2x2@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LED-s: * RGB system led * Buttons: 1x Soft reset 1x WPS * Power: 12V DC Jack Installation instructions: Open Linksys Web UI - http://192.168.1.1/ca or http://10.65.1.1/ca depending on your setup. Login with your admin password. The default password can be found on a sticker under the device. To enter into the support mode, click on the “CA” link and the bottom of the page. Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button. Click start. Ignore all the prompts and warnings by click “yes” in all the popups. The Wifi radios are turned off by default. To configure the router, you will need to connect your computer to the LAN port of the device. Then you would need to write openwrt to the other partition for it to work - First Check booted partition fw_printenv -n boot_part - Then install Openwrt to the other partition if booted in slot 1: mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4200v(X)-squashfs-factory.bin alt_kernel - If in slot 2: mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4200v(X)-squashfs-factory.bin kernel Replace (X) with your model version either 1 or 2 Signed-off-by: Mohammad Sayful Islam Reviewed-by: Robert Marko --- diff --git a/package/boot/uboot-envtools/files/qualcommax_ipq807x b/package/boot/uboot-envtools/files/qualcommax_ipq807x index 761d5dfcc9..bcedfd9adc 100644 --- a/package/boot/uboot-envtools/files/qualcommax_ipq807x +++ b/package/boot/uboot-envtools/files/qualcommax_ipq807x @@ -29,6 +29,12 @@ edimax,cax1800) [ -n "$idx" ] && \ ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x10000" "0x20000" ;; +linksys,mx4200v1|\ +linksys,mx4200v2) + idx="$(find_mtd_index u_env)" + [ -n "$idx" ] && \ + ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x40000" "0x20000" "2" + ;; redmi,ax6|\ xiaomi,ax3600|\ xiaomi,ax9000) diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile index ef1a456403..189b8e9ec9 100644 --- a/package/firmware/ipq-wifi/Makefile +++ b/package/firmware/ipq-wifi/Makefile @@ -34,6 +34,7 @@ ALLWIFIBOARDS:= \ dynalink_dl-wrx36 \ edgecore_eap102 \ edimax_cax1800 \ + linksys_mx4200 \ netgear_rax120v2 \ netgear_wax218 \ netgear_wax620 \ @@ -83,7 +84,7 @@ define ipq-wifi-install-one $(call ipq-wifi-install-one-to,$(1),$(2),QCA9984/hw1.0),\ $(if $(filter $(suffix $(1)),.QCA99X0 .qca99x0),\ $(call ipq-wifi-install-one-to,$(1),$(2),QCA99X0/hw2.0),\ - $(if $(filter $(suffix $(1)),.IPQ8074 .ipq8074),\ + $(if $(filter $(suffix $(1)),.IPQ8074 .ipq8074 .ipq8174),\ $(call ipq-wifi-install-ath11-one-to,$(1),$(2),IPQ8074/hw2.0),\ $(if $(filter $(suffix $(1)),.QCN9074 .qcn9074),\ $(call ipq-wifi-install-ath11-one-to,$(1),$(2),QCN9074/hw1.0),\ @@ -144,6 +145,7 @@ $(eval $(call generate-ipq-wifi-package,compex_wpq873,Compex WPQ-873)) $(eval $(call generate-ipq-wifi-package,dynalink_dl-wrx36,Dynalink DL-WRX36)) $(eval $(call generate-ipq-wifi-package,edgecore_eap102,Edgecore EAP102)) $(eval $(call generate-ipq-wifi-package,edimax_cax1800,Edimax CAX1800)) +$(eval $(call generate-ipq-wifi-package,linksys_mx4200,Linksys MX4200)) $(eval $(call generate-ipq-wifi-package,netgear_rax120v2,Netgear RAX120v2)) $(eval $(call generate-ipq-wifi-package,netgear_wax218,Netgear WAX218)) $(eval $(call generate-ipq-wifi-package,netgear_wax620,Netgear WAX620)) diff --git a/package/system/mtd/src/Makefile b/package/system/mtd/src/Makefile index e204ecb221..a1277a6739 100644 --- a/package/system/mtd/src/Makefile +++ b/package/system/mtd/src/Makefile @@ -20,6 +20,7 @@ obj.mvebu = linksys_bootcount.o obj.kirkwood = linksys_bootcount.o obj.ipq806x = linksys_bootcount.o obj.ipq40xx = linksys_bootcount.o +obj.qualcommax = linksys_bootcount.o ifdef FIS_SUPPORT obj += fis.o diff --git a/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8174-mx4200.dtsi b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8174-mx4200.dtsi new file mode 100644 index 0000000000..ef67742c03 --- /dev/null +++ b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8174-mx4200.dtsi @@ -0,0 +1,440 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* Copyright (c) 2023, Mohammad Sayful Islam */ + +#include "ipq8074.dtsi" +#include "ipq8074-ac-cpu.dtsi" +#include "ipq8074-ess.dtsi" +#include +#include +#include + +/ { + + aliases { + serial0 = &blsp1_uart5; + serial1 = &blsp1_uart3; + /* + * Aliases as required by u-boot + * to patch MAC addresses + */ + ethernet1 = &dp2; + ethernet2 = &dp3; + ethernet3 = &dp4; + ethernet4 = &dp5; + led-boot = &led_system_blue; + led-running = &led_system_blue; + led-failsafe = &led_system_red; + led-upgrade = &led_system_green; + }; + + chosen { + stdout-path = "serial0:115200n8"; + bootargs-append = " root=/dev/ubiblock0_0"; + }; + + keys { + compatible = "gpio-keys"; + pinctrl-0 = <&button_pins>; + pinctrl-names = "default"; + + reset-button { + label = "reset"; + gpios = <&tlmm 52 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps-button { + label = "wps"; + gpios = <&tlmm 67 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; +}; + +&tlmm { + button_pins: button-state { + pins = "gpio52", "gpio67"; + function = "gpio"; + drive-strength = <8>; + bias-pull-up; + }; + + mdio_pins: mdio-state { + mdc-pins { + pins = "gpio68"; + function = "mdc"; + drive-strength = <8>; + bias-pull-up; + }; + + mdio-pins { + pins = "gpio69"; + function = "mdio"; + drive-strength = <8>; + bias-pull-up; + }; + }; + + iot_pins: iot-state { + recovery-pins { + pins = "gpio22"; + function = "gpio"; + input; + }; + + reset-pins { + pins = "gpio21"; + function = "gpio"; + bias-pull-up; + }; + }; +}; + +&blsp1_uart3 { + status = "okay"; + + pinctrl-0 = <&hsuart_pins &iot_pins>; + pinctrl-names = "default"; + + /* Silicon Labs EFR32MG21 IoT */ +}; + +&blsp1_uart5 { + status = "okay"; +}; + +&prng { + status = "okay"; +}; + +&cryptobam { + status = "okay"; +}; + +&crypto { + status = "okay"; +}; + +&qpic_bam { + status = "okay"; +}; + +&qpic_nand { + status = "okay"; + + /* + * Bootloader will find the NAND DT node by the compatible and + * then "fixup" it by adding the partitions from the SMEM table + * using the legacy bindings thus making it impossible for us + * to change the partition table or utilize NVMEM for calibration. + * So add a dummy partitions node that bootloader will populate + * and set it as disabled so the kernel ignores it instead of + * printing warnings due to the broken way bootloader adds the + * partitions. + */ + partitions { + status = "disabled"; + }; + + nand@0 { + reg = <0>; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + nand-bus-width = <8>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "0:sbl1"; + reg = <0x0 0x100000>; + read-only; + }; + + partition@100000 { + label = "0:mibib"; + reg = <0x100000 0x100000>; + read-only; + }; + + partition@200000 { + label = "0:bootconfig"; + reg = <0x200000 0x80000>; + read-only; + }; + + partition@280000 { + label = "0:bootconfig1"; + reg = <0x280000 0x80000>; + read-only; + }; + + partition@300000 { + label = "0:qsee"; + reg = <0x300000 0x300000>; + read-only; + }; + + partition@600000 { + label = "0:qsee_1"; + reg = <0x600000 0x300000>; + read-only; + }; + + partition@900000 { + label = "0:devcfg"; + reg = <0x900000 0x80000>; + read-only; + }; + + partition@980000 { + label = "0:devcfg_1"; + reg = <0x980000 0x80000>; + read-only; + }; + + partition@a00000 { + label = "0:apdp"; + reg = <0xa00000 0x80000>; + read-only; + }; + + partition@a80000 { + label = "0:apdp_1"; + reg = <0xa80000 0x80000>; + read-only; + }; + + partition@b00000 { + label = "0:rpm"; + reg = <0xb00000 0x80000>; + read-only; + }; + + partition@b80000 { + label = "0:rpm_1"; + reg = <0xb80000 0x80000>; + read-only; + }; + + partition@c00000 { + label = "0:cdt"; + reg = <0xc00000 0x80000>; + read-only; + }; + + partition@c80000 { + label = "0:cdt_1"; + reg = <0xc80000 0x80000>; + read-only; + }; + + partition@d00000 { + label = "0:appsblenv"; + reg = <0xd00000 0x80000>; + }; + + partition@d80000 { + label = "0:appsbl"; + reg = <0xd80000 0x100000>; + read-only; + }; + + partition@e80000 { + label = "0:appsbl_1"; + reg = <0xe80000 0x100000>; + read-only; + }; + + partition@f80000 { + label = "0:art"; + reg = <0xf80000 0x80000>; + read-only; + }; + + partition@1000000 { + label = "u_env"; + reg = <0x1000000 0x40000>; + }; + + partition@1040000 { + label = "s_env"; + reg = <0x1040000 0x20000>; + }; + + partition@1060000 { + label = "devinfo"; + reg = <0x1060000 0x20000>; + read-only; + }; + + partition@1080000 { + label = "kernel"; + reg = <0x1080000 0x9600000>; + }; + + partition@1680000 { + label = "rootfs"; + reg = <0x1680000 0x9000000>; + }; + + partition@a680000 { + label = "alt_kernel"; + reg = <0xa680000 0x9600000>; + }; + + partition@ac80000 { + label = "alt_rootfs"; + reg = <0xac80000 0x9000000>; + }; + partition@13c80000 { + label = "sysdiag"; + reg = <0x13c80000 0x200000>; + read-only; + }; + partition@13e80000 { + label = "0:ethphyfw"; + reg = <0x13e80000 0x80000>; + read-only; + }; + partition@13f00000 { + label = "syscfg"; + reg = <0x13f00000 0xb800000>; + read-only; + }; + partition@1f700000 { + label = "0:wififw"; + reg = <0x1f700000 0x900000>; + read-only; + }; + }; + }; +}; + +&blsp1_i2c2 { + status = "okay"; + + led-controller@62 { + compatible = "nxp,pca9633"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x62>; + nxp,hw-blink; + + led_system_red: led@0 { + reg = <0>; + color = ; + function = LED_FUNCTION_STATUS; + }; + + led_system_green: led@1 { + reg = <1>; + color = ; + function = LED_FUNCTION_STATUS; + }; + + led_system_blue: led@2 { + reg = <2>; + color = ; + function = LED_FUNCTION_STATUS; + }; + }; +}; + +&mdio { + status = "okay"; + + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + reset-gpios = <&tlmm 37 GPIO_ACTIVE_LOW>; + + qca8075_1: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; + + qca8075_2: ethernet-phy@2 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <2>; + }; + + qca8075_3: ethernet-phy@3 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <3>; + }; + + qca8075_4: ethernet-phy@4 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <4>; + }; +}; + +&switch { + status = "okay"; + + switch_lan_bmp = <(ESS_PORT3 | ESS_PORT4 | ESS_PORT5)>; /* lan port bitmap */ + switch_wan_bmp = ; /* wan port bitmap */ + switch_mac_mode = ; /* mac mode for uniphy instance0*/ + + qcom,port_phyinfo { + port@2 { + port_id = <2>; + phy_address = <1>; + }; + port@3 { + port_id = <3>; + phy_address = <2>; + }; + port@4 { + port_id = <4>; + phy_address = <3>; + }; + port@5 { + port_id = <5>; + phy_address = <4>; + }; + }; +}; + +&edma { + status = "okay"; +}; + +&dp2 { + status = "okay"; + phy-handle = <&qca8075_1>; + label = "wan"; +}; + +&dp3 { + status = "okay"; + phy-handle = <&qca8075_2>; + label = "lan1"; +}; + +&dp4 { + status = "okay"; + phy-handle = <&qca8075_3>; + label = "lan2"; +}; + +&dp5 { + status = "okay"; + phy-handle = <&qca8075_4>; + label = "lan3"; +}; + +&ssphy_0 { + status = "okay"; +}; + +&qusb_phy_0 { + status = "okay"; +}; + +&usb_0 { + status = "okay"; +}; + diff --git a/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8174-mx4200v1.dts b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8174-mx4200v1.dts new file mode 100644 index 0000000000..4bc1b8cc28 --- /dev/null +++ b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8174-mx4200v1.dts @@ -0,0 +1,19 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* Copyright (c) 2023, Mohammad Sayful Islam */ + +/dts-v1/; + +#include "ipq8074-512m.dtsi" +#include "ipq8174-mx4200.dtsi" + +/ { + model = "Linksys MX4200v1"; + compatible = "linksys,mx4200v1", "qcom,ipq8074"; +}; + +&wifi { + status = "okay"; + + qcom,ath11k-calibration-variant = "Linksys-MX4200v1"; + qcom,ath11k-fw-memory-mode = <1>; +}; diff --git a/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8174-mx4200v2.dts b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8174-mx4200v2.dts new file mode 100644 index 0000000000..44e1b72f16 --- /dev/null +++ b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8174-mx4200v2.dts @@ -0,0 +1,17 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* Copyright (c) 2023, Mohammad Sayful Islam */ + +/dts-v1/; + +#include "ipq8174-mx4200.dtsi" + +/ { + model = "Linksys MX4200v2"; + compatible = "linksys,mx4200v2", "qcom,ipq8074"; +}; + +&wifi { + status = "okay"; + + qcom,ath11k-calibration-variant = "Linksys-MX4200v2"; +}; diff --git a/target/linux/qualcommax/image/ipq807x.mk b/target/linux/qualcommax/image/ipq807x.mk index d8416d10fb..5beff11309 100644 --- a/target/linux/qualcommax/image/ipq807x.mk +++ b/target/linux/qualcommax/image/ipq807x.mk @@ -115,6 +115,31 @@ define Device/edimax_cax1800 endef TARGET_DEVICES += edimax_cax1800 +define Device/linksys_mx4200v1 + $(call Device/FitImage) + $(call Device/UbiFit) + DEVICE_VENDOR := Linksys + DEVICE_MODEL := MX4200 + DEVICE_VARIANT := v1 + BLOCKSIZE := 128k + PAGESIZE := 2048 + KERNEL_SIZE := 6144k + IMAGE_SIZE := 147456k + NAND_SIZE := 512m + KERNEL_IN_UBI := + SOC := ipq8174 + IMAGES += factory.bin + IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=MX4200 + DEVICE_PACKAGES := kmod-leds-pca963x ipq-wifi-linksys_mx4200 kmod-bluetooth +endef +TARGET_DEVICES += linksys_mx4200v1 + +define Device/linksys_mx4200v2 + $(call Device/linksys_mx4200v1) + DEVICE_VARIANT := v2 +endef +TARGET_DEVICES += linksys_mx4200v2 + define Device/netgear_rax120v2 $(call Device/FitImage) $(call Device/UbiFit) diff --git a/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network b/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network index 5da17db3fa..ff9069091f 100644 --- a/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network +++ b/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network @@ -18,6 +18,8 @@ ipq807x_setup_interfaces() ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan" ;; compex,wpq873|\ + linksys,mx4200v1|\ + linksys,mx4200v2|\ redmi,ax6|\ xiaomi,ax3600) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" "wan" diff --git a/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata b/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata index ac1405739d..85d107079e 100644 --- a/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata +++ b/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata @@ -15,6 +15,8 @@ case "$FIRMWARE" in dynalink,dl-wrx36|\ edgecore,eap102|\ edimax,cax1800|\ + linksys,mx4200v1|\ + linksys,mx4200v2|\ netgear,rax120v2|\ netgear,wax218|\ netgear,wax620|\ diff --git a/target/linux/qualcommax/ipq807x/base-files/etc/init.d/bootcount b/target/linux/qualcommax/ipq807x/base-files/etc/init.d/bootcount index 84f826b3b8..f5f6c909e9 100755 --- a/target/linux/qualcommax/ipq807x/base-files/etc/init.d/bootcount +++ b/target/linux/qualcommax/ipq807x/base-files/etc/init.d/bootcount @@ -10,5 +10,9 @@ boot() { # Unset changed flag after sysupgrade complete fw_setenv changed ;; + linksys,mx4200v1|\ + linksys,mx4200v2) + mtd resetbc s_env || true + ;; esac } diff --git a/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh b/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh index 67fd0f5402..78842e1c4d 100644 --- a/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh +++ b/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh @@ -73,6 +73,21 @@ platform_do_upgrade() { fw_setenv upgrade_available 1 nand_do_upgrade "$1" ;; + linksys,mx4200v1|\ + linksys,mx4200v2) + boot_part="$(fw_printenv -n boot_part)" + if [ "$boot_part" -eq "1" ]; then + fw_setenv boot_part 2 + CI_KERNPART="alt_kernel" + CI_UBIPART="alt_rootfs" + else + fw_setenv boot_part 1 + CI_UBIPART="rootfs" + fi + fw_setenv boot_part_ready 3 + fw_setenv auto_recovery yes + nand_do_upgrade "$1" + ;; prpl,haze|\ qnap,301w) kernelname="0:HLOS"