From: Sergey Filippov Date: Sat, 15 Jun 2024 19:36:43 +0000 (+0200) Subject: ipq806x: add support for Linksys e8350-v1 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=45b3c620e597c56a4eedb864b5e900d89340e986;p=openwrt%2Fstaging%2Fxback.git ipq806x: add support for Linksys e8350-v1 AC2400 Dual-Band Gigabit Wi-Fi Router base on ipq8064. https://www.linksys.com/support-product?sku=E8350 Specification: - Qualcomm dual-core IPQ8064 @ 1.4 GHz - 512 MB of RAM - 4 MB of SPI NOR MX25U3235F - 128 MB of NAND S34MS01G2 - Qualcomm QCA9880 2.4GHz 802.11bgn - Quantenna QSR1000 5GHz 802.11ac (no support) - 4 x 10/100/1000 Mbit/s w/ vlan support Ethernet - Qualcomm Atheros QCA8337 switch - 1 x 3.0 + 1 x 2.0 (combo with eSata port) - 115200, 8N1 internal serial console - Power, Reset, WPS and WLAN buttons - Power, WPS and WLAN leds - 12 VDC, 3 A power Installation: The installation must be done using web interface of the router. To achive this new firmware-utils tool was added to set correct magic headers for the factory images. Installation from vendor firmware: 1. Flash over the native Linksys WEB interface using factory image. Installation using recovery mode: 1. Power off the device and disconnect the WAN port. (Only LAN port to be connected) 2. Press & hold the "Reset" button 3. Power on the device & wait 10 seconds with pressed "Reset" button 4. Set IP Internet Protocol on your PC from 192.168.1.0/24 network (Router is on IP 192.168.1.1) 5. Open the Firmware Recovery page in your browser: http://192.168.1.1/index.shtml Firmware Recovery -> File Name -> Recovery & Reboot The device page in inbox: https://openwrt.org/inbox/toh/linksys/linksys_ea8350_1 Signed-off-by: Sergey Filippov Link: https://github.com/openwrt/openwrt/pull/15798 Signed-off-by: Christian Marangi --- diff --git a/target/linux/ipq806x/base-files/etc/board.d/01_leds b/target/linux/ipq806x/base-files/etc/board.d/01_leds index 4aab3c9b2c..c96d5e69c4 100644 --- a/target/linux/ipq806x/base-files/etc/board.d/01_leds +++ b/target/linux/ipq806x/base-files/etc/board.d/01_leds @@ -46,6 +46,9 @@ fortinet,fap-421e) ucidef_set_led_wlan "wlan5g" "5G" "yellow:5g" "phy0tpt" ucidef_set_led_usbport "usb" "USB" "amber:power" "usb1-port1" "usb2-port1" ;; +linksys,e8350-v1) + ucidef_set_led_wlan "wlan" "WLAN" "green:wifi" "phy0tpt" + ;; meraki,mr52) ucidef_set_led_netdev "eth0" "eth0" "green:lan1" "eth0" ucidef_set_led_netdev "eth1" "eth1" "green:lan2" "eth1" diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network index a408fc14ac..77d47b8cd0 100644 --- a/target/linux/ipq806x/base-files/etc/board.d/02_network +++ b/target/linux/ipq806x/base-files/etc/board.d/02_network @@ -23,6 +23,7 @@ ipq806x_setup_interfaces() netgear,r7500 |\ netgear,r7500v2 |\ qcom,ipq8064-ap148 |\ + linksys,e8350-v1 |\ linksys,ea7500-v1 |\ linksys,ea8500 |\ nec,wg2600hp3 |\ @@ -87,6 +88,7 @@ ipq806x_setup_macs() ucidef_set_interface_macaddr "lan" "$hw_mac_addr" ucidef_set_interface_macaddr "wan" "$hw_mac_addr" ;; + linksys,e8350-v1 |\ zyxel,nbg6817) hw_mac_addr=$(mtd_get_mac_ascii 0:appsblenv ethaddr) ucidef_set_interface_macaddr "lan" "$(macaddr_add $hw_mac_addr 2)" diff --git a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh index b3a615a511..f26f118d54 100644 --- a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh @@ -14,6 +14,7 @@ platform_do_upgrade() { askey,rt4230w-rev6 |\ compex,wpq864|\ fortinet,fap-421e|\ + linksys,e8350-v1|\ netgear,d7800 |\ netgear,r7500 |\ netgear,r7500v2 |\ diff --git a/target/linux/ipq806x/files-6.6/arch/arm/boot/dts/qcom/qcom-ipq8064-e8350-v1.dts b/target/linux/ipq806x/files-6.6/arch/arm/boot/dts/qcom/qcom-ipq8064-e8350-v1.dts new file mode 100644 index 0000000000..2bd34c3032 --- /dev/null +++ b/target/linux/ipq806x/files-6.6/arch/arm/boot/dts/qcom/qcom-ipq8064-e8350-v1.dts @@ -0,0 +1,428 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +#include "qcom-ipq8064-v2.0-smb208.dtsi" + +#include +#include + +/ { + model = "Linksys E8350 V1 WiFi Router"; + compatible = "linksys,e8350-v1", "qcom,ipq8064"; + + memory@0 { + reg = <0x42000000 0x1e000000>; + device_type = "memory"; + }; + + aliases { + serial0 = &gsbi4_serial; + + led-boot = &led_power; + led-failsafe = &led_power; + led-running = &led_power; + led-upgrade = &led_power; + }; + + keys { + compatible = "gpio-keys"; + pinctrl-0 = <&button_pins>; + pinctrl-names = "default"; + + reset { + label = "reset"; + gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <60>; + wakeup-source; + }; + + wps { + label = "wps"; + gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <60>; + wakeup-source; + }; + + wifi { + label = "wifi"; + gpios = <&qcom_pinmux 67 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <60>; + wakeup-source; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&led_pins>; + pinctrl-names = "default"; + + led_power: power { + label = "green:power"; + gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + + wps { + label = "green:wps"; + gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; + }; + + wifi { + label = "green:wifi"; + gpios = <&qcom_pinmux 54 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&nand { + status = "okay"; + + #address-cells = <1>; + #size-cells = <1>; + + nand@0 { + reg = <0>; + + nand-ecc-strength = <4>; + nand-bus-width = <8>; + + partitions { + compatible = "fixed-partitions"; + + partition@0 { + label = "ubi"; + reg = <0 0x4000000>; + }; + partition@4000000 { + label = "extra"; + reg = <0x4000000 0x4000000>; + }; + }; + }; +}; + +&qcom_pinmux { + button_pins: button_pins { + mux { + pins = "gpio68","gpio65", "gpio67"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + led_pins: led_pins { + mux { + pins = "gpio26","gpio53", "gpio54"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + switch_reset: switch_reset_pins { + mux { + pins = "gpio63"; + function = "gpio"; + drive-strength = <12>; + bias-pull-up; + }; + }; +}; + +&gsbi5 { + qcom,mode = ; + status = "okay"; + + spi5: spi@1a280000 { + status = "okay"; + + pinctrl-0 = <&spi_pins>; + pinctrl-names = "default"; + + cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; + + m25p80@0 { + compatible = "jedec,spi-nor"; + spi-max-frequency = <51200000>; + reg = <0>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "0:sbl1"; + reg = <0x0000000 0x0010000>; + read-only; + }; + + partition@10000 { + label = "0:mibib"; + reg = <0x0010000 0x0020000>; + read-only; + }; + + partition@30000 { + label = "0:sbl2"; + reg = <0x0030000 0x0020000>; + read-only; + }; + + partition@50000 { + label = "0:sbl3"; + reg = <0x0050000 0x0030000>; + read-only; + }; + + partition@80000 { + label = "0:ddrconfig"; + reg = <0x0080000 0x0010000>; + read-only; + }; + + partition@90000 { + label = "0:ssd"; + reg = <0x0090000 0x0010000>; + read-only; + }; + + partition@a0000 { + label = "0:tz"; + reg = <0x00a0000 0x0030000>; + read-only; + }; + + partition@d0000 { + label = "0:rpm"; + reg = <0x00d0000 0x0020000>; + read-only; + }; + + partition@f0000 { + label = "0:oldappsbl"; + reg = <0x00f0000 0x0040000>; + read-only; + }; + + partition@130000 { + label = "0:appsblenv"; + reg = <0x0130000 0x0040000>; + read-only; + }; + + art: partition@170000 { + label = "0:ART"; + reg = <0x0170000 0x0020000>; + read-only; + }; + + partition@190000 { + label = "0:uboot"; + reg = <0x0190000 0x0050000>; + read-only; + }; + + partition@1e0000 { + label = "0:oldnss1"; + reg = <0x01e0000 0x0020000>; + read-only; + }; + + partition@200000 { + label = "0:nvram"; + reg = <0x0200000 0x0020000>; + read-only; + }; + + partition@220000 { + label = "0:oldkernel"; + reg = <0x0220000 0x01e0000>; + read-only; + }; + }; + }; + }; +}; + +&hs_phy_0 { + status = "okay"; +}; + +&ss_phy_0 { + status = "okay"; +}; + +&usb3_0 { + status = "okay"; +}; + +&hs_phy_1 { + status = "okay"; +}; + +&ss_phy_1 { + status = "okay"; +}; + +&usb3_1 { + status = "okay"; +}; + +&pcie0 { + status = "okay"; + + max-link-speed = <1>; +}; + +&pcie1 { + status = "okay"; +}; + +&mdio0 { + status = "okay"; + + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; + + /* Switch from documentation require at least 12ms for reset */ + reset-gpios = <&qcom_pinmux 63 GPIO_ACTIVE_HIGH>; + reset-post-delay-us = <12000>; + + switch@10 { + compatible = "qca,qca8337"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x10>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "cpu"; + ethernet = <&gmac1>; + phy-mode = "rgmii"; + tx-internal-delay-ps = <1000>; + rx-internal-delay-ps = <1000>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + port@1 { + reg = <1>; + label = "lan1"; + phy-mode = "internal"; + phy-handle = <&phy_port1>; + }; + + port@2 { + reg = <2>; + label = "lan2"; + phy-mode = "internal"; + phy-handle = <&phy_port2>; + }; + + port@3 { + reg = <3>; + label = "lan3"; + phy-mode = "internal"; + phy-handle = <&phy_port3>; + }; + + port@4 { + reg = <4>; + label = "lan4"; + phy-mode = "internal"; + phy-handle = <&phy_port4>; + }; + + port@5 { + reg = <5>; + label = "wan"; + phy-mode = "internal"; + phy-handle = <&phy_port5>; + }; + + port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&gmac2>; + phy-mode = "sgmii"; + qca,sgmii-enable-pll; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy_port1: phy@0 { + reg = <0>; + }; + + phy_port2: phy@1 { + reg = <1>; + }; + + phy_port3: phy@2 { + reg = <2>; + }; + + phy_port4: phy@3 { + reg = <3>; + }; + + phy_port5: phy@4 { + reg = <4>; + }; + }; + }; +}; + +&gmac1 { + status = "okay"; + + phy-mode = "rgmii"; + qcom,id = <1>; + + pinctrl-0 = <&rgmii2_pins>; + pinctrl-names = "default"; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&gmac2 { + status = "okay"; + + phy-mode = "sgmii"; + qcom,id = <2>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&tcsr { + qcom,usb-ctrl-select = ; + compatible = "qcom,tcsr", "syscon"; +}; + +&adm_dma { + status = "okay"; +}; diff --git a/target/linux/ipq806x/image/generic.mk b/target/linux/ipq806x/image/generic.mk index 98e74e5b11..b5bf8898ab 100644 --- a/target/linux/ipq806x/image/generic.mk +++ b/target/linux/ipq806x/image/generic.mk @@ -35,6 +35,18 @@ define Build/edimax-header @mv $@.new $@ endef +# tune addpattern for Linksys E8350-V1 fw pattern generation +define Build/linksys-bin + $(STAGING_DIR_HOST)/bin/addpattern -p $(FW_DEVICE_ID) -v $(FW_VERSION) $(if $(SERIAL),-s $(SERIAL)) -i $@ -o $@.new + mv $@.new $@ +endef + +# Use Linksys fw header generator to upgrade openwrt factory image over the native Linksys WEB interface +define Build/linksys-addfwhdr + -$(STAGING_DIR_HOST)/bin/linksys-addfwhdr -i $@ -o $@.new \ + ;mv "$@.new" "$@" +endef + define Device/DniImage KERNEL_SUFFIX := -uImage KERNEL = kernel-bin | append-dtb | uImage none @@ -189,6 +201,23 @@ define Device/fortinet_fap-421e endef TARGET_DEVICES += fortinet_fap-421e +define Device/linksys_e8350-v1 + $(call Device/LegacyImage) + DEVICE_VENDOR := Linksys + DEVICE_MODEL := E8350 + DEVICE_VARIANT := v1 + SOC := qcom-ipq8064 + FW_VERSION := v1.0.03.003 + FW_DEVICE_ID := 8350 + PAGESIZE := 2048 + BLOCKSIZE := 128k + KERNEL_IN_UBI := 1 + IMAGES = factory.bin sysupgrade.bin + IMAGE/factory.bin := append-ubi | check-size 0x04000000 | linksys-addfwhdr | linksys-bin + DEVICE_PACKAGES := ath10k-firmware-qca988x-ct +endef +TARGET_DEVICES += linksys_e8350-v1 + define Device/linksys_ea7500-v1 $(call Device/LegacyImage) $(Device/kernel-size-migration)