From: Petr Štetiar Date: Wed, 12 Dec 2018 20:09:01 +0000 (+0100) Subject: ath79: Add support for Ubiquiti Nanostation M (XW) X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=40530c8eb42aa4b98de10621b6c1c89030f00d0a;p=openwrt%2Fstaging%2Fjow.git ath79: Add support for Ubiquiti Nanostation M (XW) CPU: AR9342 SoC RAM: 64 MB DDR2 Flash: 8 MB NOR SPI Ports: 2x100 MBit (24V PoE in, 24V PoE out), AR8236 switch WLAN: 2.4/5 GHz UART: 1 UART LEDs: Power, 2x Ethernet, 4x RSSI LEDs (orange, red, 2x green) Buttons: Reset Flashing instructions using recovery method over TFTP 1. Unplug the ethernet cable from the router. 2. Using paper clip press and hold the router's reset button. Make sure you can feel it depressed by the paper clip. Do not release the button until step 4. 3. While keeping the reset button pressed in, plug the ethernet cable back into the AP. Keep the reset button depressed until you see the device's LEDs flashing in upgrade mode (alternating LED1/LED3 and LED2/LED4), this may take up to 25 seconds. 4. You may release the reset button, now the device should be in TFTP transfer mode. 5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24 should work. 6. Plug the PoE injector's LAN cable directly to your computer. 7. Start tftp client and issue following commands: tftp> binary tftp> connect 192.168.1.20 tftp> put openwrt-ath79-generic-ubnt-nano-m-xw-squashfs-factory.bin Tested-by: Joe Ayers Signed-off-by: Petr Štetiar --- diff --git a/target/linux/ath79/base-files/etc/board.d/01_leds b/target/linux/ath79/base-files/etc/board.d/01_leds index 705ae3d407..0fa4bc73bb 100755 --- a/target/linux/ath79/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/base-files/etc/board.d/01_leds @@ -149,6 +149,7 @@ tplink,tl-wr841-v11) ubnt,bullet-m|\ ubnt,bullet-m-xw|\ ubnt,nano-m|\ +ubnt,nanostation-m-xw|\ ubnt,rocket-m) ucidef_set_rssimon "wlan0" "200000" "1" ucidef_set_led_rssi "rssilow" "RSSILOW" "ubnt:red:link1" "wlan0" "1" "100" diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network index f1171695bd..9a7f2d6472 100755 --- a/target/linux/ath79/base-files/etc/board.d/02_network +++ b/target/linux/ath79/base-files/etc/board.d/02_network @@ -212,6 +212,10 @@ ath79_setup_interfaces() ucidef_add_switch "switch0" \ "0@eth1" "2:lan:3" "3:lan:2" "4:lan:1" ;; + ubnt,nanostation-m-xw) + ucidef_add_switch "switch0" \ + "0@eth0" "5:lan" "1:wan" + ;; ubnt,nanostation-ac|\ ubnt,unifiac-mesh-pro|\ ubnt,unifiac-pro) diff --git a/target/linux/ath79/dts/ar9342_ubnt_nanostation-m-xw.dts b/target/linux/ath79/dts/ar9342_ubnt_nanostation-m-xw.dts new file mode 100644 index 0000000000..6ac79b0c1e --- /dev/null +++ b/target/linux/ath79/dts/ar9342_ubnt_nanostation-m-xw.dts @@ -0,0 +1,37 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include +#include + +#include "ar9342_ubnt_xw.dtsi" + +/ { + compatible = "ubnt,nanostation-m-xw", "ubnt,xw", "qca,ar9342"; + model = "Ubiquiti Nanostation M (XW)"; +}; + +&mdio0 { + status = "okay"; + + phy4-mii-enable; + phy-mask = <0x23>; + + phy4: ethernet-phy@0 { + reg = <0>; + phy-mode = "mii"; + }; +}; + +ð0 { + status = "okay"; + + phy-mode = "mii"; + phy-handle = <&phy4>; + + gmac-config { + device = <&gmac>; + mii-gmac0 = <1>; + mii-gmac0-slave = <1>; + }; +}; diff --git a/target/linux/ath79/image/generic-ubnt.mk b/target/linux/ath79/image/generic-ubnt.mk index 681c14dfb6..4f0a6a500d 100644 --- a/target/linux/ath79/image/generic-ubnt.mk +++ b/target/linux/ath79/image/generic-ubnt.mk @@ -113,6 +113,12 @@ define Device/ubnt_nano-m endef TARGET_DEVICES += ubnt_nano-m +define Device/ubnt_nanostation-m-xw + $(Device/ubnt-xw) + DEVICE_TITLE := Ubiquiti Nanostation M (XW) +endef +TARGET_DEVICES += ubnt_nanostation-m-xw + define Device/ubnt_lap-120 $(Device/ubnt-wa) DEVICE_TITLE := Ubiquiti LiteAP ac (LAP-120)