From: Bo Shen Date: Fri, 27 Mar 2015 06:23:34 +0000 (+0800) Subject: ARM: atmel: at91sam9m10g45ek: enable spl support X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=41d41a93fb5600b0cbfdbfae88b0d8403bd650b7;p=project%2Fbcm63xx%2Fu-boot.git ARM: atmel: at91sam9m10g45ek: enable spl support Supports boot up from NAND flash with software ECC eanbled. And supports boot up from SD/MMC card with FAT file system. As the boot from SD/MMC card with FAT file system, the BSS segment is too big to fit into SRAM, so, use the lds to put it into SDRAM. Signed-off-by: Bo Shen --- diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig index 30945c101b..25da9262c5 100644 --- a/arch/arm/mach-at91/Kconfig +++ b/arch/arm/mach-at91/Kconfig @@ -66,6 +66,7 @@ config TARGET_STAMP9G20 config TARGET_AT91SAM9M10G45EK bool "Atmel AT91SAM9M10G45-EK board" select CPU_ARM926EJS + select SUPPORT_SPL config TARGET_PM9G45 bool "Ronetix pm9g45 board" diff --git a/arch/arm/mach-at91/arm926ejs/u-boot-spl.lds b/arch/arm/mach-at91/arm926ejs/u-boot-spl.lds new file mode 100644 index 0000000000..acadd1d4c4 --- /dev/null +++ b/arch/arm/mach-at91/arm926ejs/u-boot-spl.lds @@ -0,0 +1,48 @@ +/* + * Copyright (C) 2015 Atmel Corporation + * Bo Shen + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +MEMORY { .sram : ORIGIN = CONFIG_SPL_TEXT_BASE, \ + LENGTH = CONFIG_SPL_MAX_SIZE } +MEMORY { .sdram : ORIGIN = CONFIG_SPL_BSS_START_ADDR, \ + LENGTH = CONFIG_SPL_BSS_MAX_SIZE } + +OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm") +OUTPUT_ARCH(arm) +ENTRY(_start) +SECTIONS +{ + .text : + { + __start = .; + *(.vectors) + arch/arm/cpu/arm926ejs/start.o (.text*) + *(.text*) + } >.sram + + . = ALIGN(4); + .rodata : { *(SORT_BY_ALIGNMENT(.rodata*)) } >.sram + + . = ALIGN(4); + .data : { *(SORT_BY_ALIGNMENT(.data*)) } >.sram + + . = ALIGN(4); + __image_copy_end = .; + + .end : + { + *(.__end) + } >.sram + + .bss : + { + . = ALIGN(4); + __bss_start = .; + *(.bss*) + . = ALIGN(4); + __bss_end = .; + } >.sdram +} diff --git a/arch/arm/mach-at91/spl_at91.c b/arch/arm/mach-at91/spl_at91.c index 89f588be45..af6fc0d4c6 100644 --- a/arch/arm/mach-at91/spl_at91.c +++ b/arch/arm/mach-at91/spl_at91.c @@ -71,7 +71,11 @@ void __weak at91_spl_board_init(void) { } -void spl_board_init(void) +void __weak spl_board_init(void) +{ +} + +void board_init_f(ulong dummy) { struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; diff --git a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c index b807ef9a42..4289179ee6 100644 --- a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c +++ b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c @@ -8,6 +8,7 @@ #include #include +#include #include #include #include @@ -15,6 +16,7 @@ #include #include #include +#include #include #include #if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB) @@ -71,6 +73,84 @@ void at91sam9m10g45ek_nand_hw_init(void) } #endif +#if defined(CONFIG_SPL_BUILD) +#include +#include + +void at91_spl_board_init(void) +{ + /* + * On the at91sam9m10g45ek board, the chip wm9711 stays in the + * test mode, so it needs do some action to exit test mode. + */ + at91_periph_clk_enable(ATMEL_ID_PIODE); + at91_set_gpio_output(AT91_PIN_PD7, 0); + at91_set_gpio_output(AT91_PIN_PD8, 0); + at91_set_pio_pullup(AT91_PIO_PORTD, 7, 1); + at91_set_pio_pullup(AT91_PIO_PORTD, 8, 1); + +#ifdef CONFIG_SYS_USE_MMC + at91_mci_hw_init(); +#elif CONFIG_SYS_USE_NANDFLASH + at91sam9m10g45ek_nand_hw_init(); +#endif +} + +#include +static void ddr2_conf(struct atmel_mpddr *ddr2) +{ + ddr2->md = (ATMEL_MPDDRC_MD_DBW_16_BITS | ATMEL_MPDDRC_MD_DDR2_SDRAM); + + ddr2->cr = (ATMEL_MPDDRC_CR_NC_COL_10 | + ATMEL_MPDDRC_CR_NR_ROW_14 | + ATMEL_MPDDRC_CR_DQMS_SHARED | + ATMEL_MPDDRC_CR_CAS_DDR_CAS3); + + ddr2->rtr = 0x24b; + + ddr2->tpr0 = (6 << ATMEL_MPDDRC_TPR0_TRAS_OFFSET |/* 6*7.5 = 45 ns */ + 2 << ATMEL_MPDDRC_TPR0_TRCD_OFFSET |/* 2*7.5 = 15 ns */ + 2 << ATMEL_MPDDRC_TPR0_TWR_OFFSET | /* 2*7.5 = 15 ns */ + 8 << ATMEL_MPDDRC_TPR0_TRC_OFFSET | /* 8*7.5 = 60 ns */ + 2 << ATMEL_MPDDRC_TPR0_TRP_OFFSET | /* 2*7.5 = 15 ns */ + 1 << ATMEL_MPDDRC_TPR0_TRRD_OFFSET | /* 1*7.5= 7.5 ns*/ + 1 << ATMEL_MPDDRC_TPR0_TWTR_OFFSET | /* 1 clk cycle */ + 2 << ATMEL_MPDDRC_TPR0_TMRD_OFFSET); /* 2 clk cycles */ + + ddr2->tpr1 = (2 << ATMEL_MPDDRC_TPR1_TXP_OFFSET | /* 2*7.5 = 15 ns */ + 200 << ATMEL_MPDDRC_TPR1_TXSRD_OFFSET | + 16 << ATMEL_MPDDRC_TPR1_TXSNR_OFFSET | + 14 << ATMEL_MPDDRC_TPR1_TRFC_OFFSET); + + ddr2->tpr2 = (1 << ATMEL_MPDDRC_TPR2_TRTP_OFFSET | + 0 << ATMEL_MPDDRC_TPR2_TRPA_OFFSET | + 7 << ATMEL_MPDDRC_TPR2_TXARDS_OFFSET | + 2 << ATMEL_MPDDRC_TPR2_TXARD_OFFSET); +} + +void mem_init(void) +{ + struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; + struct at91_matrix *mat = (struct at91_matrix *)ATMEL_BASE_MATRIX; + struct atmel_mpddr ddr2; + unsigned long csa; + + ddr2_conf(&ddr2); + + /* enable DDR2 clock */ + writel(0x4, &pmc->scer); + + /* Chip select 1 is for DDR2/SDRAM */ + csa = readl(&mat->ebicsa); + csa |= AT91_MATRIX_EBI_CS1A_SDRAMC; + csa &= ~AT91_MATRIX_EBI_VDDIOMSEL_3_3V; + writel(csa, &mat->ebicsa); + + /* DDRAM2 Controller initialize */ + ddr2_init(ATMEL_BASE_CS6, &ddr2); +} +#endif + #ifdef CONFIG_CMD_USB static void at91sam9m10g45ek_usb_hw_init(void) { diff --git a/configs/at91sam9m10g45ek_mmc_defconfig b/configs/at91sam9m10g45ek_mmc_defconfig index 6949d3a007..f3e1ebec93 100644 --- a/configs/at91sam9m10g45ek_mmc_defconfig +++ b/configs/at91sam9m10g45ek_mmc_defconfig @@ -1,3 +1,4 @@ +CONFIG_SPL=y CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9M10G45,SYS_USE_MMC" CONFIG_ARM=y CONFIG_ARCH_AT91=y diff --git a/configs/at91sam9m10g45ek_nandflash_defconfig b/configs/at91sam9m10g45ek_nandflash_defconfig index 30967e39c4..5e0b16e775 100644 --- a/configs/at91sam9m10g45ek_nandflash_defconfig +++ b/configs/at91sam9m10g45ek_nandflash_defconfig @@ -1,3 +1,4 @@ +CONFIG_SPL=y CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9M10G45,SYS_USE_NANDFLASH" CONFIG_ARM=y CONFIG_ARCH_AT91=y diff --git a/include/configs/at91sam9m10g45ek.h b/include/configs/at91sam9m10g45ek.h index db5d5ea846..e4c49f4c14 100644 --- a/include/configs/at91sam9m10g45ek.h +++ b/include/configs/at91sam9m10g45ek.h @@ -203,4 +203,62 @@ */ #define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000) +/* Defines for SPL */ +#define CONFIG_SPL_FRAMEWORK +#define CONFIG_SPL_TEXT_BASE 0x300000 +#define CONFIG_SPL_MAX_SIZE 0x010000 +#define CONFIG_SPL_STACK 0x310000 + +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_GPIO_SUPPORT + +#define CONFIG_SYS_MONITOR_LEN 0x80000 + +#ifdef CONFIG_SYS_USE_MMC + +#define CONFIG_SPL_BSS_START_ADDR 0x70000000 +#define CONFIG_SPL_BSS_MAX_SIZE 0x00080000 +#define CONFIG_SYS_SPL_MALLOC_START 0x70080000 +#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00080000 + +#define CONFIG_SPL_LDSCRIPT arch/arm/mach-at91/arm926ejs/u-boot-spl.lds +#define CONFIG_SPL_MMC_SUPPORT +#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400 +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x200 +#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1 +#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" +#define CONFIG_SPL_FAT_SUPPORT +#define CONFIG_SPL_LIBDISK_SUPPORT + +#elif CONFIG_SYS_USE_NANDFLASH +#define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_DRIVERS +#define CONFIG_SPL_NAND_BASE +#define CONFIG_SPL_NAND_ECC +#define CONFIG_SPL_NAND_SOFTECC +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000 +#define CONFIG_SYS_NAND_U_BOOT_SIZE 0x80000 +#define CONFIG_SYS_NAND_5_ADDR_CYCLE + +#define CONFIG_SYS_NAND_PAGE_SIZE 0x800 +#define CONFIG_SYS_NAND_BLOCK_SIZE 0x20000 +#define CONFIG_SYS_NAND_PAGE_COUNT 64 +#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS +#define CONFIG_SYS_NAND_ECCSIZE 256 +#define CONFIG_SYS_NAND_ECCBYTES 3 +#define CONFIG_SYS_NAND_OOBSIZE 64 +#define CONFIG_SYS_NAND_ECCPOS { 40, 41, 42, 43, 44, 45, 46, 47, \ + 48, 49, 50, 51, 52, 53, 54, 55, \ + 56, 57, 58, 59, 60, 61, 62, 63, } +#endif + +#define CONFIG_SPL_ATMEL_SIZE +#define CONFIG_SYS_MASTER_CLOCK 132096000 +#define CONFIG_SYS_AT91_PLLA 0x20c73f03 +#define CONFIG_SYS_MCKR 0x1301 +#define CONFIG_SYS_MCKR_CSS 0x1302 + +#define ATMEL_BASE_MPDDRC ATMEL_BASE_DDRSDRC0 #endif