From: Robert Marko Date: Mon, 7 Sep 2020 10:50:45 +0000 (+0200) Subject: ipq40xx: add Edgecore ECW5211 support X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=4488b260a02e169d6902df44debbe9b3c8e001cc;p=openwrt%2Fstaging%2Fneocturne.git ipq40xx: add Edgecore ECW5211 support This patch adds support for the Edgecore ECW5211 indoor AP. Specification: - SoC: Qualcomm Atheros IPQ4018 ARMv7-A 4x Cortex A-7 - RAM: 256MB DDR3 - NOR Flash: 16MB SPI NOR - NAND Flash: 128MB MX35LFxGE4AB SPI-NAND - Ethernet: 2 x 1G via Q8075 PHY connected to ethernet adapter via PSGMII (802.3af POE IN on eth0) - USB: 1 x USB 3.0 SuperSpeed - WLAN: Built-in IPQ4018 (2x2 802.11bng, 2x2 802.11 acn) - CC2540 BLE connected to USB 2.0 port - Atmel AT97SC3205T I2C TPM Signed-off-by: Robert Marko --- diff --git a/package/boot/uboot-envtools/files/ipq40xx b/package/boot/uboot-envtools/files/ipq40xx index f427661cf7..76a3346110 100644 --- a/package/boot/uboot-envtools/files/ipq40xx +++ b/package/boot/uboot-envtools/files/ipq40xx @@ -32,6 +32,7 @@ ubootenv_mtdinfo () { case "$board" in alfa-network,ap120c-ac |\ +edgecore,ecw5211 |\ glinet,gl-b1300 |\ openmesh,a42 |\ openmesh,a62) diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile index a796910186..963cf2d7c4 100644 --- a/package/firmware/ipq-wifi/Makefile +++ b/package/firmware/ipq-wifi/Makefile @@ -31,6 +31,7 @@ ALLWIFIBOARDS:= \ buffalo_wtr-m2133hp \ cellc_rtl30vw \ dlink_dap2610 \ + edgecore_ecw5211 \ edgecore_ecw5410 \ engenius_eap2200 \ engenius_emd1 \ @@ -106,6 +107,7 @@ $(eval $(call generate-ipq-wifi-package,avm_fritzrepeater-1200,AVM FRITZRepeater $(eval $(call generate-ipq-wifi-package,buffalo_wtr-m2133hp,Buffalo WTR-M2133HP)) $(eval $(call generate-ipq-wifi-package,cellc_rtl30vw, Cell C RTL30VW)) $(eval $(call generate-ipq-wifi-package,dlink_dap2610,D-Link DAP-2610)) +$(eval $(call generate-ipq-wifi-package,edgecore_ecw5211,Edgecore ECW5211)) $(eval $(call generate-ipq-wifi-package,edgecore_ecw5410,Edgecore ECW5410)) $(eval $(call generate-ipq-wifi-package,engenius_eap2200,EnGenius EAP2200)) $(eval $(call generate-ipq-wifi-package,engenius_emd1,EnGenius EMD1)) diff --git a/package/firmware/ipq-wifi/board-edgecore_ecw5211.qca4019 b/package/firmware/ipq-wifi/board-edgecore_ecw5211.qca4019 new file mode 100644 index 0000000000..340cfcc7a2 Binary files /dev/null and b/package/firmware/ipq-wifi/board-edgecore_ecw5211.qca4019 differ diff --git a/target/linux/ipq40xx/base-files/etc/board.d/01_leds b/target/linux/ipq40xx/base-files/etc/board.d/01_leds index 0a128e8cbc..e9e0de9da9 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/01_leds +++ b/target/linux/ipq40xx/base-files/etc/board.d/01_leds @@ -62,6 +62,7 @@ zyxel,nbg6617) ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:green:wlan2G" "phy0tpt" ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:green:wlan5G" "phy1tpt" ;; +edgecore,ecw5211 |\ zyxel,wre6606) ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:green:wlan2g" "phy0tpt" ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:green:wlan5g" "phy1tpt" diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index 61d02a17bc..571479aaf2 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -38,6 +38,7 @@ ipq40xx_setup_interfaces() ;; asus,map-ac2200|\ cilab,meshpoint-one|\ + edgecore,ecw5211|\ openmesh,a42|\ openmesh,a62) ucidef_set_interfaces_lan_wan "eth1" "eth0" diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 8df7990f2e..d85424142b 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -93,6 +93,7 @@ case "$FIRMWARE" in cellc,rtl30vw |\ compex,wpj419 |\ compex,wpj428 |\ + edgecore,ecw5211 |\ engenius,eap1300 |\ engenius,eap2200 |\ openmesh,a42 |\ @@ -186,6 +187,7 @@ case "$FIRMWARE" in cellc,rtl30vw |\ compex,wpj419 |\ compex,wpj428 |\ + edgecore,ecw5211 |\ engenius,eap1300 |\ engenius,eap2200 |\ openmesh,a42 |\ diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh index 5b89710a22..ae5a0a7c1b 100644 --- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh @@ -66,6 +66,7 @@ platform_do_upgrade() { avm,fritzrepeater-3000 |\ buffalo,wtr-m2133hp |\ cilab,meshpoint-one |\ + edgecore,ecw5211 |\ engenius,eap2200 |\ mobipromo,cm520-79f |\ qxwlan,e2600ac-c2) diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-ecw5211.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-ecw5211.dts new file mode 100644 index 0000000000..3f7e2ad6fd --- /dev/null +++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-ecw5211.dts @@ -0,0 +1,325 @@ +#include "qcom-ipq4019.dtsi" +#include +#include +#include + +/ { + model = "Edgecore ECW5211"; + compatible = "edgecore,ecw5211"; + + aliases { + led-boot = &led_power; + led-failsafe = &led_power; + led-running = &led_power; + led-upgrade = &led_power; + }; + + chosen { + bootargs-append = " root=/dev/ubiblock0_1"; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&tlmm 63 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_power: power { + label = "ecw5211:yellow:power"; + gpios = <&tlmm 5 GPIO_ACTIVE_LOW>; + }; + + wlan2g { + label = "ecw5211:green:wlan2g"; + gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>; + }; + + wlan5g { + label = "ecw5211:green:wlan5g"; + gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>; + }; + }; + + soc { + rng@22000 { + status = "okay"; + }; + + mdio@90000 { + status = "okay"; + + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + counter@4a1000 { + compatible = "qcom,qca-gcnt"; + reg = <0x4a1000 0x4>; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = ; + }; + + tcsr@194b000 { + status = "okay"; + + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = ; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = ; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = ; + }; + + usb2: usb2@60f8800 { + status = "okay"; + }; + + usb3: usb3@8af8800 { + status = "okay"; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + watchdog@b017000 { + status = "okay"; + }; + + ess-switch@c000000 { + status = "okay"; + }; + + edma@c080000 { + status = "okay"; + }; + }; +}; + +&tlmm { + mdio_pins: mdio_pinmux { + mux_mdio { + pins = "gpio53"; + function = "mdio"; + bias-pull-up; + }; + + mux_mdc { + pins = "gpio52"; + function = "mdc"; + bias-pull-up; + }; + }; + + serial_pins: serial_pinmux { + mux { + pins = "gpio60", "gpio61"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + spi0_pins: spi0_pinmux { + pin { + function = "blsp_spi0"; + pins = "gpio55", "gpio56", "gpio57"; + drive-strength = <2>; + bias-disable; + }; + + pin_cs { + function = "gpio"; + pins = "gpio54", "gpio4"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; + + i2c0_pins: i2c0_pinmux { + mux_i2c { + function = "blsp_i2c0"; + pins = "gpio58", "gpio59"; + drive-strength = <16>; + bias-disable; + }; + }; +}; + +&blsp_dma { + status = "okay"; +}; + +&blsp1_spi1 { + status = "okay"; + + pinctrl-0 = <&spi0_pins>; + pinctrl-names = "default"; + cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>, <&tlmm 4 GPIO_ACTIVE_HIGH>; + + flash@0 { + status = "okay"; + + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "0:SBL1"; + reg = <0x00000000 0x00040000>; + read-only; + }; + + partition@40000 { + label = "0:MIBIB"; + reg = <0x00040000 0x00020000>; + read-only; + }; + + partition@60000 { + label = "0:QSEE"; + reg = <0x00060000 0x00060000>; + read-only; + }; + + partition@c0000 { + label = "0:CDT"; + reg = <0x000c0000 0x00010000>; + read-only; + }; + + partition@d0000 { + label = "0:DDRPARAMS"; + reg = <0x000d0000 0x00010000>; + read-only; + }; + + partition@e0000 { + label = "0:APPSBLENV"; /* uboot env*/ + reg = <0x000e0000 0x00010000>; + read-only; + }; + + partition@f0000 { + label = "0:APPSBL"; /* uboot */ + reg = <0x000f0000 0x00080000>; + read-only; + }; + + partition@170000 { + label = "0:ART"; + reg = <0x00170000 0x00010000>; + read-only; + }; + }; + }; + + spi-nand@1 { + status = "okay"; + + compatible = "spi-nand"; + reg = <1>; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "rootfs"; + reg = <0x00000000 0x04000000>; + }; + }; + }; +}; + +&blsp1_i2c3 { + status = "okay"; + + pinctrl-0 = <&i2c0_pins>; + pinctrl-names = "default"; + + tpm@29 { + compatible = "atmel,at97sc3204t"; + reg = <0x29>; + }; +}; + +&blsp1_uart1 { + status = "okay"; + + pinctrl-0 = <&serial_pins>; + pinctrl-names = "default"; +}; + +&cryptobam { + status = "okay"; +}; + +&gmac0 { + qcom,poll_required = <1>; + qcom,poll_required_dynamic = <1>; + qcom,phy_mdio_addr = <4>; + vlan_tag = <2 0x20>; +}; + +&gmac1 { + qcom,poll_required = <1>; + qcom,poll_required_dynamic = <1>; + qcom,phy_mdio_addr = <3>; + vlan_tag = <1 0x10>; +}; + +&wifi0 { + status = "okay"; + + qcom,ath10k-calibration-variant = "Edgecore-ECW5211"; +}; + +&wifi1 { + status = "okay"; + + qcom,ath10k-calibration-variant = "Edgecore-ECW5211"; +}; + +&usb3_ss_phy { + status = "okay"; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&usb2_hs_phy { + status = "okay"; +}; diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile index 51e8bcc7e3..127af99ce5 100644 --- a/target/linux/ipq40xx/image/Makefile +++ b/target/linux/ipq40xx/image/Makefile @@ -344,6 +344,18 @@ define Device/dlink_dap-2610 endef TARGET_DEVICES += dlink_dap-2610 +define Device/edgecore_ecw5211 + $(call Device/FitImage) + $(call Device/UbiFit) + DEVICE_TITLE := Edgecore ECW5211 + BLOCKSIZE := 128k + PAGESIZE := 2048 + DEVICE_DTS_CONFIG := config@ap.dk01.1-c2 + DEVICE_DTS := qcom-ipq4018-ecw5211 + DEVICE_PACKAGES := ipq-wifi-edgecore_ecw5211 kmod-tpm-i2c-atmel kmod-usb-acm uboot-envtools +endef +TARGET_DEVICES += edgecore_ecw5211 + define Device/engenius_eap1300 $(call Device/FitImage) DEVICE_VENDOR := EnGenius diff --git a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch index d281bb468d..ea45606c27 100644 --- a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch @@ -8,9 +8,11 @@ Signed-off-by: John Crispin arch/arm/boot/dts/Makefile | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+) ---- a/arch/arm/boot/dts/Makefile -+++ b/arch/arm/boot/dts/Makefile -@@ -837,11 +837,50 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +Index: linux-5.4.63/arch/arm/boot/dts/Makefile +=================================================================== +--- linux-5.4.63.orig/arch/arm/boot/dts/Makefile ++++ linux-5.4.63/arch/arm/boot/dts/Makefile +@@ -837,11 +837,51 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -20,6 +22,7 @@ Signed-off-by: John Crispin + qcom-ipq4018-cs-w3-wd1200g-eup.dtb \ + qcom-ipq4018-ea6350v3.dtb \ + qcom-ipq4018-eap1300.dtb \ ++ qcom-ipq4018-ecw5211.dtb \ + qcom-ipq4018-emd1.dtb \ + qcom-ipq4018-emr3500.dtb \ + qcom-ipq4018-ens620ext.dtb \