From: Andreas Böhler Date: Sat, 19 Nov 2022 23:43:50 +0000 (+0100) Subject: realtek: d-link: add support for dgs-1210-28mp-f X-Git-Tag: v23.05.0-rc1~1640 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=3e7e4d0b97595fc0c24f1d702de3daac2de3c2e7;p=openwrt%2Fstaging%2Fhauke.git realtek: d-link: add support for dgs-1210-28mp-f General hardware info: ---------------------- D-Link DGS-1210-28MP rev. F1 is a switch with 24 ethernet ports and 4 combo ports, all ports Gbit capable. It is based on a RTL8382 SoC @ 500MHz, DRAM 128MB and 32MB flash. 24 ethernet ports are 802.3af/at PoE capable with a total PoE power budget of 370W. Power over Ethernet: -------------------- The PSE hardware consists of three BCM59121 PSE chips, serving 8 ports each. They are controlled by a Nuvoton MCU. In order to enable PoE, the realtek-poe package is required. It is installed by default, but currently it requires the manual editing of /etc/config/poe. Keep in mind that the port number assignment does not match on this switch, alway 8 ports are in reversed order: 8-1, 16-9 and 24-17. LEDs and Buttons: ----------------- On stock firmware, the mode button is supposed to switch the LED indicators of all port LEDs between Link Activity and PoE status. The currently selected mode is visualized using the respective LEDs. PoE Max indicates that the maximum PoE budget has been reached. Since there is currently no support for this behavior, these LEDs and the mode button can be used independently. Serial connection: ------------------ The UART for the SoC (115200 8N1) is available via unpopulated standard 0.1" pin header marked J6. Pin1 is marked with arrow and square. Pin 1: Vcc 3.3V Pin 2: Tx Pin 3: Rx Pin 4: Gnd OEM installation from Web Interface: ------------------------------------ 1. Make sure you are booting using OEM in image 2 slot. If not, switch to image2 using the menus System > Firmware Information > Boot from image2 Tools > reboot 2. Upload image in vendor firmware via Tools > Backup / Upgrade Firmware > image1 3. Toogle startup image via System > Firmware Information > Boot from image1 4. Tools > reboot Other installation methods not tested, but since the device shares the board with the DGS-1210-28, the following should work: Boot initramfs image from U-Boot: --------------------------------- 1. Press Escape key during `Hit Esc key to stop autoboot` prompt 2. Press CTRL+C keys to get into real U-Boot prompt 3. Init network with `rtk network on` command 4. Load image with `tftpboot 0x8f000000 openwrt-rtl838x-generic-d-link_dgs-1210-28mp-f-initramfs-kernel.bin` command 5. Boot the image with `bootm` command Signed-off-by: Andreas Böhler --- diff --git a/target/linux/realtek/dts-5.10/rtl8382_d-link_dgs-1210-28.dts b/target/linux/realtek/dts-5.10/rtl8382_d-link_dgs-1210-28.dts index cf7b888fc9..0bcb196b7c 100644 --- a/target/linux/realtek/dts-5.10/rtl8382_d-link_dgs-1210-28.dts +++ b/target/linux/realtek/dts-5.10/rtl8382_d-link_dgs-1210-28.dts @@ -3,98 +3,9 @@ #include "rtl838x.dtsi" #include "rtl83xx_d-link_dgs-1210_common.dtsi" #include "rtl83xx_d-link_dgs-1210_gpio.dtsi" +#include "rtl8382_d-link_dgs-1210-28_common.dtsi" / { compatible = "d-link,dgs-1210-28", "realtek,rtl838x-soc"; model = "D-Link DGS-1210-28"; }; - -ðernet0 { - mdio: mdio-bus { - compatible = "realtek,rtl838x-mdio"; - regmap = <ðernet0>; - #address-cells = <1>; - #size-cells = <0>; - - EXTERNAL_PHY(0) - EXTERNAL_PHY(1) - EXTERNAL_PHY(2) - EXTERNAL_PHY(3) - EXTERNAL_PHY(4) - EXTERNAL_PHY(5) - EXTERNAL_PHY(6) - EXTERNAL_PHY(7) - - INTERNAL_PHY(8) - INTERNAL_PHY(9) - INTERNAL_PHY(10) - INTERNAL_PHY(11) - INTERNAL_PHY(12) - INTERNAL_PHY(13) - INTERNAL_PHY(14) - INTERNAL_PHY(15) - - EXTERNAL_PHY(16) - EXTERNAL_PHY(17) - EXTERNAL_PHY(18) - EXTERNAL_PHY(19) - EXTERNAL_PHY(20) - EXTERNAL_PHY(21) - EXTERNAL_PHY(22) - EXTERNAL_PHY(23) - - EXTERNAL_SFP_PHY(24) - EXTERNAL_SFP_PHY(25) - EXTERNAL_SFP_PHY(26) - EXTERNAL_SFP_PHY(27) - }; -}; - -&switch0 { - ports { - #address-cells = <1>; - #size-cells = <0>; - - SWITCH_PORT(0, 1, qsgmii) - SWITCH_PORT(1, 2, qsgmii) - SWITCH_PORT(2, 3, qsgmii) - SWITCH_PORT(3, 4, qsgmii) - SWITCH_PORT(4, 5, qsgmii) - SWITCH_PORT(5, 6, qsgmii) - SWITCH_PORT(6, 7, qsgmii) - SWITCH_PORT(7, 8, qsgmii) - - SWITCH_PORT(8, 9, internal) - SWITCH_PORT(9, 10, internal) - SWITCH_PORT(10, 11, internal) - SWITCH_PORT(11, 12, internal) - SWITCH_PORT(12, 13, internal) - SWITCH_PORT(13, 14, internal) - SWITCH_PORT(14, 15, internal) - SWITCH_PORT(15, 16, internal) - - SWITCH_PORT(16, 17, qsgmii) - SWITCH_PORT(17, 18, qsgmii) - SWITCH_PORT(18, 19, qsgmii) - SWITCH_PORT(19, 20, qsgmii) - SWITCH_PORT(20, 21, qsgmii) - SWITCH_PORT(21, 22, qsgmii) - SWITCH_PORT(22, 23, qsgmii) - SWITCH_PORT(23, 24, qsgmii) - - SWITCH_PORT(24, 25, qsgmii) - SWITCH_PORT(25, 26, qsgmii) - SWITCH_PORT(26, 27, qsgmii) - SWITCH_PORT(27, 28, qsgmii) - - port@28 { - ethernet = <ðernet0>; - reg = <28>; - phy-mode = "internal"; - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; -}; diff --git a/target/linux/realtek/dts-5.10/rtl8382_d-link_dgs-1210-28_common.dtsi b/target/linux/realtek/dts-5.10/rtl8382_d-link_dgs-1210-28_common.dtsi new file mode 100644 index 0000000000..17866d5f03 --- /dev/null +++ b/target/linux/realtek/dts-5.10/rtl8382_d-link_dgs-1210-28_common.dtsi @@ -0,0 +1,91 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +ðernet0 { + mdio: mdio-bus { + compatible = "realtek,rtl838x-mdio"; + regmap = <ðernet0>; + #address-cells = <1>; + #size-cells = <0>; + + EXTERNAL_PHY(0) + EXTERNAL_PHY(1) + EXTERNAL_PHY(2) + EXTERNAL_PHY(3) + EXTERNAL_PHY(4) + EXTERNAL_PHY(5) + EXTERNAL_PHY(6) + EXTERNAL_PHY(7) + + INTERNAL_PHY(8) + INTERNAL_PHY(9) + INTERNAL_PHY(10) + INTERNAL_PHY(11) + INTERNAL_PHY(12) + INTERNAL_PHY(13) + INTERNAL_PHY(14) + INTERNAL_PHY(15) + + EXTERNAL_PHY(16) + EXTERNAL_PHY(17) + EXTERNAL_PHY(18) + EXTERNAL_PHY(19) + EXTERNAL_PHY(20) + EXTERNAL_PHY(21) + EXTERNAL_PHY(22) + EXTERNAL_PHY(23) + + EXTERNAL_SFP_PHY(24) + EXTERNAL_SFP_PHY(25) + EXTERNAL_SFP_PHY(26) + EXTERNAL_SFP_PHY(27) + }; +}; + +&switch0 { + ports { + #address-cells = <1>; + #size-cells = <0>; + + SWITCH_PORT(0, 1, qsgmii) + SWITCH_PORT(1, 2, qsgmii) + SWITCH_PORT(2, 3, qsgmii) + SWITCH_PORT(3, 4, qsgmii) + SWITCH_PORT(4, 5, qsgmii) + SWITCH_PORT(5, 6, qsgmii) + SWITCH_PORT(6, 7, qsgmii) + SWITCH_PORT(7, 8, qsgmii) + + SWITCH_PORT(8, 9, internal) + SWITCH_PORT(9, 10, internal) + SWITCH_PORT(10, 11, internal) + SWITCH_PORT(11, 12, internal) + SWITCH_PORT(12, 13, internal) + SWITCH_PORT(13, 14, internal) + SWITCH_PORT(14, 15, internal) + SWITCH_PORT(15, 16, internal) + + SWITCH_PORT(16, 17, qsgmii) + SWITCH_PORT(17, 18, qsgmii) + SWITCH_PORT(18, 19, qsgmii) + SWITCH_PORT(19, 20, qsgmii) + SWITCH_PORT(20, 21, qsgmii) + SWITCH_PORT(21, 22, qsgmii) + SWITCH_PORT(22, 23, qsgmii) + SWITCH_PORT(23, 24, qsgmii) + + SWITCH_PORT(24, 25, qsgmii) + SWITCH_PORT(25, 26, qsgmii) + SWITCH_PORT(26, 27, qsgmii) + SWITCH_PORT(27, 28, qsgmii) + + port@28 { + ethernet = <ðernet0>; + reg = <28>; + phy-mode = "internal"; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; +}; diff --git a/target/linux/realtek/dts-5.10/rtl8382_d-link_dgs-1210-28mp-f.dts b/target/linux/realtek/dts-5.10/rtl8382_d-link_dgs-1210-28mp-f.dts new file mode 100644 index 0000000000..ce008229b3 --- /dev/null +++ b/target/linux/realtek/dts-5.10/rtl8382_d-link_dgs-1210-28mp-f.dts @@ -0,0 +1,40 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "rtl838x.dtsi" +#include "rtl83xx_d-link_dgs-1210_common.dtsi" +#include "rtl83xx_d-link_dgs-1210_gpio.dtsi" +#include "rtl8382_d-link_dgs-1210-28_common.dtsi" + +/ { + compatible = "d-link,dgs-1210-28mp-f", "realtek,rtl8382-soc", "realtek,rtl838x-soc"; + model = "D-Link DGS-1210-28MP F"; +}; + +&leds { + link_act { + label = "green:link_act"; + gpios = <&gpio1 28 GPIO_ACTIVE_LOW>; + }; + + poe { + label = "green:poe"; + gpios = <&gpio1 29 GPIO_ACTIVE_LOW>; + }; + + poe_max { + label = "yellow:poe_max"; + gpios = <&gpio1 27 GPIO_ACTIVE_LOW>; + }; +}; + +&keys { + mode { + label = "mode"; + gpios = <&gpio1 30 GPIO_ACTIVE_LOW>; + linux,code = ; + }; +}; + +&uart1 { + status = "okay"; +}; diff --git a/target/linux/realtek/image/rtl838x.mk b/target/linux/realtek/image/rtl838x.mk index c33ac7c5c4..eef66c89ce 100644 --- a/target/linux/realtek/image/rtl838x.mk +++ b/target/linux/realtek/image/rtl838x.mk @@ -50,6 +50,15 @@ define Device/d-link_dgs-1210-28 endef TARGET_DEVICES += d-link_dgs-1210-28 +define Device/d-link_dgs-1210-28mp-f + $(Device/d-link_dgs-1210) + SOC := rtl8382 + DEVICE_MODEL := DGS-1210-28MP + DEVICE_VARIANT := F + DEVICE_PACKAGES += realtek-poe +endef +TARGET_DEVICES += d-link_dgs-1210-28mp-f + # The "IMG-" uImage name allows flashing the iniramfs from the vendor Web UI. # Avoided for sysupgrade, as the vendor FW would do an incomplete flash. define Device/engenius_ews2910p